I N D U C T O R S December 2017 Inductors for standard circuits Multilayer ferrite MLF series (for automotive) MLF1005 type MLF1005 1005 [0402 inch]* * Dimensions Code JIS[EIA] (2/9) I N D U C T O R S REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 20171212 / inductor_automotive_standard_mlf1005_en.fm (3/9) I N D U C T O R S Product compatible with RoHS directive Halogen-free Compatible with lead-free solders AEC-Q200 Inductors for standard circuits Multilayer ferrite Overview of MLF1005 type FEATURES The lineup includes a wide inductance range. Highly reliable monolithic structure with multilayer integration. APPLICATION Automotive equipment, smart phones, tablet terminals, tuners, LCD-TVs, PDP-TVs, audio equipment, computers, signal processing for modules etc. PART NUMBER CONSTRUCTION MLF Series name 1005 V LxWxH Dimensions (mm) 1005 1.0x0.5x0.5 characteristics G V R10 Inductance (H) 0.010 10N (10nH) R10 0.1 1R0 1 100 10 Inductance tolerance J 5% K 10% M 20% T D25 Packaging style Internal code T Taping D25 OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature range Package quantity Individual weight Operating Storage Type temperature temperature (pieces/reel) C mg C MLF1005 -55 to +125 -55 to +125 10,000 1.2 In case the product's inductance is 15H or higher, both Operating and Storage temperature ranges are -40 to +85C. The Storage temperature range is for after the circuit board is mounted. RoHS Directive Compliant Product: See the following for more details.https://product.tdk.com/info/en/environment/rohs/index.html Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20171212 / inductor_automotive_standard_mlf1005_en.fm (4/9) I N D U C T O R S MLF1005 type RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150C 180C Time t1 60 to 120s Soldering Temp. Time T3 t2 230C 30 to 60s Peak Temp. Time T4 t3 250 to 260C 10s max. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20171212 / inductor_automotive_standard_mlf1005_en.fm (5/9) I N D U C T O R S MLF1005 type 0.500.05 SHAPE & DIMENSIONS 0.10min. 0.10min. 0.500.05 1.000.05 Dimensions in mm 0.5 RECOMMENDED LAND PATTERN 0.5 0.4 0.5 Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20171212 / inductor_automotive_standard_mlf1005_en.fm (6/9) I N D U C T O R S MLF1005 type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L Q (H) 0.10 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.39 0.47 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.2 Tolerance 5%10% 5%10% 5%10% 5%10% 5%10% 5%10% 5%10% 5%10% 5%10% 5%10% 5%10% 5%10% 5%10% 5%10% 5%10% 5%10% 5%10% 5%10% 5%10% 5%10% min. 10 10 15 15 15 15 15 15 15 15 30 30 30 30 30 30 30 30 30 30 L, Q measuring conditions typ. 30 30 30 30 30 30 30 30 30 30 50 55 55 55 60 60 60 60 60 60 Frequency Current (MHz) 25 25 25 25 25 25 25 25 25 25 10 10 10 10 10 10 10 10 10 10 (mA) 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 Self-resonant frequency DC resistance Rated current Part No. (MHz)min. 450 400 350 320 290 260 230 210 190 170 210 190 170 150 130 120 110 100 90 80 ( )max. 0.51 0.59 0.63 0.72 0.79 0.91 1.05 1.35 1.50 1.95 0.41 0.42 0.47 0.55 0.59 0.64 0.79 0.95 1.05 1.30 (mA)max. 180 180 180 160 160 150 140 130 120 120 50 50 45 45 40 40 35 35 30 30 MLF1005VR10 TD25 MLF1005VR12 TD25 MLF1005VR15 TD25 MLF1005VR18 TD25 MLF1005VR22 TD25 MLF1005VR27 TD25 MLF1005VR33 TD25 MLF1005VR39 TD25 MLF1005VR47 TD25 MLF1005VR56 TD25 MLF1005GR39 TD25 MLF1005GR47 TD25 MLF1005GR56 TD25 MLF1005GR68 TD25 MLF1005GR82 TD25 MLF1005G1R0 TD25 MLF1005G1R2 TD25 MLF1005G1R5 TD25 MLF1005G1R8 TD25 MLF1005G2R2 TD25 (MHz)typ. 880 800 650 600 450 450 380 330 300 250 600 460 450 360 320 290 230 200 180 150 ( )typ. 0.33 0.33 0.39 0.40 0.47 0.65 0.80 0.89 0.95 1.35 0.24 0.25 0.34 0.43 0.43 0.45 0.55 0.68 0.75 0.99 The " " of the Part Number contains the inductance tolerance code, J (5%), K (10%), or M (20%). Measurement equipment Measurement item Product No. L, Q 4294A+16034G Self-resonant frequency E4991A DC resistance Type-7561 Equivalent measurement equipment may be used. Manufacturer Keysight Technologies Keysight Technologies Yokogawa Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20171212 / inductor_automotive_standard_mlf1005_en.fm (7/9) I N D U C T O R S MLF1005 type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 10 G1R8 G1R2 Inductance(H) 1 GR39 GR82 GR56 VR33 VR22 0.1 VR15 VR10 VR47 0.01 1 10 100 1000 Frequency(MHz) 10 G2R2 G1R5 Inductance(H) GR47 G1R0 1 GR68 VR39 VR27 VR18 VR12 0.1 VR56 0.01 1 10 100 1000 Frequency(MHz) Measurement equipment Product No. Manufacturer E4991A+16192A Keysight Technologies Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20171212 / inductor_automotive_standard_mlf1005_en.fm (8/9) I N D U C T O R S MLF1005 type ELECTRICAL CHARACTERISTICS Q FREQUENCY CHARACTERISTICS GRAPH 70 60 GR39 G1R2 VR10 50 VR22 GR56 G1R8 GR82 VR47 40 Q VR33 VR15 30 20 10 0 1 10 100 1000 Frequency(MHz) 70 G1R0 60 VR27 50 VR56 GR68 GR47 VR12 Q 40 VR18 G1R5 30 VR39 G2R2 20 10 0 1 10 100 1000 Frequency(MHz) Measurement equipment Product No. Manufacturer E4991A+16192A Keysight Technologies Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20171212 / inductor_automotive_standard_mlf1005_en.fm (9/9) I N D U C T O R S MLF1005 type PACKAGING STYLE REEL DIMENSIONS o60min. 1.0 2.00.5 8.4 +2.0 -0.0 o130.2 14.4max. o210.8 o1802.0 Dimensions in mm Cavity 3.50.05 1.5 +0.1 -0.0 Type MLF1005 A 1.150.1 B 0.650.1 K 0.8 max. A 8.00.3 Sprocket hole 1.750.1 TAPE DIMENSIONS K B 4.00.1 2.00.05 160min. Drawing direction Taping 2.00.05 200min. 300min. Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20171212 / inductor_automotive_standard_mlf1005_en.fm