TDH Series 35 Watt DPAK Package Thick Film Power Surface Mount F e at u r e s * 35 Watt power rating at 25C * SMD - DPAK package configuration * Heat resistance to cooling plate: Rth <4.28C/W * A molded case for environmental protection. * Resistor element is electrically insulated from the metal sink tab. Ohmite's TDH resistor is an economical solution to intermediate power application design requirements. TDH's reliable thick film on alumina substrate construction can be easily heat sinked for higher power performance. TDH resistors are ideal for pulse-loading, pre-charge, bleeder, and snubber applications. characteristics Terminal Plating Terminals- SnAg, Thermal Header- German Silver/Nickel Silver Soldering note: During surface mount soldering the soldering temperature profile must not cause the metal tab of this device to exceed 220C (260C for the TDH35H)! Resistance Range 0.05 to 10K other values on request Max. Operating Voltage 350V Insulation Resistance 10G min. Power Rating Depends upon case temperature. See derating curve. DPAK style power package for surface mounting applications; 35W power rating at 25C case temperature. Working Temperature -55C to +175C Range Solder Process The TDH35P cannot exceed 215C (260C for the TDH35H) for more than 10 seconds during soldering process. Derating 100% @ 25C to 0% @ 150C curve referenced to case temperature Dielectric Strength 1,800VAC Operating Temperature -55C to +150C Range Temperature Coefficient 10 and above, 50ppm/C, referenced to 25C, R taken at +105C. Between 1 and 10, (100ppm+0.002)/C, referenced to 25C, R taken at +105C. For under 10: 0R6 - 9R9: 100PPM 0R4 - 0R59: 150PPM 0R2 - 0R39: 250PPM 0R1 - 0R19: 500PPM 0R05 - 0R09: 1000PPM Inductance less than 20 nanohenries Flatness less than 0.1mm tolerance Test Condition Load Life MIL-R-39009, 2,000 hours Result R (1.0% +0.01) Moisture MIL-Std-202, Method 106 Resistance R =(0.5% +0.01) max. Short Time 2 times rated power with Overload applied voltage not to exceed 1.5 times maximum continuous operating voltage for 5 seconds R (0.3% +0.01) max. Thermal Shock MIL-Std-202, Method 107, Cond. F R =(0.3% +0.01) max. Terminal MIL-Std-202, Method 211, Strength Cond. A (Pull Test) 2.4N R =(0.2% +0.01) max. Vibration, High MIL-Std-202, Method 204, Frequency Cond. D R =(0.2% +0.01) max. Derating 100 35 80 28 60 21 40 14 20 7 Percent Rated Power Tolerance 1% to 10% (0.5% on request) 0 Rated Power, W Terminal Copper 0 0 25 50 75 100 125 150 Bottom of base plate Temperature, C 175 Derating (thermal resistance): 0.23W/C (4.28C/W). The case temperature is to be used for purposes of establishing the applied power limit. The case temperature measurement must be made with a thermocouple contacting the center of the component mounted on the designed heat sink. Thermal grease should be applied propperly. (continued) 38 1-866-9-OHMITE * Int'l 1-847-258-0300 * Fax 1-847-574-7522 * www.ohmite.com * info@ohmite.com TDH Series 35 Watt DPAK Package Thick Film Power Surface Mount dimensions 10.1mm 45 0.5mm 4.5mm Tape Dimensions 750 pc./reel 7.87mm 1.1mm 0.5 0.5mm Land Pattern 8.6mm 4.95mm 16mm 8.51mm 24mm 1.4mm 1.5mm 0.5 4.8mm 0.9mm 0.6mm 2.63mm 1.5mm 0.5 3.81mm 5.08mm Tol. 0.2mm unless otherwise noted 1.65mm 2.54mm o r d e r i n g i n f o r m at i o n Standard Part Numbers Ohms T D H 3 5 P R 1 0 0 J E-TR Style Package Modifier P = low temp. H = high temp. Tape and reel (optional) 750 per reel Tolerance RoHS Compliant Ohms R = Decimal F = 1% Non-compliant J = 5% Example: version unavailable R100 = 0.10 K = 10% 1R00= 1.0 10K0= 10,000 0.10 0.15 0.20 0.25 0.30 0.36 0.47 0.50 0.75 1.0 2.0 3.0 5.0 7.5 10 15 20 Part Number 5% Tolerance TDH35PR100JE TDH35PR150JE TDH35PR200JE TDH35PR250JE TDH35PR300JE TDH35PR360JE TDH35PR470JE TDH35PR500JE TDH35PR750JE TDH35P1R00JE TDH35P2R00JE TDH35P3R00JE TDH35P5R00JE TDH35P7R50JE TDH35P10R0JE TDH35P15R0JE TDH35P20R0JE THIS PRODUCT IS DESIGNED FOR USE WITH PROPER HEATSINKING. Maximum base plate temperature of the resistor must be monitored and kept within specified limits to establish the power rating. Best technique is to attach a thermocouple to the side of the base plate of the resistor. Temperature of plastic housing or heat sink cannot be used to establish rating of the resistor. 1-866-9-OHMITE * Int'l 1-847-258-0300 * Fax 1-847-574-7522 * www.ohmite.com * info@ohmite.com 39 Ohms Part Number 5% Tolerance 25 33 39 TDH35P25R0JE TDH35P33R0JE TDH35P39R0JE 200 250 300 500 750 TDH35P200RJE TDH35P250RJE TDH35P300RJE TDH35P500RJE TDH35P750RJE 47 68 75 100 150 1000 1500 2500 3000 5000 TDH35P47R0JE TDH35P68R0JE TDH35P75R0JE TDH35P100RJE TDH35P150RJE TDH35P1K00JE TDH35P1K50JE TDH35P2K50JE TDH35P3K00JE TDH35P5K00JE Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Ohmite: TDH35P5K00JE TDH35PR250JE TDH35P750RJE TDH35P39R0JE TDH35P100RJE TDH35PR470JE TDH35P1K00JE TDH35P68R0JE TDH35PR100JE TDH35P300RJE TDH35P2R00JE TDH35P15R0JE TDH35PR360JE TDH35P10R0JE TDH35P250RJE TDH35P3K00JE TDH35P500RJE TDH35PR200JE TDH35P25R0JE TDH35P20R0JE TDH35P1K50JE TDH35P7R50JE TDH35PR150JE TDH35P75R0JE TDH35P5R00JE TDH35PR750JE TDH35P2K50JE TDH35PR300JE TDH35P200RJE TDH35P1R00JE TDH35P33R0JE TDH35P47R0JE TDH35P3R00JE TDH35PR500JE TDH35P150RJE TDH35HR100JE