Previous Vectron Model Number C3310
Output Frequency Range 10 MHz – 160 MHz
Standard Frequencies 10; 25; 26; 39.3216; 52; 56; 61.44;77.76; 104 MHz
122.88; 153.6; 155.52; 160 MHz
Parameter Min Typ Max Units Condition
Input frequency 2 100 MHz ± 2 ppm
Signal HCMOS
HCMOS / similar sinewave
Reference Level
Reference Input Impedance
0.5
2
4 Vpp
kΩ
Parameter Min Typ Max Units Condition
Output frequency 10 160 MHz
Signal HCMOS
@ 15 pF 10 to 90 %
@ Vs/2
Load 15.0 pF
Rise and Fall time 5 ns
Duty cycle 40 60 %
FX-501
Frequency Controlled Crystal Oscillator
Reference Frequency
Base Stations
Test Equipment
Messurement
Surface Mount Package
Reow Process Compatible
Low Phase Noise
Build in PPL-Circuit
Features Typical Applications
Output Frequency
htttp://www.vectron.com
Vectron International•267 LowellRoad, Hudson, New Hampshire 03051•Tel:+1-88-VECTRON-1
Vectron International GmbH & Co. KG • Landstraße, 74924 Neckarbischofsheim, Germany • Tel: +49 7268 801 100
FX-501 page: 1/5
Parameter Min Typ Max Units Condition
Supply voltage [Standard] 3.135 3.3 3.465 VDC
Current consumption 50 mA steady state @ +25°C & 3.3VDC
Parameter Min Typ Max Units Condition
Phase Noise3-90 dBc/Hz 10 Hz @ 122,88 MHz
-110 dBc/Hz 100 Hz HCMOS
-131 dBc/Hz 1 kHz
-148 dBc/Hz 10 kHz
-156 dBc/Hz 100 kHz
-157 dBc/Hz 1 MHz
Jitter 0.77 ps RMS @ 10Hz .. 150kHz
Weight 9 g
Processing & Packing Handling & processing note
Operating temperature range -20 +70 °C
Operable temperature range -30 +85 °C
Storage temperature range -55 +125 °C
10 MHz; HCMOS output 122,88MHz; HCMOS output
Frequency range [Hz] Jitter [ps rms] Frequency range [Hz] Jitter [ps rms]
10Hz to 100kHz 0.708ps 10Hz to 150kHz 0.755ps
Supply Voltage (Vs)
Additional Parameters
htttp://www.vectron.com
Vectron International•267 LowellRoad, Hudson, New Hampshire 03051•Tel:+1-88-VECTRON-1
Vectron International GmbH & Co. KG • Landstraße, 74924 Neckarbischofsheim, Germany • Tel: +49 7268 801 100
FX-501 page: 2/5
Typical Phase Noise and Jitter
Type G218B
Input : Single ended (HCMOS or Sinewave)
Output : Single ended HCMOS
Height “H” Pin Length “L”
5.9 NA
Dimensions : mm
Pin Connections Description
1 Ref. Frequency in High stable input frequency for syncronisation
2 VCXO Control Test output of the control voltage for the VCXO
Only for modul test or observance
3GND Ground connection. Keep traces physically short and connect immediately to ground plane for best performance
4RF-OUT RF syncronised output.
5 Lock Detector Output
Test output signal for PLL lock detected.
High signal PLL in lock
Low signal PLL out of lock
Only for modul test or observance
6 Vs Power Supply Pin
Marking
FX-501
Frequency
● AYYWW
Absolute Maximum Ratings
htttp://www.vectron.com
Vectron International•267 LowellRoad, Hudson, New Hampshire 03051•Tel:+1-88-VECTRON-1
Vectron International GmbH & Co. KG • Landstraße, 74924 Neckarbischofsheim, Germany • Tel: +49 7268 801 100
Enclosure
FX-501 page: 3/5
Parameter Min Typ Max Units Condition
Supply voltage (Vs) 6.0 V
Maximum output load @ CMOS 40 pF
Standard Shipping Methode
htttp://www.vectron.com
Vectron International•267 LowellRoad, Hudson, New Hampshire 03051•Tel:+1-88-VECTRON-1
Vectron International GmbH & Co. KG • Landstraße, 74924 Neckarbischofsheim, Germany • Tel: +49 7268 801 100
Block Diagram
FX-501 page: 4/5
VS
8
15
4
0
8
1 5
4
VCXO
PLL
Circuit
Reference
Frequency VCXO
Lock
Detector
VCXO
Control
0
VCXO
VS
VS
0
Loop
Filter
VS
*bei W ≤ 24 mm nur untere Lochreihe
∗by W≤ 24 mm only lower hole line
Gurtoberseite
Tape upper side
Gurtunterseite
Tape buttom side
Abwickelrichtung
Unwinding direction
Lage im Gurt
Position in tape
Pin 1
A
X
P
B
K
Production tolerance complying DIN IEC 286-3
Enclosure Type Tape width W [mm] Quantity per meter Quantity per reel Dimension P
G218B tbd tbd 850 tbd
Notes:
1Contact factory for improved stabilities or additional product options. Not all options and codes are available at all
frequencies.
2Unless otherwise stated all values are valid after warm-up time and refer to typical conditions for supply voltage,
frequency control voltage, load, temperature (25°C)
3 Phase noise degrades with increasing output frequency.
4Subject to technical modication.
5 Contact factory for availability.
Prole Feature Pb-Free Assembly/
Sn-Pb Assembly Prole Feature Pb-Free Assembly/
Sn-Pb Assembly
Average ramp-up rate (TL to Tp)3°C/second max. Time 25°C to Peak Temperature 8 minutes max.
Preheat -Temperature Min TSmin
-Temperature Min Tsmax
-Time (min to max) tS
150°C
200°C
60-180 seconds
Time maintainted above
-Temperature (TL)
-Time (tL)
217°C
60-150 seconds
TSmax to TL-Ramp-up Rate 3°C/second max
Time maintainted above
-Temperature (TL)
-Time (tL)
217°C
60-150 seconds
Time within 5°C of actual Peak
Temperature (tP)20-40 seconds
Peak Temperature (TP)max 260°C Ramp-down Rate 6°C/ second max
Note: All temperatures refer to topside of the package, measured on the package body surface.
SMD oscillators must be on the top side of the PCB during the reow process
How to order this product:
Supply Voltage Code:
E: 3,3 V
RF Output Code:
A: HCMOS
Height:
1: 5,9 mm
Temperature Range:
F: -40...+85°C
J: -20...+70°C
htttp://www.vectron.com
Vectron International•267 LowellRoad, Hudson, New Hampshire 03051•Tel:+1-88-VECTRON-1
Vectron International GmbH & Co. KG • Landstraße, 74924 Neckarbischofsheim, Germany • Tel: +49 7268 801 100
Recommanded Reow Prole
Use this worksheet to forward the following information to your factory representative:
Model Height - Supply Voltage
Code
RF Output
Code
Temperature
Range -
Reference
Frequency -Output Frequency
FX-501 1 - EA J - -
FX-501 page: 5/5