H7CN-XHNS AC100-240 - Omron Automation and Safety

CSM_H7CN_DS_E_2_1

Solid-state Counter

H7CN

All Required Counter Functions

Incorporated in a Compact DIN-sized

(48 × 48) Housing

• In addition to Up and Down models, a reversible (Up-Down)

counter is also available

• Maximum counting speed of 5,000 cps, never before attained by

a small-size preset counter

• Power supply freely selectable within a range of 100 to 240 VAC.

Also, power supply for the DC-operated models is selectable

within a range of 12 to 48 V

• Models with memory backup function against power failure

available

For the most recent information on models that have been certified for

safety standards, refer to your OMRON website.

Ordering Information

Note: 1. Only the transistor input signal is available when the maximum counting speed is 5,000 cps

2. Specify the power supply voltage when ordering.

■Accessories (Order Separately)

Sockets

Classification Preset Counter Totalizing

Counter

Input signal

system (Count &

reset inputs)

Contact, Transistor Contact/Transistor

Mounting method Flush mounting, surface mounting

Display 7-segment LEDs (10 mm high), Up indicator 7-segment LEDs

(10 mm high)

Number of digits 4 digits (0 to 9,999)

Backup power for

memory protection

No Yes (100 to 240 VAC

only)

No Yes

Control output Contact (SPST-NO) Contact (SPDT) Contact (SPST-NO) Transistor (open-

collector)

---

Operating mode Up counting Down

counting

Down

counting

Reversible

counting,

command

input

Reversible

counting,

individual input

counting

Down

counting

Up counting

Max.

counting

speed

30 cps H7CN-XLN H7CN-YLN H7CN-

XLNM

H7CN-

YLNM

H7CN-ALN H7CN-BLN --- --- H7CN-TXL

5 kcps

(see

note 1.)

H7CN-XHN H7CN-YHN H7CN-

XHNM

H7CN-

YHNM

H7CN-AHN H7CN-BHN H7CN-

XHNS

H7CN-

YHNS

H7CN-TXH

Protective Cover Hard Y92A-48B

Soft Y92A-48D

Flush Mounting Adapter Y92F-30

Applicable Counter Track Mounted

Socket

Back Connecting

Socket

H7CN-@@ P2CF-08(-E) P3G-08

H7CN-@@M P2CF-11(-E) P3GA-11

H7CN

Specifications

■Ratings

Note: 1. The memory backup function is not available for this DC supply voltage range.

2. On power application, an inrush current of approximately 10 times the normal current flows through the Counter.

■Characteristics

Supply voltage 24, 100 to 240 VAC 50/60 Hz

12 to 48 VDC (contains 20% ripple max.) (see note 1)

Operating voltage range 85% to 110% of rated voltage

Power consumption

(see note 2)

Approx. 12 VA/2.5 W (at 240 VAC, 50Hz)

Approx. 2.5 W (at 48 VDC)

Count and reset input Impedance by short-circuiting contacts: 1 kΩ max.

Residual voltage: 2 V max.

Impedance by opening contacts: 100 kΩ min.

Max. counting speeds of

count input

30 cps (contact and transistor inputs)

Minimum pulse width: 16.7 ms (ON/OFF ratio: 1:1)

5.000 cps (transistor inputs)

Minimum pulse width: 0.1 ms (ON/OFF ratio: 1:1)

Reset system Power-OFF reset

Reset time: 0.5 s

Reset time following power application 0.05 s

External reset & manual reset

Reset time: 0.02 s

Reset time following signal application: 0.05 s

Control output Contact (SPDT) output:

3 A, 250 VAC, cosϕ = 1 (resistive load)

Transistor (open collector) output:

30 VDC MAX. 100 mA max.

Case color Light gray (Munsell 5Y7/1)

Item Preset Counter Totalizing Counter

Insulation resistance 100 MΩ min. (at 500 VDC) (between current-carrying

terminal and exposed non-current-carrying metal parts,

and between non-continuous contacts)

100 MΩ min. (at 500 VDC) (between current-carrying

terminal and exposed non-current-carrying metal parts)

Dielectric strength 2,000 VAC, 50/60 Hz for 1 min (between current-

carrying terminal and exposed non-current carrying

metal parts and between non-continuous contacts)

2,000 VAC, 50/60 Hz for 1 min (between current-

carrying terminal and exposed non-current carrying

metal parts)

Impulse withstand voltage 6 kV (between power terminals)

6 kV (between current-carrying terminal and exposed non-current-carrying metal parts)

Noise immunity ±2 kV (between power terminals),

±500 V (between input terminals),

square-wave noise by noise simulator

Static immunity Malfunction: 8 kV

Vibration resistance Destruction: 10 to 55 Hz, 0.75-mm single amplitude

Malfunction: 10 to 55 Hz, 0.5-mm single amplitude

Shock resistance Destruction: 300 m/s2 (approx. 30G)

Malfunction: 100 m/s2 (approx. 10G)

Ambient temperature Operating: –10°C to 55°C (with no icing)

Storage: –25°C to 65°C (with no icing)

Ambient humidity 35% to 85%

Life expectancy Mechanical: 10 million operations min.

Electrical: 100,000 operations min.

(3 A at 250 VAC, resistive load)

---

Approved standards UL508, CSA C22.2 No.14

Weight Approx. 110 g

H7CN

Engineering Data

Electrical Life Expectancy

Operation

■Timing Charts

Preset Counter

(Resistive load) (Inductive load)

Load current (A) Load current (A)

Reset

Preset

Count-up

Reset

Preset

Count-up

Reset

Preset

Count-up

Up Type Down Type

Up/Down A, B Types

Digital

display

Digital

display

Digital

display

Control

output

Control

output

Control

output

H7CN

Totalizing Counter

Input Mode

Up/Down Selectable Type

Note: (A) must be more than the minimum signal width. If (A) is set shorter than the minimum signal width, the error of count ±1 may occur.

Up/Down Type

Note: A) must be more than the minimum signal width. If (A) is set shorter than the minimum signal width, the error of count ±1 may occur.

H: Short-circuit ON-time impedance; 1 kΩ max. Residual voltage; 0.5 V max.

L: Open circuit OFF-time impedance; 100 kΩ min.

Up Type

Reset

*Full scale

Digital display

* Full scale: 9999

Up mode Down mode

Count input 1: Count input; Count input 2: Inhibit (gate) input

Count

input 1

Count

input 2

Inhibited

Count value

Note: Input to the CP2 while the CP1 is set to "L."

Count

input 1

Count

input 2

Inhibited

Count value

Count input 1: Count input; Count input 2: Inhibit (gate) input

Note: Input to the CP2 while the CP1 is set to "L."

Count input 1: Inhibit (gate) input; Count input 2: Count input

Count

input 1

Count

input 2

Inhibited

Count value

Note: Input to the CP1 while the CP2 is set to "H."

Count

input 1

Count

input 2

Inhibited

Count value

Count input 1: Inhibit (gate) input; Count input 2: Count input

Note: Input to the CP1 while the CP2 is set to "H."

Up/Down A command input

Count

input 1

Count

input 2

Count value

Up/Down B individual input

Count

input 1

Count

input 2

Count value

H7CN

Dimensions

■Accessories

Adapter for Flush Mounting

Y90F-30

Panel Cutout

The standard panel cutout is as shown below. (Panel cutout

conforms to DIN43700.)

Panel cutout for side-by-side mounting of two or more Units

When mounting n Counters in a line, dimension A can be calculated

from following formula.

A = (48n-2.5)

Connecting Sockets

H7CN

H7CN-@@NM

48 72.5

(10.9) 14.2

97.6

@44.8

Panel

P3G-08

Y92F-30 Flush

Mounting Adapter

Back

Connecting

Socket

Radius:

0.5 max.

H7CN

P2CF-08(-E)

103.7

Front Mounting

H7CN +

Adapter

Y92F-30

P3G-08

95.1

Flush Mounting

Front Mounting

P2CF-11(-E)

H7CN

114.6

116.9

H7CN +

Adapter

Y92F-30

P3GA-11

Flush Mounting

H7CN

■Protective Cover

The Protective Cover shields the front panel, particularly the count

value setting section from dust, dirt and water, and prevent

malfunctioning of the Counter due to static electricity.

Note: 1. The Hard Protective Cover prevents the set count value

from being altered due to accidental contact with the push-

type thumbwheel switch.

2. The Soft Protective Cover allows the set value to be set by

depressing the thumbwheel switches through it.

It may be, however, difficult to make setting changes of the

Counter with the Y92A-48B Protective Cover attached,

which must be taken into consideration before using the

Y92A-48B Protective Cover.

Installation

■Terminal Arrangement

Connections

■Power Supply Connection

Note: 1. Make sure that the fluctuation of the supply voltage is within the permissible range.

2. Pay attention to the polarity of the DC power supply and do not make a wiring mistake.

Y92A-48B (Hard cover)

(see note 1)

Y92A-48D (Soft cover)

(see note 2)

Presetting Model

(with No Backup Function)

Presetting Model

(with Backup Function)

Totalizing Model

(with No Backup Function)

Reset input

CP1 input

CP2 input

Output circuit

Power

input

Common of

CP1 and CP2

reset inputs

Reset input

CP1 input

CP2 input

Power

input

Common of

CP1 and CP2

reset inputs

Reset input

CP1 input

CP2 input

Power

input

Common of

CP1 and CP2

reset inputs

Note: 1. Terminal 2 is a negative terminal

and terminal 7 is a positive

terminal if DC power is supplied.

2. Common terminal 1 is internally

connected to terminal 2 if the Counter

is a model that operates with DC.

Note: 1. Terminal 2 is a negative terminal

and terminal 7 is a positive

terminal if DC power is supplied.

2. Common terminal 1 is internally

connected to terminal 2 if the Counter

is a model that operates with DC.

For Models with No Backup Function For Models with

Backup Function

AC Power Supply DC Power Supply

100 to 240 VAC 12 to 48 VDC 100 to 240 VAC

H7CN

■Input Connection

The CP1 and CP2 reset inputs of the H7CN will be active when input to the H7CN is short-circuited.

■Output (Load) Connection

Delay Time

The delay time, which is the period between the moment a pulse

input signal that coincides with the preset value is ON and the

moment the corresponding control output signal is ON, varies with

the counting speed and type of output as shown in the following

table.

Transistor Input (NPN) Contact Input

Sensor

CP1 (N)

CP2 (N)

(Reset)

Input common

*Operate with transistor ON

Sensor

CP1 (N)

CP2 (N)

(Reset)

Input common

*Operate with transistor ON

CP1 (N)

CP2 (N)

(Reset)

Input common

*Operate with contact ON

(30 V max.)

* Refer to the following for the signal

levels of the transistor input.

* Sensors with voltage output can be

connected to the H7CN as shown in

the above circuit diagram. When

transistor is OFF, make sure that the

voltage between the input common

and CP1 or CP2 terminals are 4 V

min. for AC models and 6 V min. for

DC models.

Note: 1. H level with transistor

ON.Residual voltage: 2 V

max.ON impedance: 1 kΩ max.

2. L level with transistor OFF.OFF

impedance: 100 kΩ min.

* Make sure that the contact can switch

0.5 mA at 5 V with ease.

Control output Max. counting speed Delay time

Contact output 30 Hz (cps) 12.5 to 15.0 ms

5 kHz (cps) 4.0 to 5.5 ms

Transistor output 5 kHz (cps) 0.05 to 0.25 ms

Contact Output

Transistor Output

Load

*Diode to absorb counter-electromotive force

250 VAC max.

Load

30 VDC max.

H7CN

Safety Precautions

●

Be sure to read the precautions for all Counters in the website at: http://www.ia.omron.com/.

Warning Indications

Meaning of Product Safety Symbols

!CAUTION

•Make sure the proper product is specified for the application.

•For correct use, do not subject the product to the following

conditions.

•Dramatic temperature fluctuations

•High humidity or where condensation may occur

•Severe vibration and shock

•Where excessive dust, corrosive gas, or direct sunlight may be

present

•This product is not waterproof or oil resistance. Do not use the

product in any of the places subject to splashing liquid or oil

atmosphere.

•Use and store the product within the rated ranges given for the

product model you are using. If necessary, use forced cooling.

If the product is stored below −10°C, allow it to warm up for three

hours at room temperature before turning ON the power supply.

•Do not cover the vent holes on the products and the area around

the product in order to ensure thermal dissipation.

•Wiring all terminals correctly.

•Do not wire the terminals which are not used.

•Use specified size crimped terminals (M3.5, thickness 7.2mm

max.) for wiring with a gage of AWG 24 to AWG 18 (equal to a

cross section area of 0.205 to 0.823mm2).

(The wiring stripping length is 5 to 6mm.)

Up to two wires of same size and type, or two crimped terminals

can be inserted into a single terminal.

•Use this product within the rated power supply voltage and control

output.

•Use a switch, relay, or other contact to turn the power supply ON

instantaneously. If the voltage is applied gradually, the power may

not be reset or output malfunctions may occur.

•Do not apply the supply voltage directly from external to transistor

output.

•Interlock the power to the product with a relay so that the product

will not be left in an output on condition for long periods. Leaving

the product in an output-on condition for a month or longer,

especially in places with high temperatures, may result in

deterioration to internal parts, such as an electrolytic capacitor.

•A constant reading system is used in the present counter, so

settings can be changed while power is being supplied, but the

output will turn ON if the set value is set to the current

measurement value.

•When changing the set count while power is being supplied, an

inadequate push of the thumb wheel switches will display two

numbers in one display window, causing the operating count to drift

widely. Therefore, press the thumb wheel switches surely.

•Internal circuit voltage (5 V) is output to the no-

voltage input terminals, which may cause some

connected devices to malfunction or fail. Check the

specifications of the input device (e.g., rated output

voltage or whether a power supply circuit diode is

built in).

To prevent power supply devices from being subjected to charging

accidents, connect a diode as in the diagram figure when using a

power supply voltage of 5 V or less to operate input devices that do

not have a diode built into the power supply circuit.

•Check that the LED indicators are operating normally. Depending

on the operating environment, the indicators and plastic parts may

deteriorate faster than expected, causing the indicators to fail.

Periodically perform inspections and replacements.

•Use tools when separating parts for disposal.

•When disposing of the product, observer all local ordinances as

they apply.

CAUTION

Indicates a potentially hazardous

situation which, if not avoided, may

result in minor or moderate injury or in

property damage.

Precautions for

Safe Use

Supplementary comments on what to

do or avoid doing, to use the product

safely.

Precautions for

Correct Use

Supplementary comments on what to

do or avoid doing, to prevent failure to

operate, malfunction or undesirable

effect on product performance.

Used to warn of the risk of electric shock under

specific conditions.

Used for general prohibitions for which there is no

specific symbol.

Used for general mandatory action precautions

for which there is no specified symbol.

Do not touch the terminals while power is being supplied.

Doing so may occasionally result in minor injury due to

electric shock.

Do not use the product where subject to flammable or

explosive gas. Otherwise, minor injury from explosion

may occasionally occur.

Never disassemble, modify or repair the product or touch

any of the internal parts. Minor electric shock, fire, or

malfunction may occasionally occur.

The life expectancy of output relays varies considerably

with the output load and switching conditions. Always

consider the application conditions and use the output

relays within their rated load and electrical life

expectancy. If the output relays are used past their life

expectancy, contact fusing or burning may occasionally

occur. Also, never exceed the rated load current. When

using a heater, surely use a thermo switch in the load

circuit.

Tighten the screws to between 0.74 and 0.90 N⋅m. Loose

screws may occasionally result in fire.

Do not allow pieces of metal, wire clippings, or fine

metallic shavings from installation to enter the product.

Doing so may occasionally result in electric shock, fire, or

malfunction.

Precautions for Safe Use

Sensor

Input

H7CN

•Inrush current will be carried when turning on the power. If the

capacity of the power for the product is insufficient, the product

cannot start. Use a power supply, breakers, contacts which

sufficient capacity.

100 to 240 VAC specifications Approx. 0.8 A for 264 VAC

12 to 48 VDC specifications Approx. 0.4 A for 52.8 VDC

•Since 50 ms after the power is turned ON is required as the raise

time of the internal circuit voltage, note that the product may not

operate in response to any input signal during this period.

•Since 50 ms after the power is turned OFF (or momentary power

failures) is required as the fall time of the internal circuit voltage,

note that the product may respond to input signals during this

period.

•Models without power failure memory backup will operate as shown

in the following figure if the power supply is momentarily

interrupted.

Note: Use a Counter with power failure backup memory (models

ending with -M) if holding the status before the power failure is

required when the power is interrupted.

•All number display digits on the Counter will be OFF when the

signal is input for a external or manual reset. When the reset signal

is completed, the numeric display will show the reset value.

•Model H7CN 12-48 VDC specification use transformerless power

supply which the power terminals and input terminals are not

insulated. When use this specification, the internal parts of the

product may be occasionally burnt (damaged) if the wiring is not

correct. Pay attention to check the wiring before use.

Power Failure Backup Memory

•The product memorizes the status just before occurring the electric

failure memory with non-volatile memory. The rewriting lifespan of

the non-volatile memory is 1,000,000 or more. The non-volatile

memory rewrites the setting condition into the initial setting one

when the power OFF and reset input.

■Self-diagnostic Function

When an error has occurred, the bellow error codes are shown.

* Including the case when the rewriting lifespan of the nonvolatile

memory is reached.

Recovery method

As an action, turn the power OFF then back ON again. If the display

restored to normal, then a probable cause can be external noise

affecting the system. Check for external noise. In the case of e3, if

the display remains the same even when turn power ON again, input

reset. After that, if it still remains the same, the product must be

repaired.

■Changes in Specifications

Precautions for Correct Use

OFF

50 ms 50 ms

Power supply

Input can be received

Counting

operation

unstable

Input reception

Momentary

power interruption

OFF

Power supply

Operation after

power interruption

0.5 s min. Displays and outputs will be reset.

0.01 s max. The status before the power interruption

will be held.

0.01 to 0.5 s Operation will be unstable, i.e., one of the

above operations will be performed.

7 segment

display

Count UP

display

Description Output

e1 OFF CPU error OFF

e2 OFF Memory error (RAM) OFF

e3 OFF Memory error

(non-volatile memory)*

OFF

The Counter was upgraded in November 2005. The major

changes are described below.

• Backup Battery Connection to Counters with Memory

Backup

Previously, an external backup battery was required for

Counters with memory backup, but the Counter has been

upgraded so that the external battery is no longer necessary.

In the interest of product improvement, specifications are subject to change without notice.

ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.

To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.

Terms and Conditions Agreement

Read and understand this catalog.

Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you

have any questions or comments.

Warranties.

(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship

for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron

disclaims all other warranties, express or implied.

(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT

NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER

ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE

PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.

Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the

Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at

Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or

replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount

equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,

repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products

were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate

modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall

not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or

electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,

recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above

warranty.

See http://www.omron.com/global/ or contact your Omron representative for published information.

Limitation on Liability; Etc.

OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,

LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,

WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.

Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.

Suitability of Use.

Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the

combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable

third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself

is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,

system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product

with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.

NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE

QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,

AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE

OVERALL EQUIPMENT OR SYSTEM.

Programmable Products.

Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence

thereof.

Performance Data.

Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining

suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate

it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.

Change in Specifications.

Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our

practice to change part numbers when published ratings or features are changed, or when significant construction changes are

made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers

may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at

any time to confirm actual specifications of purchased Product.

Errors and Omissions.

Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is

assumed for clerical, typographical or proofreading errors or omissions.

2014.4

In the interest of product improvement, specifications are subject to change without notice.

OMRON Corporation

Industrial Automation Company

http://www.ia.omron.com/

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Omron:

H7CN-YLNM AC100-240 H7CN-XHN-AC100-240 H7CN-BLN-AC100-240 H7CN-XLN-AC100-240 H7CN-TXL AC

H7CN-XHNS AC100-240 H7CN-XLNM AC100-240 H7CN-XLNM DC24 H7CN-YLN AC100-240 H7CN-XHN DC12-48

H7CN-YLNM-AC H7CN-BLN-AC H7CN-XHN-AC