November 2017
INDUCTORS
MHQ0603P 0603 [0201 inch]*
* Dimensions code: JIS[EIA]
Inductors for high frequency circuits
Multilayer ceramic
MHQ0603P
type
MHQ-P series (for automotive)
(2/16)
20171113 / inductor_automotive_high-frequency_mhq0603p_en.fm
INDUCTORS
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using this products.
The storage period is less than 12 months. Be sure to follow the storage conditions (temperature: 5 to 40°C, humidity: 10 to 75% RH or
less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equip-
ment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equip-
ment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or qual-
ity require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society,
person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/aviation equipment
(2) Transportation equipment (electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment  
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing pro-
tection circuit/device or providing backup circuits in your equipment.
REMINDERS
(3/16)
20171113 / inductor_automotive_high-frequency_mhq0603p_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
INDUCTORS
Inductors for high frequency circuits
Multilayer ceramic
FEATURES
Unique ceramic material and configuration allows for the realization of high Q characteristics that are equivalent to that of air core wound
inductors.
Multilayer method allows for a lineup with fine increments of inductance.
APPLICATION
Automotive equipment, smart phones, tablet terminals, high frequency modules (PAs, VCOs, FEMs , etc.), Bluetooth, W-LAN, UWB, tuners
and other high frequency circuits for the mobile communication industry
PART NUMBER CONSTRUCTION
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
The storage temperature range is for after the circuit board is mounted.
Overview of MHQ0603P type
MHQ 0603 P 0N6 B T D25
Series name L×W×H dimensions Characteristics Inductance Inductance
tolerance Packaging style Internal code
(mm) (nH)
0603 0.65×0.35×0.35 P 0N6 0.6 B ±0.1nH T Taping D25
1N1 1.1 C ±0.2nH
11N 11 S ±0.3nH
H±3%
J±5%
Type
Temperature range Package quantity Individual weight
Operating
temperature
(°C)
Storage
temperature
(°C) (pieces/reel) （mg）
MHQ0603P –55 to +125 –55 to +125 15000 0.2
Product compatible with RoHS directive
Halogen-free
Compatible with lead-free solders
AEC-Q200
RoHS Directive Compliant Product: See the following for more details.https://product.tdk.com/info/en/environment/rohs/index.html
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
(4/16)
20171113 / inductor_automotive_high-frequency_mhq0603p_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
INDUCTORS
MHQ0603P type
RECOMMENDED REFLOW PROFILE
Preheating Soldering Peak
Temp. Time Temp. Time Temp. Time
T1 T2 t1 T3 t2 T4 t3
150°C 180°C 60 to 120s 230°C 30 to 60s 250 to 260°C 10s max.
Natural
cooling
t3
t1
Preheating
t2
Soldering
T3 T3
T4
T2
T1
t: Time
Peak
T: Temperature
(5/16)
20171113 / inductor_automotive_high-frequency_mhq0603p_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
INDUCTORS
MHQ0603P type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
Dimensions in mm
0.15±0.050.15±0.05
0.65±0.05
0.09±0.04 0.09±0.04
0.35±0.050.35±0.05
Dimensions in mm
(6/16)
20171113 / inductor_automotive_high-frequency_mhq0603p_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
INDUCTORS
MHQ0603P type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
・Short bar residual inductance =0.48nH
○Measurement equipment
＊Equivalent measurement equipment may be used.
LL measuring
frequency
QQ measuring
frequency
Self-resonant
frequency
DC resistance Rated current Part No.
(nH) Tolerance (MHz) min. (MHz) (GHz)min. (GHz)typ. ()max. ()typ. (mA)max.
0.6 ±0.1nH 500 — 500 10.0 20.0 0.07 0.02 1000 MHQ0603P0N6BTD25
0.6 ±0.2nH 500 —500 10.0 20.0 0.07 0.02 1000 MHQ0603P0N6CTD25
0.7 ±0.1nH 500 — 500 10.0 20.0 0.07 0.02 1000 MHQ0603P0N7BTD25
0.7 ±0.2nH 500 —500 10.0 20.0 0.07 0.02 1000 MHQ0603P0N7CTD25
0.8 ±0.1nH 500 — 500 10.0 20.0 0.07 0.02 1000 MHQ0603P0N8BTD25
0.8 ±0.2nH 500 —500 10.0 20.0 0.07 0.02 1000 MHQ0603P0N8CTD25
0.9 ±0.1nH 500 — 500 10.0 18.8 0.07 0.02 1000 MHQ0603P0N9BTD25
0.9 ±0.2nH 500 —500 10.0 18.8 0.07 0.02 1000 MHQ0603P0N9CTD25
1.0 ±0.1nH 500 — 500 10.0 19.3 0.07 0.03 1000 MHQ0603P1N0BTD25
1.0 ±0.2nH 500 —500 10.0 19.3 0.07 0.03 1000 MHQ0603P1N0CTD25
1.0 ±0.3nH 500 — 500 10.0 19.3 0.07 0.03 1000 MHQ0603P1N0STD25
1.1 ±0.1nH 500 —500 10.0 19.3 0.07 0.03 1000 MHQ0603P1N1BTD25
1.1 ±0.2nH 500 — 500 10.0 19.3 0.07 0.03 1000 MHQ0603P1N1CTD25
1.1 ±0.3nH 500 —500 10.0 19.3 0.07 0.03 1000 MHQ0603P1N1STD25
1.2 ±0.1nH 500 — 500 10.0 20.0 0.08 0.04 1000 MHQ0603P1N2BTD25
1.2 ±0.2nH 500 —500 10.0 20.0 0.08 0.04 1000 MHQ0603P1N2CTD25
1.2 ±0.3nH 500 — 500 10.0 20.0 0.08 0.04 1000 MHQ0603P1N2STD25
1.3 ±0.1nH 500 —500 10.0 20.0 0.10 0.06 800 MHQ0603P1N3BTD25
1.3 ±0.2nH 500 — 500 10.0 20.0 0.10 0.06 800 MHQ0603P1N3CTD25
1.3 ±0.3nH 500 —500 10.0 20.0 0.10 0.06 800 MHQ0603P1N3STD25
1.4 ±0.1nH 500 — 500 10.0 18.6 0.10 0.06 800 MHQ0603P1N4BTD25
1.4 ±0.2nH 500 —500 10.0 18.6 0.10 0.06 800 MHQ0603P1N4CTD25
1.4 ±0.3nH 500 — 500 10.0 18.6 0.10 0.06 800 MHQ0603P1N4STD25
1.5 ±0.1nH 500 16 500 10.0 19.5 0.10 0.05 800 MHQ0603P1N5BTD25
1.5 ±0.2nH 500 16 500 10.0 19.5 0.10 0.05 800 MHQ0603P1N5CTD25
1.5 ±0.3nH 500 16 500 10.0 19.5 0.10 0.05 800 MHQ0603P1N5STD25
1.6 ±0.1nH 500 16 500 10.0 17.5 0.10 0.06 800 MHQ0603P1N6BTD25
1.6 ±0.2nH 500 16 500 10.0 17.5 0.10 0.06 800 MHQ0603P1N6CTD25
1.6 ±0.3nH 500 16 500 10.0 17.5 0.10 0.06 800 MHQ0603P1N6STD25
1.7 ±0.1nH 500 16 500 10.0 16.7 0.10 0.07 800 MHQ0603P1N7BTD25
1.7 ±0.2nH 500 16 500 10.0 16.7 0.10 0.07 800 MHQ0603P1N7CTD25
1.7 ±0.3nH 500 16 500 10.0 16.7 0.10 0.07 800 MHQ0603P1N7STD25
1.8 ±0.1nH 500 16 500 10.0 15.8 0.12 0.07 700 MHQ0603P1N8BTD25
1.8 ±0.2nH 500 16 500 10.0 15.8 0.12 0.07 700 MHQ0603P1N8CTD25
1.8 ±0.3nH 500 16 500 10.0 15.8 0.12 0.07 700 MHQ0603P1N8STD25
1.9 ±0.1nH 500 16 500 10.0 16.1 0.12 0.08 700 MHQ0603P1N9BTD25
1.9 ±0.2nH 500 16 500 10.0 16.1 0.12 0.08 700 MHQ0603P1N9CTD25
1.9 ±0.3nH 500 16 500 10.0 16.1 0.12 0.08 700 MHQ0603P1N9STD25
2.0 ±0.1nH 500 16 500 10.0 13.8 0.12 0.08 700 MHQ0603P2N0BTD25
2.0 ±0.2nH 500 16 500 10.0 13.8 0.12 0.08 700 MHQ0603P2N0CTD25
2.0 ±0.3nH 500 16 500 10.0 13.8 0.12 0.08 700 MHQ0603P2N0STD25
2.1 ±0.1nH 500 16 500 10.0 12.7 0.15 0.08 700 MHQ0603P2N1BTD25
2.1 ±0.2nH 500 16 500 10.0 12.7 0.15 0.08 700 MHQ0603P2N1CTD25
2.1 ±0.3nH 500 16 500 10.0 12.7 0.15 0.08 700 MHQ0603P2N1STD25
Measurement item Product No. Manufacturer
L, Q 4991A+16197A Keysight Technologies
Self-resonant frequency 8720C Keysight Technologies
DC resistance Type-7561 Yokogawa
(7/16)
20171113 / inductor_automotive_high-frequency_mhq0603p_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
INDUCTORS
MHQ0603P type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
・Short bar residual inductance =0.48nH
○Measurement equipment
＊Equivalent measurement equipment may be used.
LL measuring
frequency
QQ measuring
frequency
Self-resonant
frequency
DC resistance Rated current Part No.
(nH) Tolerance (MHz) min. (MHz) (GHz)min. (GHz)typ. ()max. ()typ. (mA)max.
2.2 ±0.1nH 500 16 500 10.0 13.2 0.15 0.09 700 MHQ0603P2N2BTD25
2.2 ±0.2nH 500 16 500 10.0 13.2 0.15 0.09 700 MHQ0603P2N2CTD25
2.2 ±0.3nH 500 16 500 10.0 13.2 0.15 0.09 700 MHQ0603P2N2STD25
2.3 ±0.1nH 500 16 500 10.0 12.5 0.15 0.08 700 MHQ0603P2N3BTD25
2.3 ±0.2nH 500 16 500 10.0 12.5 0.15 0.08 700 MHQ0603P2N3CTD25
2.3 ±0.3nH 500 16 500 10.0 12.5 0.15 0.08 700 MHQ0603P2N3STD25
2.4 ±0.1nH 500 16 500 8.0 11.7 0.15 0.08 700 MHQ0603P2N4BTD25
2.4 ±0.2nH 500 16 500 8.0 11.7 0.15 0.08 700 MHQ0603P2N4CTD25
2.4 ±0.3nH 500 16 500 8.0 11.7 0.15 0.08 700 MHQ0603P2N4STD25
2.5 ±0.1nH 500 16 500 8.0 11.1 0.25 0.17 500 MHQ0603P2N5BTD25
2.5 ±0.2nH 500 16 500 8.0 11.1 0.25 0.17 500 MHQ0603P2N5CTD25
2.5 ±0.3nH 500 16 500 8.0 11.1 0.25 0.17 500 MHQ0603P2N5STD25
2.6 ±0.1nH 500 16 500 8.0 11.1 0.25 0.16 500 MHQ0603P2N6BTD25
2.6 ±0.2nH 500 16 500 8.0 11.1 0.25 0.16 500 MHQ0603P2N6CTD25
2.6 ±0.3nH 500 16 500 8.0 11.1 0.25 0.16 500 MHQ0603P2N6STD25
2.7 ±0.1nH 500 16 500 8.0 10.5 0.25 0.16 500 MHQ0603P2N7BTD25
2.7 ±0.2nH 500 16 500 8.0 10.5 0.25 0.16 500 MHQ0603P2N7CTD25
2.7 ±0.3nH 500 16 500 8.0 10.5 0.25 0.16 500 MHQ0603P2N7STD25
2.8 ±0.1nH 500 16 500 8.0 10.6 0.25 0.18 500 MHQ0603P2N8BTD25
2.8 ±0.2nH 500 16 500 8.0 10.6 0.25 0.18 500 MHQ0603P2N8CTD25
2.8 ±0.3nH 500 16 500 8.0 10.6 0.25 0.18 500 MHQ0603P2N8STD25
2.9 ±0.1nH 500 16 500 8.0 10.8 0.30 0.19 450 MHQ0603P2N9BTD25
2.9 ±0.2nH 500 16 500 8.0 10.8 0.30 0.19 450 MHQ0603P2N9CTD25
2.9 ±0.3nH 500 16 500 8.0 10.8 0.30 0.19 450 MHQ0603P2N9STD25
3.0 ±0.1nH 500 16 500 8.0 10.3 0.30 0.19 450 MHQ0603P3N0BTD25
3.0 ±0.2nH 500 16 500 8.0 10.3 0.30 0.19 450 MHQ0603P3N0CTD25
3.0 ±0.3nH 500 16 500 8.0 10.3 0.30 0.19 450 MHQ0603P3N0STD25
3.1 ±0.1nH 500 16 500 8.0 10.5 0.30 0.19 450 MHQ0603P3N1BTD25
3.1 ±0.2nH 500 16 500 8.0 10.5 0.30 0.19 450 MHQ0603P3N1CTD25
3.1 ±0.3nH 500 16 500 8.0 10.5 0.30 0.19 450 MHQ0603P3N1STD25
3.2 ±0.1nH 500 16 500 7.0 9.5 0.20 0.13 550 MHQ0603P3N2BTD25
3.2 ±0.2nH 500 16 500 7.0 9.5 0.20 0.13 550 MHQ0603P3N2CTD25
3.2 ±0.3nH 500 16 500 7.0 9.5 0.20 0.13 550 MHQ0603P3N2STD25
3.3 ±0.1nH 500 16 500 7.0 9.6 0.25 0.15 500 MHQ0603P3N3BTD25
3.3 ±0.2nH 500 16 500 7.0 9.6 0.25 0.15 500 MHQ0603P3N3CTD25
3.3 ±0.3nH 500 16 500 7.0 9.6 0.25 0.15 500 MHQ0603P3N3STD25
3.4 ±0.1nH 500 16 500 6.5 9.3 0.25 0.14 500 MHQ0603P3N4BTD25
3.4 ±0.2nH 500 16 500 6.5 9.3 0.25 0.14 500 MHQ0603P3N4CTD25
3.4 ±0.3nH 500 16 500 6.5 9.3 0.25 0.14 500 MHQ0603P3N4STD25
3.5 ±0.1nH 500 16 500 6.5 9.5 0.25 0.17 500 MHQ0603P3N5BTD25
3.5 ±0.2nH 500 16 500 6.5 9.5 0.25 0.17 500 MHQ0603P3N5CTD25
3.5 ±0.3nH 500 16 500 6.5 9.5 0.25 0.17 500 MHQ0603P3N5STD25
3.6 ±0.1nH 500 16 500 6.5 9.1 0.25 0.16 500 MHQ0603P3N6BTD25
3.6 ±0.2nH 500 16 500 6.5 9.1 0.25 0.16 500 MHQ0603P3N6CTD25
3.6 ±0.3nH 500 16 500 6.5 9.1 0.25 0.16 500 MHQ0603P3N6STD25
Measurement item Product No. Manufacturer
L, Q 4991A+16197A Keysight Technologies
Self-resonant frequency 8720C Keysight Technologies
DC resistance Type-7561 Yokogawa
(8/16)
20171113 / inductor_automotive_high-frequency_mhq0603p_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
INDUCTORS
MHQ0603P type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
・Short bar residual inductance =0.48nH
○Measurement equipment
＊Equivalent measurement equipment may be used.
LL measuring
frequency
QQ measuring
frequency
Self-resonant
frequency
DC resistance Rated current Part No.
(nH) Tolerance (MHz) min. (MHz) (GHz)min. (GHz)typ. ()max. ()typ. (mA)max.
3.7 ±0.1nH 500 16 500 6.5 9.1 0.25 0.17 450 MHQ0603P3N7BTD25
3.7 ±0.2nH 500 16 500 6.5 9.1 0.25 0.17 450 MHQ0603P3N7CTD25
3.7 ±0.3nH 500 16 500 6.5 9.1 0.25 0.17 450 MHQ0603P3N7STD25
3.8 ±0.1nH 500 16 500 6.5 9.1 0.30 0.19 450 MHQ0603P3N8BTD25
3.8 ±0.2nH 500 16 500 6.5 9.1 0.30 0.19 450 MHQ0603P3N8CTD25
3.8 ±0.3nH 500 16 500 6.5 9.1 0.30 0.19 450 MHQ0603P3N8STD25
3.9 ±0.1nH 500 16 500 6.5 9.2 0.35 0.23 400 MHQ0603P3N9BTD25
3.9 ±0.2nH 500 16 500 6.5 9.2 0.35 0.23 400 MHQ0603P3N9CTD25
3.9 ±0.3nH 500 16 500 6.5 9.2 0.35 0.23 400 MHQ0603P3N9STD25
4.0 ±0.1nH 500 16 500 6.0 8.5 0.35 0.26 400 MHQ0603P4N0BTD25
4.0 ±0.2nH 500 16 500 6.0 8.5 0.35 0.26 400 MHQ0603P4N0CTD25
4.0 ±0.3nH 500 16 500 6.0 8.5 0.35 0.26 400 MHQ0603P4N0STD25
4.1 ±0.1nH 500 16 500 6.0 8.3 0.35 0.22 400 MHQ0603P4N1BTD25
4.1 ±0.2nH 500 16 500 6.0 8.3 0.35 0.22 400 MHQ0603P4N1CTD25
4.1 ±0.3nH 500 16 500 6.0 8.3 0.35 0.22 400 MHQ0603P4N1STD25
4.2 ±0.1nH 500 16 500 6.0 8.2 0.35 0.23 400 MHQ0603P4N2BTD25
4.2 ±0.2nH 500 16 500 6.0 8.2 0.35 0.23 400 MHQ0603P4N2CTD25
4.2 ±0.3nH 500 16 500 6.0 8.2 0.35 0.23 400 MHQ0603P4N2STD25
4.3 ±0.2nH 500 16 500 6.0 8.2 0.35 0.23 400 MHQ0603P4N3CTD25
4.3 ±0.3nH 500 16 500 6.0 8.2 0.35 0.23 400 MHQ0603P4N3STD25
4.3 ±3% 500 16 500 6.0 8.2 0.35 0.23 400 MHQ0603P4N3HTD25
4.7 ±0.2nH 500 16 500 5.5 7.9 0.40 0.25 350 MHQ0603P4N7CTD25
4.7 ±0.3nH 500 16 500 5.5 7.9 0.40 0.25 350 MHQ0603P4N7STD25
4.7 ±3% 500 16 500 5.5 7.9 0.40 0.25 350 MHQ0603P4N7HTD25
5.1 ±0.2nH 500 16 500 5.5 7.8 0.40 0.24 350 MHQ0603P5N1CTD25
5.1 ±0.3nH 500 16 500 5.5 7.8 0.40 0.24 350 MHQ0603P5N1STD25
5.1 ±3% 500 16 500 5.5 7.8 0.40 0.24 350 MHQ0603P5N1HTD25
5.6 ±0.2nH 500 16 500 5.0 7.1 0.40 0.29 350 MHQ0603P5N6CTD25
5.6 ±0.3nH 500 16 500 5.0 7.1 0.40 0.29 350 MHQ0603P5N6STD25
5.6 ±3% 500 16 500 5.0 7.1 0.40 0.29 350 MHQ0603P5N6HTD25
6.2 ±0.3nH 500 16 500 4.0 6.7 0.70 0.52 300 MHQ0603P6N2STD25
6.2 ±3% 500 16 500 4.0 6.7 0.70 0.52 300 MHQ0603P6N2HTD25
6.8 ±3% 500 16 500 4.0 6.8 0.70 0.53 300 MHQ0603P6N8HTD25
6.8 ±5% 500 16 500 4.0 6.8 0.70 0.53 300 MHQ0603P6N8JTD25
7.5 ±3% 500 16 500 3.8 5.7 0.50 0.37 300 MHQ0603P7N5HTD25
7.5 ±5% 500 16 500 3.8 5.7 0.50 0.37 300 MHQ0603P7N5JTD25
8.2 ±3% 500 16 500 3.8 5.4 0.90 0.64 250 MHQ0603P8N2HTD25
8.2 ±5% 500 16 500 3.8 5.4 0.90 0.64 250 MHQ0603P8N2JTD25
9.1 ±3% 500 16 500 3.8 5.5 0.90 0.62 250 MHQ0603P9N1HTD25
9.1 ±5% 500 16 500 3.8 5.5 0.90 0.62 250 MHQ0603P9N1JTD25
10 ±3% 500 16 500 3.5 5.2 1.20 0.86 240 MHQ0603P10NHTD25
10 ±5% 500 16 500 3.5 5.2 1.20 0.86 240 MHQ0603P10NJTD25
11 ±3% 500 16 500 3.2 4.6 1.30 0.89 240 MHQ0603P11NHTD25
11 ±5% 500 16 500 3.2 4.6 1.30 0.89 240 MHQ0603P11NJTD25
Measurement item Product No. Manufacturer
L, Q 4991A+16197A Keysight Technologies
Self-resonant frequency 8720C Keysight Technologies
DC resistance Type-7561 Yokogawa
(9/16)
20171113 / inductor_automotive_high-frequency_mhq0603p_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
INDUCTORS
MHQ0603P type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
・Short bar residual inductance =0.48nH
○Measurement equipment
＊Equivalent measurement equipment may be used.
LL measuring
frequency
QQ measuring
frequency
Self-resonant
frequency
DC resistance Rated current Part No.
(nH) Tolerance (MHz) min. (MHz) (GHz)min. (GHz)typ. ()max. ()typ. (mA)max.
12 ±3% 500 16 500 3.2 4.6 1.40 0.77 240 MHQ0603P12NHTD25
12 ±5% 500 16 500 3.2 4.6 1.40 0.77 240 MHQ0603P12NJTD25
13 ±3% 500 16 500 3.2 4.5 1.50 1.01 180 MHQ0603P13NHTD25
13 ±5% 500 16 500 3.2 4.5 1.50 1.01 180 MHQ0603P13NJTD25
15 ±3% 500 16 500 2.8 4.2 1.50 1.05 180 MHQ0603P15NHTD25
15 ±5% 500 16 500 2.8 4.2 1.50 1.05 180 MHQ0603P15NJTD25
16 ±3% 500 16 500 2.5 4.0 1.70 1.21 180 MHQ0603P16NHTD25
16 ±5% 500 16 500 2.5 4.0 1.70 1.21 180 MHQ0603P16NJTD25
18 ±3% 500 16 500 2.4 3.7 1.70 1.21 180 MHQ0603P18NHTD25
18 ±5% 500 16 500 2.4 3.7 1.70 1.21 180 MHQ0603P18NJTD25
20 ±3% 500 16 500 2.4 3.5 2.00 1.38 160 MHQ0603P20NHTD25
20 ±5% 500 16 500 2.4 3.5 2.00 1.38 160 MHQ0603P20NJTD25
22 ±3% 500 16 500 2.2 3.3 2.00 1.40 160 MHQ0603P22NHTD25
22 ±5% 500 16 500 2.2 3.3 2.00 1.40 160 MHQ0603P22NJTD25
24 ±3% 500 16 500 2.1 3.1 2.20 1.55 160 MHQ0603P24NHTD25
24 ±5% 500 16 500 2.1 3.1 2.20 1.55 160 MHQ0603P24NJTD25
27 ±3% 500 16 500 2.0 2.9 2.20 1.55 160 MHQ0603P27NHTD25
27 ±5% 500 16 500 2.0 2.9 2.20 1.55 160 MHQ0603P27NJTD25
30 ±3% 500 16 500 1.9 2.7 2.70 1.98 160 MHQ0603P30NHTD25
30 ±5% 500 16 500 1.9 2.7 2.70 1.98 160 MHQ0603P30NJTD25
33 ±3% 300 14 300 1.8 2.5 2.80 2.06 160 MHQ0603P33NHTD25
33 ±5% 300 14 300 1.8 2.5 2.80 2.06 160 MHQ0603P33NJTD25
36 ±3% 300 14 300 1.7 2.4 2.80 2.08 160 MHQ0603P36NHTD25
36 ±5% 300 14 300 1.7 2.4 2.80 2.08 160 MHQ0603P36NJTD25
39 ±3% 300 14 300 1.6 2.3 3.00 2.24 160 MHQ0603P39NHTD25
39 ±5% 300 14 300 1.6 2.3 3.00 2.24 160 MHQ0603P39NJTD25
Measurement item Product No. Manufacturer
L, Q 4991A+16197A Keysight Technologies
Self-resonant frequency 8720C Keysight Technologies
DC resistance Type-7561 Yokogawa
(10/16)
20171113 / inductor_automotive_high-frequency_mhq0603p_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
INDUCTORS
MHQ0603P type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
○Measurement equipment
＊Equivalent measurement equipment may be used.
L(nH)typ. Q typ. Part No.
500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz 500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz
0.6 0.6 0.6 0.6 0.6 29min. 38min. 58min. 60min. 66min. MHQ0603P0N6BTD25
0.6 0.6 0.6 0.6 0.6 29min. 38min. 58min. 60min. 66min. MHQ0603P0N6CTD25
0.7 0.7 0.7 0.7 0.7 29min. 38min. 58min. 60min. 66min. MHQ0603P0N7BTD25
0.7 0.7 0.7 0.7 0.7 29min. 38min. 58min. 60min. 66min. MHQ0603P0N7CTD25
0.8 0.8 0.8 0.8 0.8 29min. 38min. 58min. 60min. 66min. MHQ0603P0N8BTD25
0.8 0.8 0.8 0.8 0.8 29min. 38min. 58min. 60min. 66min. MHQ0603P0N8CTD25
0.9 0.9 0.9 0.9 0.9 29min. 38min. 58min. 60min. 66min. MHQ0603P0N9BTD25
0.9 0.9 0.9 0.9 0.9 29min. 38min. 58min. 60min. 66min. MHQ0603P0N9CTD25
1.0 1.0 1.0 1.0 1.0 29min. 38min. 58min. 60min. 66min. MHQ0603P1N0BTD25
1.0 1.0 1.0 1.0 1.0 29min. 38min. 58min. 60min. 66min. MHQ0603P1N0CTD25
1.0 1.0 1.0 1.0 1.0 29min. 38min. 58min. 60min. 66min. MHQ0603P1N0STD25
1.1 1.1 1.1 1.1 1.1 29min. 38min. 58min. 60min. 66min. MHQ0603P1N1BTD25
1.1 1.1 1.1 1.1 1.1 29min. 38min. 58min. 60min. 66min. MHQ0603P1N1CTD25
1.1 1.1 1.1 1.1 1.1 29min. 38min. 58min. 60min. 66min. MHQ0603P1N1STD25
1.2 1.2 1.2 1.2 1.2 29min. 38min. 58min. 60min. 66min. MHQ0603P1N2BTD25
1.2 1.2 1.2 1.2 1.2 29min. 38min. 58min. 60min. 66min. MHQ0603P1N2CTD25
1.2 1.2 1.2 1.2 1.2 29min. 38min. 58min. 60min. 66min. MHQ0603P1N2STD25
1.3 1.3 1.3 1.3 1.3 29min. 38min. 58min. 60min. 66min. MHQ0603P1N3BTD25
1.3 1.3 1.3 1.3 1.3 29min. 38min. 58min. 60min. 66min. MHQ0603P1N3CTD25
1.3 1.3 1.3 1.3 1.3 29min. 38min. 58min. 60min. 66min. MHQ0603P1N3STD25
1.4 1.4 1.4 1.4 1.4 29min. 38min. 58min. 60min. 66min. MHQ0603P1N4BTD25
1.4 1.4 1.4 1.4 1.4 29min. 38min. 58min. 60min. 66min. MHQ0603P1N4CTD25
1.4 1.4 1.4 1.4 1.4 29min. 38min. 58min. 60min. 66min. MHQ0603P1N4STD25
1.5 1.5 1.5 1.5 1.5 29 38 58 60 66 MHQ0603P1N5BTD25
1.5 1.5 1.5 1.5 1.5 29 38 58 60 66 MHQ0603P1N5CTD25
1.5 1.5 1.5 1.5 1.5 29 38 58 60 66 MHQ0603P1N5STD25
1.6 1.6 1.6 1.6 1.6 28 37 56 60 66 MHQ0603P1N6BTD25
1.6 1.6 1.6 1.6 1.6 28 37 56 60 66 MHQ0603P1N6CTD25
1.6 1.6 1.6 1.6 1.6 28 37 56 60 66 MHQ0603P1N6STD25
1.7 1.7 1.7 1.7 1.7 30 39 62 65 71 MHQ0603P1N7BTD25
1.7 1.7 1.7 1.7 1.7 30 39 62 65 71 MHQ0603P1N7CTD25
1.7 1.7 1.7 1.7 1.7 30 39 62 65 71 MHQ0603P1N7STD25
1.8 1.8 1.8 1.8 1.8 29 38 59 62 69 MHQ0603P1N8BTD25
1.8 1.8 1.8 1.8 1.8 29 38 59 62 69 MHQ0603P1N8CTD25
1.8 1.8 1.8 1.8 1.8 29 38 59 62 69 MHQ0603P1N8STD25
1.9 1.9 1.9 1.9 1.9 28 38 57 60 66 MHQ0603P1N9BTD25
1.9 1.9 1.9 1.9 1.9 28 38 57 60 66 MHQ0603P1N9CTD25
1.9 1.9 1.9 1.9 1.9 28 38 57 60 66 MHQ0603P1N9STD25
2.0 2.0 2.0 2.0 2.0 27 35 55 58 64 MHQ0603P2N0BTD25
2.0 2.0 2.0 2.0 2.0 27 35 55 58 64 MHQ0603P2N0CTD25
2.0 2.0 2.0 2.0 2.0 27 35 55 58 64 MHQ0603P2N0STD25
2.1 2.1 2.1 2.1 2.2 29 37 58 62 68 MHQ0603P2N1BTD25
2.1 2.1 2.1 2.1 2.2 29 37 58 62 68 MHQ0603P2N1CTD25
2.1 2.1 2.1 2.1 2.2 29 37 58 62 68 MHQ0603P2N1STD25
Product No. Manufacturer
4291B+16193A Keysight Technologies
(11/16)
20171113 / inductor_automotive_high-frequency_mhq0603p_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
INDUCTORS
MHQ0603P type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
○Measurement equipment
＊Equivalent measurement equipment may be used.
L(nH)typ. Q typ. Part No.
500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz 500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz
2.2 2.2 2.2 2.2 2.3 28 37 57 61 68 MHQ0603P2N2BTD25
2.2 2.2 2.2 2.2 2.3 28 37 57 61 68 MHQ0603P2N2CTD25
2.2 2.2 2.2 2.2 2.3 28 37 57 61 68 MHQ0603P2N2STD25
2.3 2.3 2.3 2.3 2.4 31 40 61 64 71 MHQ0603P2N3BTD25
2.3 2.3 2.3 2.3 2.4 31 40 61 64 71 MHQ0603P2N3CTD25
2.3 2.3 2.3 2.3 2.4 31 40 61 64 71 MHQ0603P2N3STD25
2.4 2.4 2.4 2.4 2.5 31 41 62 64 71 MHQ0603P2N4BTD25
2.4 2.4 2.4 2.4 2.5 31 41 62 64 71 MHQ0603P2N4CTD25
2.4 2.4 2.4 2.4 2.5 31 41 62 64 71 MHQ0603P2N4STD25
2.5 2.5 2.5 2.6 2.6 25 32 51 53 59 MHQ0603P2N5BTD25
2.5 2.5 2.5 2.6 2.6 25 32 51 53 59 MHQ0603P2N5CTD25
2.5 2.5 2.5 2.6 2.6 25 32 51 53 59 MHQ0603P2N5STD25
2.6 2.6 2.6 2.7 2.7 26 34 54 56 62 MHQ0603P2N6BTD25
2.6 2.6 2.6 2.7 2.7 26 34 54 56 62 MHQ0603P2N6CTD25
2.6 2.6 2.6 2.7 2.7 26 34 54 56 62 MHQ0603P2N6STD25
2.7 2.7 2.7 2.8 2.8 26 34 54 57 63 MHQ0603P2N7BTD25
2.7 2.7 2.7 2.8 2.8 26 34 54 57 63 MHQ0603P2N7CTD25
2.7 2.7 2.7 2.8 2.8 26 34 54 57 63 MHQ0603P2N7STD25
2.8 2.8 2.8 2.9 2.9 26 35 54 55 62 MHQ0603P2N8BTD25
2.8 2.8 2.8 2.9 2.9 26 35 54 55 62 MHQ0603P2N8CTD25
2.8 2.8 2.8 2.9 2.9 26 35 54 55 62 MHQ0603P2N8STD25
2.9 2.9 2.9 3.0 3.0 24 31 48 51 56 MHQ0603P2N9BTD25
2.9 2.9 2.9 3.0 3.0 24 31 48 51 56 MHQ0603P2N9CTD25
2.9 2.9 2.9 3.0 3.0 24 31 48 51 56 MHQ0603P2N9STD25
3.0 3.0 3.0 3.1 3.1 23 30 46 48 52 MHQ0603P3N0BTD25
3.0 3.0 3.0 3.1 3.1 23 30 46 48 52 MHQ0603P3N0CTD25
3.0 3.0 3.0 3.1 3.1 23 30 46 48 52 MHQ0603P3N0STD25
3.1 3.1 3.2 3.2 3.2 24 32 49 51 57 MHQ0603P3N1BTD25
3.1 3.1 3.2 3.2 3.2 24 32 49 51 57 MHQ0603P3N1CTD25
3.1 3.1 3.2 3.2 3.2 24 32 49 51 57 MHQ0603P3N1STD25
3.2 3.2 3.3 3.3 3.4 27 35 53 55 61 MHQ0603P3N2BTD25
3.2 3.2 3.3 3.3 3.4 27 35 53 55 61 MHQ0603P3N2CTD25
3.2 3.2 3.3 3.3 3.4 27 35 53 55 61 MHQ0603P3N2STD25
3.3 3.3 3.4 3.4 3.5 25 32 48 50 54 MHQ0603P3N3BTD25
3.3 3.3 3.4 3.4 3.5 25 32 48 50 54 MHQ0603P3N3CTD25
3.3 3.3 3.4 3.4 3.5 25 32 48 50 54 MHQ0603P3N3STD25
3.4 3.4 3.5 3.5 3.6 27 35 53 55 61 MHQ0603P3N4BTD25
3.4 3.4 3.5 3.5 3.6 27 35 53 55 61 MHQ0603P3N4CTD25
3.4 3.4 3.5 3.5 3.6 27 35 53 55 61 MHQ0603P3N4STD25
3.5 3.5 3.6 3.6 3.7 25 33 50 52 57 MHQ0603P3N5BTD25
3.5 3.5 3.6 3.6 3.7 25 33 50 52 57 MHQ0603P3N5CTD25
3.5 3.5 3.6 3.6 3.7 25 33 50 52 57 MHQ0603P3N5STD25
3.6 3.6 3.7 3.7 3.8 26 33 50 52 57 MHQ0603P3N6BTD25
3.6 3.6 3.7 3.7 3.8 26 33 50 52 57 MHQ0603P3N6CTD25
3.6 3.6 3.7 3.7 3.8 26 33 50 52 57 MHQ0603P3N6STD25
Product No. Manufacturer
4291B+16193A Keysight Technologies
(12/16)
20171113 / inductor_automotive_high-frequency_mhq0603p_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
INDUCTORS
MHQ0603P type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
○Measurement equipment
＊Equivalent measurement equipment may be used.
L(nH)typ. Q typ. Part No.
500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz 500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz
3.7 3.7 3.8 3.8 3.9 26 34 51 52 58 MHQ0603P3N7BTD25
3.7 3.7 3.8 3.8 3.9 26 34 51 52 58 MHQ0603P3N7CTD25
3.7 3.7 3.8 3.8 3.9 26 34 51 52 58 MHQ0603P3N7STD25
3.8 3.8 3.9 3.9 4.0 24 32 49 51 56 MHQ0603P3N8BTD25
3.8 3.8 3.9 3.9 4.0 24 32 49 51 56 MHQ0603P3N8CTD25
3.8 3.8 3.9 3.9 4.0 24 32 49 51 56 MHQ0603P3N8STD25
3.9 3.9 4.0 4.1 4.2 23 30 47 49 54 MHQ0603P3N9BTD25
3.9 3.9 4.0 4.1 4.2 23 30 47 49 54 MHQ0603P3N9CTD25
3.9 3.9 4.0 4.1 4.2 23 30 47 49 54 MHQ0603P3N9STD25
4.0 4.0 4.1 4.2 4.3 26 34 52 53 59 MHQ0603P4N0BTD25
4.0 4.0 4.1 4.2 4.3 26 34 52 53 59 MHQ0603P4N0CTD25
4.0 4.0 4.1 4.2 4.3 26 34 52 53 59 MHQ0603P4N0STD25
4.1 4.1 4.2 4.3 4.4 23 30 46 48 52 MHQ0603P4N1BTD25
4.1 4.1 4.2 4.3 4.4 23 30 46 48 52 MHQ0603P4N1CTD25
4.1 4.1 4.2 4.3 4.4 23 30 46 48 52 MHQ0603P4N1STD25
4.2 4.2 4.3 4.4 4.5 24 31 46 48 52 MHQ0603P4N2BTD25
4.2 4.2 4.3 4.4 4.5 24 31 46 48 52 MHQ0603P4N2CTD25
4.2 4.2 4.3 4.4 4.5 24 31 46 48 52 MHQ0603P4N2STD25
4.3 4.3 4.4 4.5 4.6 25 33 49 51 56 MHQ0603P4N3CTD25
4.3 4.3 4.4 4.5 4.6 25 33 49 51 56 MHQ0603P4N3STD25
4.3 4.3 4.4 4.5 4.6 25 33 49 51 56 MHQ0603P4N3HTD25
4.7 4.7 4.9 4.9 5.1 24 31 47 49 54 MHQ0603P4N7CTD25
4.7 4.7 4.9 4.9 5.1 24 31 47 49 54 MHQ0603P4N7STD25
4.7 4.7 4.9 4.9 5.1 24 31 47 49 54 MHQ0603P4N7HTD25
5.1 5.1 5.3 5.4 5.5 25 32 49 51 56 MHQ0603P5N1CTD25
5.1 5.1 5.3 5.4 5.5 25 32 49 51 56 MHQ0603P5N1STD25
5.1 5.1 5.3 5.4 5.5 25 32 49 51 56 MHQ0603P5N1HTD25
5.6 5.6 5.9 6.0 6.2 24 31 46 48 52 MHQ0603P5N6CTD25
5.6 5.6 5.9 6.0 6.2 24 31 46 48 52 MHQ0603P5N6STD25
5.6 5.6 5.9 6.0 6.2 24 31 46 48 52 MHQ0603P5N6HTD25
6.2 6.2 6.6 6.7 7.0 21 28 42 43 47 MHQ0603P6N2STD25
6.2 6.2 6.6 6.7 7.0 21 28 42 43 47 MHQ0603P6N2HTD25
6.8 6.8 7.2 7.4 7.7 22 28 43 44 48 MHQ0603P6N8HTD25
6.8 6.8 7.2 7.4 7.7 22 28 43 44 48 MHQ0603P6N8JTD25
7.5 7.5 8.1 8.3 8.8 24 30 44 45 48 MHQ0603P7N5HTD25
7.5 7.5 8.1 8.3 8.8 24 30 44 45 48 MHQ0603P7N5JTD25
8.2 8.2 8.9 9.2 9.7 21 27 39 40 42 MHQ0603P8N2HTD25
8.2 8.2 8.9 9.2 9.7 21 27 39 40 42 MHQ0603P8N2JTD25
9.1 9.2 9.9 10.2 10.9 23 29 42 44 46 MHQ0603P9N1HTD25
9.1 9.2 9.9 10.2 10.9 23 29 42 44 46 MHQ0603P9N1JTD25
10.0 10.0 11.0 11.0 12.0 22 28 41 42 43 MHQ0603P10NHTD25
10.0 10.0 11.0 11.0 12.0 22 28 41 42 43 MHQ0603P10NJTD25
11.0 11.0 12.0 13.0 14.0 21 27 37 38 39 MHQ0603P11NHTD25
11.0 11.0 12.0 13.0 14.0 21 27 37 38 39 MHQ0603P11NJTD25
Product No. Manufacturer
4291B+16193A Keysight Technologies
(13/16)
20171113 / inductor_automotive_high-frequency_mhq0603p_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
INDUCTORS
MHQ0603P type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
○Measurement equipment
＊Equivalent measurement equipment may be used.
L(nH)typ. Q typ. Part No.
500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz 500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz
12.0 12.0 14.0 14.0 16.0 23 29 41 41 41 MHQ0603P12NHTD25
12.0 12.0 14.0 14.0 16.0 23 29 41 41 41 MHQ0603P12NJTD25
13.0 13.0 15.0 16.0 18.0 21 27 36 36 36 MHQ0603P13NHTD25
13.0 13.0 15.0 16.0 18.0 21 27 36 36 36 MHQ0603P13NJTD25
15.0 15.0 18.0 19.0 21.0 23 29 37 37 36 MHQ0603P15NHTD25
15.0 15.0 18.0 19.0 21.0 23 29 37 37 36 MHQ0603P15NJTD25
16.0 16.0 19.0 20.0 23.0 22 28 37 37 35 MHQ0603P16NHTD25
16.0 16.0 19.0 20.0 23.0 22 28 37 37 35 MHQ0603P16NJTD25
18.0 18.0 22.0 24.0 28.0 23 28 36 35 33 MHQ0603P18NHTD25
18.0 18.0 22.0 24.0 28.0 23 28 36 35 33 MHQ0603P18NJTD25
20.0 21.0 26.0 28.0 34.0 22 27 33 32 27 MHQ0603P20NHTD25
20.0 21.0 26.0 28.0 34.0 22 27 33 32 27 MHQ0603P20NJTD25
22.0 23.0 29.0 32.0 40.0 23 29 34 33 28 MHQ0603P22NHTD25
22.0 23.0 29.0 32.0 40.0 23 29 34 33 28 MHQ0603P22NJTD25
24.0 25.0 34.0 38.0 — 22 26 29 27 — MHQ0603P24NHTD25
24.0 25.0 34.0 38.0 —22 26 29 27 —MHQ0603P24NJTD25
27.0 28.0 38.0 44.0 — 23 28 30 28 — MHQ0603P27NHTD25
27.0 28.0 38.0 44.0 —23 28 30 28 —MHQ0603P27NJTD25
30.0 32.0 47.0 — — 22 27 — — — MHQ0603P30NHTD25
30.0 32.0 47.0 — — 22 27 ——— MHQ0603P30NJTD25
33.0 35.0 55.0 — — 22 27 — — — MHQ0603P33NHTD25
33.0 35.0 55.0 — — 22 27 ——— MHQ0603P33NJTD25
36.0 38.0 67.0 — — 22 26 — — — MHQ0603P36NHTD25
36.0 38.0 67.0 — — 22 26 ——— MHQ0603P36NJTD25
39.0 42.0 79.0 — — 23 26 — — — MHQ0603P39NHTD25
39.0 42.0 79.0 — — 23 26 ——— MHQ0603P39NJTD25
Product No. Manufacturer
4291B+16193A Keysight Technologies
(14/16)
20171113 / inductor_automotive_high-frequency_mhq0603p_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
INDUCTORS
MHQ0603P type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
○Measurement equipment
＊Equivalent measurement equipment may be used.
Product No. Manufacturer
E4991+16193A Keysight Technologies
1 10 100 1000 10000
0
100
10
1
Frequency (MHz)
Inductance (nH)
1N0
1N2
1N5
1N8
2N2
2N7
3N3
3N9
4N7
5N6
6N8
8N2
10N
12N
15N
18N
22N
27N
39N
33N
(15/16)
20171113 / inductor_automotive_high-frequency_mhq0603p_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
INDUCTORS
MHQ0603P type
ELECTRICAL CHARACTERISTICS
Q FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
○Measurement equipment
＊Equivalent measurement equipment may be used.
Product No. Manufacturer
E4991+16193A Keysight Technologies
1 10 100 1000 10000
Frequency (MHz)
0
10
20
30
40
50
60
70
80
90
100
Q
1N0 1N2
1N5
1N8
2N2
2N7
3N3
3N9
4N7
5N6
6N8
8N2
10N
12N
15N
18N
22N
27N
33N
39N
(16/16)
20171113 / inductor_automotive_high-frequency_mhq0603p_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
INDUCTORS
MHQ0603P type
PACKAGING STYLE
REEL DIMENSIONS
TAPE DIMENSIONS
1.0
ø180±2.0
2.0±0.5
ø13±0.2
ø21±0.8
ø60min.
14.4max.
Dimensions in mm
8.4 +2.0
–0.0
8.0±0.3 3.5±0.05
1.75±0.1
4.0±0.1
1.5 +0.1
–0.0
Sprocket hole Cavity
A
KB
2.0±0.05 2.0±0.05
160min. Taping 200min.
300min.
Drawing direction
Typ e A B K
MHQ0603P 0.74±0.05 0.44±0.05 0.60 max.