RP108J Series Low Input Voltage 3A LDO Regulator NO.EA-203-150817 OUTLINE The RP108J is a CMOS-based voltage regulator IC featuring 3A output with low ON-resistance. The RP108J consists of a voltage reference unit, an error amplifier, resistor-net for voltage setting, a fold-back protection circuit, and a thermal shutdown circuit. The RP108J features both low supply current and high output current, and the dropout voltage is much smaller than bi-polar's. The minimum input voltage is as low as 1.6V and the output voltage can be set from 0.8V, therefore it can be connected with the DC/DC converter as the latter power supply for high density LSI that is operated by low output voltage. The output voltage of RP108J081x is externally adjustable by using external divide resistors. The CE pin of the RP108J can switch the regulator to standby mode. In addition to a fold-back protection circuit, which is already built in the conventional regulators, The RP108J contains a thermal shutdown circuit, a constant slope circuit as a soft-start function and a reverse current protection circuit. Ceramic capacitors can be used. FEATURES * * * * * * * * * * * * * * * * Output Current ............................................................. Min. 3A Supply Current ............................................................. Typ. 350A Standby Current ........................................................... Typ. 2A Input Voltage Range .................................................... 1.6V to 5.25V Output Voltage Range.................................................. Fixed Output Voltage Type: 0.8V to 4.2V (0.1V steps) * Refer to MARK INFORMATIONS for other voltages. Adjustable Output Voltage Type: 0.8V to 4.2V Output Voltage Accuracy.............................................. 1.0% (15mV accuracy, When VSET 1.5V) Output Voltage Temperature-drift Coefficient ........... Typ. 100ppm/C Ripple Rejection ........................................................... Typ. 65dB (f = 1kHz, VSET = 2.8V) Dropout Voltage ........................................................... Typ. 0.51V (VSET=2.8V) Line Regulation ............................................................ Typ. 0.1%/V Package ....................................................................... TO-252-5-P2 Built-in Fold-back Protection Circuit ............................. Typ. 220mA Built-in Thermal Shutdown Circuit................................ Stops at 165C Built-in Constant Slope Circuit Built-in Reverse Current Protection Circuit Ceramic capacitors are recommended to be used with this IC **** 10F or more APPLICATIONS * Power source for battery-powered equipments. * Power source for portable communication equipments such as cameras and VCRs. * Power source for electrical home appliances. 1 RP108J NO.EA-203-150817 BLOCK DIAGRAMS RP108Jxx1B/E VDD RP108Jxx1D/F VOUT VDD VOUT VFB VFB Vref Vref Current Limit Thermal Shutdown Current Limit Thermal Shutdown CE GND Reverse Detecter CE GND Reverse Detecter SELECTION GUIDE The output voltage, auto discharge function, and the soft-start time for the ICs can be selected at the user's request. Product Name RP108Jxx1(y) -T1-FE Package Quantity per Reel Pb Free Halogen Free TO-252-5-P2 3,000 pcs Yes Yes xx: The set output voltage (VSET) can be designated in the range of 0.8V(08) to 4.2V(42) in 0.1V steps. y: If the output voltage includes the 3rd digit, indicate the digit of 0.01V. (1.25V, 1.85V, 2.85V) Ex. If the output voltage is 1.25V, RP108J1215-T1-FE. If the output voltage is 1.85V, RP108J1815-T1-FE. If the output voltage is 2.85V, RP108J2815-T1-FE. : Designation of auto-discharge function at off state and the soft-start time (B) No auto-discharge function, soft start time typ. 180 s (D) Auto-discharge function, soft start time typ. 180 s (E) No auto-discharge function, soft start time typ. 570 s (F) Auto-discharge function, soft start time typ. 570 s . Auto-discharge function quickly lowers the output voltage to 0V, when the chip enable signal is switched from the active mode to the standby mode, by releasing the electrical charge accumulated in the external capacitor. Refer to CONSTANT SLOPE CIRCUIT for detailed information on the difference of soft-start time and its effect. 2 RP108J NO.EA-203-150817 PIN DESCRIPTIONS TO-252-5-P2 1 2 3 4 5 TO-252-5-P2 Pin No. Symbol Description 1 CE Chip Enable Pin ("H" Active) 2 VDD Input Pin 3 GND Ground Pin 4 VOUT Output Pin 5 VFB Feedback Pin *1 The tab on the bottom of the package enhances thermal performance and is electrically connected to GND (substrate level). It is recommended that the tab be connected to the ground plane on the board, or otherwise be left floating. The VOUT pin should be connected to the VFB pin when using RP108J as an internal fixed output voltage type. In case of using RP108J as an external adjustable type, please refer to "Adjustable Output Voltage Type Settings". 3 RP108J NO.EA-203-150817 ABSOLUTE MAXIMUM RATINGS Symbol Item Rating Unit 6.0 V VIN Input Voltage VCE Input Voltage (CE Input Pin) -0.3 to 6.0 V VFB Input Voltage (VFB Pin) -0.3 to 6.0 V VOUT Output Voltage -0.3 to VIN+0.3 V High Wattage Land Pattern 3800 Standard Land Pattern 1900 PD Power Dissipation (TO-252-5P2)*1 Ta Operating Temperature -40 to 85 C Storage Temperature -55 to 125 C Tstg mV *1 For Power Dissipation, please refer to PACKAGE INFORMATION. ABSOLUTE MAXIMUM RATINGS Electronic and mechanical stress momentarily exceeded absolute maximum ratings may cause the permanent damages and may degrade the life time and safety for both device and system using the device in the field. The functional operation at or over these absolute maximum ratings are not assured. 4 RP108J NO.EA-203-150817 ELECTRICAL CHARACTERISTICS VIN = VSET +1.0V, IOUT =1mA, CIN = COUT = 10F, unless otherwise noted. are guaranteed by design engineering at - 40C Ta 85C. The specifications surrounded by RP108Jxx1B/D/E/F Symbol (Ta=25C) Item Conditions Ta = 25C VOUT Output Voltage -40C Ta 85C ILIM Min. Typ. Max. Unit VSET > 1.5V x0.99 x1.01 V VSET 1.5V -15 15 mV VSET > 1.5V x0.97 x1.02 V VSET 1.5V -45 30 mV Output Current Limit A 3.0 1mA IOUT 300mA -15 2.0 20 1mA IOUT 3000mA -70 3.0 50 VOUT/ IOUT Load regulation VDIF Dropout Voltage ISS Supply Current IOUT = 0mA 350 500 A Istandby Standby Current VCE = 0V 2.0 5.0 A VOUT /VIN Line Regulation VSET +0.5V VIN 5.25V, IOUT=1mA (When VSET 1.1V, VIN = 1.6V) 0.10 0.15 %/V VIN Input Voltage1 5.25 V RR Ripple Rejection mV Please refer to Dropout Voltage on the next page. 1.6 f = 1kHz, Ripple 0.2Vp-p IOUT =100mA VSET 2.8V 65 dB VSET > 2.8V 55 dB Output Voltage -40C Ta 85C Temperature Coefficient 100 ppm /C ISC Short Current Limit 220 mA IPD CE Pull-down Current VCEH CE Input Voltage "H" VCEL CE Input Voltage "L" VOUT /Ta en TTSD TTSR RLOW IREV Output Noise Thermal Shutdown Temperature Thermal Shutdown Released Temperature Auto-discharge Nch Tr. ON Resistance (D/F version) Reverse Current Limit VOUT = 0V 0.3 0.6 A V 1.0 0.4 V BW = 10Hz to 100kHz 70 Vrms Junction Temperature 165 C Junction Temperature 95 C VIN = 4.0V, VCE = 0V 30 VOUT > 0.5V, 0V VIN 5.25V 10 A All test items listed under Electrical Characteristics are done under the pulse load condition (Tj Ta = 25C) except Ripple Rejection, Output Voltage Temperature Coefficient, Output Noise and Thermal Shutdown. 1 The maximum input voltage listed under Electrical Characteristics is 5.25V. If for any reason the input voltage exceeds 5.25V, it has to be no more than 5.5V with 500 cumulative operating hours. 5 RP108J NO.EA-203-150817 The specifications surrounded by are guaranteed by design engineering at - 40C Ta 85C. Dropout Voltage by Output Voltage Output Voltage VSET (V) (Ta=25C) Dropout Voltage VDIF (V) Typ. Max. 0.8 VSET < 0.9 0.910 1.110 0.9 VSET < 1.0 0.865 1.000 1.0 VSET < 1.1 0.810 0.950 0.755 0.895 0.720 0.840 1.5 VSET < 2.5 0.630 0.760 2.5 VSET < 3.3 0.510 0.600 3.3 VSET 4.2 0.480 0.560 1.1 VSET < 1.2 1.2 VSET < 1.5 Condition IOUT=3000mA RECOMMENDED OPERATING CONDITIONS (ELECTRICAL CHARACTERISTICS) All of electronic equipment should be designed that the mounted semiconductor devices operate within the recommended operating conditions. The semiconductor devices cannot operate normally over the recommended operating conditions, even if when they are used over such conditions by momentary electronic noise or surge. And the semiconductor devices may receive serious damage when they continue to operate over the recommended operating conditions. 6 RP108J NO.EA-203-150817 TYPICAL APPLICATIONS VDD VOUT VOUT RP108Jxx1x C1 C2 VFB CE GND Typical Application VDD RP108J081x C1 VOUT VOUT R1 C2 VFB R2 CE GND Typical application for adjustable output voltage type External Components Symbol Descriptions C1, C2 10F (Ceramic), CM21X7R106M06AB, KYOCERA 7 RP108J NO.EA-203-150817 TECHNICAL NOTES When using the RP108J as an internally fixed output voltage type, please connect the VOUT pin to the VFB pin. However, when using it as the Adjustable Output Voltage Type, The output voltage of the externally adjustable output voltage type should be set to 4.2V or less. Also, total resistors value of R1 and R2 should be 20k or less. Phase Compensation In the IC, phase compensation is made for securing stable operation even if the load current is varied. For this purpose, use a 10F or more capacitor C2. In case of using a tantalum capacitor and its ESR is large, the output may be unstable. Therefore, select C2 carefully considering its frequency characteristics. The recommended temperature characteristics for C1 and C2 capacitors are the followings. B Characteristics: Temperature range from -25C to 85C, Capacitance change of 10% X5R Characteristics: Temperature range from -55C to 85C, Capacitance change of 15% X7R Characteristics: Temperature range from -55C to 125C, Capacitance change of 15% The recommended capacitor's tolerable voltage is twice as large as the voltage of use (C1: Input voltage, C2: Output voltage). The upper limit of the capacitance value for C2 is 100F. However, the increase of C2 leads to the increase of inrush current. Refer to CONSTANT SLOPE CIRCUIT for detailed information. PCB Layout Make VDD and GND lines sufficient. If their impedance is high, noise pickup or unstable operation may result. Connect a capacitor C1 with a capacitance value as much as 10F or more between VDD and GND pin, and as close as possible to the pins. Set external components, especially the output capacitor C2, as close as possible to the ICs and make wiring as short as possible. Transient Response When using the Adjustable Output Voltage Type, the transient response could be affected by the external resistors. Evaluate the circuit taking the actual conditions of use into account. 8 RP108J NO.EA-203-150817 ADUSTABLE OUTPUT VOLTAGE TYPE SETTINGS * Output Voltage Setting Method RP108J081x can be adjusted the output voltage by using the external divider resistors. If the VFB voltage fixed into the IC is described as SetVFB, the output voltage can be set by using the following equations SetVFB is equal to 0.8V. The VOUT pin of RP108J081x should be connected to the VFB pin. VOUT R1 I1 VFB RIC GND Thus, VOUT IIC R2 I2 SetVFB I1= IIC + I2 .................................................................................................................................. (1) I2= SetVFB / R2......................................................................................................................... (2) I1= IIC + SetVFB /R2.................................................................................................................... (3) Therefore, VOUT= SetVFB x R1 x I1 ............................................................................................................ (4) Put Equation (3) into Equation (4), then VOUT ........................................................................................................................................................= SetVFB + R1(IIC + SetVFB / R2) = SetVFB x (1+R1/ R2) + R1 x IIC....................................................................................... (5) In Equation (5), R1x IIC is the error-causing factor in VOUT. As for IIC, IIC= SetVFB / RIC ........................................................................................................................ (6) Therefore, the error-causing factor R1x IIC can be described as follows. R1xIIC .................................................................................................................................................................................... = R1 x SetVFB / RIC = SetVFB x R1 / RIC ......................................................................................................... (7) For better accuracy, choosing R1 (<<RIC) reduces this error. Without the error-causing factor R1x IIC, the output voltage can be calculated by the following equation VOUT = SetVFB x ((R1 + R2) / R2) ............................................................................................. (8) RIC of RP108J is approximately Typ.1.6M (Ta=25C, this value is guaranteed by design.). The value could be affected by the temperature, therefore evaluate the circuit taking the actual conditions of use into account. 9 RP108J NO.EA-203-150817 REVERSE CURRENT PROTECTION CIRCUIT The RP108J includes a Reverse Current Protection Circuit, which stops the reverse current from VOUT pin to VDD pin or to GND pin when VOUT becomes higher than VIN. Usually, the LDO using Pch output transistor contains a parasitic diode between VDD pin and VOUT pin. Therefore, if VOUT is higher than VIN, the parasitic diode becomes forward direction. As a result, the current flows from VOUT pin to VDD pin. The RP108J switches the mode to the reverse current protection mode before VIN becomes lower than VOUT by connecting the parasitic diode of Pch output transistor to the backward direction, and connecting the gate to VOUT pin. As a result, the Pch output transistor is turned off and the all the current pathways from VOUT pin to GND pin are shut down to maintain the reverse current lower than 10A. Switching to either the normal mode or to the reverse current protection mode is determined by the magnitude of VIN voltage and VOUT voltage. For the stable operation, offset and hysteresis are set as the threshold. Offset is set to 30mV (Typ.25C) and hysteresis is set to 5mV (Typ.25C). Therefore, the minimum dropout voltage under the small load current condition is restricted by the value of 35mV (Typ.25C). Fig.1 and Fig.2 show the diagrams of each mode, and Fig.3 shows the load characteristics of each mode. When giving the VOUT pin a constant-voltage and decreasing the VIN voltage, the dropout voltage will become lower than 30mV (Typ.25C). As a result, the reverse current protection starts to function to stop the load current. By increasing the dropout voltage higher than 35mV (Typ.25C), the protection mode will be released to let the load current to flow. If the dropout voltage to be used is lower than 30mV (Typ.25C), the detection and the release may be repeated. VDD Reverse Detector VDD Reverse Detector IOUT VOUT VOUT Vref Vref CE GND CE GND Fig.2 Reverse Current Protection Mode VIN/VOUT [V] VIN VREV_ REL 35mV 30mV VREV_ DET VOUT IOUT IOUT/IREV Output/Reverse Current Input/Output Voltage Fig.1 Normal Mode Normal Mode Reverse Current Protection Mode Normal Mode 0 IREV Fig. 3 Reverse Current Protection Mode Detection/ Release & Reverse Current/ Output Current Characteristics 10 IREV RP108J NO.EA-203-150817 CONSTANT SLOPE CIRCUIT (RP108Jxx1B/xx1D) RP108Jxx1B/xx1D has a Constant Slope Circuit (soft-start circuit) which allows the output voltage to start-up gradually. The capacitor to create the start-up slope is built-in the IC so that it does not require any external components. The upper limit of inrush current during the start-up is controlled by the short current ISC and the output current limit ILIM. In the following characteristics COUT = 10 F (RLOAD = 380), the inrush current IRUSH is not controlled by the short current ISC and the output current limit ILIM. Therefore the output voltage rises with the soft-start time (TSLOPE) set inside IC, and it enables to control the overshoot of the output voltage and the inrush current. TSLOPE is typ. 180 s. In the characteristics COUT = 20 F, IRUSH at the low output voltage is controlled by the short current ISC. After the current is released from ISC, the output voltage rises with the soft-start time (TSLOPE). In the characteristics COUT = 100 F, IRUSH at the low output voltage is controlled by the short current ISC. After the current is released from ISC, it is controlled by the output current limit. The output voltage rises with the soft-start time (TSLOPE) or longer. The relation of the inrush current and the constant slope depends on the output voltage since the inrush current is a sum of the charge current of COUT and the load current. Use RP108Jxx1E/xx1F to avoid an influence on peripheral components due to the inrush current generated in the use environment conditions (COUT and output voltage). RP108J381B/D Inrush current characteristics CIN=4.7F, COUT=10F, Topt=25C, RLOAD=380 CIN=4.7F, COUT=20F, Topt=25C, RLOAD=380 CIN=4.7F, COUT=100F, Topt=25C, RLOAD=380 11 RP108J NO.EA-203-150817 CONSTANT SLOPE CIRCUIT (RP108Jxx1E/xx1F) RP108Jxx1E/xx1F has a constant slope circuit (soft-start circuit) which allows the output voltage to start-up gradually. The capacitor to create the start-up slope is built-in the IC so that it does not require any external components. The upper limit of inrush current during the start-up is controlled by the output current limit ILIM. As shown in the following Foldback Characteristics, the inrush current is not controlled by the short current ISC during the soft-start time at the start-up. Therefore the output voltage rises with the soft-start time (TSLOPE) set inside IC, and it enables to control the overshoot of the output voltage and the inrush current. TSLOPE is typ. 570 s (max. 900 s/85C). Use RP108Jxx1B/xx1D to avoid an influence on peripheral components due to the output start-up time is slow in the system. In the characteristics COUT = 20 F, the inrush current is lower or equal to the output current limit ILIM. The output voltage rises with the soft-start time (TSLOPE). Similarly in the characteristics COUT = 100 F, the inrush current is lower or equal to the output current limit ILIM. The output voltage rises with the soft-start time (TSLOPE). The relation of the inrush current and the constant slope depends on the output voltage since the inrush current is a sum of the charge current of COUT and the load current. RP108J381E/F Inrush current characteristics Foldback Characteristics (Diagrammatic sketch) CIN=4.7F, COUT=20F, Topt=25C, RLOAD=380 12 CIN=4.7F, COUT=100F, Topt=25C, RLOAD=380 RP108J NO.EA-203-150817 PACKAGE INFORMATION Power Dissipation (TO-252-5-P2) Power Dissipation (PD) depends on conditions of mounting on board. This specification is based on the Measurement Conditions below. Measurement conditions Ultra High Wattage Land Pattern Environment Standard Land Pattern Mounting on board (Wind velocity 0m/s) Board Material Glass cloth epoxy plastic (Four-layers) Glass cloth epoxy plastic (Double layers) Board Dimensions 76.2mm x 114.3mm x 0.8mm 50mm x 50mm x 1.6mm Copper Ratio Top, Back side: 50mm Square, Approx.96%, 2nd, 3rd Layer: 50mm Square, Approx.100% Top side: Approx. 50%, Back side: Approx. 50% Through - Hole 0.4mm x 30pcs 0.5mm x 24pcs Measurement Results (Ta= 25C, Tjmax=125C) Ultra High Wattage Land Pattern Standard Land Pattern 3800mW 1900mW ja= (125-25C)/3.8W = 26C/W ja=(125-25C)/1.9W= 53C/W jc= 7C/W jc= 17C/W Power Dissipation Thermal Resistance 50 76.2 4800 50 3800 3000 50 40 4000 2000 50 On Board (Ultra High Wattage Land Pattern) 2350 114.3 Power Dissipation PD (mW) 5000 1900 1000 0 0 On Board 25 50 Standard 7585 100 125 150 Ambient Temperature (C) Power Dissipation Ultra High Wattage Measurement Board Pattern IC Mount Area (Unit: mm) The above graph shows the Power Dissipation of the package based on Tjmax= 125C and Tjmax=150C. Operating the IC in the shaded area in the graph might have an influence its lifetime. Operating time must be within the time limit described in the table below, in case of operating in the shaded area. Operating Time Estimated years (Operating 4 hours/day) 13,000 hours 9 years 13 RP108J NO.EA-203-150817 PACKAGE DIMENSIONS (TO-252-5-P2) 6.600.20 5 2.700.20 +0.26 (08) 1.52 -0.13 (6.20) 0.500.10 0.10 0.500.10 0.12 M 1.27 (3.56) (5.04) (4.06) The tab on the bottom of the package enhances thermal performance and is electrically connected to GND (substrate level). It is recommended that the tab be connected to the ground plane on the board, or otherwise be left floating. R0.325 (1.50) (4.19) * 0.500.10 2.300.20 (1.00) 1.100.20 9.900.30 (00.127) S 1 6.100.20 C0.60 5.340.20 (1.00) * R0.225 (Unit: mm) MARK SPECIFICATION (TO-252-5-P2) 14 : Product Code...Refer to MARK SPECIFICATION TABLE : Lot Number ... Alphanumeric Serial Number RP108J NO.EA-203-150817 RP108J Mark Specification Table (TO-252-5-P2) RP108Jxx1B Part Number RP108Jxx1D VSET Part Number VSET RP108J081B RP108J091B RP108J101B E1J081B E1J091B E1J101B 0.8V 0.9V 1.0V RP108J081D RP108J091D RP108J101D E1J081D E1J091D E1J101D 0.8V 0.9V 1.0V RP108J111B RP108J121B RP108J131B RP108J141B RP108J151B RP108J161B RP108J171B RP108J181B RP108J191B RP108J201B RP108J211B RP108J221B RP108J231B RP108J241B RP108J251B RP108J261B RP108J271B RP108J281B E1J111B E1J121B E1J131B E1J141B E1J151B E1J161B E1J171B E1J181B E1J191B E1J201B E1J211B E1J221B E1J231B E1J241B E1J251B E1J261B E1J271B E1J281B 1.1V 1.2V 1.3V 1.4V 1.5V 1.6V 1.7V 1.8V 1.9V 2.0V 2.1V 2.2V 2.3V 2.4V 2.5V 2.6V 2.7V 2.8V RP108J111D RP108J121D RP108J131D RP108J141D RP108J151D RP108J161D RP108J171D RP108J181D RP108J191D RP108J201D RP108J211D RP108J221D RP108J231D RP108J241D RP108J251D RP108J261D RP108J271D RP108J281D E1J111D E1J121D E1J131D E1J141D E1J151D E1J161D E1J171D E1J181D E1J191D E1J201D E1J211D E1J221D E1J231D E1J241D E1J251D E1J261D E1J271D E1J281D 1.1V 1.2V 1.3V 1.4V 1.5V 1.6V 1.7V 1.8V 1.9V 2.0V 2.1V 2.2V 2.3V 2.4V 2.5V 2.6V 2.7V 2.8V RP108J291B RP108J301B RP108J311B RP108J321B RP108J331B RP108J341B RP108J351B RP108J361B RP108J371B RP108J381B RP108J391B RP108J401B RP108J411B RP108J421B RP108J121B5 RP108J181B5 RP108J281B5 E1J291B E1J301B E1J311B E1J321B E1J331B E1J341B E1J351B E1J361B E1J371B E1J381B E1J391B E1J401B E1J411B E1J421B E1J121B5 E1J181B5 E1J281B5 2.9V 3.0V 3.1V 3.2V 3.3V 3.4V 3.5V 3.6V 3.7V 3.8V 3.9V 4.0V 4.1V 4.2V 1.25V 1.85V 2.85V RP108J291D RP108J301D RP108J311D RP108J321D RP108J331D RP108J341D RP108J351D RP108J361D RP108J371D RP108J381D RP108J391D RP108J401D RP108J411D RP108J421D RP108J121D5 RP108J181D5 RP108J281D5 E1J291D E1J301D E1J311D E1J321D E1J331D E1J341D E1J351D E1J361D E1J371D E1J381D E1J391D E1J401D E1J411D E1J421D E1J121D5 E1J181D5 E1J281D5 2.9V 3.0V 3.1V 3.2V 3.3V 3.4V 3.5V 3.6V 3.7V 3.8V 3.9V 4.0V 4.1V 4.2V 1.25V 1.85V 2.85V 15 RP108J NO.EA-203-150817 RP108Jxx1E Part Number 16 RP108Jxx1F VSET Part Number VSET RP108J081E RP108J091E RP108J101E E1J081E E1J091E E1J101E 0.8V 0.9V 1.0V RP108J081F RP108J091F RP108J101F E1J081F E1J091F E1J101F 0.8V 0.9V 1.0V RP108J111E RP108J121E RP108J131E E1J111E E1J121E E1J131E 1.1V 1.2V 1.3V RP108J111F RP108J121F RP108J131F E1J111F E1J121F E1J131F 1.1V 1.2V 1.3V RP108J141E RP108J151E RP108J161E RP108J171E RP108J181E RP108J191E RP108J201E RP108J211E RP108J221E RP108J231E RP108J241E RP108J251E RP108J261E RP108J271E RP108J281E E1J141E E1J151E E1J161E E1J171E E1J181E E1J191E E1J201E E1J211E E1J221E E1J231E E1J241E E1J251E E1J261E E1J271E E1J281E 1.4V 1.5V 1.6V 1.7V 1.8V 1.9V 2.0V 2.1V 2.2V 2.3V 2.4V 2.5V 2.6V 2.7V 2.8V RP108J141F RP108J151F RP108J161F RP108J171F RP108J181F RP108J191F RP108J201F RP108J211F RP108J221F RP108J231F RP108J241F RP108J251F RP108J261F RP108J271F RP108J281F E1J141F E1J151F E1J161F E1J171F E1J181F E1J191F E1J201F E1J211F E1J221F E1J231F E1J241F E1J251F E1J261F E1J271F E1J281F 1.4V 1.5V 1.6V 1.7V 1.8V 1.9V 2.0V 2.1V 2.2V 2.3V 2.4V 2.5V 2.6V 2.7V 2.8V RP108J291E RP108J301E RP108J311E RP108J321E RP108J331E E1J291E E1J301E E1J311E E1J321E E1J331E 2.9V 3.0V 3.1V 3.2V 3.3V RP108J291F RP108J301F RP108J311F RP108J321F RP108J331F E1J291F E1J301F E1J311F E1J321F E1J331F 2.9V 3.0V 3.1V 3.2V 3.3V RP108J341E RP108J351E RP108J361E RP108J371E RP108J381E RP108J391E RP108J401E RP108J411E RP108J421E RP108J121E5 RP108J181E5 RP108J281E5 E1J341E E1J351E E1J361E E1J371E E1J381E E1J391E E1J401E E1J411E E1J421E E1J121E5 E1J181E5 E1J281E5 3.4V 3.5V 3.6V 3.7V 3.8V 3.9V 4.0V 4.1V 4.2V 1.25V 1.85V 2.85V RP108J341F RP108J351F RP108J361F RP108J371F RP108J381F RP108J391F RP108J401F RP108J411F RP108J421F RP108J121F5 RP108J181F5 RP108J281F5 E1J341F E1J351F E1J361F E1J371F E1J381F E1J391F E1J401F E1J411F E1J421F E1J121F5 E1J181F5 E1J281F5 3.4V 3.5V 3.6V 3.7V 3.8V 3.9V 4.0V 4.1V 4.2V 1.25V 1.85V 2.85V RP108J NO.EA-203-150817 TEST CIRCUITS Fixed Output Voltage Type (RP108Jxx1x) VDD VOUT RP108Jxx1x C1 C2 VFB CE V VOUT IOUT GND C1=Ceramic 10F C2=Ceramic 10F Basic Test Circuit VDD VOUT VOUT RP108Jxx1x A ISS C1 VFB CE C2 GND C1=Ceramic 10F C2=Ceramic 10F Test Circuit for Supply Current VDD VOUT VOUT RP108Jxx1x A ISS C1 VFB CE C2 GND C1=Ceramic 10F C2=Ceramic 10F Test Circuit for Standby Current 17 RP108J NO.EA-203-150817 Adjustable Output Voltage Setting Type (RP108J081x) VDD DD VOUT OUT R1 C2 RP108J081x RP132x SeriesVFB C1 V VOUT IOUT R2 CE GND C1=Ceramic 10F C2=Ceramic 10F Basic Test Circuit VDD DD A ISS C1 VOUT VOUT OUT RP108J081x RP132x SeriesVFB R1 C2 R2 CE GND C1=Ceramic 10F C2=Ceramic 10F Test Circuit for Supply Current VDD DD A ISS C1 VOUT VOUT OUT RP108J081x RP132x SeriesVFB R1 C2 R2 CE GND C1=Ceramic 10F C2=Ceramic 10F Test Circuit for Standby Current Note : Refer to Adjustable Output Voltage Type Settings for R1 and R2. 18 RP108J NO.EA-203-150817 TYPICAL CHARACTERISTICS Note: Typical Characteristics are intended to be used as reference data; they are not guaranteed. 1) Output Voltage vs. Input Voltage (C1=C2=Ceramic10F, Ta=25C) RP108J081x 1.8 0.9 0.7 Output Voltage V OUT (V) Output Voltage V OUT (V) 0.8 0.6 0.5 0.4 Iout=1mA 0.3 Iout=100mA 0.2 Iout=1A 0.1 0 0 1 2 3 4 1.5 1.2 0.9 Iout=1mA Iout=100mA 0.6 Iout=1A 0.3 0 5 0 Input Voltage V IN (V) 1 2.8 4.9 Output Voltage V OUT (V) 5.6 2.4 2 Iout=1mA 1.2 Iout=100mA 0.8 3 4 5 RP108J421x 3.2 1.6 2 Input Voltage V IN (V) RP108J281x Output Voltage V OUT (V) RP108J151x Iout=1A 0.4 4.2 3.5 2.8 2.1 Iout=1mA 1.4 Iout=100mA 0.7 0 Iout=1A 0 0 1 2 3 Input Voltage V IN (V) 4 5 0 1 2 3 4 5 Input Voltage V IN (V) 19 RP108J NO.EA-203-150817 2Output Voltage vs. Temperature (C1=C2=Ceramic10F, -40C Ta 85C RP108J151x 0.84 1.54 0.83 1.53 Output Voltage V OUT (V) Output Voltage V OUT (V) RP108J081x 0.82 0.81 0.80 0.79 0.78 1.52 1.51 1.50 1.49 1.48 0.77 1.47 0.76 1.46 -40 -25 50 0 25 Temperature Ta (C) 75 85 -40 -25 50 0 25 Temperature Ta (C) RP108J421x 2.88 4.28 2.86 4.26 Output Voltage V OUT (V) Output Voltage V OUT (V) RP108J281x 75 85 2.84 2.82 2.80 2.78 2.76 4.24 4.22 4.20 4.18 4.16 4.14 2.74 4.12 2.72 -40 -25 0 25 50 Temperature Ta (C) -40 -25 75 85 0 25 50 Temperature Ta (C) 75 85 3) Supply Current vs. Input Voltage (C1=C2=Ceramic 10F, IOUT=0A, Ta=25C) RP108J151x 450 450 400 400 Supply Current ISS (A) Supply Current ISS (A) RP108J081x 350 300 250 200 150 100 50 300 250 200 150 100 50 0 0 0 1 2 3 Input Voltage V IN (V) 20 350 4 5 0 1 2 3 Input Voltage V IN (V) 4 5 RP108J NO.EA-203-150817 RP108J421x 450 450 400 400 Supply Current ISS (A) Supply Current ISS (A) RP108J281x 350 300 250 200 150 100 50 350 300 250 200 150 100 50 0 0 0 1 2 3 4 5 0 1 Input Voltage V IN (V) 2 3 4 5 Input Voltage V IN (V) 4) Short Current Limit vs. Temperature/ Current Limit vs. Temperature RP108J includes a Fold-back Protection Circuit. Under conditions during a Fold-back Protection Circuit works, Thermal Shutdown Circuit starts to operate in order to prevent the self-heat generation. Therefore, RP108J isn't able to test "Output voltage vs. Output Current". RP108J081x RP108J081x 300 5000 Short Current Limit ILIM (mA) Current Limit ILIM (mA) 4500 4000 3500 3000 2500 280 260 240 220 200 2000 -40 -25 0 25 50 Temperature Ta (C) 75 85 -40 -25 0 25 50 Temperature Ta (C) 75 85 21 RP108J NO.EA-203-150817 5) Supply Current vs. Temperature (C1= C2=Ceramic 10F, IOUT=0mA) RP108J151x 400 400 390 390 380 380 Supply Current I ss (A) Supply Current Iss (A) RP108J081x 370 360 350 340 330 320 310 370 360 350 340 330 320 310 300 300 -40 -25 0 25 50 Temperature Ta (C) 75 85 -40 -25 25 50 0 Temperature Ta (C) 6) Dropout Voltage vs. Output Current (C1=C2=Ceramic 10F) RP108J251x Dropout Voltage V DIF (mV) 700 600 500 85 400 25 -40 300 200 100 0 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 Output Current IOUT (A) 7) Dropout Voltage vs. Set Output Voltage (C1=C2=Ceramic 10F, Ta=25C) RP108J251x 900 800 Dropout Voltage [mV] 700 600 300mA 500 3A 400 300 200 100 0 0.5 1 1.5 2 2.5 3 VSET [V] 22 3.5 4 4.5 75 85 RP108J NO.EA-203-150817 8) Ripple Rejection vs. Input Voltage (C1=C2=10F, Ripple=0.2Vp-p, IOUT=100, Ta=25C) RP108J081x RP108J251x 90 80 80 Ripple Rejection (dB) 100 90 Ripple Rejection (dB) 100 70 60 50 40 0.1kHz 1kHz 10kHz 100kHz 30 20 10 70 60 50 0.1kHz 1kHz 10kHz 100kHz 40 30 20 10 0 0 1 2 3 4 5 2 3 Input Voltage V IN (V) 4 5 Input Voltage V IN (V) RP108J421x 100 Ripple Rejection (dB) 90 80 70 60 0.1kHz 1kHz 10kHz 100kHz 50 40 30 20 10 0 4.00 4.25 4.50 4.75 5.00 5.25 Input Voltage V IN (V) 9) Ripple Rejection vs. Frequency (C1=none, C2=10F, IOUT=100mA, Ta=25C) RP108J081x RP108J421x V IN=1.8V,Ripple=0.2Vp-p 120 100 Ripple Rejection (dB) 100 Ripple Rejection (dB) V IN=5.2V,Ripple=0.2Vp-p 120 80 60 40 20 80 60 40 20 0 0 0.1 1 10 Frequancy f (kHz) 100 1000 0.1 1 10 100 1000 Frequancy f (kHz) 23 RP108J NO.EA-203-150817 10) Input Transient Response (C1=none, C2=10F, IOUT=30mA, tr=tf=5s, Ta=25C) 3.0 4.22 6 0.83 2.5 4.21 5 2.0 Input Voltage 0.81 1.5 0.80 1.0 Output Voltage 0.78 -20 -10 0 0.5 0.0 4.19 3 Output Voltage 4.18 1 4.16 10 20 30 40 50 60 70 80 0 -0.2 -0.1 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 Time t (ms) 11) Load Transient Response (C1=C2=10F, tr=tf=0.5s, Ta=25C) RP108J081x 0.80 Output Voltage Output Voltage V IN=5.25V Output Voltage 20 40 60 80 100 120 140 160 Output Voltage V OUT (V) Output Voltage V OUT (V) 0.75 1000 4.18 Time t (s) 24 0.80 RP108J421x 0 0 0.85 RP108J421x 4.19 0 Output Current 1mA 3A Time t (ms) Output Current 100mA500mA 4.16 -40 -20 3 Time t (s) 500 6 0.70 -0.4 -0.2 0.0 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 20 40 60 80 100 120 140 160 V IN=5.25V 4.17 Output Voltage V OUT (V) 0 0.81 0.78 -40 -20 0 V IN=1.8V Output Current IOUT (mA) 500 Output Current 100mA 500mA RP108J081x 1000 Output Curren IOUT (mA) Output Voltage V OUT (V) V IN=1.8V 0.79 2 4.17 Time t (s) 0.82 4 Input Voltage Output Current IOUT (mA) 0.79 4.20 6 3 Output Current 1mA3A 4.25 4.20 4.15 Output Voltage 4.10 -0.4 -0.2 0.0 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 Time t (ms) 0 Output Current IOUT (mA) 0.82 Output Voltage VOUT (V) 0.84 Input Voltage VIN (V) RP108J421x Input Voltage VIN (V) Output Voltage VOUT (V) RP108J081x RP108J NO.EA-203-150817 12) Turn on Speed with CE pin (C1=C2=Ceramic 10F, Ta=25C) RP108J081B/D RP108J281B/D 13) Turn off Speed with CE pin (C1=C2=Ceramic 10F, Ta=25C) RP108J081D/F RP108J151B/D RP108J421B/D RP108J151D/F 25 RP108J NO.EA-203-150817 RP108J281D/F 14) Inrush Current RP108J081B/D 26 RP108J421D/F RP108J421B/D RP108J NO.EA-203-150817 ESR vs. Output Current When using the IC, consider the following points: The relations between IOUT (Output Current) and ESR of an output capacitor are shown below. The conditions when the white noise level is under 40V (Avg.) are marked as the hatched area in the graph. Measurement Conditions Frequency Band : 10Hz to 2MHz Temperature : -40C to 85C Hatched area : Noise level is under 40V C1, C2 :10.0F or more RP108J081x RP108J421x V IN=1.6V5.25V 100 V IN=4.2V5.25V 100 85C 85C -40C -40C 10 ESR () ESR () 10 1 0.1 1 0.1 0.01 0.01 0 1000 2000 Output Current IOUT (mA) 3000 0 1000 2000 Output Current IOUT (mA) 3000 27 1. The products and the product specifications described in this document are subject to change or discontinuation of production without notice for reasons such as improvement. Therefore, before deciding to use the products, please refer to Ricoh sales representatives for the latest information thereon. 2. The materials in this document may not be copied or otherwise reproduced in whole or in part without prior written consent of Ricoh. 3. Please be sure to take any necessary formalities under relevant laws or regulations before exporting or otherwise taking out of your country the products or the technical information described herein. 4. The technical information described in this document shows typical characteristics of and example application circuits for the products. The release of such information is not to be construed as a warranty of or a grant of license under Ricoh's or any third party's intellectual property rights or any other rights. 5. The products listed in this document are intended and designed for use as general electronic components in standard applications (office equipment, telecommunication equipment, measuring instruments, consumer electronic products, amusement equipment etc.). Those customers intending to use a product in an application requiring extreme quality and reliability, for example, in a highly specific application where the failure or misoperation of the product could result in human injury or death (aircraft, spacevehicle, nuclear reactor control system, traffic control system, automotive and transportation equipment, combustion equipment, safety devices, life support system etc.) should first contact us. 6. We are making our continuous effort to improve the quality and reliability of our products, but semiconductor products are likely to fail with certain probability. In order to prevent any injury to persons or damages to property resulting from such failure, customers should be careful enough to incorporate safety measures in their design, such as redundancy feature, fire containment feature and fail-safe feature. We do not assume any liability or responsibility for any loss or damage arising from misuse or inappropriate use of the products. 7. Anti-radiation design is not implemented in the products described in this document. 8. The X-ray exposure can influence functions and characteristics of the products. Confirm the product functions and characteristics in the evaluation stage. 9. WLCSP products should be used in light shielded environments. The light exposure can influence functions and characteristics of the products under operation or storage. 10. There can be variation in the marking when different AOI (Automated Optical Inspection) equipment is used. In the case of recognizing the marking characteristic with AOI, please contact Ricoh sales or our distributor before attempting to use AOI. 11. Please contact Ricoh sales representatives should you have any questions or comments concerning the products or the technical information. Halogen Free Ricoh is committed to reducing the environmental loading materials in electrical devices with a view to contributing to the protection of human health and the environment. Ricoh has been providing RoHS compliant products since April 1, 2006 and Halogen-free products since April 1, 2012. https://www.e-devices.ricoh.co.jp/en/ Sales & Support Offices Ricoh Electronic Devices Co., Ltd. Shin-Yokohama Office (International Sales) 2-3, Shin-Yokohama 3-chome, Kohoku-ku, Yokohama-shi, Kanagawa, 222-8530, Japan Phone: +81-50-3814-7687 Fax: +81-45-474-0074 Ricoh Americas Holdings, Inc. 675 Campbell Technology Parkway, Suite 200 Campbell, CA 95008, U.S.A. Phone: +1-408-610-3105 Ricoh Europe (Netherlands) B.V. Semiconductor Support Centre Prof. W.H. Keesomlaan 1, 1183 DJ Amstelveen, The Netherlands Phone: +31-20-5474-309 Ricoh International B.V. - German Branch Semiconductor Sales and Support Centre Oberrather Strasse 6, 40472 Dusseldorf, Germany Phone: +49-211-6546-0 Ricoh Electronic Devices Korea Co., Ltd. 3F, Haesung Bldg, 504, Teheran-ro, Gangnam-gu, Seoul, 135-725, Korea Phone: +82-2-2135-5700 Fax: +82-2-2051-5713 Ricoh Electronic Devices Shanghai Co., Ltd. Room 403, No.2 Building, No.690 Bibo Road, Pu Dong New District, Shanghai 201203, People's Republic of China Phone: +86-21-5027-3200 Fax: +86-21-5027-3299 Ricoh Electronic Devices Shanghai Co., Ltd. Shenzhen Branch 1205, Block D(Jinlong Building), Kingkey 100, Hongbao Road, Luohu District, Shenzhen, China Phone: +86-755-8348-7600 Ext 225 Ricoh Electronic Devices Co., Ltd. Taipei office Room 109, 10F-1, No.51, Hengyang Rd., Taipei City, Taiwan (R.O.C.) Phone: +886-2-2313-1621/1622 Fax: +886-2-2313-1623