AMB2300 www.amber-wireless.de Embedded Bluetooth Module BlueNiceCom 4 Key Features Bluetooth radio module (Class 2) Bluetooth 2.0 specification Digital AUDIO interface (PCM interface) Integrated profiles: SPP, GAP, SDAP Supported profiles: DUN, FAX, FTP, HSP, HFP, OPP, SYNC, BIP, BPP Small form factor Integrated chip antenna UART interface with programmable baud rate EN 300 328 compliant Description The BlueNiceCom 4 module (BNC4) is a completely integrated Bluetooth solution, containing Bluetooth radio (LMX9830), antenna and a fully implemented software protocol stack. The module provides reliable Bluetooth data communication links as well as AUDIO communication links. Thus the module supports AUDIO gateway applications (e.g. Headset or Handsfree). The module features point-to-point and point-to-multipoint link management supporting data rates up to 704 kbps. The internal memory supports up to 7 active Bluetooth ACL links (data) and one SCO link (AUDIO). BlueNiceCom 4 is supplied with an onboard chip antenna. Depending on the respective application, BlueNiceCom 4 can either be linked to a processor via serial UART-interface or directly to a terminal device. Configuration of the module is being effected through a host processor. Depending on the application and pre-parameterisation, BlueNiceCom 4 can either be operated as `master' module or as stand-alone `slave' module. The module supports automatic `slave' operation eliminating the need for an external control unit. The BlueNiceCom 4 module enables OEMs and designers to easily add wireless Bluetooth communication to their products without the need for RF and antenna design expertise. The surface-mounted AMB2300 radio module is available in Tape & Reel packaging for automatic component placement. Firmware The firmware supplied within this module offers a complete Bluetooth stack 2.0. BlueNiceCom 4 Profiles Profiles supported in combination with a host system SPP (Serial Port Profile) DUN (Dial up Networking Profile) GAP (Generic Access Profile) FAX (Facsimile Profile) SDAP (Service Discovery Access Profile) FTP (File Transfer Profile) HSP (Headset Profile) HFP (Handsfree Profile) OPP (Object Push Profile) SYNC (Synchronisation Profile) BIP (Basic Imaging Profile) BPP (Basic Printing Profile) Evaluation-Kit The Quick-Start Evaluation Kit AMB2300-EV enables genuine quick and easy evaluation and application development, based on the BlueNiceCom 4 module. AMB2300 www.amber-wireless.de Pin out Pin Assignment Pad Name Type1 Description GND I Ground OP3 I Configuration of UART data rate at start up, otherwise internal use PG7 I/O GPIO (default setting: UART activity) SCLK I/O Audio PCM Interface Clock SFS I/O Audio PCM Interface Frame Synchronization SRD I Audio PCM Interface Receive Data Input STD O Audio PCM Interface Transmit Data Output OP5 I/O Configuration of UART data rate at start up OP4 I I/O Configuration of UART data rate at start up, otherwise GPIO RESETBB# I Reset-Input, Internal Pull up, active low CTS#_BT I Host Serial Port Clear To Send, active low RTS#_BT O Host Serial Port Request To Send, active low TX_BT O Host Serial Port Transmit Data RX_BT I Host Serial Port Receive Data PG6 I/O GPIO (default setting: BT link status) NC I Not connected, no ground Vcc I Power supply 2.9V to 3.6V Antenna O Connector for external antenna, see: User's manual Specifications Performance General RF technology Conformity Range* max. 20 m RF data rate max. 704 kbps Data rate (serial) 9.6 kbps to 921.6 kbps, RF output power typ. 0 dBm RF sensitivity typ. -80 dBm Power consumption typ. 65 mA Dimensions 27.5 x 16.0 x 3.5 mm Operating temperature -20 to +70 C Weight <2g Antenna Ceramic antenna RF transceiver LMX9830 Software Complete Bluetooth (2.0) Stack Frequency 2.4 GHz Channels 79 channels Modulation FHSS Europe EN 300 328 * Range stated is calculated assuming line-of-sight. Actual range will vary based upon specific board integration, antenna selection, and environment. Related Products 2012 AMBER wireless GmbH AMB2300 DS EN V1.2 AMB2300-EV Evaluation-Kit BNC 4 Ordering information Item No. Description AMB2300 Bluetooth 2.0 Module AMBER wireless GmbH Phone +49.651.993.550 Email info@amber-wireless.de Internet www.amber-wireless.de 1 Typ: I = Input, O = Output AMBER wireless GmbH assumes that the statements made in this data sheet are correct at the time of issue. AMBER wireless GmbH reserves the right to make changes to technical specifications or product functions without prior notice. AMBER wireless GmbH does not assume any responsibility for the use of the described products, neither does it convey any license under its patent rights. All trademarks, registered trademarks and product names are the property of their owners.