LITE-ON DCC
RELEASE
LITE-ON Technology Corp. / Optoelectronics
No.90,Chien 1 Road, Chung Ho, New Taipei City 23585, Taiwan, R.O.C.
Tel: 886-2-2222-6181 Fax: 886-2-2221-1948 / 886-2-2221-0660
http://www.liteon.com/opto
LED Display
Product Data Sheet
LTM-8530P
Spec No.: DS-30-98-339
Effective Date: 06/23/2000
Revision: -
BNS-OD-FC001/A4
BNS-OD-FC001/A4
BNS-OD-FC001/A4
BNS-OD-FC001/A4
LITE-ON ELECTRONICS, INC.
Property
of
Lite-On
Only
PART NO.: LTM-8530P
PAGE: 1
of
8
BNS-OD-C131/A4
FEATURES
＊0.56 INCH (14.22 mm) DIGIT HEIGHT.
＊WIDE SUPPLY VOLTAGE OPERATION.
＊SERIAL DATA INPUT.
＊CONSTANT CURRENT DRIVERS.
＊CONTINUOUS BRIGHTNESS CONTROL.
＊SOLID STATE RELIABILITY-LONG OPERATION LIFE.
＊WIDE VIEWING ANGLE.
＊TTL COMPATIBLE.
DESCRIPTION
The LTM-8530P is a 0.56 inch (14.22 mm) numeric display
modules, and a built-in M5450 MOS integrated circuits. The
integrated circuit contains serial data input, 35 bits shift register.
34 LED driver output and a brightness control. This device
utilizes bright red LED chips, which are made from GaP on a
transparent GaP substrate, and has a black face and red segments.
The MOS integrated circuits are produced with N-channel silicon
gate technology.
DEVICE
PART NO.
DESCRIPTION
BRIGHT RED
2 Digit
Rt. Hand Decimal
LTM-8530P
LITE-ON ELECTRONICS, INC.
Property
of
Lite-On
Only
PART NO.: LTM-8530P
PAGE: 2
of
8
BNS-OD-C131/A4
PACKAGE DIMENSIONS
NOTES: All dimensions are in millimeters. Tolerances are 0.25 mm (0.01“) unless otherwise noted.
LITE-ON ELECTRONICS, INC.
Property
of
Lite-On
Only
PART NO.: LTM-8530P
PAGE: 3
of
8
BNS-OD-C131/A4
PIN CONNECTION
No.
CONNECTION
1
VSS
2
VLED
3
NO PIN
4
NO PIN
5
NO PIN
6
BIT 17 OUTPUT
7
BIT 18 OUTPUT
8
BIT 19 OUTPUT
9
BIT 20 OUTPUT
10
BIT 21 OUTPUT
11
BIT 22 OUTPUT
12
BIT 23 OUTPUT
13
BIT 24 OUTPUT
14
DATA ENABLE
15
DATA INPUT
16
CLOCK INPUT
17
VDD
18
BRT. CONTROL
LITE-ON ELECTRONICS, INC.
Property
of
Lite-On
Only
PART NO.: LTM-8530P
PAGE: 4
of
8
BNS-OD-C131/A4
ABSOLUTE MAXIMUM RATING AT TA=25oC
PARAMETER
Symbol
Min.
Max.
UNIT
Supply Voltage *1
VDD
-0.3
12
V
Input Voltage
VI
-0.3
12
V
Off State Output Voltage
VO(off)
12
V
LED Supply Voltage
VLED
2.8
3.5
V
Power Dissipation of IC *2
PD(IC)
335
mW
Supply Current
IDD
8.5
mA
Operating Temperature Range
Top
-20
+60
℃
Storage Temperature Range
Tstg
-20
+60
℃
Solder Temperature: max 260℃ for max 3sec at 1.6mm below seating plane.
Note: 1. All voltage are with respect to Vss(GND)
2. Power dissipation of IC is given by PD=(VLED-VF) • (IF) • (No. of Segments)+(8.5mA) • (VDD)
*VF is LED forward voltage.
RECOMMENDED OPERATING CONDITION AT TA=25oC
Parameter
Symbol
Min.
Typ.
Max.
Unit
Test Condition
Supply Voltage
VDD
4.75
11
V
Input Voltage
Logical “0” Level
Logical “1” Level
Logical “1” Level
VI
-0.3
2.2
VDD -2
0.8
VDD
VDD
V
V
V
±10µA Input Bias
4.75V < VDD < 5.25V
VDD > 5.25V
Brightness Input Current
IB
0
0.75
mA
Brightness Input Voltage
VB
3
4.3
V
Input Current=750μA
Off State Voltage
VO(off)
11
V
Output Sink Current
Segment Off
Segment On
Input Clock Frequency
FCLOCK
0
3
6
10
0.5
μA
mA
mA
MHZ
IB=0 µA
IB=100 µA
IB=200 µA
Output Matching
IO
±20
%
LITE-ON ELECTRONICS, INC.
Property
of
Lite-On
Only
PART NO.: LTM-8530P
PAGE: 5
of
8
BNS-OD-C131/A4
ELECTRICAL/OPTICAL CHARACTERISTICS AT Ta=25℃
PARAMETER
SYMBOL
MIN.
TYP.
MAX.
UNIT
TEST CONDITION
Average Luminous Intensity
IV
320
950
cd
IB=0.4mA
Peak Emission Wavelength
p
697
nm
IB=0.4mA
Spectral Line Half-Width
90
nm
IB=0.4mA
Dominant Wavelength
d
657
nm
IF=20mA
Luminous Intensity Matching Ratio
IV-m
2:1
IB=0.4mA
FUNCTIONAL DESCRIPTION
Serial data transfer from the data source to the display driver is accomplished with 2
signals serial data and clock. Using a format of a leading “1” followed by the 35 data bits
allow data transfer without an additional load signal. The 35 data bits are latched after the
36th bit is completed, thus providing non multiplexed, direct drive to the display. Outputs
change only if the serial data bits differ from the previous time.
Brightness of display is determined by control the output current of LED display. A 1nF
capacitor should be connected to brightness control, Pin 7 to prevent possible oscillations.
The output current is typically 25 times greater than the current into Pin 7 which is set by
an external variable resistor. There is an internal limiting resistor of 400 Ω nominal
value.
Figure 1 shows the input data format. A start bit of logical “1” proceed the 35 bits of data.
At the 36th clock, a LOAD signal is generated synchronously with the high state of the
clock, which loads the 35 bits of the shift registers into the latches. At the low state of the
clock a RESET signal is generated which clears all the shift registers for the next set of
data. The shift registers are static master-slave configuration. There is no clear for master
portion of the first register, thus allowing continuous operation.
There must be a complete set of 36 clocks or the shift registers won’t clear. When power is
first applied to the chip, an internal power ON, a reset signal is generated which reset all
registers and all latches. The START bit and first clock return the chip on its normal
operation. Bit 1 is the first following the start bit and it will appear on the segment A of the
digit 1. A logical “1” at the input will turn on the appropriate LED. Figure 2 shows the
timing relationship between data, clock, and DATA ENABLE. A max. clock frequency of
0.5 MHz is assumed.
LITE-ON ELECTRONICS, INC.
Property
of
Lite-On
Only
PART NO.: LTM-8530P
PAGE: 6
of
8
BNS-OD-C131/A4
FIGURE 1. INTERNAL BLOCK DIAGRAM
FIGURE 2. INPUT DATA FORMAT
FIGURE 3. TIMING RELATIONSHIP
LITE-ON ELECTRONICS, INC.
Property
of
Lite-On
Only
PART NO.: LTM-8530P
PAGE: 7
of
8
BNS-OD-C131/A4
TABLE 1 SERIAL DATA INPUT SEQUENCE
L T M-85 30
BIT DIGIT SEGMENT
1 1 A
2 1 B
3 1 C
4 1 D
5 1 E
6 1 F
7 1 G
8 1 D.P.
9 2 A
10 2B
11 2C
12 2D
13 2E
14 2F
15 2G
16 2D.P.
17 PIN 6
18 PIN 7
19 PIN 8
20 PIN 9
21 PIN 10
22 PIN 11
23 PIN 12
24 PIN 13
25 NO CONNECTION
26 NO CONNECTION
27 NO CONNECTION
28 NO CONNECTION
29 NO CONNECTION
30 NO CONNECTION
31 NO CONNECTION
32 NO CONNECTION
33 NO CONNECTION
34 NO CONNECTION
LITE-ON ELECTRONICS, INC.
Property
of
Lite-On
Only
PART NO.: LTM-8530P
PAGE: 8
of
8
BNS-OD-C131/A4
TYPICAL APPLICATION
NOTES: 1. Clean only in water, isopropanol, ethanol, freon TF(or equivalent).
2. Luminous intensity is measured with a light sensor and filter combination that
approximates the CIE (Commision Internationale De L’Eclairage)eye-response curve.
