IDT5T93GL161 2.5V LVDS 1:16 GLITCHLESS CLOCK BUFFER TERABUFFER II INDUSTRIAL TEMPERATURE RANGE 2.5V LVDS 1:16 GLITCHLESS CLOCK BUFFER TERABUFFERTM II DESCRIPTION: FEATURES: * * * * * * * * * * * IDT5T93GL161 The IDT5T93GL161 2.5V differential clock buffer is a user-selectable differential input to sixteen LVDS outputs . The fanout from a differential input to sixteen LVDS outputs reduces loading on the preceding driver and provides an efficient clock distribution network. The IDT5T93GL161 can act as a translator from a differential HSTL, eHSTL, LVEPECL (2.5V), LVPECL (3.3V), CML, or LVDS input to LVDS outputs. A single-ended 3.3V / 2.5V LVTTL input can also be used to translate to LVDS outputs. The redundant input capability allows for a glitchless change-over from a primary clock source to a secondary clock source. Selectable inputs are controlled by SEL. During the switchover, the output will disable low for up to three clock cycles of the previously-selected input clock. The outputs will remain low for up to three clock cycles of the newlyselected clock, after which the outputs will start from the newly-selected input. A FSEL pin has been implemented to control the switchover in cases where a clock source is absent or is driven to DC levels below the minimum specifications. The IDT5T93GL161 outputs can be asynchronously enabled/disabled. When disabled, the outputs will drive to the value selected by the GL pin. Multiple power and grounds reduce noise. Guaranteed Low Skew < 75ps (max) Very low duty cycle distortion < 100ps (max) High speed propagation delay < 2.2ns (max) Up to 450MHz operation Selectable inputs Hot insertable and over-voltage tolerant inputs 3.3V / 2.5V LVTTL, HSTL, eHSTL, LVEPECL (2.5V), LVPECL (3.3V), CML, or LVDS input interface Selectable differential inputs to sixteen LVDS outputs Power-down mode 2.5V VDD Available in TQFP package APPLICATIONS: * Clock distribution FUNCTIONAL BLOCK DIAGRAM GL G1 PD A1 OUTPUT CONTROL Q1 OUTPUT CONTROL Q2 OUTPUT CONTROL Q3 OUTPUT CONTROL Q4 OUTPUT CONTROL Q5 OUTPUT CONTROL Q6 OUTPUT CONTROL Q7 OUTPUT CONTROL Q8 OUTPUT CONTROL Q9 OUTPUT CONTROL Q10 OUTPUT CONTROL Q11 OUTPUT CONTROL Q12 OUTPUT CONTROL Q13 OUTPUT CONTROL Q14 OUTPUT CONTROL Q15 OUTPUT CONTROL Q16 Q1 Q2 Q3 Q4 Q5 1 A1 A2 0 A2 SEL FSEL G2 The IDT logo is a registered trademark of Integrated Device Technology, Inc. INDUSTRIAL TEMPERATURE RANGE Q6 Q7 Q8 Q9 Q10 Q11 Q12 Q13 Q14 Q15 Q16 JANUARY 2007 1 (c) 2007 Integrated Device Technology, Inc. DSC 6742/4 IDT5T93GL161 2.5V LVDS 1:16 GLITCHLESS CLOCK BUFFER TERABUFFER II INDUSTRIAL TEMPERATURE RANGE FSEL PD GND VDD Q13 Q13 Q14 Q14 Q15 Q15 Q16 Q16 VDD VDD GND SEL PIN CONFIGURATION 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 G1 1 48 G2 GND 2 47 GND GND 3 46 GND VDD 4 45 VDD Q1 5 44 Q12 Q1 6 43 Q12 Q2 7 42 Q11 Q2 8 41 Q11 Q3 9 40 Q10 Q3 10 39 Q10 Q4 11 38 Q9 Q4 12 37 Q9 VDD 13 36 VDD A1 14 35 A2 A1 15 34 A2 GND 16 33 GND TQFP TOP VIEW 2 GND VDD NC NC Q8 Q8 Q7 Q7 Q6 Q6 Q5 Q5 VDD VDD GND GL 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 IDT5T93GL161 2.5V LVDS 1:16 GLITCHLESS CLOCK BUFFER TERABUFFER II INDUSTRIAL TEMPERATURE RANGE CAPACITANCE(1) (TA = +25C, F = 1.0MHz) ABSOLUTE MAXIMUM RATINGS(1) Max Unit VDD Symbol Power Supply Voltage Description -0.5 to +3.6 V VI Input Voltage -0.5 to +3.6 V VO Output Voltage(2) -0.5 to VDD +0.5 V TSTG Storage Temperature -65 to +150 C TJ Junction Temperature 150 C Symbol CIN Parameter Min Typ. Max. Unit Input Capacitance -- -- 3 pF NOTE: 1. This parameter is measured at characterization but not tested NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. Not to exceed 3.6V. RECOMMENDED OPERATING RANGE Symbol TA VDD Description Ambient Operating Temperature Internal Power Supply Voltage Min. -40 2.3 Typ. +25 2.5 Max. +85 2.7 Unit C V PIN DESCRIPTION Symbol A[1:2] A[1:2] I/O I I Type Adjustable(1,4) Adjustable(1,4) G1 I LVTTL G2 I LVTTL GL I LVTTL Qn Qn SEL PD O O I I LVDS LVDS LVTTL LVTTL FSEL VDD I LVTTL PWR Description Clock input. A[1:2] is the "true" side of the differential clock input. Complementary clock inputs. A[1:2] is the complementary side of A[1:2]. For LVTTL single-ended operation, A[1:2] should be set to the desired toggle voltage for A[1:2]: 3.3V LVTTL VREF = 1650mV 2.5V LVTTL VREF = 1250mV Gate control for differential outputs Q1 and Q1 through Q8 and Q8. When G1 is LOW, the differential outputs are active. When G1 is HIGH, the differential outputs are asynchronously driven to the level designated by GL(2). Gate control for differential outputs Q9 and Q9 through Q16 and Q16. When G2 is LOW, the differential outputs are active. When G2 is HIGH, the differential outputs are asynchronously driven to the level designated by GL(2). Specifies output disable level. If HIGH, "true" outputs disable HIGH and "complementary" outputs disable LOW. If LOW, "true" outputs disable LOW and "complementary" outputs disable HIGH. Clock outputs Complementary clock outputs Reference clock select. When LOW, selects A2 and A2. When HIGH, selects A1 and A1. Power-down control. Shuts off entire chip. If LOW, the device goes into low power mode. Inputs and outputs are disabled. Both "true" and "complementary" outputs will pull to VDD. Set HIGH for normal operation.(3) At a rising edge, FSEL forces select to the input designated by SEL. Set LOW for normal operation. Power supply for the device core and inputs PWR Ground GND NOTES: 1. Inputs are capable of translating the following interface standards: Single-ended 3.3V and 2.5V LVTTL levels Differential HSTL and eHSTL levels Differential LVEPECL (2.5V) and LVPECL (3.3V) levels Differential LVDS levels Differential CML levels 2. Because the gate controls are asynchronous, runt pulses are possible. It is the user's responsibility to either time the gate control signals to minimize the possibility of runt pulses or be able to tolerate them in down stream circuitry. 3. It is recommended that the outputs be disabled before entering power-down mode. It is also recommended that the outputs remain disabled until the device completes powerup after asserting PD. 4. The user must take precautions with any differential input interface standard being used in order to prevent instability when there is no input signal. 3 IDT5T93GL161 2.5V LVDS 1:16 GLITCHLESS CLOCK BUFFER TERABUFFER II INDUSTRIAL TEMPERATURE RANGE DC ELECTRICAL CHARACTERISTICS OVER RECOMMENDED OPERATING RANGE FOR LVTTL(1) Symbol Parameter Input Characteristics IIH Input HIGH Current IIL Input LOW Current VIK Clamp Diode Voltage VIN DC Input Voltage VIH DC Input HIGH VIL DC Input LOW VTHI DC Input Threshold Crossing Voltage Single-Ended Reference Voltage(3) VREF Test Conditions VDD = 2.7V VDD = 2.7V VDD = 2.3V, IIN = -18mA 3.3V LVTTL 2.5V LVTTL Min. Typ.(2) Max Unit -- -- -- - 0.3 1.7 -- -- -- - 0.7 5 5 - 1.2 +3.6 -- 0.7 A -- -- VDD/2 1.65 1.25 -- -- V V V V V V NOTES: 1. See RECOMMENDED OPERATING RANGE table. 2. Typical values are at VDD = 2.5V, +25C ambient. 3. For A[1:2] single-ended operation, A[1:2] is tied to a DC reference voltage. DC ELECTRICAL CHARACTERISTICS OVER RECOMMENDED OPERATING RANGE FOR DIFFERENTIAL INPUTS(1) Symbol Parameter Input Characteristics IIH Input HIGH Current IIL Input LOW Current VIK Clamp Diode Voltage VIN DC Input Voltage VDIF DC Differential Voltage(2) VCM DC Common Mode Input Voltage(3) Test Conditions VDD = 2.7V VDD = 2.7V VDD = 2.3V, IIN = -18mA Min. Typ.(4) Max Unit -- -- -- - 0.3 0.1 0.05 -- -- - 0.7 5 5 - 1.2 +3.6 -- VDD A V V V V NOTES: 1. See RECOMMENDED OPERATING RANGE table. 2. VDIF specifies the minimum input differential voltage (VTR - VCP) required for switching where VTR is the "true" input level and VCP is the "complement" input level. The DC differential voltage must be maintained to guarantee retaining the existing HIGH or LOW input. The AC differential voltage must be achieved to guarantee switching to a new state. 3. VCM specifies the maximum allowable range of (VTR + VCP) /2. 4. Typical values are at VDD = 2.5V, +25C ambient. DC ELECTRICAL CHARACTERISTICS OVER RECOMMENDED OPERATING RANGE FOR LVDS(1) Symbol Parameter Output Characteristics VOT(+) Differential Output Voltage for the True Binary State VOT(-) Differential Output Voltage for the False Binary State VOT Change in VOT Between Complementary Output States VOS Output Common Mode Voltage (Offset Voltage) VOS Change in VOS Between Complementary Output States IOS Outputs Short Circuit Current Differential Outputs Short Circuit Current IOSD Test Conditions Min. Typ.(2) Max Unit VOUT + and VOUT - = 0V VOUT + = VOUT - 247 247 -- 1.125 -- -- -- -- -- -- 1.2 -- 12 6 454 454 50 1.375 50 24 12 mV mV mV V mV mA mA NOTES: 1. See RECOMMENDED OPERATING RANGE table. 2. Typical values are at VDD = 2.5V, +25C ambient. 4 IDT5T93GL161 2.5V LVDS 1:16 GLITCHLESS CLOCK BUFFER TERABUFFER II INDUSTRIAL TEMPERATURE RANGE DIFFERENTIAL INPUT AC TEST CONDITIONS FOR HSTL Symbol Parameter VDIF Input Signal Swing(1) Value Units 1 V VX Differential Input Signal Crossing Point 750 mV DH Duty Cycle 50 % VTHI Input Timing Measurement Reference Level tR, tF Input Signal Edge Rate(4) (2) (3) Crossing Point V 2 V/ns NOTES: 1. The 1V peak-to-peak input pulse level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VDIF (AC) specification under actual use conditions. 2. A 750mV crossing point level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VX specification under actual use conditions. 3. In all cases, input waveform timing is marked at the differential cross-point of the input signals. 4. The input signal edge rate of 2V/ns or greater is to be maintained in the 20% to 80% range of the input waveform. DIFFERENTIAL INPUT AC TEST CONDITIONS FOR eHSTL Symbol Parameter VDIF Input Signal Swing(1) Value Units 1 V VX Differential Input Signal Crossing Point 900 mV DH Duty Cycle 50 % VTHI Input Timing Measurement Reference Level tR, tF Input Signal Edge Rate(4) (2) (3) Crossing Point V 2 V/ns NOTES: 1. The 1V peak-to-peak input pulse level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VDIF (AC) specification under actual use conditions. 2. A 900mV crossing point level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VX specification under actual use conditions. 3. In all cases, input waveform timing is marked at the differential cross-point of the input signals. 4. The input signal edge rate of 2V/ns or greater is to be maintained in the 20% to 80% range of the input waveform. DIFFERENTIAL INPUT AC TEST CONDITIONS FOR LVEPECL (2.5V) AND LVPECL (3.3V) Symbol Parameter VDIF Input Signal Swing(1) VX Differential Input Signal Crossing Point (2) DH Duty Cycle VTHI Input Timing Measurement Reference Level(3) tR, tF Input Signal Edge Rate Value Units 732 mV LVEPECL 1082 mV LVPECL 1880 (4) 50 % Crossing Point V 2 V/ns NOTES: 1. The 732mV peak-to-peak input pulse level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VDIF (AC) specification under actual use conditions. 2. 1082mV LVEPECL (2.5V) and 1880mV LVPECL (3.3V) crossing point levels are specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VX specification under actual use conditions. 3. In all cases, input waveform timing is marked at the differential cross-point of the input signals. 4. The input signal edge rate of 2V/ns or greater is to be maintained in the 20% to 80% range of the input waveform. 5 IDT5T93GL161 2.5V LVDS 1:16 GLITCHLESS CLOCK BUFFER TERABUFFER II INDUSTRIAL TEMPERATURE RANGE DIFFERENTIAL INPUT AC TEST CONDITIONS FOR LVDS Symbol Parameter VDIF Input Signal Swing(1) Value Units 400 mV VX Differential Input Signal Crossing Point 1.2 V DH Duty Cycle 50 % VTHI Input Timing Measurement Reference Level(3) tR, tF Input Signal Edge Rate(4) (2) Crossing Point V 2 V/ns NOTES: 1. The 400mV peak-to-peak input pulse level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VDIF (AC) specification under actual use conditions. 2. A 1.2V crossing point level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VX specification under actual use conditions. 3. In all cases, input waveform timing is marked at the differential cross-point of the input signals. 4. The input signal edge rate of 2V/ns or greater is to be maintained in the 20% to 80% range of the input waveform. AC DIFFERENTIAL INPUT SPECIFICATIONS(1) Symbol Parameter Min. Typ. Max Unit VDIF AC Differential Voltage 0.1 -- 3.6 V VIX VCM Differential Input Crosspoint Voltage Common Mode Input Voltage Range(3) 0.05 0.05 -- -- VDD VDD V V VIN Input Voltage - 0.3 +3.6 V (2) NOTES: 1. The output will not change state until the inputs have crossed and the minimum differential voltage defined by VDIF has been met or exceeded. 2. VDIF specifies the minimum input voltage (VTR - VCP) required for switching where VTR is the "true" input level and VCP is the "complement" input level. The AC differential voltage must be achieved to guarantee switching to a new state. 3. VCM specifies the maximum allowable range of (VTR + VCP) /2. POWER SUPPLY CHARACTERISTICS FOR LVDS OUTPUTS(1) Symbol IDDQ ITOT IPD Parameter Quiescent VDD Power Supply Current Total Power VDD Supply Current Total Power Down Supply Current Test Conditions VDD = Max., All Input Clocks = LOW(2) Outputs enabled VDD = 2.7V., FREFERENCE CLOCK = 450MHz PD = LOW NOTES: 1. These power consumption characteristics are for all the valid input interfaces and cover the worst case conditions. 2. The true input is held LOW and the complementary input is held HIGH. 6 Typ. -- Max 350 Unit mA -- -- 360 5 mA mA IDT5T93GL161 2.5V LVDS 1:16 GLITCHLESS CLOCK BUFFER TERABUFFER II INDUSTRIAL TEMPERATURE RANGE AC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE(1,5) Symbol Skew Parameters tSK(O) tSK(P) Parameter Min. Typ. Max Unit Same Device Output Pin-to-Pin Skew(2) Pulse Skew(3) -- -- -- -- 75 100 ps ps tSK(PP) Propagation Delay tPLH tPHL Part-to-Part Skew(4) -- -- 300 ps Propagation Delay A, A Crosspoint to Qn, Qn Crosspoint -- 1.5 2.2 ns -- -- 450 MHz fO Frequency Range(6) Output Gate Enable/Disable Delay tPGE tPGD Power Down Timing tPWRDN tPWRUP Output Gate Enable Crossing VTHI to Qn/Qn Crosspoint -- -- 3.5 ns Output Gate Disable Crossing VTHI to Qn/Qn Crosspoint Driven to GL Designated Level -- -- 3.5 ns PD Crossing VTHI to Qn = VDD, Qn = VDD Output Gate Disable Crossing VTHI to Qn/Qn Driven to GL Designated Level -- -- -- -- 100 100 S S NOTES: 1. AC propagation measurements should not be taken within the first 100 cycles of startup. 2. Skew measured between crosspoints of all differential output pairs under identical input and output interfaces, transitions and load conditions on any one device. 3. Skew measured is the difference between propagation delay times tPHL and tPLH of any single differential output pair under identical input and output interfaces, transitions and load conditions on any one device. 4. Skew measured is the magnitude of the difference in propagation times between any single differential output pair of two devices, given identical transitions and load conditions at identical VDD levels and temperature. 5. All parameters are tested with a 50% input duty cycle. 6. Guaranteed by design but not production tested. 7 IDT5T93GL161 2.5V LVDS 1:16 GLITCHLESS CLOCK BUFFER TERABUFFER II INDUSTRIAL TEMPERATURE RANGE DIFFERENTIAL AC TIMING WAVEFORMS 1/fo + VDIF VDIF = 0 - VDIF A[1:2] - A[1:2] tPHL tPLH + VDIF VDIF = 0 - VDIF Qn - Qn tSK(O) tSK(O) Qm - Qm Output Propagation and Skew Waveforms NOTES: 1. Pulse skew is calculated using the following expression: tSK(P) = | tPHL - tPLH | Note that the tPHL and tPLH shown above are not valid measurements for this calculation because they are not taken from the same pulse. 2. AC propagation measurements should not be taken within the first 100 cycles of startup. 8 + VDIF VDIF = 0 - VDIF IDT5T93GL161 2.5V LVDS 1:16 GLITCHLESS CLOCK BUFFER TERABUFFER II INDUSTRIAL TEMPERATURE RANGE + VDIF VDIF = 0 - VDIF A[1:2] - A[1:2] VIH VTHI VIL GL tPLH VIH VTHI VIL Gx tPGE tPGD + VDIF VDIF = 0 - VDIF Qn - Qn Differential Gate Disable/Enable Showing Runt Pulse Generation NOTE: 1. As shown, it is possible to generate runt pulses on gate disable and enable of the outputs. It is the user's responsibility to time their Gx signals to avoid this problem. A1 - A1 + VDIF VDIF = 0 - VDIF A2 - A2 + VDIF VDIF = 0 - VDIF VIH VTHI VIL SEL + VDIF VDIF = 0 - VDIF Qn - Qn Glitchless Output Operation with Switching Input Clock Selection NOTES: 1. When SEL changes, the output clock goes LOW on the falling edge of the output clock up to three cycles later. The output then stays LOW for up to three clock cycles of the new input clock. After this, the output starts with the rising edge of the new input clock. 2. AC propagation measurements should not be taken within the first 100 cycles of startup. 9 IDT5T93GL161 2.5V LVDS 1:16 GLITCHLESS CLOCK BUFFER TERABUFFER II INDUSTRIAL TEMPERATURE RANGE FSEL Operation for When Current Clock Dies NOTES: 1. When the differential on the selected clock goes below the minimum DC differential, the outputs clock goes to an unknown state. When this happens, the SEL pin should be toggled and FSEL asserted in order to force selection of the new input clock. The output clock will start up after a number of cycles of the newly-selected input clock. 2. The FSEL pin should stay asserted until the problem with the dead clock can be fixed in the system. 3. It is recommended that the FSEL be tied HIGH for systems that use only one input. If this is not possible, the user must guarantee that the unused input have a differential greater than or equal to the minimum DC differential specified in the datasheet. FSEL Operation for When Opposite Clock Dies NOTES: 1. When the differential on the non-selected clock goes below the minimum DC differential, the outputs clock goes to an unknown state. When this happens, the FSEL pin should be asserted in order to force selection of the new input clock. The output clock will start up after a number of cycles of the newly-selected input clock. 2. The FSEL pin should stay asserted until the problem with the dead clock can be fixed in the system. 3. It is recommended that the FSEL be tied HIGH for systems that use only one input. If this is not possible, the user must guarantee that the unused input have a differential greater than or equal to the minimum DC differential specified in the datasheet. 10 IDT5T93GL161 2.5V LVDS 1:16 GLITCHLESS CLOCK BUFFER TERABUFFER II INDUSTRIAL TEMPERATURE RANGE A1 - A1 +VDIF VDIF=0 -VDIF A2 - A2 +VDIF VDIF=0 -VDIF FSEL VIH VTHI VIL SEL VIH VTHI VIL +VDIF VDIF=0 -VDIF Qn - Qn Selection of Input While Protecting Against When Opposite Clock Dies NOTES: 1. If the user holds FSEL HIGH, the output will not be affected by the deselected input clock. 2. The output will immediately be driven to LOW once FSEL is asserted. This may cause glitching on the output. The output will restart with the input clock selected by the SEL pin. 3. If the user decides to switch input clocks, the user must de-assert FSEL, then assert FSEL after toggling the SEL input pin. The output will be driven LOW and will restart with the input clock selected by the SEL pin. A1 - A1 +VDIF VDIF=0 -VDIF A2 - A2 +VDIF VDIF=0 -VDIF Gx VIH VTHI VIL PD VIH VTHI VIL +VDIF VDIF=0 -VDIF Qn - Qn Power Down Timing NOTES: 1. It is recommended that outputs be disabled before entering power-down mode. It is also recommended that the outputs remain disabled until the device completes power-up after asserting PD. 2. The POWER DOWN TIMING diagram assumes that GL is HIGH. 3. It should be noted that during power-down mode, the outputs are both pulled to VDD. In the POWER DOWN TIMING diagram this is shown when Qn - Qn goes to VDIF = 0. 11 IDT5T93GL161 2.5V LVDS 1:16 GLITCHLESS CLOCK BUFFER TERABUFFER II INDUSTRIAL TEMPERATURE RANGE TEST CIRCUITS AND CONDITIONS VIN ~50 Transmission Line VDD/2 A D.U.T. Pulse Generator VIN A ~50 Transmission Line -VDD/2 Scope 50 50 Test Circuit for Differential Input DIFFERENTIAL INPUT TEST CONDITIONS Symbol VDD = 2.5V 0.2V Unit VTHI Crossing of A and A V 12 IDT5T93GL161 2.5V LVDS 1:16 GLITCHLESS CLOCK BUFFER TERABUFFER II INDUSTRIAL TEMPERATURE RANGE VDD A Pulse Generator Qn RL A D.U.T. VOS VOD RL Qn Test Circuit for DC Outputs and Power Down Tests VDD/2 SCOPE CL Z = 50 Pulse Generator A Qn 50 A D.U.T. 50 Qn Z = 50 CL -VDD/2 Test Circuit for Propagation, Skew, and Gate Enable/Disable Timing LVDS OUTPUT TEST CONDITION Symbol VDD = 2.5V 0.2V Unit CL 0(1) 8(1,2) pF RL 50 NOTES: 1. Specifications only apply to "Normal Operations" test condition. The TIA/EIA specification load is for reference only. 2. The scope inputs are assumed to have a 2pF load to ground. TIA/EIA - 644 specifies 5pF between the output pair. With CL = 8pF, this gives the test circuit appropriate 5pF equivalent load. 13 IDT5T93GL161 2.5V LVDS 1:16 GLITCHLESS CLOCK BUFFER TERABUFFER II INDUSTRIAL TEMPERATURE RANGE ORDERING INFORMATION IDT XX XXXXX Device Type Package X Process I -40C to +85C (Industrial) PF PFG Thin Quad Flat Pack TQFP - Green 5T93GL161 2.5V LVDS 1:16 Glitchless Clock Buffer TerabufferTM II CORPORATE HEADQUARTERS 6024 Silver Creek Valley Road San Jose, CA 95138 for SALES: 800-345-7015 or 408-284-8200 fax: 408-284-2775 www.idt.com 14 for Tech Support: clockhelp@idt.com