ESP8266-EVB - Olimex LTD - Datasheet.Live

CHANGING THE MODES OF

MOD-WIFI-ESP8266-DEV

REFERENCE

Revision B, March 2018

All boards produced by Olimex LTD are ROHS compliant

DISCLAIMER

names may be trademarks of others and the rights belong to their respective owners.

The information in this document is provided in connection with Olimex products. No license, express or implied

or otherwise, to any intellectual property right is granted by this document or in connection with the sale of

Olimex products.

This work is licensed under the Creative Commons Attribution-ShareAlike 3.0 Unported License. To view a copy of

this license, visit http://www.creativecommons.org/licenses/by-sa/3.0/.

This hardware design by Olimex LTD is licensed under a Creative Commons Attribution-ShareAlike 3.0 Unported

License.

The software written by Olimex is released under GPL. Some of the demo code might be based on Espressif code, make

sure to check the license that their original software uses. Our demo examples inherit any license of the original code

without changing it to another license.

The product described in this document is subject to continuous development and improvements. All particulars of the

product and its use contained in this document are given by OLIMEX in good faith. However all warranties implied or

expressed including but not limited to implied warranties of merchantability or fitness for purpose are excluded. This

document is intended only to assist the reader in the use of the product. OLIMEX Ltd. shall not be liable for any loss or

damage arising from the use of any information in this document or any error or omission in such information or any

incorrect use of the product.

This evaluation board/kit is intended for use for engineering development, demonstration, or evaluation purposes only

and is not considered by OLIMEX to be a finished end-product fit for general consumer use. Persons handling the

product must have electronics training and observe good engineering practice standards. As such, the goods being

provided are not intended to be complete in terms of required design-, marketing-, and/or manufacturing-related

protective considerations, including product safety and environmental measures typically found in end products that

incorporate such semiconductor components or circuit boards.

Olimex currently deals with a variety of customers for products, and therefore our arrangement with the user is not

exclusive. Olimex assumes no liability for applications assistance, customer product design, software performance, or

infringement of patents or services described herein.

THERE IS NO WARRANTY FOR THE DESIGN MATERIALS AND THE COMPONENTS

USED TO CREATE MOD-WIFI-ESP8266-DEV. THEY ARE CONSIDERED SUITABLE

ONLY FOR MOD-WIFI-ESP8266-DEV.

Page 2 of 5

ESP8266 has three modes of operation: FLASH mode (default), UART mode,

and SDIO mode. By default the board is configured for FLASH mode

operation. FLASH mode means that the board would execute code stored in

the flash memory.

If you wish to change the code that would get executed in FLASH mode you

would often need to set the board to boot in UART mode. This requires

setting GPIO0 low during power-up.

The easiest way to enter UART mode requires you to disconnect the power

supply from the board and then press and hold the button, apply the power

supply (3.3V), release the button. On next power up, do not use the

button and the board would boot in FLASH mode.

The button is available in MOD-WIFI-ESP8266-DEV boards since hardware

revision B.

You can manipulate the position of the on-board SMT jumpers in order to

access each of the three modes. The jumpers are called called GPIO0,

GPIO2 and MTDO. They are located at the top of the board below the UEXT

pads. Each of the jumpers can be set to either position 0 or position 1

(via cutting the connection between the pads of the original position and

soldering together the pads of the desired position). The jumpers are

highlighted on the picture below:

The jumpers for the default FLASH mode were set during production as

follows: GPIO0 is set to position 1; GPIO2 is set to position 1; MTD0 is

set to position 0.

Page 3 of 5

The positions for the all the modes are printed on the board itself. The

table looks like this:

MODE

JUMPER MTDO GPIO0 GPIO2

SDIO 1 x x

UART 0 0 1

FLASH (DEFAULT) 0 1 1

For example:

Initially, you can't update the firmware of MOD-WIFI-ESP8266-DEV since by

the board starts in the default FLASH mode. In order to update the

firmware of the board you would need to change the starting mode to UART.

This is done by:

(1) Using the button: press the button before applying power, then apply

power, then release the button

(2) Changing the position of the jumpers: change the position of jumper

named GPIO0 to 0. After the update is done – change the position of GPIO0

back to 1 again.

In order to change the position of an SMT jumper like that you would need

basic soldering skills. There are two things that you would need to do:

1. Remove the original connection between the pads. If it was made using

soldering – unsolder it and remove the soldering residue. If it was a

hardware PCB connection – make sure to cut between the pads with a sharp

tool (like a sharp cutter).

2. Connect the pads of the desired position – solder together the two

pads. Do not use a large amount of soldering residue. Do not keep the

soldering iron pressed to the board longer than 10 seconds. Make sure

that there is no left-over soldering residue which might lead to

accidental short-circuits.

If you want, you can add wires and a PTH jumper or a slide switch to the

pads of the jumpers. This would allow easier change of the jumpers in

future. There is no need to add button to GPIO0 since such was added in

hardware revision B of the board.

Page 4 of 5

More details about the three different modes might be found in the

ESP8266EX datasheet.

Page 5 of 5