General Description
Maxim’s redesigned DG411/DG412/DG413 analog
switches now feature low on-resistance matching
between switches (3Ωmax) and guaranteed on-resis-
tance flatness over the signal range (∆4Ωmax). These
low on-resistance switches conduct equally well in
either direction. They guarantee low charge injection,
low power consumption, and an ESD tolerance of
2000V minimum per Method 3015.7. The new design
offers lower off-leakage current over temperature (less
than 5nA at +85°C).
The DG411/DG412/DG413 are quad, single-pole/sin-
gle-throw (SPST) analog switches. The DG411 is nor-
mally closed (NC), and the DG412 is normally open
(NO). The DG413 has two NC switches and two NO
switches. Switching times are less than 150ns max for
tON and less than 100ns max for tOFF. These devices
operate from a single +10V to +30V supply, or bipolar
±4.5V to ±20V supplies. Maxim’s improved
DG411/DG412/DG413 are fabricated with a 44V silicon-
gate process.
________________________Applications
Sample-and-Hold Circuits Communication Systems
Test Equipment Battery-Operated Systems
Heads-Up Displays PBX, PABX
Guidance & Control Systems Audio Signal Routing
Military Radios
______________________New Features
♦Plug-In Upgrade for Industry-Standard
DG411/DG412/DG413
♦Improved RDS(ON) Match Between Channels
(3Ωmax)
♦Guaranteed RFLAT(ON) Over Signal Range (∆4Ω)
♦Improved Charge Injection (10pC max)
♦Improved Off-Leakage Current Over Temperature
(<5nA at +85°C)
♦Withstand Electrostatic Discharge (2000V min)
per Method 3015.7
__________________Existing Features
♦Low RDS(ON) (35Ωmax)
♦Single-Supply Operation +10V to +30V
♦Bipolar-Supply Operation ±4.5V to ±20V
♦Low Power Consumption (35µW max)
♦Rail-to-Rail Signal Handling
♦TTL/CMOS-Logic Compatible
Ordering Information
DG411/DG412/DG413
Improved, Quad,
SPST Analog Switches
________________________________________________________________ Maxim Integrated Products 1
SWITCHES SHOWN FOR LOGIC “0” INPUT
DIP/SO/TSSOP
DG412
LOGIC SWITCH
0
1
OFF
ON
TOP VIEW
DIP/SO/TSSOP
DG411
LOGIC SWITCH
0
1
ON
OFF
DIP/SO/TSSOP
DG413
LOGIC SWITCHES
1, 4
0
1
OFF
ON
SWITCHES
2, 3
ON
OFF
16
15
14
13
12
11
10
9
1
2
3
4
5
6
7
8
IN2
D2
S2
V+
V-
S1
D1
IN1
DG413 VL
S3
D3
IN3
IN4
D4
S4
GND
16
15
14
13
12
11
10
9
1
2
3
4
5
6
7
8
IN2
D2
S2
V+
V-
S1
D1
IN1
DG411 VL
S3
D3
IN3
IN4
D4
S4
GND
16
15
14
13
12
11
10
9
1
2
3
4
5
6
7
8
IN2
D2
S2
V+
V-
S1
D1
IN1
DG412 VL
S3
D3
IN3
IN4
D4
S4
GND
_____________________Pin Configurations/Functional Diagrams/Truth Tables
19-4728; Rev 5; 6/04
Ordering Information continued at end of data sheet.
*Contact factory for dice specifications.
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
Pin Configurations continued at end of data sheet.
PART TEMP RANGE PIN-PACKAGE
16 Plastic DIP0°C to +70°C
DG411CJ
16 Narrow SO0°C to +70°CDG411CY
DG411C/D 0°C to +70°C Dice*
16 TSSOP0°C to +70°CDG411CUE
DG411/DG412/DG413
Improved, Quad,
SPST Analog Switches
2_______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS—Dual Supplies
(V+ = 15V, V- = -15V, VL= 5V, GND = 0V, VINH = 2.4V, VINL = 0.8V, TA= TMIN to TMAX, unless otherwise noted.)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Note 1: Signals on S, D, or IN exceeding V+ or V- are clamped by internal diodes. Limit forward current to maximum
current rating.
(Voltage Referenced to V-)
V+.........................................................................................44V
GND .....................................................................................25V
VL.....................................................(GND -0.3V) to (V+ +0.3V)
Digital Inputs, VS, VD(Note 1)........(V- -2V) to (V+ +2V) or 30mA
(whichever occurs first)
Continuous Current (any terminal)......................................30mA
Peak Current
(pulsed at 1ms, 10% duty cycle max) ............................100mA
Continuous Power Dissipation (TA= +70°C)
16-Pin Plastic DIP (derate 10.53mW/°C above +70°C) .842mW
16-Pin Narrow SO (derate 8.70mW/°C above +70°C) ...696mW
16-Pin CERDIP (derate 10.00mW/°C above +70°C)......800mW
16-Pin TSSOP (derate 6.7mW/°C above +70°C) ...........457mW
16-Pin QFN (derate 19.2mW/°C above +70°C) ...........1538mW
Operating Temperature Ranges
DG41_C_ ..............................................................0°C to +70°C
DG41_D_ ...........................................................-40°C to +85°C
DG41_AK_ .......................................................-55°C to +125°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
17 30
A
C, D
-40 40
-10 10
-10 10
-0.25 -0.10 0.25
6
5
A
A
A
TA= TMIN to TMAX
TA= TMIN to TMAX
C, D
C, D
C, D
TA= TMIN to TMAX
TA= +25°C
TA= TMIN to
TMAX
TA= +25°C
TA= TMIN to
TMAX
TA= +25°C
TA= TMIN to
TMAX
TA= +25°C
TA= +25°C
TA= +25°C
V+ = 16.5V,
V- = -16.5V,
VD= ±15.5V,
VS= 15.5V
V+ = 16.5V,
V- = -16.5V,
VD= ±15.5V,
VS= 15.5V
(Note 3)
V+ = 16.5V,
V- = -16.5V,
VD= ±15.5V,
VS= 15.5V
V+ = 15V, V- = -15V,
VD= ±10V,
IS= -10mA
V+ = 13.5V,
V- = -13.5V,
VD= ±8.5V,
IS= -10mA
V+ = 15V, V- = -15V,
VD= ±5V, 0V,
IS= -10mA
CONDITIONS
nA
-20 20
ID(ON)
+
IS(ON)
Drain On-Leakage Current
(Note 7)
-0.4 -0.1 0.4
ID(OFF) nA
-5 5
Drain Off-Leakage Current
(Note 7)
-5 5 nAIS(OFF)
Source Off-Leakage Current
(Note 7)
-0.25 -0.10 0.25
Ω
4
rFLAT(ON)
On-Resistance Flatness
(Note 4)
V-15 15VANALOG
Analog Signal Range
∆rDS(ON)
On-Resistance
Match Between Channels
(Note 4)
Ω
3
17 45
Ω
45
rDS(ON)
Drain-Source
On-Resistance
UNITS
MIN TYP MAX
(Note 2)
SYMBOLPARAMETER
C, D, A
C, D, A
C, D, A
SWITCH
±
±
±
IN = 2.4V, all others = 0.8V
DG411/DG412/DG413
Improved, Quad,
SPST Analog Switches
_______________________________________________________________________________________ 3
ELECTRICAL CHARACTERISTICS—Dual Supplies (continued)
(V+ = 15V, V- = -15V, VL= 5V, GND = 0V, VINH = 2.4V, VINL = 0.8V, TA= TMIN to TMAX, unless otherwise noted.)
ns
ns
-5 5TA= TMIN to TMAX
-5 5TA= TMIN to TMAX
TA= +25°C
-5 5TA= TMIN to TMAX
-5 5TA= TMIN to TMAX
TA= +25°C
TA= +25°C
TA= +25°C
TA= +25°C
TA= +25°C
TA= +25°C
TA= +25°C
TA= TMIN to TMAX
TA= +25°C
TA= TMIN to TMAX
TA= +25°C
TA= +25°C
IN = 0.8V, all others = 2.4V
TA= +25°C
CONDITIONS
TA= +25°C
-1 -0.0001 1
All channels on or off,
V+ = 16.5V,
V- = -16.5V,
VIN = 0V or 5V
All channels on or off,
V+ = 16.5V,
V- = -16.5V,
VIN = 0V or 5V
All channels on or off,
V+ = 16.5V,
V- = -16.5V,
VIN = 0V or 5V
pF35f = 1MHz, Figure 8
CD(ON) +
CS(ON)
Drain On-Capacitance
pF9f = 1MHz, Figure 7CD(OFF)
Drain Off-Capacitance
pF9f = 1MHz, Figure 7CS(OFF)
Source Off-Capacitance
dB85
RL= 50Ω,
CL= 5pF,
f = 1MHz, Figure 6
Crosstalk (Note 6)
dB68
RL= 50Ω,
CL= 5pF,
f = 1MHz, Figure 5
OIRROff-Isolation (Note 5)
pC510
CL= 1.0nF,
VGEN = 0V,
RGEN = 0Ω, Figure 4
QCharge Injection (Note 3)
ns25
DG413 only,
RL= 300Ω,
CL= 35pF, Figure 3
tD
Break-Before-Make Time Delay
VD= ±10V,
Figure 2
VD= ±10V,
Figure 2
160
tOFF
Turn-Off Time 100 145
220
tON
Turn-On Time
µA-0.500 0.005 0.500IINH
110 175
Input Current with Input Voltage
High
-1 -0.0001 1
µAIGND
Ground Current
µA
-1 0.0001 1
IL
Logic Supply Current
µA
-1 0.0001 1
I+Positive Supply Current
µA
µA
-0.500 0.005 0.500IINL
Input Current with Input Voltage
Low
All channels on or off,
V+ = 16.5V,
V- = -16.5V,
VIN = 0V or 5V
V
I-Negative Supply Current
±4.5 ±20.0Power-Supply Range
UNITS
MIN TYP MAX
(Note 2)
SYMBOLPARAMETER
INPUT
SUPPLY
DYNAMIC
DG411/DG412/DG413
Improved, Quad,
SPST Analog Switches
4_______________________________________________________________________________________
ELECTRICAL CHARACTERISTICS—Single Supply
(V+ = 12V, V- = 0V, VL= 5V, GND = 0V, VINH = 2.4V, VINL = 0.8V, TA= TMIN to TMAX, unless otherwise noted.)
Note 2: The algebraic convention, where the most negative value is a minimum and the most positive value a maximum, is used in
this data sheet.
Note 3: Guaranteed by design.
Note 4: ∆RON = ∆RON max - ∆RON min. On-resistance match between channels and flatness are guaranteed only with
bipolar-supply operation. Flatness is defined as the difference between the maximum and minimum value of on-resistance
as measured at the extremes of the specified analog signal range.
Note 5: Off-Isolation = 20 log (VD/VS), VD= output, VS= input to off switch. See Figure 5.
Note 6: Between any two switches. See Figure 6.
Note 7: Leakage parameters IS(OFF), ID(OFF), and ID(ON) are 100% tested at the maximum-rated hot temperature and guaranteed
by correlation at +25°C.
-5 5
TA= +25°C
TA= TMAX
-5 5TA= TMAX
-5 5TA= TMAX
315TA= TMIN to TMAX
-5 5TA= TMAX
TA= +25°C
TA= +25°C
TA= TMIN to TMAX
TA= +25°C
TA= +25°C
TA= +25°C
TA= +25°C
TA= +25°C
TA= +25°C
TA= TMIN to TMAX
CONDITIONS
pC510
CL= 1.0nF,
VGEN = 0V,
RGEN = 0V,
Figure 4
Q
Charge Injection
(Note 3)
ns25
DG413 only,
RL= 300Ω, CL= 35pF,
Figure 3
tD
Break-Before-Make Time Delay
VS= 8V,
Figure 2
VS= 8V,
Figure 2
All channels on or off,
VL= 5.25V,
VIN = 0V or 5V
All channels on or off,
V+ = 13.2V,
VIN = 0V or 5V
All channels on or off,
VL= 5.25V,
VIN = 0V or 5V
All channels on or off,
V+ = 13.2V,
VIN = 0V or 5V
V+ = 10.8V,
VD= 3.8V,
IS= -10mA
ns
140
tOFF
Turn-Off Time
40 80
95 125
tON ns
175 250
V012VANALOG
Turn-On Time
µA
-1 -0.0001 1
IGND
Analog Signal Range
Ground Current
µA
-1 0.0001 1
I-Negative Supply Current
µA
-1 0.0001 1
IL
µA
-1 0.0001 1
I+Positive Supply Current
Logic Supply Current
Ω
100
RDS(ON)
Drain-Source On-Resistance
UNITS
MIN TYP MAX
(Note 2)
SYMBOLPARAMETER
SWITCH
SUPPLY
DYNAMIC
(Note 3)
DG411/DG412/DG413
Improved, Quad,
SPST Analog Switches
_______________________________________________________________________________________ 5
60
-20 -10 10
ON-RESISTANCE vs. VD AND
POWER-SUPPLY VOLTAGE
0
40
DG411-01
VD (V)
rDS(ON) (Ω)
020
20
50
30
10
70
A
BC
D
A: V+ = 5V,
V- = -5V
B: V+ = 10V,
V- = -10V
C: V+ = 15V,
V- = -15V
D: V+ = 20V,
V- = -20V
0
-20 -10 10
ON-RESISTANCE vs. VD AND
TEMPERATURE
50
DG411-02
VD (V)
rDS(ON) (Ω)
020
30
10
40
20
60
V+ = 15V
V- = -15V
TA = +125°C
TA = +85°C
TA = +25°C
TA = -55°C
20
05 15
ON-RESISTANCE vs. VD AND
TEMPERATURE (SINGLE SUPPLY)
120
DG411-03
VD (V)
rDS(ON) (Ω)
10 20
80
40
100
60
140
V- = 0V
V+ = 5V
V+ = 10V
V+ = 15V V+ = 20V
160
20
05 15
ON-RESISTANCE vs. VD
(SINGLE SUPPLY)
70
DG411-04
VD (V)
rDS(ON) (Ω)
10 20
50
30
60
40
80 V+ = 12V
V- = 0V TA = +125°C
TA = +85°C
TA = +25°C
0.0001
-55
OFF-LEAKAGE CURRENTS vs.
TEMPERATURE
10
DG411-05
TEMPERATURE (°C)
OFF-LEAKAGE (nA)
+25 +125
0.1
0.001
1
0.01
100 V+ = 16.5V
V- = -16.5V
VD = ±15V
VS = 15V
±
0.0001
-55
ON-LEAKAGE CURRENTS vs.
TEMPERATURE
10
DG411-06
TEMPERATURE (°C)
ON-LEAKAGE (nA)
+25 +125
0.1
0.001
1
0.01
100 V+ = 16.5V
V- = -16.5V
VD = ±15V
VS = ±15V
__________________________________________Typical Operating Characteristics
(TA = +25°C, unless otherwise noted.)
-60
-20
CHARGE INJECTION vs.
ANALOG VOLTAGE
40
DG411-07
VD (V)
Q (pC)
020
0
-40
20
-20
60
-15 -10 -5 5 10 15
V+ = 15V
V- = -15V
VL = 5V
CL = 1nF
0.0001
-55
SUPPLY CURRENT vs. TEMPERATURE
10
DG411-08
TEMPERATURE (°C)
I+, I-, IL (µA)
+25 +125
0.1
0.001
1
0.01
100 A: I+ at V+ = 16.5V
B: I- at V- = -16.5V
C: IL at VL = 5V
A
B
C
DG411/DG412/DG413
Improved, Quad,
SPST Analog Switches
6_______________________________________________________________________________________
__________Applications Information
Operation with Supply Voltages
Other Than 15V
Using supply voltages other than 15V will reduce the
analog signal range. The DG411/DG412/DG413 switch-
es operate with ±4.5V to ±20V bipolar supplies or with
a +10V to +30V single supply; connect V- to 0V when
operating with a single supply. Also, all device types
can operate with unbalanced supplies such as +24V
and -5V. VLmust be connected to +5V to be TTL com-
patible, or to V+ for CMOS-logic level inputs. The
Typical Operating Characteristics graphs show typical
on-resistance with ±15V, ±10V, and ±5V supplies.
(Switching times increase by a factor of two or more for
operation at ±5V.)
Overvoltage Protection
Proper power-supply sequencing is recommended for
all CMOS devices. Do not exceed the absolute maxi-
mum ratings because stresses beyond the listed rat-
ings may cause permanent damage to the devices.
Always sequence V+ on first, followed by VL, V-, and
logic inputs. If power-supply sequencing is not possi-
ble, add two small, external signal diodes in series with
supply pins for overvoltage protection (Figure 1).
Adding diodes reduces the analog signal range to 1V
below V+ and 1V below V-, without affecting low switch
resistance and low leakage characteristics. Device
operation is unchanged, and the difference between
V+ and V- should not exceed +44V.
V+
S
V-
D
Vg
V+
V-
Figure 1. Overvoltage Protection Using External Blocking Diodes
______________________________________________________________Pin Description
PIN
DIP/SO/TSSOP QFN
NAME
FUNCTION
1, 16, 9, 8 15, 14, 7, 6
IN1–IN4
Input
2, 15, 10, 7 16, 13, 8, 5
D1–D4
Analog Switch Drain Terminal
3, 14, 11, 6 1, 12, 9, 4
S1–S4
Analog Switch Source Terminal
42V- Negative-Supply Voltage Input
53
GND
Ground
12 10 VLLogic Supply Voltage
13 11 V+ Positive-Supply Voltage Input—Connected to Substrate
DG411/DG412/DG413
Improved, Quad,
SPST Analog Switches
_______________________________________________________________________________________ 7
tr < 20ns
tf < 20ns
50%
0V
LOGIC
INPUT
V-
-15V
RL
300Ω
D1
GND
CL INCLUDES FIXTURE AND STRAY CAPACITANCE.
VOUT = VS ( RL )
RL + RDS(ON)
SWITCH
INPUT
IN1
+3V
tOFF
0V
SWITCH OUTPUT
0.9 x VOUT 0.9 x VOUT
tON
VOUT
SWITCH
OUTPUT
LOGIC
INPUT
LOGIC INPUT WAVEFORMS INVERTED FOR SWITCHES
THAT HAVE THE OPPOSITE LOGIC SENSE.
VLV+
CL
35pF
+5V +15V
VOUT
S1
0V
REPEAT TEST FOR IN AND S, FOR LOAD
CONDITIONS, SEE Electrical Characteristics.
DG411
DG412
DG413
50%
0.9 x VOUT1
+3V
0V
0V
LOGIC
INPUT
SWITCH
OUTPUT 2
(VO2)
0V
0.9 x VOUT2
tDtD
LOGIC
INPUT V-
-15V
RL2
GND
CL INCLUDES FIXTURE AND STRAY CAPACITANCE.
S2
IN
VL
S1
VOUT2
V+
+5V +15V
CL2
VS1 = +10V
VS2 = +10V RL1
VOUT1
CL1
RL = 300Ω
CL = 35pF
D1
D2
SWITCH
OUTPUT 1
(VO1)
DG413
Figure 2. Switching-Time
Figure 3. DG413 Break-Before-Make
______________________________________________Timing Diagrams/Test Circuits
VGEN GND
D
CL
VOUT
-15V
V-
V+
VOUT
IN OFF ON OFF
∆VOUT
Q = (∆VOUT)(CL)
S
+5V
IN DEPENDS ON SWITCH CONFIGURATION;
INPUT POLARITY DETERMINED BY SENSE OF SWITCH.
OFF ON OFF
IN
VIN = +3V
+15V
RGEN
IN
VL
DG411
DG412
DG413
Figure 4. Charge-Injection
DG411/DG412/DG413
Improved, Quad,
SPST Analog Switches
8_______________________________________________________________________________________
Figure 6. Crosstalk
IN
0V or
2.4V
SIGNAL
GENERATOR
+15V
C
VL
ANALYZER D
RL
GND
S
C
-15V
V-
+5V
V+
DG411
DG412
DG413
SIGNAL
GENERATOR 0dBm
+15V
C
ANALYZER D
RL
GND
S
C
V-
-15V
0V or 2.4V IN1
D50Ω
VL
S
+5V
IN2
0V or 2.4V
V+
DG411
DG412
DG413
Figure 5. Off-Isolation
_________________________________Timing Diagrams/Test Circuits (continued)
CAPACITANCE
METER
D
S
GND C
V-
-15V
IN 0V or
2.4V
C+15V
VL
+5V
f = 1MHz
V+
DG411
DG412
DG413
CAPACITANCE
METER
D
S
GND C
V-
-15V
IN 0V or
2.4V
C+15V
VL
+5V
f = 1MHz
V+
DG411
DG412
DG413
Figure 7. Channel Off-Capacitance Figure 8. Channel On-Capacitance
DG411/DG412/DG413
Improved, Quad,
SPST Analog Switches
_______________________________________________________________________________________ 9
__Ordering Information (continued) ___________________Chip Topography
S3
S4
D3
0.097"
(2.46mm)
0.080"
(2.03mm)
V-
GND
D4
IN4 IN3
VL
V+
S2
D1 IN1 IN2
S1
D2
TRANSISTOR COUNT: 136
SUBSTRATE CONNECTED TO V+
* Contact factory for dice specifications.
**Contact factory for availability and processing to MIL-STD-883B.
16
D1
15
IN1
14
IN2
13
D2
5
D4
6
IN4
7
IN3
8
D3
DG411
2V-
1S1
3GND
4
S4
11 V+
12 S2
10 VL
9S3
TOP VIEW
16
D1
15
IN1
14
IN2
13
D2
5
D4
6
IN4
7
IN3
8
D3
DG412
2V-
1S1
3GND
4
S4
11 V+
12 S2
10 VL
9S3
16
D1
15
IN1
14
IN2
13
D2
5
D4
6
IN4
7
IN3
8
D3
DG413
2V-
1S1
3GND
4
S4
11 V+
12 S2
10 VL
9S3
QFNQFN QFN
______________________Pin Configurations/Functional Diagrams (continued)
PART TEMP RANGE PIN-PACKAGE
DG411EGE
DG411DJ
DG411DY
DG411DK
DG411AK
DG412CJ
DG412CUE
DG412CY
DG412C/D
DG412DJ
DG412EGE
DG412DY
DG412DK
DG412AK
DG413CJ
DG413CUE
DG413CY
DG413C/D
DE413EGE
DG413DJ
DG413DY
DG413DK
DG413AK -55°C to +125°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
-55°C to +125°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
0°C to +70°C
-55°C to +125°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C 16 QFN
16 Plastic DIP
16 Narrow SO
16 CERDIP
16 CERDIP**
16 Plastic DIP
16 TSSOP
16 Narrow SO
Dice*
16 Plastic DIP
16 QFN
16 Narrow SO
16 CERDIP
16 CERDIP**
16 Plastic DIP
16 TSSOP
16 Narrow SO
Dice*
16 QFN
16 Plastic DIP
16 Narrow SO
16 CERDIP
16 CERDIP**
DG411/DG412/DG413
Improved, Quad,
SPST Analog Switches
10 ______________________________________________________________________________________
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
DG411/DG412/DG413
Improved, Quad,
SPST Analog Switches
______________________________________________________________________________________ 11
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
DG411/DG412/DG413
Improved, Quad,
SPST Analog Switches
12 ______________________________________________________________________________________
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
DG411/DG412/DG413
Improved, Quad,
SPST Analog Switches
______________________________________________________________________________________ 13
TSSOP4.40mm.EPS
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
14 __________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600
©2004 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.
DG411/DG412/DG413
Improved, Quad,
SPST Analog Switches
32L QFN.EPS
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)