AWT6252 IMT/WCDMA 3.4V/27.5dBm Linear Power Amplifier Module PRELIMINARY DATA SHEET - Rev 1.6 FEATURES * InGaP HBT Technology * High Efficiency: 41% - Low Bias Mode 39% - High Bias Mode * Low Quiescent Current: 50 mA * Low Leakage Current in Shutdown Mode: <1 A * VREF = +2.85 V (+2.75 V min over temp) * Optimized for a 50 System * Low Profile Miniature Surface Mount Package: 1.56mm Max * RoHS Compliant Package Option, 250 oC MSL-3 AWT6252 M7 Package 10 Pin 4 mm x 4 mm x 1.5 mm Surface Mount Module APPLICATIONS * Dual Mode 3GPP Wireless Handsets PRODUCT DESCRIPTION The AWT6252 meets the increasing demands for higher output power in 3GPP 1XRTT handsets. The PA module is optimized for VREF = +2.85 V, a requirement for compatibility with the Qualcomm(R) 6250 chipset. The device is manufactured on an advanced InGaP HBT MMIC technology offering state-of-the-art reliability, temperature stability, and ruggedness. Selectable bias modes that optimize efficiency for different output power levels, and a shutdown mode with low leakage current, increase handset talk and standby time. The self-contained 4 mm x 4 mm x 1.5 mm surface mount package incorporates matching networks optimized for output power, efficiency, and linearity in a 50 system. GND at slug (pad) VCC 1 10 VCC RFIN 2 9 GND GND 3 8 RFOUT 7 GND 6 GND VMODE 4 Bias Control VREF 5 Figure 1: Block Diagram 06/2005 AWT6252 GND VCC 1 10 VCC RFIN 2 9 GND GND 3 8 RFOUT VMODE 4 7 GND VREF 5 6 GND GND Figure 2: Pinout (X-ray Top View) Table 1: Pin Description 2 PIN NAME DESCRIPTION 1 V CC Supply Voltage 2 RFIN RF Input 3 GND Ground 4 VMODE Mode Control Voltage 5 VREF Reference Voltage 6 GND Ground 7 GND Ground 8 RFOUT RF Output 9 GND Ground 10 V CC Supply Voltage PRELIMINARY DATA SHEET - Rev 1.6 06/2005 AWT6252 ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PARAMETER MIN MAX UNIT Supply Voltage (VCC) 0 +5 V Mode Control Voltage (VMODE) 0 +3.5 V Reference Voltage (VREF) 0 +3.5 V RF Input Power (PIN) - +10 dB m -40 +150 C Storage Temperature (TSTG) Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Table 3: Operating Ranges PARAMETER MIN TYP MAX UNIT Operating Frequency (f) 1920 - 1980 MHz Supply Voltage (VCC) +3.2 +3.4 +4.2 V Reference Voltage (VREF) +2.75 0 +2.85 - +2.95 +0.5 V PA "on" PA "shut down" Mode Control Voltage (VMODE) +2.5 0 +2.8 - +3.1 +0.5 V Low Bias Mode High Bias Mode +27.5 - dB m - +90 C RF Output Power (POUT) +27.0 Case Temperature (TC) -10 (1) COMMENTS The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Notes: (1) For operation at TC = +90 oC and VCC = +3.2 V, POUT is derated by 0.5 dB. PRELIMINARY DATA SHEET - Rev 1.6 06/2005 3 AWT6252 Table 4: Electrical Specifications (TC = +25 C, VCC = +3.4 V, VREF = +2.85 V, 50 system) PARAMETER MIN TYP MAX Gain 24.5 22 17 26.5 24.5 20.5 29 27 24 dB - -43 -41 -46 -38 -38 -38 dB c - -60 -62 -60 -50 -50 -48 dB c 37 8.5 19 39 9.5 21.5 - % Quiescent Current (Icq) - 53 65 mA VMODE = +2.85 V Reference Current - 3.8 5 mA through VREF pin Mode Control Current - 0.3 0.5 mA through VMODE pin, VMODE = +2.85 V Leakage Current - <1 5 A VCC = +4.2 V, VREF = 0 V, VMODE = 0 V Noise in Receive Band - -139 -137 Harmonics 2fo 3fo, 4fo - -45 -50 -30 -30 dB c Input Impedance - - 2:1 VSWR ACLR1 at 5 MHz offset (1) ACLR2 at 10 MHz offset Power-Added Efficiency (1) Spurious Output Level (all spurious outputs) Load mismatch stress with no permanent degradation or failure UNIT POUT = +27.5 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.85 V POUT = +16 dBm, VCC = 1.5 V, VMODE = +2.85 V POUT = +27.5 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.85 V POUT = +16 dBm, VCC = 1.5 V, VMODE = +2.85 V POUT = +27.5 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.85 V POUT = +16 dBm, VCC = 1.5 V, VMODE = +2.85 V POUT = +27.5 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.85 V POUT = +16 dBm, VCC = 1.5 V, VMODE = +2.85 V dBm/Hz 2110 MHz to 2170 MHz - - -70 dB c 8:1 - - VSWR Notes: (1) ACLR and Efficiency measured at 1950 MHz. 4 COMMENTS PRELIMINARY DATA SHEET - Rev 1.6 06/2005 POUT < +27.5 dBm In-band load VSWR < 5:1 Out-of-band load VSWR < 10:1 Applies over all voltage and temperature operating ranges VCC = +5.0 V, PIN = +5 dBm Applies over full operating temperature range AWT6252 Table 5: Electrical Specifications (TC = +25 C, VCC = +3.4 V, VREF = +2.85 V, VMODE = +2.85 V, 50 system) PARAMETER MIN TYP MAX UNIT 24 22 17 26 24.5 20.5 28 27 24 dB POUT = +27.5 dBm POUT = +16 dBm POUT = +16 dBm, VCC = 1.5 V ACLR1 at 5 MHz offset (1) - -41 -41 -46 -37 -38 -38 dB c POUT = +27.5 dBm, POUT = +16 dBm, POUT = +16 dBm, VCC = 1.5 V, ACLR2 at 10 MHz offset - -56 -62 -60 -50 -50 -48 dB c POUT = +27.5 dBm POUT = +16 dBm, POUT = +16 dBm, VCC = 1.5 V 38 8.5 19 41 9.5 21.5 - % POUT = +27.5 dBm POUT = +16 dBm POUT = +16 dBm, VCC = 1.5 V, Quiescent Current (Icq) - 53 65 mA Reference Current - 3.8 5 mA through VREF pin Mode Control Current - 0.3 0.5 mA through VMODE pin Leakage Current - <1 5 A VCC = +4.2 V, VREF = 0 V, VMODE = 0 V Noise in Receive Band - -138 -136 Harmonics 2fo 3fo, 4fo - -45 -50 -30 -30 dB c Input Impedance - - 2:1 VSWR Gain Power-Added Efficiency (1) Spurious Output Level (all spurious outputs) Load mismatch stress with no permanent degradation or failure COMMENTS dBm/Hz 2110 MHz to 2170 MHz - - -70 dB c 8:1 - - VSWR POUT < +27.5 dBm In-band load VSWR < 5:1 Out-of-band load VSWR < 10:1 Applies over all voltage and temperature operating ranges VCC = +5.0 V, PIN = +5 dBm Applies over full operating temperature range Notes: (1) ACLR and Efficiency measured at 1950 MHz. PRELIMINARY DATA SHEET - Rev 1.6 06/2005 5 AWT6252 APPLICATION INFORMATION To ensure proper performance, refer to all related Application Notes on the ANADIGICS web site: http://www.anadigics.com Shutdown Mode The power amplifier may be placed in a shutdown mode by applying logic low levels (see Operating Ranges table) to both the VREF and VMODE voltages. Bias Modes The power amplifier may be placed in either a Low Bias mode or a High Bias mode by applying the appropriate logic level (see Operating Ranges table) to the VMODE voltage. The Bias Control table lists the recommended modes of operation for various applications. Table 6: Bias Control APPLICATION POUT LE V E LS BIAS MODE CDMA - low power <+16dBm Low +2.85 V +2.85 V CDMA - high power >+16 dBm High +2.85 V 0V +3.4 - Shutdown 0V 0V - Shutdown C1 0.01 F VCC1 C10 2.2 F RFIN VMODE VREF C11 1.0 F GND at slug VCC1 RFIN GND AWT6252 VMODE VREF C2 0.01 F V R EF V CC > +1.5 C4 0.01 F VCC2 GND RFOUT C6 1.0 F GND GND GND at slug Figure 3: Application Circuit Schematic 6 VMODE PRELIMINARY DATA SHEET - Rev 1.6 06/2005 C7 2.2 F VCC2 RFOUT AWT6252 PACKAGE OUTLINE Figure 4: M7 Package Outline - 10 Pin 4 mm x 4 mm x 1.5 mm Surface Mount Module 5 5 Figure 5: Branding Specification PRELIMINARY DATA SHEET - Rev 1.6 06/2005 7 AWT6252 AWT6252R 52R Figure 6: Branding Specification - RoHS Compliant Package 8 PRELIMINARY DATA SHEET - Rev 1.6 06/2005 AWT6252 COMPONENT PACKAGING Figure 7: Tape & Reel Packaging Table 7: Tape & Reel Dimensions PACKAGE TYPE TAPE WIDTH POCKET PITCH R EEL CAPACITY MAX REEL DIA 4 mm x 4 mm x 1.5 mm 12 mm 8 mm 2500 13" PRELIMINARY DATA SHEET - Rev 1.6 06/2005 9 AWT6252 NOTES 10 PRELIMINARY DATA SHEET - Rev 1.6 06/2005 AWT6252 NOTES PRELIMINARY DATA SHEET - Rev 1.6 06/2005 11 AWT6252 NOTES 12 PRELIMINARY DATA SHEET - Rev 1.6 06/2005 AWT6252 ORDERING INFORMATION ORDER NUMBER TEMPERATURE RANGE PACKAGE DESCRIPTION AWT6252M7P8 -10 oC to +90 oC 10 P i n 4 mm x 4 mm x 1.5 mm Surface Mount Module AWT6252RM7P8 -10 oC to +90 oC RoHS Compliant 10 Pin 4 mm x 4 mm x 1.5 mm Tape and Reel, 2500 pieces per Reel Surface Mount Module COMPONENT PACKAGING Tape and Reel, 2500 pieces per Reel ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: Mktg@anadigics.com IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product's formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. WARNING ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 13 PRELIMINARY DATA SHEET - Rev 1.6 06/2005