Monolithic Hall Effect ICs EM-1781 Shipped in packet-tape reel(5000pcs/Reel) EM-1781 is ultra-small Hall effect ICs of a single silicon chip composed of Hall element and a signal processing IC. Omnipolar Hall Supply Voltage Effect Switch 1.65.5 Hall Element Pulse Excitation High Sensitivity Output Bop3mT CMOS SMT Operational Characteristics Vout S or N VOH H Marking 1VDD 1 2 2OUT BhN N or S BhS 3N.C. VOL 4VSS BopN BrpN 0 N-pole L BrpS BopS S-pole Functional Block Diagram Magnetic flux density 1:VDD Switch Item Symbol Limit Unit Supply Voltage VDD -0.1 6.0 V Output Current Iout 0.5 mA Operating Temperature Range Topr -30 85 Storage Temperature Range Tstg -40 125 Dynamic Offset Cancellator Absolute Maximum RatingsTa=25 2:OUT 4:Vss Pulse Hall Chopper Amplifier Regulator Element Stabilizer Schmitt trigger &Latch Output Stage Magnetic q and Electrical CharacteristicsTa=25 VDD=1.85V Magnetic Characteristics wTa=-3085 VDD=1.85V Item Supply Voltage Symbol Conditions VDD Min. Typ. Max. Unit 1.6 BOPS Operating Point IBOPNI 1.4* BrpS Release Point IBrpNI BhS Hysteresis I B h NI P e r i o d Tp Output High Voltage VOH Output Low Voltage VOL Io=0.5mA Supply Current IDD Average Io=-0.5mA 5.5 3.0 4.0 Item Symbol Conditions 1.2 3.0 4.4 mT mT Release 0.9 2.2 4.1 mT B S H y s t e r e s i s BhN I h I 0.1 0.8 1.7 mT 2.2 3.7* mT 0.3* 0.8 1.5* mT 50 100 ms Note) The above specifications are design targets. Application Circuit V VDD CMOS 0.4 V 9 A OUT The characteristics with*marks are design targets. 6.5 1mT=10Gauss VDD EM-1781 N.C. Bypass Capacitor 0.1F VSS GND 43 Typ. Max. Unit BrpS Point IB NI rp V 1.1 VDD-0.4 Min. B S Operating Point IBOPNI OP EM-1781 *Please be aware that our products are not intended for use in life support equipment, devices, or systems. Use of our products in such applications requires the advance written approval of our sales staff. Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks, adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of our products in such applications is understood to be fully at the risk of the customer using our devices or systems. b (For reference only)Land PatternUnit:mm) PackageUnit:mm) 0.50 1 0.3 Sensor center 00.1 0.90 2.10.2 1.250.1 2 0.25 2.10.1 1.3 0.3 Line marking 5 1.90 5 3 4 0.1 0.55-0 0.3 0.25 0.1 5 5 Pin No. 1 2 3 4 Pin Name Function Comment VDD Supply Voltage OUT Output Voltage N.C. - Short to GND VSS GND Note1) The sensor center is located within the 0.3mm circle. Note2) The tolerances of dimensions with no mentions is 0.1mm. Note3) Coplanarity:The differnces between standoff of terminals are max.0.1mm. Note4) The sensor part is located 0.4mm(typ.) far from marking surface. Supply Voltage 1.30 IDD Pulse DrivingVDD=1.85V 6 50ms IDD 146s 5 Supply VoltageV f IDD ON TYP : 1.8mA 4 j 3 2 IDD TYP : 6.5A 1 IDD OFF TYP : 1.3A time 0 -40 -20 0 20 40 60 80 100 Ambient Temperature Temparature Dependence of Bop. Brp Function Timing Chart IDD Operating PointmT 6 4 BopS n 2 0 t B BrpS Bop VDD1.85V t B o Brp BrpN -2 Vout High BopN -4 -6 -50 IDD 0 50 Ambient Temperature 100 t 48.8s Vout High t 48.8s Low Low t t Operating Point Timing Release Point Timing This Hall IC s o utpu t is h eld as interna l da ta just be fo re the interna l circ uit t u r n s O F F ( I D D O F F ) . A n d a f t e r 4 8 . 8 s , t h e o u t p u t c h a n g e s . N o t e ) 4 8 . 8 s i n f i g u r e s i s t y p i c a l v a l u e 44 p IMPORTANT NOTICE These products and their specifications are subject to change without notice. When you consider any use or application of these products, please make inquiries the sales office of Asahi Kasei Microdevices Corporation (AKM) or authorized distributors as to current status of the products. Descriptions of external circuits, application circuits, software and other related information contained in this document are provided only to illustrate the operation and application examples of the semiconductor products. You are fully responsible for the incorporation of these external circuits, application circuits, software and other related information in the design of your equipments. AKM assumes no responsibility for any losses incurred by you or third parties arising from the use of these information herein. AKM assumes no liability for infringement of any patent, intellectual property, or other rights in the application or use of such information contained herein. Any export of these products, or devices or systems containing them, may require an export license or other official approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange, or strategic materials. AKM products are neither intended nor authorized for use as critical componentsNote1) in any safety, life support, or other hazard related device or systemNote2), and AKM assumes no responsibility for such use, except for the use approved with the express written consent by Representative Director of AKM. As used here: Note1) A critical component is one whose failure to function or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability. Note2) A hazard related device or system is one designed or intended for life support or maintenance of safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property. It is the responsibility of the buyer or distributor of AKM products, who distributes, disposes of, or otherwise places the product with a third party, to notify such third party in advance of the above content and conditions, and the buyer or distributor agrees to assume any and all responsibility and liability for and hold AKM harmless from any and all claims arising from the use of said product in the absence of such notification. April 4, 2012