RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI
IDT Zero-DistortionTM Mixer 1 Rev2, November 07, 2016
DATASHEET
GENERAL DESCRIPTION
This document describes the specifications for the
IDTF1162 Zero-DistortionTM RF to IF Downconverting
Mixer. This device is part of a series of mixers offered
with high side or low side injection options for all UTRA
bands. See the Part# Matrix for the details of all devices
in this series.
The F1162 dual channel device is designed to operate
with a single 5V supply. It is optimized for operation in
a Multi-mode, Multi-carrier BaseStation Receiver for RF
bands from 2300 - 2700 MHz with Low Side or High
Side Injection. IF frequencies from 50 to 500 MHz are
supported. Nominally, the device offers +43 dBm
Output IP3 with 330 mA of ICC. Alternately one can
adjust 4 resistor values and a toggle pin to run the
device in low current mode with +38 dBm Output IP3
and 230 mA of ICC.
COMPETITIVE ADVANTAGE
In typical basestation receivers the RF to IF mixer
dominates the linearity performance for the entire
receive system. The Zero-DistortionTM family of mixers
dramatically improve the maximum signal levels (IM3
tones) that the BTS can withstand at a desired Signal to
Noise Ratio (SNR.) Alternately, one can run the device
in Low Current Mode to reduce Power consumption
significantly. Zero-DistortionTM technology allows
realization of either benefit.
IP3O: 11 dB STD
Mode, 5 dB LC Mode
Dissipation: 40% LC,
15% STD Mode
Allows for higher RF gain improving Sensitivity
PART# MATRIX
Part#
RF freq
range
UTRA bands
IF freq
range
Typ.
Gain
Injection
F1100
698 - 915
5,6,8,12,13,14,17
,19,20
50 - 450
8.5
High Side
F1102
698 - 915
5,6,8,12,13,14,17
,19,20
50 - 250
8.5
Both
F1150
1700 - 2200
1,2,3,4,9,10, 33,
34,35, 36, 37,39
50 - 450
8.5
High Side
F1152
1400 - 2200
1,2,3,4,9,10,111,
211, 241, 33,
34,35, 36, 37,39
50 - 350
8.5
Low Side
F
F1
11
16
62
2
2
23
30
00
0
–
–
2
27
70
00
0
7
7,
,3
38
8,
,4
40
0,
,4
41
1
5
50
0
–
–
5
50
00
0
8
8.
.9
9
B
Bo
ot
th
h
FEATURES
Dual Path for Diversity Systems
Ideal for Multi-Carrier Systems
8.9 dB Gain
Ultra linear
Low NF < 10 dB
200 Ω output impedance
Ultra high +13 dBm P1dBI
w/existing solutions
6x6 36 pin package
< 200 nsec settling from Power Down
Low Current Mode :
Standard Mode: ICC = 330 mA
NOTE production BOM on p. 25
DEVICE BLOCK DIAGRAM
ORDERING INFORMATION
1 – with High side injection
RFIN_A
IFOUT_A
RF VCO
LOISET
LCMODE
RFIN_B
IFOUT_B
Bias
Control
STBY
2
IDTF1162NBGI8
0.8 mm height
package
Green
Industrial
Temp range
Tape &
Reel
Omit IDT
prefix
RF product Line
RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI
IDT Zero-DistortionTM Mixer 2 Rev2, November 07, 2016
DATASHEET
ABSOLUTE MAXIMUM RATINGS
VCC to GND -0.3V to +5.5V
STBY, LCMODE -0.3V to (VCC_ + 0.3V)
IF_A+, IF_B+, IF_A-, IF_B-, LO1_ADJ, LO2_ADJ -0.3V to (VCC_ + 0.3V)
LO_IN, LO_IN_ALT, RF_A, RF_B -0.3V to +0.3V
IF_BiasA, IF_BiasB to GND -0.3V to +0.3V
RF Input Power (RF_IN[A+, A-, B+, B-]) +20dBm
Continuous Power Dissipation 2.2W
θJA (Junction – Ambient) +35°C/W
θJC (Junction – Case) The Case is defined as the exposed paddle +2.5°C/W
Operating Temperature Range (Case Temperature) TC = -40°C to +100°C
Maximum Junction Temperature 150°C
Storage Temperature Range -65°C to +150°C
Lead Temperature (soldering, 10s) . +260°C
Stresses above those listed above may cause permanent damage to the device. Functional operation of the
device at these or any other conditions above those indicated in the operational section of this specification is
not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI
IDT Zero-DistortionTM Mixer 3 Rev2, November 07, 2016
DATASHEET
IDTF1162 SPECIFICATION
Specifications apply at VCC = +5.00V, TC = +25°C FRF = 2600 MHz, FIF = 400MHz, Low Side Injection, PLO = 0 dBm, STBY = GND, LCMODE
= VIH (STD Mode), EVKit BOM = Standard Mode, Transformer Loss included (not de-embedded) unless otherwise noted.
Parameter
Comment
Symbol
min
typ
max
units
Logic Input High
For Standby, LCMODE
Pins
VIH
2
V
Logic Input Low
For Standby, LCMODE
Pins
VIL
0.8
V
Logic Current
For Standby Pin
IIH, IIL
-30
+30
μA
Logic Current
For LCMODE Pin
IIH, IIL
-100
-20
μA
Supply Voltage(s)
All VCC pins
VCC
4.75 to
5.25
V
Operating
Temperature Range
Case Temperature
TCASE
-40 to
+100
degC
Supply Current
Total VCC , STD Mode
Total Both Channels
ISTD
330
375
1
mA
Supply Current
Total VCC , LC Mode
LCMODE = GND
EVkit BOM = LC Mode
Total Both Channels
ILC
230
260
mA
Supply Current
Standby Mode
STBY = VIH
LCMODE > VIH (STD Mode)
Total Both Channels
ISTBY
23
30
mA
RF Freq Range
Operating Range
FRF
2300 to
2700
MHz
IF Freq Range
Operating Range
FIF
50 to 500
MHz
LO Freq Range
Operating Range
FLO
1800 to
2900
MHz
LO Power
Operating Range
PLO
-6 to +6
dBm
RF Input Impedance
Single Ended
Return Loss ~20 dB
ZRF
50
Ω
IF Output Impedance
Differential
Return Loss ~ 15 dB
ZIF
200
Ω
LO port Impedance
Single Ended
Return Loss ~15 dB
ZLO
50
Ω
Settling Time
Pin = -13 dBm
Gate STBY from VIH to VIL
Time for IF Signal to settle to
within 0.1 dB of final value
TSETT
0.150
sec
Gain STD Mode
Conversion Gain
FRF = 2300 MHz
LCMODE = VIH
EVkit BOM = STD Mode
FIF = 400 MHz (Low Side Inj.)
GSTD
7.2
8.4
9.6
dB
RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI
IDT Zero-DistortionTM Mixer 4 Rev2, November 07, 2016
DATASHEET
IDTF1162 SPECIFICATION (CONTINUED)
Parameter
Comment
Symbol
min
typ
max
units
Gain LC Mode
Conversion Gain
FRF = 2700 MHz
LCMODE = GND
EVkit BOM = LC Mode
FIF = 200 MHz (High Side Inj.)
GLC
6.8
7.9
9.0
dB
NF STD Mode
Noise Figure
RF trace de-embedded
FIF = 200 MHz
NFSTD
9.9
dB
NF LC Mode
Noise Figure
RF trace de-embedded
LCMODE = GND, EVKit BOM = LC
FIF = 200 MHz
NFLC
9.7
dB
NF w/Blocker
+100 MHz offset blocker
PBLOCKER = +10 dBm
FIF = 250 MHz
NFBLK
23.5
dB
Output IP3 – STD mode
PIN = -10 dBm per tone
800 KHz Tone Separation
IP3O1
382
43
dBm
Output IP3 – LC mode
PIN = -10 dBm per tone
FIF = 200 MHz (Low Side Inj.)
FRF = 2600 MHz
800 KHz Tone Separation
LCMODE = GND
EVKit BOM = LC Mode
IP3O3
33.5
37.7
dBm
Output IP3 – High Side
Injection
PIN = -10 dBm per tone
800 KHz Tone Separation
FIF = 154 MHz (High Side Inj.)
FRF = 2600 MHz
Modified LC mode BOM (p. 26)
IP3O2
43
dBm
2RF – 2LO rejection
PIN = -10 dBm
Frequency = FRF - ½ FIF
2x2
-68
dBc
1 dB Compression –
STD Mode
Input referred
400 MHz IF
P1dBI1
11
11.9
dBm
1 dB Compression – LC
Mode
LCMODE = GND
EVKit BOM = LC Mode
FIF = 200 MHz (Low Side Inj.)
P1dBI2
8
10.2
dBm
Gain Comp. w/blocker
Blocker unmodulated tone
PIN = +8 dBm, +100 MHz offset
Signal Pin Tone = -20 dBm
Measure ΔG of signal
FIF = 250 MHz
ΔGAC
0.15
dB
Channel Isolation
IF_B Pout vs. IF_A w/ RF_A input
ISOC
49
dBc
LO to IF leakage
LO Frequency = 2200 MHz
ISOLI
-32
-23
dBm
RF to IF leakage
Pin = -10 dBm
ISORI
-57
-43
dBm
LO to RF leakage
LO Frequency = 2345 MHz
Low Current Mode
ISOLR
-41
dBm
1 – Items in min/max columns in bold italics are Guaranteed by Test
2 – All other Items in min/max columns are Guaranteed by Design Characterization
RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI
IDT Zero-DistortionTM Mixer 5 Rev2, November 07, 2016
DATASHEET
TYPICAL OPERATING CONDTIONS
Unless otherwise Noted, the following Apply to the Typ Ops Graphs
800 KHz Tone Spacing
Low Side injection graphs with 200MHz & 400MHz IF (pages 6 – 14)
High Side injection graphs with 200MHz & 154MHz IF (pages 15 – 17)
Average of Channel A & Channel B
Pin = – 10 dBm per Tone
LO port = Pin 19 (Main Port)
Listed Temperatures are Case Temperature (TC = Case Temperature)
Where noted, TA or TAMB = Ambient Temperature
RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI
IDT Zero-DistortionTM Mixer 6 Rev2, November 07, 2016
DATASHEET
TYPICAL OPERATING CONDITIONS [IF = 200 MHz, Low Side Injection] (-1-)
Gain vs. TCASE
Gain vs. LO Level
Output IP3 vs. VCC
Gain vs. VCC
Output IP3 vs. TCASE
Output IP3 vs. LO Level
4
5
6
7
8
9
10
11
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
Gain (dB)
RF Freq (Hz)
-40 degC - 0 dBm - 5.00 V - STD
-40 degC - 0 dBm - 5.00 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
100 degC - 0 dBm - 5.00 V - STD
100 degC - 0 dBm - 5.00 V - LC
4
5
6
7
8
9
10
11
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
Gain (dB)
RF Freq (Hz)
25 degC - 6 dBm - 5.00 V - STD
25 degC - 6 dBm - 5.00 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
25 degC - -3 dBm - 5.00 V - STD
25 degC - -3 dBm - 5.00 V - LC
20
25
30
35
40
45
50
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
Output IP3 (dBm)
RF Freq (Hz)
25 degC - 0 dBm - 5.25 V - STD
25 degC - 0 dBm - 5.25 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
25 degC - 0 dBm - 4.75 V - STD
25 degC - 0 dBm - 4.75 V - LC
4
5
6
7
8
9
10
11
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
Gain (dB)
RF Freq (Hz)
25 degC - 0 dBm - 5.25 V - STD
25 degC - 0 dBm - 5.25 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
25 degC - 0 dBm - 4.75 V - STD
25 degC - 0 dBm - 4.75 V - LC
20
25
30
35
40
45
50
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
Output IP3 (dBm)
RF Freq (Hz)
-40 degC - 0 dBm - 5.00 V - STD
-40 degC - 0 dBm - 5.00 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
100 degC - 0 dBm - 5.00 V - STD
100 degC - 0 dBm - 5.00 V - LC
20
25
30
35
40
45
50
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
Output IP3 (dBm)
RF Freq (Hz)
25 degC - 6 dBm - 5.00 V - STD
25 degC - 6 dBm - 5.00 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
25 degC - -3 dBm - 5.00 V - STD
25 degC - -3 dBm - 5.00 V - LC
RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI
IDT Zero-DistortionTM Mixer 7 Rev2, November 07, 2016
DATASHEET
TYPICAL OPERATING CONDITIONS [IF = 200 MHz, Low Side Injection] (-2-)
P1dB vs. TCASE
P1dB vs. LO Level
2RF x 2LO Rejection vs. VCC
P1dB vs. VCC
2RF x 2LO rejection vs. TCASE
2RF x 2LO Rejection vs. LO Level
6
7
8
9
10
11
12
13
14
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
Input P1dB (dBm)
RF Freq (Hz)
-40 degC - 0 dBm - 5.00 V - STD
-40 degC - 0 dBm - 5.00 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
100 degC - 0 dBm - 5.00 V - STD
100 degC - 0 dBm - 5.00 V - LC
6
7
8
9
10
11
12
13
14
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
Input P1dB (dBm)
RF Freq (Hz)
25 degC - 6 dBm - 5.00 V - STD
25 degC - 6 dBm - 5.00 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
25 degC - -3 dBm - 5.00 V - STD
25 degC - -3 dBm - 5.00 V - LC
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
2 X 2 Rejection [Pin = -10] (dBc)
RF Freq (Hz)
25 degC - 5.25 V - 0 dBm - STD
25 degC - 5.25 V - 0 dBm - LC
25 degC - 5.00 V - 0 dBm - STD
25 degC - 5.00 V - 0 dBm - LC
25 degC - 4.75 V - 0 dBm - STD
25 degC - 4.75 V - 0 dBm - LC
6
7
8
9
10
11
12
13
14
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
Input P1dB (dBm)
RF Freq (Hz)
25 degC - 0 dBm - 5.25 V - STD
25 degC - 0 dBm - 5.25 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
25 degC - 0 dBm - 4.75 V - STD
25 degC - 0 dBm - 4.75 V - LC
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
2 X 2 Rejection [Pin = -10] (dBc)
RF Freq (Hz)
-40 degC - STD - 5.00 V - 0 dBm
-40 degC - LC - 5.00 V - 0 dBm
25 degC - STD - 5.00 V - 0 dBm
25 degC - LC - 5.00 V - 0 dBm
100 degC - STD - 5.00 V - 0 dBm
100 degC - LC - 5.00 V - 0 dBm
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
2 X 2 Rejection [Pin = -10] (dBc)
RF Freq (Hz)
25 degC - 5.00 V - 6 dBm - STD
25 degC - 5.00 V - 6 dBm - LC
25 degC - 5.00 V - 0 dBm - STD
25 degC - 5.00 V - 0 dBm - LC
25 degC - 5.00 V - -3 dBm - STD
25 degC - 5.00 V - -3 dBm - LC
RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI
IDT Zero-DistortionTM Mixer 8 Rev2, November 07, 2016
DATASHEET
TYPICAL OPERATING CONDITIONS [IF = 200 MHz, Low Side Injection] (-3-)
ICC vs. TCASE
ICC vs. LO Level
LO-IF Leakage vs. VCC
ICC vs. VCC
LO-IF Leakage vs. TCASE
LO-IF Leakage vs. LO Level
0.200
0.220
0.240
0.260
0.280
0.300
0.320
0.340
0.360
0.380
0.400
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
Total ICC (Amps)
RF Freq (Hz)
-40 degC - 0 dBm - 5.00 V - STD
-40 degC - 0 dBm - 5.00 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
100 degC - 0 dBm - 5.00 V - STD
100 degC - 0 dBm - 5.00 V - LC
0.200
0.220
0.240
0.260
0.280
0.300
0.320
0.340
0.360
0.380
0.400
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
ICC (Amps)
RF Freq (Hz)
25 degC - 6 dBm - 5.00 V - STD
25 degC - 6 dBm - 5.00 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
25 degC - -3 dBm - 5.00 V - STD
25 degC - -3 dBm - 5.00 V - LC
-50
-45
-40
-35
-30
-25
-20
-15
-10
-5
0
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
LO to IF Leakage (dBm)
RF Freq (Hz)
25 degC - 0 dBm - 5.25 V - STD
25 degC - 0 dBm - 5.25 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
25 degC - 0 dBm - 4.75 V - STD
25 degC - 0 dBm - 4.75 V - LC
0.200
0.220
0.240
0.260
0.280
0.300
0.320
0.340
0.360
0.380
0.400
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
ICC (Amps)
RF Freq (Hz)
25 degC - 0 dBm - 5.25 V - STD
25 degC - 0 dBm - 5.25 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
25 degC - 0 dBm - 4.75 V - STD
25 degC - 0 dBm - 4.75 V - LC
-50
-45
-40
-35
-30
-25
-20
-15
-10
-5
0
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
LO to IF Leakage (dBm)
RF Freq (Hz)
-40 degC - 0 dBm - 5.00 V - STD
-40 degC - 0 dBm - 5.00 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
100 degC - 0 dBm - 5.00 V - STD
100 degC - 0 dBm - 5.00 V - LC
-50
-45
-40
-35
-30
-25
-20
-15
-10
-5
0
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
LO to IF Leakage (dBm)
RF Freq (Hz)
25 degC - 6 dBm - 5.00 V - STD
25 degC - 6 dBm - 5.00 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
25 degC - -3 dBm - 5.00 V - STD
25 degC - -3 dBm - 5.00 V - LC
RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI
IDT Zero-DistortionTM Mixer 9 Rev2, November 07, 2016
DATASHEET
TYPICAL OPERATING CONDITIONS [IF = 200 MHz, Low Side Injection] (-4-)
RF-IF Leakage vs. TCASE
RF-IF Leakage vs. LO Level
3RF X 3LO Rejection vs. VCC
RF-IF Leakage vs. VCC
3RF X 3LO Rejection vs. TCASE
3RF X 3LO Rejection vs. LO Level
-70
-65
-60
-55
-50
-45
-40
-35
-30
-25
-20
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
RF to IF Leakage [Pin = -10] (dBm)
RF Freq (Hz)
-40 degC - 0 dBm - 5.00 V - STD
-40 degC - 0 dBm - 5.00 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
100 degC - 0 dBm - 5.00 V - STD
100 degC - 0 dBm - 5.00 V - LC
-70
-65
-60
-55
-50
-45
-40
-35
-30
-25
-20
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
RF to IF Leakage [Pin = -10] (dBm)
RF Freq (Hz)
25 degC - 6 dBm - 5.00 V - STD
25 degC - 6 dBm - 5.00 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
25 degC - -3 dBm - 5.00 V - STD
25 degC - -3 dBm - 5.00 V - LC
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
3 x 3 Rejection [Pin =-10] (dBc)
RF Freq (Hz)
25 degC - 5.25 V - 0 dBm - STD
25 degC - 5.25 V - 0 dBm - LC
25 degC - 5.00 V - 0 dBm - STD
25 degC - 5.00 V - 0 dBm - LC
25 degC - 4.75 V - 0 dBm - STD
25 degC - 4.75 V - 0 dBm - LC
-70
-65
-60
-55
-50
-45
-40
-35
-30
-25
-20
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
RF to IF Leakage [Pin = -10] (dBm)
RF Freq (Hz)
25 degC - 0 dBm - 5.25 V - STD
25 degC - 0 dBm - 5.25 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
25 degC - 0 dBm - 4.75 V - STD
25 degC - 0 dBm - 4.75 V - LC
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
3 X 3 Rejection [Pin = -10] (dBc)
RF Freq (Hz)
-40 degC - 5.00 V - 0 dBm - STD
-40 degC - 5.00 V - 0 dBm - LC
25 degC - 5.00 V - 0 dBm - STD
25 degC - 5.00 V - 0 dBm - LC
100 degC - 5.00 V - 0 dBm - STD
100 degC - 5.00 V - 0 dBm - LC
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
3 X 3 Rejection [Pin = -10] (dBc)
RF Freq (Hz)
25 degC - 5.00 V - 6 dBm - STD
25 degC - 5.00 V - 6 dBm - LC
25 degC - 5.00 V - 0 dBm - STD
25 degC - 5.00 V - 0 dBm - LC
25 degC - 5.00 V - -3 dBm - STD
25 degC - 5.00 V - -3 dBm - LC
RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI
IDT Zero-DistortionTM Mixer 10 Rev2, November 07, 2016
DATASHEET
TYPICAL OPERATING CONDITIONS [IF = 200 MHz, Low Side Injection] (-5-)
Channel Isolation vs. TCASE
Channel Isolation vs. LO Level
Noise Figure vs. TCASE (STD Mode)
Channel Isolation vs. VCC
Noise Figure vs. TCASE (LC Mode)
NF vs. Blocker (RF =2600 MHz, IF = 250 MHz, TA = 25C)
40
45
50
55
60
65
70
75
80
85
90
2.30E+09 2.40E+09 2.50E+09 2.60E+09 2.70E+09
Channel Isolation (dBc)
RF Freq (Hz)
-40 deg C - 0 dBm - 5.00 V - STD
-40 deg C - 0 dBm - 5.00 V - LC
25 deg C - 0 dBm - 5.00 V - STD
25 deg C - 0 dBm - 5.00 V - LC
100 deg C - 0 dBm - 5.00 V - STD
100 deg C - 0 dBm - 5.00 V - LC
40
45
50
55
60
65
70
75
80
85
90
2.30E+09 2.40E+09 2.50E+09 2.60E+09 2.70E+09
Channel Isolation (dBc)
RF Freq (Hz)
-40 deg C - 0 dBm - 5.00 V - STD
-40 deg C - 0 dBm - 5.00 V - LC
25 deg C - 0 dBm - 5.00 V - STD
25 deg C - 0 dBm - 5.00 V - LC
100 deg C - 0 dBm - 5.00 V - STD
100 deg C - 0 dBm - 5.00 V - LC
7.0
8.0
9.0
10.0
11.0
12.0
13.0
14.0
2300
2400
2500
2600
2700
Noise Figure [IF = 200 MHz] (dB)
RF Frequency (MHz)
-40 degC - ChA
-40 degC - ChB
25 degC - ChA
25 degC - ChB
100 degC - ChA
100 degC - ChB
RFtrace losses de-embedded
40
45
50
55
60
65
70
75
80
85
90
2.30E+09 2.40E+09 2.50E+09 2.60E+09 2.70E+09
Channel Isolation (dBc)
RF Freq (Hz)
25 deg C - 0 dBm - 4.75 V - STD
25 deg C - 0 dBm - 4.75 V - LC
25 deg C - 0 dBm - 5.00 V - STD
25 deg C - 0 dBm - 5.00 V - LC
25 deg C - 0 dBm - 5.25 V - STD
25 deg C - 0 dBm - 5.25 V - LC
7.0
8.0
9.0
10.0
11.0
12.0
13.0
14.0
2300
2400
2500
2600
2700
Noise Figure [IF = 200 MHz] (dB)
RF Frequency (MHz)
-40 degC - ChA
-40 degC - ChB
25 degC - ChA
25 degC - ChB
100 degC - ChA
100 degC - ChB
RFtrace losses de-embedded
6
8
10
12
14
16
18
20
22
24
26
-30 -26 -22 -18 -14 -10 -6 -2 2 6 10
Noise Figure (dB)
Blocker Input Power (dBm)
ChA STD
ChB STD
ChA LC
ChB LC
RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI
IDT Zero-DistortionTM Mixer 11 Rev2, November 07, 2016
DATASHEET
TYPICAL OPERATING CONDITIONS [IF = 400 MHz, Low Side Injection] (-6-)
Gain vs. TCASE
Gain vs. LO Level
Output IP3 vs. VCC (EVKIT DE-EMBEDDED)
Gain vs. TCASE (EVKIT DE-EMBEDDED)
Output IP3 vs. TCASE (EVKIT DE-EMBEDDED)
Output IP3 vs. LO Level (EVKIT DE-EMBEDDED)
4
5
6
7
8
9
10
11
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
Gain (dB)
RF Freq (Hz)
-40 degC - 0 dBm - 5.00 V - STD
-40 degC - 0 dBm - 5.00 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
100 degC - 0 dBm - 5.00 V - STD
100 degC - 0 dBm - 5.00 V - LC
4
5
6
7
8
9
10
11
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
Gain (dB)
RF Freq (Hz)
25 degC - 6 dBm - 5.00 V - STD
25 degC - 6 dBm - 5.00 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
25 degC - -3 dBm - 5.00 V - STD
25 degC - -3 dBm - 5.00 V - LC
20
25
30
35
40
45
50
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
Output IP3 (dBm)
RF Freq (Hz)
25 degC - 0 dBm - 5.25 V - STD
25 degC - 0 dBm - 5.25 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
25 degC - 0 dBm - 4.75 V - STD
25 degC - 0 dBm - 4.75 V - LC
EVkit effects de-embedded, corrected for:
TC4-1T transformer loss (p. 19 middle right graph)
4
5
6
7
8
9
10
11
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
Gain (dB)
RF Freq (Hz)
-40 degC - 0 dBm - 5.00 V - STD
-40 degC - 0 dBm - 5.00 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
100 degC - 0 dBm - 5.00 V - STD
100 degC - 0 dBm - 5.00 V - LC
EVkit effects de-embedded, corrected for:
TC4-1T transformer loss (p. 19 middle right graph)
RF input trace loss (p. 19 middle left graph)
20
25
30
35
40
45
50
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
Output IP3 (dBm)
RF Freq (Hz)
-40 degC - 0 dBm - 5.00 V - STD
-40 degC - 0 dBm - 5.00 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
100 degC - 0 dBm - 5.00 V - STD
100 degC - 0 dBm - 5.00 V - LC
EVkit effects de-embedded, corrected for:
TC4-1T transformer loss (p. 19 middle right graph)
20
25
30
35
40
45
50
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
Output IP3 (dBm)
RF Freq (Hz)
25 degC - 6 dBm - 5.00 V - STD
25 degC - 6 dBm - 5.00 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
25 degC - -3 dBm - 5.00 V - STD
25 degC - -3 dBm - 5.00 V - LC
EVkit effects de-embedded, corrected for:
TC4-1T transformer loss (p. 19 middle right graph)
RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI
IDT Zero-DistortionTM Mixer 12 Rev2, November 07, 2016
DATASHEET
TYPICAL OPERATING CONDITIONS [IF = 400 MHz, Low Side Injection] (-7-)
P1dB vs. TCASE
P1dB vs. LO Level
2RF x 2LO Rejection vs. VCC
P1dB vs. VCC
2RF x 2LO rejection vs. TCASE
2RF x 2LO rejection vs. LO Level
6
7
8
9
10
11
12
13
14
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
Input P1dB (dBm)
RF Freq (Hz)
-40 degC - 0 dBm - 5.00 V - STD
-40 degC - 0 dBm - 5.00 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
100 degC - 0 dBm - 5.00 V - STD
100 degC - 0 dBm - 5.00 V - LC
6
7
8
9
10
11
12
13
14
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
Input P1dB (dBm)
RF Freq (Hz)
25 degC - 6 dBm - 5.00 V - STD
25 degC - 6 dBm - 5.00 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
25 degC - -3 dBm - 5.00 V - STD
25 degC - -3 dBm - 5.00 V - LC
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
2 X 2 Rejection [Pin = -10] (dBc)
RF Freq (Hz)
25 degC - 0 dBm - 5.25 V - STD
25 degC - 0 dBm - 5.25 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
25 degC - 0 dBm - 4.75 V - STD
25 degC - 0 dBm - 4.75 V - LC
6
7
8
9
10
11
12
13
14
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
Input P1dB (dBm)
RF Freq (Hz)
25 degC - 0 dBm - 5.25 V - STD
25 degC - 0 dBm - 5.25 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
25 degC - 0 dBm - 4.75 V - STD
25 degC - 0 dBm - 4.75 V - LC
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
2 X 2 Rejection [Pin = -10] (dBc)
RF Freq (Hz)
-40 degC - 0 dBm - 5.00 V - STD
-40 degC - 0 dBm - 5.00 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
100 degC - 0 dBm - 5.00 V - STD
100 degC - 0 dBm - 5.00 V - LC
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
2 X 2 Rejection [Pin = -10] (dBm)
RF Freq (Hz)
25 degC - 6 dBm - 5.00 V - STD
25 degC - 6 dBm - 5.00 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
25 degC - -3 dBm - 5.00 V - STD
25 degC - -3 dBm - 5.00 V - LC
RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI
IDT Zero-DistortionTM Mixer 13 Rev2, November 07, 2016
DATASHEET
TYPICAL OPERATING CONDITIONS [IF = 400 MHz, Low Side Injection] (-8-)
ICC vs. TCASE
ICC vs. LO Level
LO-IF Leakage vs. VCC
ICC vs. VCC
LO-IF Leakage vs. TCASE
LO-IF Leakage vs. LO Level
0.200
0.220
0.240
0.260
0.280
0.300
0.320
0.340
0.360
0.380
0.400
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
Total ICC (Amps)
RF Freq (Hz)
-40 degC - 0 dBm - 5.00 V - STD
-40 degC - 0 dBm - 5.00 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
100 degC - 0 dBm - 5.00 V - STD
100 degC - 0 dBm - 5.00 V - LC
0.200
0.220
0.240
0.260
0.280
0.300
0.320
0.340
0.360
0.380
0.400
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
ICC (Amps)
RF Freq (Hz)
25 degC - 6 dBm - 5.00 V - STD
25 degC - 6 dBm - 5.00 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
25 degC - -3 dBm - 5.00 V - STD
25 degC - -3 dBm - 5.00 V - LC
-50
-45
-40
-35
-30
-25
-20
-15
-10
-5
0
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
LO to IF Leakage (dBm)
RF Freq (Hz)
25 degC - 0 dBm - 5.25 V - STD
25 degC - 0 dBm - 5.25 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
25 degC - 0 dBm - 4.75 V - STD
25 degC - 0 dBm - 4.75 V - LC
0.200
0.220
0.240
0.260
0.280
0.300
0.320
0.340
0.360
0.380
0.400
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
ICC (Amps)
RF Freq (Hz)
25 degC - 0 dBm - 5.25 V - STD
25 degC - 0 dBm - 5.25 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
25 degC - 0 dBm - 4.75 V - STD
25 degC - 0 dBm - 4.75 V - LC
-50
-45
-40
-35
-30
-25
-20
-15
-10
-5
0
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
LO to IF Leakage (dBm)
RF Freq (Hz)
-40 degC - 0 dBm - 5.00 V - STD
-40 degC - 0 dBm - 5.00 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
100 degC - 0 dBm - 5.00 V - STD
100 degC - 0 dBm - 5.00 V - LC
-50
-45
-40
-35
-30
-25
-20
-15
-10
-5
0
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
LO to IF Leakage (dBm)
RF Freq (Hz)
25 degC - 6 dBm - 5.00 V - STD
25 degC - 6 dBm - 5.00 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
25 degC - -3 dBm - 5.00 V - STD
25 degC - -3 dBm - 5.00 V - LC
RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI
IDT Zero-DistortionTM Mixer 14 Rev2, November 07, 2016
DATASHEET
TYPICAL OPERATING CONDITIONS [IF = 400 MHz, Low Side Injection] (-9-)
RF-IF Leakage vs. TCASE
RF-IF Leakage vs. LO Level
3RF X 3LO Rejection vs. VCC
RF-IF Leakage vs. VCC
3RF X 3LO Rejection vs. TCASE
3RF X 3LO Rejection vs. LO Level
-70
-65
-60
-55
-50
-45
-40
-35
-30
-25
-20
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
RF to IF Leakage [Pin = -10] (dBm)
RF Freq (Hz)
-40 degC - 0 dBm - 5.00 V - STD
-40 degC - 0 dBm - 5.00 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
100 degC - 0 dBm - 5.00 V - STD
100 degC - 0 dBm - 5.00 V - LC
-70
-65
-60
-55
-50
-45
-40
-35
-30
-25
-20
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
RF to IF Leakage [Pin = -10] (dBm)
RF Freq (Hz)
25 degC - 6 dBm - 5.00 V - STD
25 degC - 6 dBm - 5.00 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
25 degC - -3 dBm - 5.00 V - STD
25 degC - -3 dBm - 5.00 V - LC
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
3 X 3 Rejection [Pin = -10] (dBc)
RF Freq (Hz)
25 degC - 0 dBm - 5.25 V - STD
25 degC - 0 dBm - 5.25 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
25 degC - 0 dBm - 4.75 V - STD
25 degC - 0 dBm - 4.75 V - LC
-70
-65
-60
-55
-50
-45
-40
-35
-30
-25
-20
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
RF to IF Leakage [Pin = -10] (dBm)
RF Freq (Hz)
25 degC - 0 dBm - 5.25 V - STD
25 degC - 0 dBm - 5.25 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
25 degC - 0 dBm - 4.75 V - STD
25 degC - 0 dBm - 4.75 V - LC
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
3 X 3 Rejection [Pin = -10] (dBc)
RF Freq (Hz)
-40 degC - 0 dBm - 5.00 V - STD
-40 degC - 0 dBm - 5.00 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
100 degC - 0 dBm - 5.00 V - STD
100 degC - 0 dBm - 5.00 V - LC
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
3 X 3 Rejection [Pin = -10] (dBc)
RF Freq (Hz)
25 degC - 6 dBm - 5.00 V - STD
25 degC - 6 dBm - 5.00 V - LC
25 degC - 0 dBm - 5.00 V - STD
25 degC - 0 dBm - 5.00 V - LC
25 degC - -3 dBm - 5.00 V - STD
25 degC - -3 dBm - 5.00 V - LC
RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI
IDT Zero-DistortionTM Mixer 15 Rev2, November 07, 2016
DATASHEET
TYPICAL OPERATING CONDITIONS [High Side Injection
see LC mode modifications on p. 25
] (-10-)
Gain vs. TCASE (EVKIT DE-EMBEDDED)
Output IP3 vs. TCASE
P1dB vs. TCASE
Gain vs. LO Level (EVKit de-embedded)
Output IP3 vs. LO Level
P1dB vs. LO Level
5
6
7
8
9
10
11
12
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
Gain (dB)
RF Freq (Hz)
-40 degC -0 dBm - STD - 2.0E+8Hz IF
-40 degC -0 dBm - LC (mod) - 1.5E+8Hz IF
25 degC - 0 dBm - STD - 2.0E+8Hz IF
25 degC - 0 dBm -LC (mod) - 1.5E+8Hz IF
100 degC -0 dBm - STD - 2.0E+8Hz IF
100 degC -0 dBm - LC (mod) - 1.5E+8Hz IF
EVkit effects de-embedded, corrected for:
RF input Trace loss (p. 19 middle left graph)
TC4-1T transformer loss (p. 19 middle right graph)
20
25
30
35
40
45
50
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
Output IP3 (dBm)
RF Freq (Hz)
-40 degC - 0 dBm - STD - 2.0E+8Hz IF
-40 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF
25 degC - 0 dBm - STD - 2.0E+8Hz IF
25 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF
100 degC - 0 dBm - STD - 2.0E+8Hz IF
100 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF
6
7
8
9
10
11
12
13
14
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
Input P1dB (dBm)
RF Freq (Hz)
-40 degC - 0 dBm - STD - 2.0E+8Hz IF
-40 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF
25 degC - 0 dBm - STD - 2.0E+8Hz IF
25 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF
100 degC - 0 dBm - STD - 2.0E+8Hz IF
100 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF
5
6
7
8
9
10
11
12
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
Gain (dB)
RF Freq (Hz)
25 degC - 6 dBm - STD - 2.0E+8Hz IF
25 degC - 6 dBm -LC (mod) - 1.5E+8Hz IF
25 degC - 0 dBm - STD - 2.0E+8Hz IF
25 degC - 0 dBm -LC (mod) - 1.5E+8Hz IF
25 degC - -3 dBm - STD - 2.0E+8Hz IF
25 degC - -3 dBm - LC (mod) - 1.5E+8Hz IF
EVkit effects de-embedded, corrected for:
RF input Trace loss (p. 19 middle left graph)
TC4-1T transformer loss (p. 19 middle right graph)
20
25
30
35
40
45
50
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
Output IP3 (dBm)
RF Freq (Hz)
25 degC - 6 dBm - STD - 2.0E+8Hz IF
25 degC - 6 dBm - LC (mod) - 1.5E+8Hz IF
25 degC - 0 dBm - STD - 2.0E+8Hz IF
25 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF
25 degC - -3 dBm - STD - 2.0E+8Hz IF
25 degC - -3 dBm - LC (mod) - 1.5E+8Hz IF
6
7
8
9
10
11
12
13
14
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
Input P1dB (dBm)
RF Freq (Hz)
25 degC - 6 dBm - STD - 2.0E+8Hz IF
25 degC - 6 dBm - LC (mod) - 1.5E+8Hz IF
25 degC - 0 dBm - STD - 2.0E+8Hz IF
25 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF
25 degC - -3 dBm - STD - 2.0E+8Hz IF
25 degC - -3 dBm - LC (mod) - 1.5E+8Hz IF
RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI
IDT Zero-DistortionTM Mixer 16 Rev2, November 07, 2016
DATASHEET
TYPICAL OPERATING CONDITIONS [High Side Injection
see LC mode modifications on p. 25
] (-11-)
2RF x 2LO vs. TCASE [IF = 154 MHz]
ICC vs. TCASE
LO to IF Leakage vs. TCASE
2RF x 2LO vs. LO Level [IF = 154 MHz]
ICC vs. LO Level
LO to IF Leakage vs. LO Level
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
2 X 2 Rejection [Pin = -10 dBm] (dBc)
RF Freq (Hz)
-40 degC - 5.00 V - 0 dBm - STD
-40 degC - 5.00 V - 0 dBm - LC (mod)
25 degC - 5.00 V - 0 dBm - STD
25 degC - 5.00 V - 0 dBm - LC (mod)
100 degC - 5.00 V - 0 dBm - STD
100 degC - 5.00 V - 0 dBm - LC (mod)
0.200
0.220
0.240
0.260
0.280
0.300
0.320
0.340
0.360
0.380
0.400
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
ICC (Amps)
RF Freq (Hz)
-40 degC - 0 dBm - STD - 2.0E+8Hz IF
-40 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF
25 degC - 0 dBm - STD - 2.0E+8Hz IF
25 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF
100 degC - 0 dBm - STD - 2.0E+8Hz IF
100 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF
-50
-45
-40
-35
-30
-25
-20
-15
-10
-5
0
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
LO to IF Leakage (dBm)
RF Freq (Hz)
-40 degC - 0 dBm - STD - 2.0E+8Hz IF
-40 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF
25 degC - 0 dBm - STD - 2.0E+8Hz IF
25 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF
100 degC - 0 dBm - STD - 2.0E+8Hz IF
100 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
2 X 2 Rejection [Pin = -10 dBm] (dBc)
RF Freq (Hz)
25 degC - 5.00 V - 6 dBm - STD
25 degC - 5.00 V - 6 dBm - LC (mod)
25 degC - 5.00 V - 0 dBm - STD
25 degC - 5.00 V - 0 dBm - LC (mod)
25 degC - 5.00 V - -3 dBm - STD
25 degC - 5.00 V - -3 dBm - LC (mod)
0.200
0.220
0.240
0.260
0.280
0.300
0.320
0.340
0.360
0.380
0.400
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
ICC (Amps)
RF Freq (Hz)
25 degC - 6 dBm - STD - 2.0E+8Hz IF
25 degC - 6 dBm - LC (mod) - 1.5E+8Hz IF
25 degC - 0 dBm - STD - 2.0E+8Hz IF
25 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF
25 degC - -3 dBm - STD - 2.0E+8Hz IF
25 degC - -3 dBm - LC (mod) - 1.5E+8Hz IF
-50
-45
-40
-35
-30
-25
-20
-15
-10
-5
0
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
LO to IF Leakage (dBm)
RF Freq (Hz)
25 degC - 6 dBm - STD - 2.0E+8Hz IF
25 degC - 6 dBm -LC (mod) - 1.5E+8Hz IF
25 degC - 0 dBm - STD - 2.0E+8Hz IF
25 degC - 0 dBm -LC (mod) - 1.5E+8Hz IF
25 degC - -3 dBm - STD - 2.0E+8Hz IF
25 degC - -3 dBm - LC (mod) - 1.5E+8Hz IF
RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI
IDT Zero-DistortionTM Mixer 17 Rev2, November 07, 2016
DATASHEET
TYPICAL OPERATING CONDITIONS [High Side Injection
see LC mode modifications on p. 25
] (-12-)
RF to IF Leakage vs. TCASE
3RF x 3LO rejection vs. TCASE [IF = 154 MHz]
RF to IF Leakage vs. LO Level
3RF x 3LO rejection vs. LO Level [IF = 154 MHz]
-70
-65
-60
-55
-50
-45
-40
-35
-30
-25
-20
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
RF to IF Leakage [Pin = -10] (dBm)
RF Freq (Hz)
-40 degC -0 dBm - STD - 2.0E+8Hz IF
-40 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF
25 degC - 0 dBm - STD - 2.0E+8Hz IF
25 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF
100 degC -0 dBm - STD - 2.0E+8Hz IF
100 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
3 X 3 Rejection [Pin = -10] (dBc)
RF Freq (Hz)
-40 degC - 5.00 V - 0 dBm - STD
-40 degC - 5.00 V - 0 dBm - LC (mod)
25 degC - 5.00 V - 0 dBm - STD
25 degC - 5.00 V - 0 dBm - LC (mod)
100 degC - 5.00 V - 0 dBm - STD
100 degC - 5.00 V - 0 dBm - LC (mod)
-70
-65
-60
-55
-50
-45
-40
-35
-30
-25
-20
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
RF to IF Leakage [Pin = -10] (dBm)
RF Freq (Hz)
25 degC - 6 dBm - STD - 2.0E+8Hz IF
25 degC - 6 dBm - LC (mod) - 1.5E+8Hz IF
25 degC - 0 dBm - STD - 2.0E+8Hz IF
25 degC - 0 dBm - LC (mod) - 1.5E+8Hz IF
25 degC - -3 dBm - STD - 2.0E+8Hz IF
25 degC - -3 dBm - LC (mod) - 1.5E+8Hz IF
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
2.30E+09
2.40E+09
2.50E+09
2.60E+09
2.70E+09
3 X 3 Rejection [Pin = -10] (dBc)
RF Freq (Hz)
25 degC - 5.00 V - 6 dBm - STD
25 degC - 5.00 V - 6 dBm - LC (mod)
25 degC - 5.00 V - 0 dBm - STD
25 degC - 5.00 V - 0 dBm - LC (mod)
25 degC - 5.00 V - -3 dBm - STD
25 degC - 5.00 V - -3 dBm - LC (mod)
RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI
IDT Zero-DistortionTM Mixer 18 Rev2, November 07, 2016
DATASHEET
TYPICAL OPERATING CONDITIONS [General] (-13-)
EVkit IF Port Match (TA = 25C)
Settling Time (STBY -> VIL)
Main LO Port Match (TA = 25C, PMEAS = 0 dBm)
Alt. LO port Match (TA = 25C, PMEAS = 0 dBm)
Settling Time (STBY -> VIH)
EVkit RF Port Match (TA = 25C)
-30
-25
-20
-15
-10
-5
0
50
100
150
200
250
300
350
400
450
500
550
IF Return Loss (dB)
IF Frequency (MHz)
Average of ChA STD Mode
Average of ChA LC Mode
Average of ChB STD Mode
Average of ChB LC Mode
0
2
4
6
8
10
-0.5
-0.3
-0.1
0.1
0.3
0.5
-40 040 80 120 160 200
STBY Logic Pin (Volts)
Vif Out (Volts)
Time (nsec)
Vif
Vstby
Turn On Settling Time: 150 nsec
-30
-25
-20
-15
-10
-5
0
1.8
1.9
2.0
2.2
2.3
2.4
2.5
2.6
2.8
2.9
3.0
LO port Return Loss (dB)
LO Freq (GHz)
STD Mode ON
STD Mode STBY
LC Mode ON
LC Mode STBY
For Main LO port connector (Pin 19)
-30
-25
-20
-15
-10
-5
0
1.8E+09 2E+09 2.2E+09 2.4E+09 2.6E+09 2.8E+09 3E+09
Alt LO Port Return Loss (dB)
LO Frequency (Hz)
LC Mode: LO Power = 0 dBm
Connector for Pin 27
0
2
4
6
8
10
-0.5
-0.3
-0.1
0.1
0.3
0.5
-40 040 80 120 160 200
STBY Logic Pin (V)
Vif Out (Volts)
Time (nsec)
Vif
Vstby
Turn Off Settling Time: 70 nsec
-50
-45
-40
-35
-30
-25
-20
-15
-10
-5
0
2.20
2.30
2.40
2.50
2.60
2.70
2.80
2.90
3.00
RF Port Return Loss (dB)
RF Freq (GHz)
Average of ChA STD Mode
Average of ChA LC Mode
Average of ChB STD Mode
Average of ChB LC Mode
LO = 2.2 GHz / 0 dBm
RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI
IDT Zero-DistortionTM Mixer 19 Rev2, November 07, 2016
DATASHEET
TYPICAL OPERATING CONDITIONS [General] (-14-)
IP3O vs. f (TA = 25C, Freq = 2.6 GHz, IF = 200 MHz)
EVkit Input RF Trace Loss (TA = 25C)
IP3O Distribution (FIF = 200MHz, LC mode, N = 3340)
IP3O vs. PIN (TA = 25C, Freq = 2.6 GHz, IF = 200 MHz)
TC4-1T Transformer Loss
Gain Distribution (FIF = 400MHz, STD mode, N = 3340)
20
25
30
35
40
45
50
8.00E+05
5.80E+06
1.08E+07
1.58E+07
2.08E+07
2.58E+07
3.08E+07
Output IP3 (dBm)
Tone Separation (Hz)
STD
LC
-0.7
-0.6
-0.5
-0.4
-0.3
-0.2
-0.1
0.0
2300
2400
2500
2600
2700
EVkit RF_A & RF_B Trace Loss (dB)
RF Frequency (MHz)
-40 degC
25 degC
100 degC
See Noise Figure Plots. This is used to
de-embed RAW EVkit measurements
0%
5%
10%
15%
20%
25%
30%
35%
Percentage
IP3O Bin (dBm)
Channel B
Channel A
20
25
30
35
40
45
50
-14
-13
-12
-11
-10
-9
-8
-7
-6
-5
-4
-3
-2
Output IP3 (dBm)
Input Power (dBm/Tone)
STD
LC
-1.4
-1.2
-1.0
-0.8
-0.6
-0.4
-0.2
0.0
4.0E+07 8.0E+07 1.2E+08 1.6E+08 2.0E+08 2.4E+08 2.8E+08 3.2E+08 3.6E+08 4.0E+08
TC4-1T Transformer Loss (dB)
Frequency (Hz)
-40C
+25C
+100C
See Mixer Device Gain plots. This Data is
used to de-embed the EVKit measured data
0%
5%
10%
15%
20%
25%
30%
35%
Percentage
Gain Bin (dB)
Channel B
Channel A
RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI
IDT Zero-DistortionTM Mixer 20 Rev2, November 07, 2016
DATASHEET
PACKAGE DRAWING (6X6 QFN)
RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI
IDT Zero-DistortionTM Mixer 21 Rev2, November 07, 2016
DATASHEET
PINOUTS
36 35 34 33 32 31 30 29 28
9
RF_B
8
7
6
NC [internal NC]
5
4
NC [internal NC]
3
GND [DB GND]
2
GND [RFA_rtn]
1
RF_A
18
GND [DB GND]
17
LO1_ADJ
16
VCC
15
NC [internal NC]
14
IF_B-
13
IF_B+
12
NC [internal NC]
11
IF_BiasB
10
VCC
19 LO_in
20
GND [internal NC]
21 VCC
22
GND [LCMODE]
23
GND [STBY]
24
LO_SW [internal NC]
25
GND [DB GND]
26
LO_in_alt
27
B
I
A
S
C
T
R
L
GND [DB GND]
LO2_ADJ
VCC
NC [internal NC]
IF_A-
IF_A+
NC [internal NC]
IF_BiasA
VCC
GND [DB GND]
GND [DB GND]
Black Text denotes recommended external connection
Red Text denotes internal Function or Connection
- DB GND = Downbonded to Paddle
- Internal NC = Pin not connected
GND [RFB_rtn] GND [LO_rtn]
Please Note!
- Only connect to one LO feed
- Choose Either Pin 19 or Pin 27
- Do not connect the unused LO pin to
ensure good LO return loss
RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI
IDT Zero-DistortionTM Mixer 22 Rev2, November 07, 2016
DATASHEET
PIN DESCRIPTIONS
Pin
Name
Function
1
RF_A
Main Channel RF Input. Internally matched to 50Ω. DO NOT
apply DC to these pins
2, 8, 20
RF_Artn,
RF_Brtn, LO_rtn
Transformer Ground Returns. Ground these pins.
3, 5, 7, 18, 24,
28
GND
Ground these pins.
4, 6, 12, 15,
31, 23, 26, 34
N.C.
No Connection. Not internally connected. OK to connect to Vcc.
OK to connect to GND
10, 16, 21, 30,
36
VCC
Power Supply. Bypass to GND with capacitors shown in the
Typical Application Circuit as close as possible to pin.
9
RF_B
Diversity Channel RF Input. Internally matched to 50Ω
11
IF_BiasB
Connect the specified resistor from this pin to ground to set the
bias for the Diversity IF amplifier. This is NOT a current set
resistor
13, 14
IFB+, IFB-
Diversity Mixer Differential IF Output. Connect pullup inductors
from each of these pins to VCC (see the Typical Application
Circuit).
17
LO1_ADJ
Connect the specified resistor for either Standard or LC mode
from this pin to ground to set the LO common buffer Icc
19, 27
LO_in
LO_in_alt
Local Oscillator Input. Connect the LO to this port through the
recommended coupling capacitor. Note that you can only
drive one LO port at a time. Remove the series capacitor
from the unused port.
25
LC_MODE
Low_Current Mode. Set this pin to low or ground for LC mode.
Set to high or No-Connect for Standard mode. There is an
internal pull-up resistor.
22
STBY
STBY Mode. Pull this pin high for Standby mode (~20 mA). Pull
low or Ground for normal Operation
29
LO2_ADJ
Connect the specified resistor for either Standard or LC mode
from this pin to ground to set the LO drive buffers Icc
32, 33
IFA-, IFA+
Main Mixer Differential IF Output. Connect pullup inductors from
each of these pins to VCC (see the Typical Application Circuit).
35
IF_BiasA
Connect the specified resistor from this pin to ground to set the
bias for the Main IF amplifier. This is NOT a current set resistor
— EP
Exposed Pad. Internally connected to GND. Solder this exposed
pad to a PCB pad that uses multiple ground vias to provide heat
transfer out of the device into the PCB ground planes. These
multiple via grounds are also required to achieve the noted RF
performance.
RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI
IDT Zero-DistortionTM Mixer 23 Rev2, November 07, 2016
DATASHEET
EVKIT SCHEMATIC
36 35 34 33 32 31 30 29 28
9
RF_B
8
RF_B rtn
7
6
NC
5
4
NC
3
GND
2
RF_A rtn
1
RF_A
18
GND
17
LO1_ADJ
16
VCC
15
NC
14
IF_B-
13
IF_B+
12
NC
11
IF_BiasB
10
VCC
19 LO_in
20
NC
21 VCC
22
LCMODE
23
STBY
24
NC
25
GND
26
LO_in_alt
27
LO_rtn
B
I
A
S
C
T
R
L
C8
J4
C10
J5
C12
Vcc C13
R12
R11
C14
L3 L4
C15
J7
Vcc
R14
R13
C16
Vcc
C9
Vcc
J6
GND
LO2_ADJ
VCC
NC
IF_A-
IF_A+
NC
IF_BiasA
VCC
C5
Vcc C6
R15
R16
C3
L1 L2
C2 J2
Vcc
R17
R18
C1
Vcc
4:1 Balun
4:1 Balun
C11
JP
JP
Vcc
R9 R8
C4
Vcc
GND
GND
T1
T2
J3
C7
R10
J1
RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI
IDT Zero-DistortionTM Mixer 24 Rev2, November 07, 2016
DATASHEET
EVKIT PICTURE/LAYOUT/OPERATION
Outer Position for STD
Mode (R15, R17)
Install Jumper for
Mixer Operation
Remove Jumper to
Turn Mixer Off
Close for LC Mode
Open for STD Mode
Inner Position for LC Mode
(R16, R18)
Outer Position for STD
Mode (R11, R13)
Inner Position for LC Mode
(R12, R14)
Alternate LO Port:
Must remove C11 and
Install C7 to use
RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI
IDT Zero-DistortionTM Mixer 25 Rev2, November 07, 2016
DATASHEET
EVKIT BOM
Default BOM:
For Standard Mode, Open the LCMODE jumper in conjunction with positioning the 4 dual jumpers to select the resistors in
red.
For Low Current Mode close the LCMODE jumper in conjunction with positioning the 4 dual jumpers to select the resistors in
blue.
Modified BOM (for High Side Injection LC Mode):
EVkit Modifications for High Side Injection Low Current Mode (see TOCs on pages 15 – 17)
Item # Value Size
Desc Mfr. Part # Mfr. Part Reference Qty
110nF 0402
CAP CER 10000PF 16V 10% X7R 0402 GRM155R71C103KA01D MURATA C1,5,6,9,12,13,16 7
21000pF 0402
CAP CER 1000PF 50V C0G 0402 GRM1555C1H102JA01D MURATA C2,3,14,15 4
339pF 0402
CAP CER 39PF 50V 5% C0G 0402 GRM1555C1H390JZ010 MURATA C8,10 2
4 4.7pF 0402
CAP CER 4.7PF 50V 5% C0G 0402 GRM1555C1H4R7CZ01D MURATA C11 1
51pF 0402 Note: C7 and C11 cannot be installed together. C7 for Pin27 LO feed. C11 for Pin19 LO feed C7 1
610uF 0603 CAP CER 10UF 6.3V X5R 0603 GRM188R60J106ME47D MURATA C4 1
7 Header 2 Pin TH 2
CONN HEADER VERT SGL 2POS GOLD 961102-6404-AR 3M JP1,2,3 3
8 Header 3 Pin TH 3
CONN HEADER VERT SGL 3POS GOLD 961103-6404-AR 3M JP4,5,6,7 4
9 SMA_END_LAUNCH .062
SMA_END_LAUNCH 142-0711-821 Emerson Johnson J1,2,3,4,5,6,7 7
10 270nH 0805
0805CS (2012) Ceramic Chip Inductor 0805CS-271XJLB COILCRAFT L1,2,3,4 4
11 40 0402
RES 40 OHM 1/10W 1% 0402 SMD ERJ-2RKF40R2X Panasonic R11,15 2
12 63 0402
RES 63 OHM 1/10W 1% 0402 SMD ERJ-2RKF62R0X Panasonic R12,16 2
13 91 0402
RES 91.0 OHM 1/10W 1% 0402 SMD ERJ-2RKF91R0X Panasonic R13 1
14 180 0402
RES 180 OHM 1/10W 1% 0402 SMD ERJ-2RKF1800X Panasonic R14 1
15 1.91k 0402
RES 1.91K OHM 1/10W 1% 0402 SMD ERJ-2RKF1911X Panasonic R18 1
16 1.21K 0402
RES 1.21K OHM 1/10W 1% 0402 SMD ERJ-2RKF1211X Panasonic R17 1
17 47K 0402
RES 47.0K OHM 1/16W 1% 0402 SMD RC0402FR-0747KL Yageo R8,9 2
18 00402
RES 0.0 OHM 1/10W 0402 SMD ERJ-2GE0R00X Panasonic R1,2,3,4,5,6,7,10 8
19 4:1 Balun SM-22
4:1 Center Tap Balun TC4-1TG2+ Mini Circuits T1,2 2
20 F1162 QFN-36
Diversity Downconverter F1162NBGI IDT U1 1
21 PCB F1162 EVKit Rev5 1
F1162 BOM
Set these 3 Dual Jumpers as
shown to INNER position and
CLOSE LCMODE Jumper
Set R14/R13 Jumper to
OUTER position
Will select 91 ohm
resistor for pin17 instead
of 180 ohm. All other
resistors will be selected
for Mode = Low Current
Change C8 and C10
from 39 pF to 4.7 pF
Change C11 from
4.7 pF to 3 pF
RF to IF Dual Downconverting Mixer 2300 - 2700 MHz F1162NBGI
IDT Zero-DistortionTM Mixer 26 Rev2, November 07, 2016
DATASHEET
TOP MARKINGS
REVISION HISTORY SHEET
Rev
Date
Page
Description of Change
O
2012-June-13
Initial Release
1
2012-July-13
3
Changed max STBY Icc from 27 mA to 30 mA
19
Updated EVkit trace loss graph to include loss vs. temperature
10
Updated NF typ ops graph to account for trace loss vs. temperature
1
Added official Zero-Distortion Logo
2
2016-Nov-7
4
Changed typ Channel Isolation from 63 dB to 49 dB
10
Revised all three Channel Isolation typ ops graphs
26
Modified Top Markings drawing
Lot Code
Date Code: [YYWW]
(work week 8 of 2016)
Part Number
IDTF1162
NBGI
YB1608G
XRC02105Y
“G” denotes
assembly site
“YB”
denotes die
& assembly