GENERAL TOLERANCES
(UNLESS SPECIFIED)
MM
INCH
4 PLACES
± ±
3 PLACES
± ±
0.01
2 PLACES
±
0.25
±
1 PLACES
±
0.35
±
0 PLACES
± ±
ANGULAR TOL
±
0.5
DRAFT WHERE APPLICABLE
MUST REMAIN
WITHIN DIMENSIONS
SERIES MATERIAL NUMBER CUSTOMER
GENERAL MARKET
3001
SEE CHART
THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
SHEET NUMBER
1 OF 1
DIMENSION UNITS SCALE
MM 4:1
DRWN BY DATE
P.MOORE 1998/09/15
CHK'D BY DATE
MGOONEY 1999/03/12
APPR BY DATE
FSMITH 2010/12/06
DOCUMENT NUMBER
DOC TYPE
DOC PART
SDE-3001-N-X PSD 001
DRAWING SIZE
THIRD ANGLE PROJECTION
A3
KK (5.08)/.200
CRIMP TERMINAL HOUSING
PRODUCT CUSTOMER DRAWING
DRAWING UPDATED
2018/02/05
2018/02/06
2018/02/08
171927
PKH
SS06
ISHWARG
EC NO:
DRWN:
CHK'D:
APPR:
T
REV
QUALITY
SYMBOLS
=0
=0
=0
=0
=0
=0
=0
=0
FORMAT: Met-lega-master-tb-prod-A3
REVISION: C
DATE: 2017/02/06
DOCUMENT STATUS P1 RELEASE DATE 2018/02/08 12:08:36
C
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
A A
B B
C C
D D
E E
Z
ZSECTION Z-Z
15.90
±
0.40
SERIES NO.
SQUARE HOLE
TYP
2.00
±
0.15
OPTIONAL VOIDED CIRCUIT
SEE SHEET 2
1.00
CIRCUIT 1
SEE NOTE 6
B
A= =
5.08
±
0.10
6.00
±
0.25
ROUND OR SQUARE WIRE PIN.
1.14
±
0.15
10-01-1124
E-3001-12
55.88 +0.50
-0.25 60.96 +0.60
-0.30
-1114
-11
50.80 +0.45
-0.20 55.88 +0.55
-0.30
-1104
-10
45.72 +0.30
-0.20 50.80 +0.40
-0.20
-1094
-9
40.64 +0.25
-0.20 45.72 +0.40
-0.20
-1084
-8
35.56
±
0.20 40.64 +0.35
-0.20
-1074
-7
30.48
±
0.20 35.56 +0.30
-0.20
-1064
-6
25.40 +0.15
-0.10 30.48 +0.25
-0.20
-1054
-5
20.32 +0.15
-0.10 25.40 +0.25
-0.15
-1044
-4
15.24
±
0.10 20.32 +0.20
-0.15
-1034
-3
10.16
±
0.10 15.24 +0.20
-0.15
10-01-1024
E-3001-2
5.08
±
0.10 10.16 +0.10
-0.15
AB
PART NO.
ENG NO.
DIMENSION
NOTES:
1. MATERIAL: NYLON, UL94V-2, COLOR: NATURAL
2. FINISH: N/A
3. PRODUCT SPECIFICATION: PS-99020-0087
4. THIS HOUSING USES KK TERMINAL SERIES 2478, 2578, AND 2878.
5. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF
COSMETIC SPECIFICATION PS-45499-002.
6. CIRCUIT 1 USED TO DEFINE VOID LOCATION.
7. WINDOW GEOMETRY IS DEPENDENT ON MOLD. PARTS MAY
HAVE EITHER GEOMETRY.
4.43
REF
Y
SECTION Y-Y
OPTIONAL WINDOW DETAIL
SEE NOTE 7
Y
