LITE-ON SEMICONDUCTOR MBRF10100CT REVERSE VOLTAGE - 100 Volts FORWARD CURRENT - 10 Amperes SCHOTTKY BARRIER RECTIFIERS ITO-220AB FEATURES M B DIM. D A C K PIN 1 2 3 E Metal of silicon rectifier,majority carrier conducton Guard ring for transient protection Low power loss, high efficiency High current capability, low VF High surge capacity Plastic package has UL flammability classification 94V-0 For use in low voltage,high frequency inverters,free whelling,and polarity protection applications IEC 61000-4-2, level 4 (ESD), >15KV (air) J F G I MECHANICAL DATA Case : ITO-220AB molded plastic Polarity : As marked on the body Weight : 0.06 ounces, 1.70 grams Mounting position : Any Max. mounting torque = 0.5 N.m (5.1 Kgf.cm) H N H L PIN 1 PIN 2 PIN 3 ITO-220AB MIN. MAX. A B C 15.50 10.0 3.00 16.50 10.40 3.50 D E 9.00 2.90 9.30 3.60 F 13.46 G H 1.15 2.40 0.75 14.22 1.70 I J K 2.70 1.00 0.45 0.70 3.00 3.30 L 4.36 4.77 M 2.48 2.80 2.80 2.50 N All Dimensions in millimeter MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 ambient temperature unless otherwise specified. CHARACTERISTICS SYMBOL MBRF10100CT UNIT Maximum Recurrent Peak Reverse Voltage @IR=100uA VRRM 100 V Maximum RMS Voltage @IR=100uA VRMS VDC 70 100 V V I(AV) 10 A @IR=100uA Maximum Average Forward RectifiedCurrent at Tc=120 C (See Fig.1) Maximum DC Blocking Voltage Peak Forward Surge Current 8.3ms single half sine-wave @TJ =25 C IFSM 120 A Peak Repetitive Reverse Current tp=2us, square F=1KHz @TJ=25 C IRRM 1 A dv/dt 10000 V/us VF 0.85 0.75 0.95 0.85 V IR 0.01 15 mA CJ 180 pF R0JC 3.0 C/W TJ -55 to +150 -55 to +175 C C 2000 V Voltage Rate of Change (Rated VR) Maximum Forward Voltage, (Note 1) @IF=5A @IF=5A @IF=10A @IF=10A TJ =25 C TJ =125 C TJ =25 C TJ =125 C Maximum DC Reverse Current @TJ =25 C at Rated DC Blocking Voltage @TJ =125 C Typical Junction Capacitance, per element (Note 2) Typical Thermal Resistance (Note 3, 4) Operating Temperature Range Storage Temperature Range TSTG Dielectric Strengh from terminals to case, Vdis AC with t=1 minute, RH<30% NOTES : 1. 300us Pulse Width, 2% Duty Cycle. 2. Measured at 1.0MHz and applied reverse voltage of 4.0V DC. 3. Thermal Resistance Junction to Case. 4. Device mounted on 135mm x 135mm x 8mm Al Plate. REV. 5, Jul-2012, KTHC46 AVERAGE FORWARD CURRENT AMPERES FIG.1 - FORWARD CURRENT DERATING CURVE 10 8 6 4 2 RESISTIVE OR INDUCTIVE LOAD 0 25 50 75 100 125 150 PEAK FORWARD SURGE CURRENT, AMPERES RATING AND CHARACTERISTIC CURVES MBRF10100CT FIG.2 - MAXIMUM NON-REPETITIVE SURGE CURRENT 120 100 80 60 40 20 8.3ms Single Half-Sine-Wave 0 1 175 2 CASE TEMPERATURE , C FIG.3 - TYPICAL REVERSE CHARACTERISTICS 20 10 50 100 FIG.4 - TYPICAL FORWARD CHARACTERISTICS 10000 INSTANTANEOUS FORWARD CURRENT ,(A) 100 TJ = 125 C 1000 TJ = 100 C 100 10 TJ = 25 C 10 1.0 TJ = 25 C PULSE WIDTH 300us 2% Duty cycle 0.1 1 0 20 40 60 80 100 120 0.1 0.2 0.3 0.4 FIG.5 - TYPICAL JUNCTION CAPACITANCE 1000 100 TJ = 25 C, f= 1MHz 10 0.1 1 0.5 0.6 0.7 0.8 0.9 INSTANTANEOUS FORWARD VOLTAGE , VOLTS PERCENT OF RATED PEAK REVERSE VOLTAGE ,(%) CAPACITANCE , (pF) INSTANTANEOUS REVERSE CURRENT ,(uA) 5 NUMBER OF CYCLES AT 60Hz 4 10 REVERSE VOLTAGE , VOLTS 100 1.0 Legal Disclaimer Notice MBRF10100CT Important Notice and Disclaimer LSC reserves the right to make changes to this document and its products and specifications at any time without notice. Customers should obtain and confirm the latest product information and specifications before final design, purchase or use. LSC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does LSC assume any liability for application assistance or customer product design. LSC does not warrant or accept any liability with products which are purchased or used for any unintended or unauthorized application. No license is granted by implication or otherwise under any intellectual property rights of LSC. LSC products are not authorized for use as critical components in life support devices or systems without express written approval of LSC.