B32634B1153J010 - EPCOS AG

Film Capacitors

Metallized Polypropylene Film Capacitors (MFP)

Series/Type: B32632 ... B32634

Date: May 2009

information contained therein without EPCOS' prior express consent is prohibited.

Typical applications

Smoothing

High-frequency AC loads

Switch-mode power supplies

Electronic ballasts

HID lamps

Climatic

Max. operating temperature: 110 °C

Climatic category (IEC 60068-1): 55/100/56

Construction

Dielectric: polypropylene (PP)

Film metallized on one side and

metal foils internally connected in series

Contact layer of sprayed metal

Wound capacitor technology

Epoxy resin coating (UL 94 V-0)

Features

Highest possible contact reliability

Very high pulse strength

Self-healing properties

Terminals

Crimped wire leads, lead-free tinned,

lead length (6 1 mm)

Double crimped wire leads, lead-free tinned

Straight wire leads, lead-free tinned,

lead length (17 ±3 mm)

Different lead spacings (reduced and enlarged) available,

lead length (6 1 mm)

Marking

Manufacturer's logo, style and type (P63x),

rated capacitance (coded),

capacitance tolerance (code letter),

rated DC voltage, date of manufacture (coded)

Delivery mode

Bulk (untaped)

Taped (Ammo pack or reel)

For notes on taping, refer to chapter "Taping and packing“.

Metallized polypropylene film capacitors (MFP) B32632 ... B32634

Very high pulse (wound)

Page 2 of 29Please read Cautions and warnings and

Important notes at the end of this document.

Dimensional drawings

Detail of double crimped version

Dimensions in mm

Lead spacing

±0.8

Lead diameter

Type

15.0 0.8 B32632

22.5 0.8 B32633

27.5 0.8 B32634

B32632 ... B32634

Very high pulse (wound)

Page 3 of 29Please read Cautions and warnings and

Important notes at the end of this document.

Overview of available types

Lead configurations

Series Standard Reduced Straight Double crimped

B32632 15 mm 7.5 / 10 / 12.5 mm 15 mm 15 mm

B32633 22.5 mm 15 / 17.5 / 20 mm 22.5 mm 22.5 mm

B32634 27.5 mm 25 mm 27.5 mm 27.5 mm

Lead spacing 15.0 mm 22.5 mm

Type B32632 B32633

VR(V DC) 630 1250 1600 2000 3000 630 1250 1600 2000 2500 3000

VRMS (V AC) 300 450 450 500 750 300 450 450 500 750 750

CR(nF)

0.47

0.68

1.0

1.5

2.2

3.3

4.7

6.8

100

B32632 ... B32634

Very high pulse (wound)

Page 4 of 29Please read Cautions and warnings and

Important notes at the end of this document.

Overview of available types

Lead configurations

Series Standard Reduced Straight Double crimped

B32632 15 mm 7.5 / 10 / 12.5 mm 15 mm 15 mm

B32633 22.5 mm 15 / 17.5 / 20 mm 22.5 mm 22.5 mm

B32634 27.5 mm 25 mm 27.5 mm 27.5 mm

Lead spacing 27.5 mm

Type B32634

VR(V DC) 630 1250 1600 2000

VRMS (V AC) 300 450 450 500

CR(nF)

100

150

220

330

B32632 ... B32634

Very high pulse (wound)

Page 5 of 29Please read Cautions and warnings and

Important notes at the end of this document.

Ordering codes and packing units (lead spacing 15 mm)

V DC

VRMS

f≤1 kHz

V AC

Max. dimensions

w×h×l

Ordering code

(composition see

below)

Ammo

pack

pcs./MOQ

Reel

pcs./MOQ

Untaped

pcs./MOQ

MOQ = Minimum Order Quantity, consisting of 4 packing units.

B32632B2471M*** and B32632B2681M*** are only available in M tolerance.

B32632B4471K*** and B32632B4681K*** are only available in K tolerance.

Further E series and intermediate capacitance values on request.

Composition of ordering code

+ = Capacitance tolerance code: *** = Packaging code:

M = ±20%

K = ±10%

J = ±5%

289 = Ammo pack

189 = Reel

010 = Untaped crimped (lead length 6 1 mm)

008 = Untaped straight (lead length 17±3 mm)

020 = Double crimped (lead length 6 1 mm)

Packaging codes for further lead configurations (untaped):

Lead configuration (lead length 6 1 mm) Reduced Reduced Reduced Enlarged

Lead spacing (mm) 7.5 mm 10 mm 12.5 mm 17.5 mm

Packaging code 030 040 050 060

630 300 2.2 6.0 ×11.5 ×18.5 B32632B6222+*** 3600 4800 4000

3.3 6.0 ×11.5 ×18.5 B32632B6332+*** 3600 4800 4000

4.7 6.0 ×11.5 ×18.5 B32632B6472+*** 3600 4800 4000

6.8 6.0 ×11.5 ×18.5 B32632B6682+*** 3600 4800 4000

10 6.0 ×11.5 ×18.5 B32632B6103+*** 3600 4800 4000

15 6.5 ×12.0 ×18.5 B32632B6153+*** 3200 4000 4000

22 7.5 ×13.5 ×18.5 B32632B6223+*** 2800 3600 4000

33 9.0 ×15.0 ×18.5 B32632B6333+*** 2400 3200 2000

47 11.0 ×16.5 ×18.5 B32632B6473+*** 1800 2400 2000

1250 450 1.0 6.0 ×11.5 ×18.5 B32632B7102+*** 3400 4400 4000

1.5 6.0 ×11.5 ×18.5 B32632B7152+*** 3400 4400 4000

2.2 6.5 ×12.0 ×18.5 B32632B7222+*** 3400 4400 4000

3.3 6.5 ×12.0 ×18.5 B32632B7332+*** 3200 4000 4000

4.7 7.0 ×12.5 ×18.5 B32632B7472+*** 3200 4000 4000

6.8 7.5 ×14.0 ×18.5 B32632B7682+*** 3000 4000 4000

10 9.0 ×15.0 ×18.5 B32632B7103+*** 2400 3200 2000

15 11.5 ×16.5 ×18.5 B32632B7153+*** 1800 2400 2000

B32632

Very high pulse (wound)

Page 6 of 29Please read Cautions and warnings and

Important notes at the end of this document.

Ordering codes and packing units (lead spacing 15 mm)

V DC

VRMS

f≤1 kHz

V AC

Max. dimensions

w×h×l

Ordering code

(composition see

below)

Ammo

pack

pcs./MOQ

Reel

pcs./MOQ

Untaped

pcs./MOQ

MOQ = Minimum Order Quantity, consisting of 4 packing units.

B32632B2471M*** and B32632B2681M*** are only available in M tolerance.

B32632B4471K*** and B32632B4681K*** are only available in K tolerance.

Further E series and intermediate capacitance values on request.

Composition of ordering code

+ = Capacitance tolerance code: *** = Packaging code:

M = ±20%

K = ±10%

J = ±5%

289 = Ammo pack

189 = Reel

010 = Untaped crimped (lead length 6 1 mm)

008 = Untaped straight (lead length 17±3 mm)

020 = Double crimped (lead length 6 1 mm)

Packaging codes for further lead configurations (untaped):

Lead configuration (lead length 6 1 mm) Reduced Reduced Reduced Enlarged

Lead spacing (mm) 7.5 mm 10 mm 12.5 mm 17.5 mm

Packaging code 030 040 050 060

1600 450 1.0 6.0 ×11.5 ×18.5 B32632B1102+*** 3600 4800 4000

1.5 6.0 ×11.5 ×18.5 B32632B1152+*** 3600 4800 4000

2.2 6.5 ×12.0 ×18.5 B32632B1222+*** 3200 4000 4000

3.3 7.5 ×13.0 ×18.5 B32632B1332+*** 2800 3600 4000

4.7 8.5 ×14.0 ×18.5 B32632B1472+*** 2400 3200 4000

6.8 9.5 ×15.0 ×18.5 B32632B1682+*** 2000 2800 2000

10 11.5 ×17.0 ×18.5 B32632B1103+*** 1800 2400 2000

2000 500 0.47 6.5 ×11.5 ×18.5 B32632B2471M*** 3400 4400 4000

0.68 6.5 ×12.0 ×18.5 B32632B2681M*** 3400 4400 4000

1.0 6.5 ×12.0 ×18.5 B32632B2102+*** 3400 4400 4000

1.5 6.5 ×12.0 ×18.5 B32632B2152+*** 3400 4400 4000

2.2 7.0 ×13.0 ×18.5 B32632B2222+*** 2400 4000 2000

3.3 8.5 ×14.5 ×18.5 B32632B2332+*** 2600 3400 2000

4.7 10.0 ×16.0 ×18.5 B32632B2472+*** 2000 2800 2000

6.8 12.0 ×17.5 ×18.5 B32632B2682+*** 1800 2400 2000

3000 750 0.47 6.5 ×11.5 ×18.5 B32632B4471K*** 4000 5200 4000

0.68 7.0 ×13.0 ×18.5 B32632B4681K*** 3600 4800 4000

1.0 8.5 ×14.0 ×18.5 B32632B4102+*** 3000 4000 2000

1.5 9.5 ×16.5 ×18.5 B32632B4152+*** 2600 3400 2000

2.2 12.0 ×17.5 ×18.5 B32632B4222+*** 2000 2800 2000

B32632

Very high pulse (wound)

Page 7 of 29Please read Cautions and warnings and

Important notes at the end of this document.

Ordering codes and packing units (lead spacing 22.5 mm)

V DC

VRMS

f≤1 kHz

V AC

Max. dimensions

w×h×l

Ordering code

(composition see

below)

Ammo

pack

pcs./MOQ

Reel

pcs./MOQ

Untaped

pcs./MOQ

MOQ = Minimum Order Quantity, consisting of 4 packing units.

Further E series and intermediate capacitance values on request.

Composition of ordering code

+ = Capacitance tolerance code: *** = Packaging code:

K = ±10%

J = ±5%

289 = Ammo pack

189 = Reel

010 = Untaped crimped (lead length 6 1 mm)

008 = Untaped straight (lead length 17±3 mm)

020 = Double crimped (lead length 6 1 mm)

Packaging codes for further lead configurations (untaped):

Lead configuration (lead length 6 1 mm) Reduced Reduced Reduced Enlarged

Lead spacing (mm) 15 mm 17.5 mm 20 mm 25 mm

Packaging code 055 060 070 080

630 300 22 6.5 ×12.0 ×27.0 B32633B6223+*** 2200 3000 4000

33 7.0 ×14.0 ×27.0 B32633B6333+*** 2000 2800 2000

47 7.5 ×14.5 ×27.0 B32633B6473+*** 1800 2400 2000

68 9.0 ×16.0 ×27.0 B32633B6683+*** 1400 2000 2000

100 10.5 ×18.5 ×27.0 B32633B6104+*** 1200 1600 1000

1250 450 10 7.0 ×14.0 ×27.0 B32633B7103+*** 2000 2800 2000

15 8.0 ×15.5 ×27.0 B32633B7153+*** 1800 2400 2000

22 9.5 ×16.5 ×27.0 B32633B7223+*** 1400 2000 2000

33 11.5 ×19.0 ×27.0 B32633B7333+*** 1200 1600 1000

47 13.5 ×20.5 ×27.0 B32633B7473+*** 1000 1400 1000

1600 450 3.3 6.5 ×12.5 ×27.0 B32633B1332+*** 2000 2800 4000

4.7 6.5 ×12.5 ×27.0 B32633B1472+*** 2000 2800 4000

6.8 7.0 ×14.5 ×27.0 B32633B1682+*** 2000 2400 2000

10 8.0 ×15.5 ×27.0 B32633B1103+*** 1800 2600 2000

15 9.5 ×17.0 ×27.0 B32633B1153+*** 1400 2000 1000

22 11.5 ×19.0 ×27.0 B32633B1223+*** 1200 1600 1000

33 14.5 ×22.0 ×27.0 B32633B1333+*** 1000 1200 1000

2000 500 2.2 6.5 ×13.0 ×27.0 B32633B2222+*** 2000 2800 4000

3.3 6.5 ×13.0 ×27.0 B32633B2332+*** 2000 2800 4000

4.7 7.0 ×14.5 ×27.0 B32633B2472+*** 2000 2800 2000

6.8 8.5 ×16.0 ×27.0 B32633B2682+*** 1600 2200 2000

10 10.0 ×17.0 ×27.0 B32633B2103+*** 1400 1800 1000

15 12.0 ×19.5 ×27.0 B32633B2153+*** 1000 1400 1000

22 14.5 ×22.0 ×27.0 B32633B2223+*** 800 1200 1000

B32633

Very high pulse (wound)

Page 8 of 29Please read Cautions and warnings and

Important notes at the end of this document.

Ordering codes and packing units (lead spacing 22.5 mm)

V DC

VRMS

f≤1 kHz

V AC

Max. dimensions

w×h×l

Ordering code

(composition see

below)

Ammo

pack

pcs./MOQ

Reel

pcs./MOQ

Untaped

pcs./MOQ

MOQ = Minimum Order Quantity, consisting of 4 packing units.

Further E series and intermediate capacitance values on request.

Composition of ordering code

+ = Capacitance tolerance code: *** = Packaging code:

K = ±10%

J = ±5%

289 = Ammo pack

189 = Reel

010 = Untaped crimped (lead length 6 1 mm)

008 = Untaped straight (lead length 17±3 mm)

020 = Double crimped (lead length 6 1 mm)

Packaging codes for further lead configurations (untaped):

Lead configuration (lead length 6 1 mm) Reduced Reduced Reduced Enlarged

Lead spacing (mm) 15 mm 17.5 mm 20 mm 25 mm

Packaging code 055 060 070 080

2500 750 1.0 7.0 ×13.5 ×27.0 B32633B3102+*** 1800 2600 4000

1.5 7.0 ×14.0 ×27.0 B32633B3152+*** 1800 2600 4000

2.2 7.5 ×15.0 ×27.0 B32633B3222+*** 1800 2400 2000

3.3 9.0 ×16.0 ×27.0 B32633B3332+*** 1400 2000 2000

4.7 10.0 ×18.0 ×27.0 B32633B3472+*** 1400 2000 2000

6.8 12.0 ×20.5 ×27.0 B32633B3682+*** 1200 1600 1000

10 14.0 ×23.0 ×27.0 B32633B3103+*** 1000 1400 1000

15 17.0 ×26.0 ×27.0 B32633B3153+*** 800 1200 800

3000 750 1.0 6.5 ×12.0 ×27.0 B32633B4102+*** 2600 3600 2000

1.5 7.5 ×13.5 ×27.0 B32633B4152+*** 2200 3000 2000

2.2 8.5 ×15.0 ×27.0 B32633B4222+*** 1800 2600 2000

3.3 10.0 ×17.0 ×27.0 B32633B4332+*** 1600 2200 2000

4.7 11.5 ×19.0 ×27.0 B32633B4472+*** 1200 1800 2000

6.8 13.0 ×22.0 ×27.0 B32633B4682+*** 1000 1400 800

B32633

Very high pulse (wound)

Page 9 of 29Please read Cautions and warnings and

Important notes at the end of this document.

Ordering codes and packing units (lead spacing 27.5 mm)

V DC

VRMS

f≤1 kHz

V AC

Max. dimensions

w×h×l

Ordering code

(composition see

below)

Untaped

pcs./MOQ

MOQ = Minimum Order Quantity, consisting of 4 packing units.

Further E series and intermediate capacitance values on request.

Composition of ordering code

+ = Capacitance tolerance code: *** = Packaging code:

K = ±10%

J = ±5%

010 = Untaped crimped (lead length 6 1 mm)

008 = Untaped straight (lead length 17±3 mm)

020 = Double crimped (lead length 6 1 mm)

Packaging codes for further lead configurations (untaped):

Lead configuration (lead length 6 1 mm) Reduced

Lead spacing (mm) 25 mm

Packaging code 090

630 300 100 9.5 ×18.0 ×32.0 B32634B6104+*** 1000

150 11.5 ×20.5 ×32.0 B32634B6154+*** 800

220 13.5 ×22.5 ×32.0 B32634B6224+*** 800

330 16.0 ×25.5 ×32.0 B32634B6334+*** 600

1250 450 33 9.5 ×18.0 ×32.0 B32634B7333+*** 1000

47 11.5 ×20.0 ×32.0 B32634B7473+*** 1000

68 13.0 ×23.0 ×32.0 B32634B7683+*** 800

100 16.0 ×26.0 ×32.0 B32634B7104+*** 600

1600 450 15 8.5 ×17.0 ×32.0 B32634B1153+*** 2000

22 10.0 ×18.5 ×32.0 B32634B1223+*** 1000

33 12.0 ×21.5 ×32.0 B32634B1333+*** 1000

47 14.0 ×22.5 ×32.0 B32634B1473+*** 800

68 16.0 ×25.5 ×32.0 B32634B1683+*** 600

2000 500 10 8.5 ×17.0 ×32.0 B32634A2103+*** 2000

15 10.0 ×19.5 ×32.0 B32634A2153+*** 1000

22 12.0 ×21.5 ×32.0 B32634A2223+*** 1000

33 15.0 ×24.0 ×32.0 B32634A2333+*** 800

B32634

Very high pulse (wound)

Page 10 of 29Please read Cautions and warnings and

Important notes at the end of this document.

Technical data

Operating temperature range Max. operating temperature Top,max +110 °C

Upper category temperature Tmax +100 °C

Lower category temperature Tmin 55 °C

Rated temperature TR+85 °C

Dissipation factor tan δ1.0 10-3 (at 10 kHz)

at 20 °C 2.0 10-3 (at 100 kHz)

(upper limit values)

Insulation resistance Rins 100 GΩ

at 20 °C, rel. humidity ≤65%

(minimum as-delivered values)

DC test voltage 2.0 VR,2s

(B32632/3000 V DC: 1.2 VR, 2 s;

B32633/3000 V DC: 1.6 VR, 2 s)

Category voltage VCTA(°C) DC voltage derating AC voltage derating

(continuous operation with VDC TA≤85 VC= VRVC,RMS = VRMS

or VAC atf≤1 kHz) 85<TA≤100 VC= VR(165TA)/80 VC,RMS = VRMS (165TA)/80

Operating voltage Vop for TA(°C) DC voltage (max. hours) AC voltage (max. hours)

short operating periods TA≤85 Vop = 1.25 VC(2000 h) Vop = 1.0 VC,RMS (2000 h)

(VDC or VAC atf≤1 kHz) 85<TA≤100 Vop = 1.25 VC(1000 h) Vop = 1.0 VC,RMS (1000 h)

Damp heat test 56 days/40 °C/93% relative humidity

Limit values after damp Capacitance change ∆C/C≤2%

heat test Dissipation factor change ∆tan δ ≤ 1.0 10-3 (at 10 kHz)

Insulation resistance Rins ≥50% of minimum

as-delivered values

Reliability:

Failure rate λ1 fit (≤210-9/h) at 0.5 VR,40°C

Service life tSL 200 000 h at 1.0 VR,85°C

For conversion to other operating conditions and temperatures,

refer to chapter "Quality, 2 Reliability".

Failure criteria:

Total failure Short circuit or open circuit

Failure due to variation Capacitance change ∆C/C> 10%

of parameters Dissipation factor tan δ>4upper limit value

Insulation resistance Rins < 1500 MΩ

B32632 ... B32634

Very high pulse (wound)

Page 11 of 29Please read Cautions and warnings and

Important notes at the end of this document.

Pulse handling capability

"dV/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal

voltages, expressed in V/µs.

"k0" represents the maximum permissible pulse characteristic of the waveform applied to the

capacitor, expressed in V2/µs.

Note:

The values of dV/dt and k0provided below must not be exceeded in order to avoid damaging the

capacitor.

dV/dt values

Lead spacing 15 mm 22.5 mm 27.5 mm

VRVRMS

V DC V AC dV/dt in V/µs

630 300 6 000 3 600 2 400

1250 450 14 400 8 400 5 400

1600 450 16 800 10 800 6 600

2000 500 20 400 14 400 8 400

2500 750 16 800 

3000 750 21 600 18 000 

k0values

Lead spacing 15 mm 22.5 mm 27.5 mm

VRVRMS

V DC V AC k0in V2/µs

630 300 7 560 000 4 536 000 3 024 000

1250 450 36 000 000 21 000 000 13 500 000

1600 450 53 760 000 34 560 000 21 120 000

2000 500 81 600 000 57 600 000 33 600 000

2500 750 84 000 000 

3000 750 129 600 000 108 000 000 

B32632 ... B32634

Very high pulse (wound)

Page 12 of 29Please read Cautions and warnings and

Important notes at the end of this document.

Impedance Z versus frequency f

(typical values)

B32632 ... B32634

Very high pulse (wound)

Page 13 of 29Please read Cautions and warnings and

Important notes at the end of this document.

Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA≤90 °C)

For TA>90 °C, please refer to "General technical information", section 3.2.3.

Lead spacing 15 mm

630 V DC/300 V AC 1250 V DC/450 V AC

1600 V DC/450 V AC 2000 V DC/500 V AC

B32632

Very high pulse (wound)

Page 14 of 29Please read Cautions and warnings and

Important notes at the end of this document.

Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA≤90 °C)

For TA>90 °C, please refer to "General technical information", section 3.2.3.

Lead spacing 15 mm

3000 V DC/750 V AC

B32632

Very high pulse (wound)

Page 15 of 29Please read Cautions and warnings and

Important notes at the end of this document.

Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA≤90 °C)

For TA>90 °C, please refer to "General technical information", section 3.2.3.

Lead spacing 22.5 mm

630 V DC/300 V AC 1250 V DC/450 V AC

1600 V DC/450 V AC 2000 V DC/500 V AC

B32633

Very high pulse (wound)

Page 16 of 29Please read Cautions and warnings and

Important notes at the end of this document.

Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA≤90 °C)

For TA>90 °C, please refer to "General technical information", section 3.2.3.

Lead spacing 22.5 mm

2500 V DC/750 V AC 3000 V DC/750 V AC

B32633

Very high pulse (wound)

Page 17 of 29Please read Cautions and warnings and

Important notes at the end of this document.

Permissible AC voltage VRMS versus frequency f (for sinusoidal waveforms, TA≤90 °C)

For TA>90 °C, please refer to "General technical information", section 3.2.3.

Lead spacing 27.5 mm

630 V DC/300 V AC 1250 V DC/450 V AC

1600 V DC/450 V AC 2000 V DC/500 V AC

B32634

Very high pulse (wound)

Page 18 of 29Please read Cautions and warnings and

Important notes at the end of this document.

Mounting guidelines

1 Soldering

1.1 Solderability of leads

The solderability of terminal leads is tested to IEC 60068-2-20, test Ta, method 1.

Before a solderability test is carried out, terminals are subjected to accelerated ageing (to

IEC 60068-2-2, test Ba: 4 h exposure to dry heat at 155 °C). Since the ageing temperature is far

higher than the upper category temperature of the capacitors, the terminal wires should be cut off

from the capacitor before the ageing procedure to prevent the solderability being impaired by the

products of any capacitor decomposition that might occur.

Solder bath temperature 235 ±5°C

Soldering time 2.0 ±0.5 s

Immersion depth 2.0 +0/0.5 mm from capacitor body or seating plane

Evaluation criteria:

Visual inspection Wetting of wire surface by new solder ≥90%, free-flowing solder

1.2 Resistance to soldering heat

Resistance to soldering heat is tested to IEC 60068-2-20, test Tb, method 1A.

Conditions:

Series Solder bath temperature Soldering time

MKT boxed (except 2.5 ×6.5 ×7.2 mm)

coated

uncoated (lead spacing > 10 mm)

260 ±5°C 10 ±1 s

MFP

MKP (lead spacing > 7.5 mm)

MKT boxed (case 2.5 ×6.5 ×7.2 mm) 5±1 s

MKP

MKT

(lead spacing ≤7.5 mm)

uncoated (lead spacing ≤10 mm)

insulated (B32559)

<4s

recommended soldering

profile for MKT uncoated

(lead spacing ≤10 mm) and

insulated (B32559)

B32632 ... B32634

Very high pulse (wound)

Page 19 of 29Please read Cautions and warnings and

Important notes at the end of this document.

Immersion depth 2.0 +0/0.5 mm from capacitor body or seating plane

Shield Heat-absorbing board, (1.5 ±0.5) mm thick, between capacitor

body and liquid solder

Evaluation criteria:

Visual inspection No visible damage

∆C/C0

2% for MKT/MKP/MFP

5% for EMI suppression capacitors

tan δAs specified in sectional specification

B32632 ... B32634

Very high pulse (wound)

Page 20 of 29Please read Cautions and warnings and

Important notes at the end of this document.

1.3 General notes on soldering

Permissible heat exposure loads on film capacitors are primarily characterized by the upper cate-

gory temperature Tmax. Long exposure to temperatures above this type-related temperature limit

can lead to changes in the plastic dielectric and thus change irreversibly a capacitor's electrical

characteristics. For short exposures (as in practical soldering processes) the heat load (and thus

the possible effects on a capacitor) will also depend on other factors like:

Pre-heating temperature and time

Forced cooling immediately after soldering

Terminal characteristics:

diameter, length, thermal resistance, special configurations (e.g. crimping)

Height of capacitor above solder bath

Shadowing by neighboring components

Additional heating due to heat dissipation by neighboring components

Use of solder-resist coatings

The overheating associated with some of these factors can usually be reduced by suitable coun-

termeasures. For example, if a pre-heating step cannot be avoided, an additional or reinforced

cooling process may possibly have to be included.

EPCOS recommends the following conditions:

Pre-heating with a maximum temperature of 110 °C

Temperature inside the capacitor should not exceed the following limits:

MKP/MFP 110 °C

MKT 160 °C

When SMD components are used together with leaded ones, the leaded film capacitors should

not pass into the SMD adhesive curing oven. The leaded components should be assembled af-

ter the SMD curing step.

Leaded film capacitors are not suitable for reflow soldering.

Uncoated capacitors

For uncoated MKT capacitors with lead spacings ≤10 mm (B32560/B32561) the following mea-

sures are recommended:

pre-heating to not more than 110 °C in the preheater phase

rapid cooling after soldering

B32632 ... B32634

Very high pulse (wound)

Page 21 of 29Please read Cautions and warnings and

Important notes at the end of this document.

2 Cleaning

To determine whether the following solvents, often used to remove flux residues and other sub-

stances, are suitable for the capacitors described, refer to the table below:

Type Ethanol,

isopropanol,

n-propanol

n-propanol-water

mixtures,

water with surface

tension-reducing

tensides (neutral)

Solvent from

table A (see

next page)

Solvent from

table B (see

next page)

MKT

(uncoated)

Suitable Unsuitable In part suitable Unsuitable

MKT, MKP, MFP

(coated/boxed)

Suitable Suitable

Even when suitable solvents are used, a reversible change of the electrical characteristics may

occur in uncoated capacitors immediately after they are washed. Thus it is always recommended

to dry the components (e.g. 4 h at 70 °C) before they are subjected to subsequent electrical test-

ing.

Table A

Manufacturers' designations for trifluoro-trichloro-ethane-based cleaning solvents (selection)

Trifluoro-trichloro-

ethane

Mixtures of trifluoro-trichloro-ethane with ethanol and

isopropanol

Manufacturer

Freon TF Freon TE 35; Freon TP 35; Freon TES Du Pont

Frigen 113 TR Frigen 113 TR-E; Frigen 113 TR-P; Frigen TR-E 35 Hoechst

Arklone P Arklone A; Arklone L; Arklone K ICI

Kaltron 113 MDR Kaltron 113 MDA; Kaltron 113 MDI; Kaltron 113 MDI 35 Kali-Chemie

Flugene 113 Flugene 113 E; Flugene 113 IPA Rhone-Progil

Table B (worldwide banned substances)

Manufacturers' designations for unsuitable cleaning solvents (selection)

Mixtures of chlorinated hydrocarbons and ketones with fluorated hydrocarbons Manufacturer

Freon TMC; Freon TA; Freon TC Du Pont

Arklone E ICI

Kaltron 113 MDD; Kaltron 113 MDK Kali-Chemie

Flugene 113 CM Rhone-Progil

B32632 ... B32634

Very high pulse (wound)

Page 22 of 29Please read Cautions and warnings and

Important notes at the end of this document.

3 Embedding of capacitors in finished assemblies

In many applications, finished circuit assemblies are embedded in plastic resins. In this case,

both chemical and thermal influences of the embedding ("potting") and curing processes must be

taken into account.

Our experience has shown that the following potting materials can be recommended: non-flexible

epoxy resins with acid-anhydride hardeners; chemically inert, non-conducting fillers; maximum

curing temperature of 100 °C.

Caution:

Consult us first if you wish to embed uncoated types!

B32632 ... B32634

Very high pulse (wound)

Page 23 of 29Please read Cautions and warnings and

Important notes at the end of this document.

Cautions and warnings

Do not exceed the upper category temperature (UCT).

Do not apply any mechanical stress to the capacitor terminals.

Avoid any compressive, tensile or flexural stress.

Do not move the capacitor after it has been soldered to the PC board.

Do not pick up the PC board by the soldered capacitor.

Do not place the capacitor on a PC board whose PTH hole spacing differs from the specified

lead spacing.

Do not exceed the specified time or temperature limits during soldering.

Avoid external energy inputs, such as fire or electricity.

Avoid overload of the capacitors.

The table below summarizes the safety instructions that must always be observed. A detailed de-

scription can be found in the relevant sections of the chapters "General technical information" and

"Mounting guidelines".

Topic Safety information Reference chapter

"General technical

information"

Storage conditions Make sure that capacitors are stored within the

specified range of time, temperature and humidity

conditions.

4.5

"Storage conditions"

Flammability Avoid external energy, such as fire or electricity

(passive flammability), avoid overload of the

capacitors (active flammability) and consider the

flammability of materials.

5.3

"Flammability"

Resistance to

vibration

Do not exceed the tested ability to withstand

vibration. The capacitors are tested to

IEC 60068-2-6.

EPCOS offers film capacitors specially designed

for operation under more severe vibration regimes

such as those found in automotive applications.

Consult our catalog "Film Capacitors for

Automotive Electronics".

5.2

"Resistance to vibration"

B32632 ... B32634

Very high pulse (wound)

Page 24 of 29Please read Cautions and warnings and

Important notes at the end of this document.

Topic Safety information Reference chapter

"Mounting guidelines"

Soldering Do not exceed the specified time or temperature

limits during soldering.

1 "Soldering"

Cleaning Use only suitable solvents for cleaning capacitors. 2 "Cleaning"

Embedding of

capacitors in

finished assemblies

When embedding finished circuit assemblies in

plastic resins, chemical and thermal influences

must be taken into account.

Caution: Consult us first, if you also wish to

embed other uncoated component types!

3 "Embedding of

capacitors in finished

assemblies"

B32632 ... B32634

Very high pulse (wound)

Page 25 of 29Please read Cautions and warnings and

Important notes at the end of this document.

Symbols and terms

Symbol English German

αHeat transfer coefficient Wärmeübergangszahl

αCTemperature coefficient of capacitance Temperaturkoeffizient der Kapazität

A Capacitor surface area Kondensatoroberfläche

βCHumidity coefficient of capacitance Feuchtekoeffizient der Kapazität

C Capacitance Kapazität

CRRated capacitance Nennkapazität

∆C Absolute capacitance change Absolute Kapazitätsänderung

∆C/C Relative capacitance change (relative

deviation of actual value)

Relative Kapazitätsänderung (relative

Abweichung vom Ist-Wert)

∆C/CRCapacitance tolerance (relative deviation

from rated capacitance)

Kapazitätstoleranz (relative Abweichung

vom Nennwert)

dt Time differential Differentielle Zeit

∆t Time interval Zeitintervall

∆T Absolute temperature change

(self-heating)

Absolute Temperaturänderung

(Selbsterwärmung)

∆tan δAbsolute change of dissipation factor Absolute Änderung des Verlustfaktors

∆V Absolute voltage change Absolute Spannungsänderung

dV/dt Time differential of voltage function (rate

of voltage rise)

Differentielle Spannungsänderung

(Spannungsflankensteilheit)

∆V/∆t Voltage change per time interval Spannungsänderung pro Zeitintervall

E Activation energy for diffusion Aktivierungsenergie zur Diffusion

ESL Self-inductance Eigeninduktivität

ESR Equivalent series resistance Ersatz-Serienwiderstand

f Frequency Frequenz

f1Frequency limit for reducing permissible

AC voltage due to thermal limits

Grenzfrequenz für thermisch bedingte

Reduzierung der zulässigen

Wechselspannung

f2Frequency limit for reducing permissible

AC voltage due to current limit

Grenzfrequenz für strombedingte

Reduzierung der zulässigen

Wechselspannung

frResonant frequency Resonanzfrequenz

FDThermal acceleration factor for diffusion Therm. Beschleunigungsfaktor zur

Diffusion

FTDerating factor Deratingfaktor

i Current (peak) Stromspitze

ICCategory current (max. continuous

current)

Kategoriestrom (max. Dauerstrom)

B32632 ... B32634

Very high pulse (wound)

Page 26 of 29Please read Cautions and warnings and

Important notes at the end of this document.

Symbol English German

IRMS (Sinusoidal) alternating current,

root-mean-square value

(Sinusförmiger) Wechselstrom

izCapacitance drift Inkonstanz der Kapazität

k0Pulse characteristic Impulskennwert

LSSeries inductance Serieninduktivität

λFailure rate Ausfallrate

λ0Constant failure rate during useful

service life

Konstante Ausfallrate in der

Nutzungsphase

λtest Failure rate, determined by tests Experimentell ermittelte Ausfallrate

Pdiss Dissipated power Abgegebene Verlustleistung

Pgen Generated power Erzeugte Verlustleistung

Q Heat energy Wärmeenergie

ρDensity of water vapor in air Dichte von Wasserdampf in Luft

R Universal molar constant for gases Allg. Molarkonstante für Gas

R Ohmic resistance of discharge circuit Ohmscher Widerstand des

Entladekreises

RiInternal resistance Innenwiderstand

Rins Insulation resistance Isolationswiderstand

RPParallel resistance Parallelwiderstand

RSSeries resistance Serienwiderstand

S severity (humidity test) Schärfegrad (Feuchtetest)

t Time Zeit

T Temperature Temperatur

τTime constant Zeitkonstante

tan δDissipation factor Verlustfaktor

tan δDDielectric component of dissipation

factor

Dielektrischer Anteil des Verlustfaktors

tan δPParallel component of dissipation factor Parallelanteil des Verlfustfaktors

tan δSSeries component of dissipation factor Serienanteil des Verlustfaktors

TAAmbient temperature Umgebungstemperatur

Tmax Upper category temperature Obere Kategorietemperatur

Tmin Lower category temperature Untere Kategorietemperatur

tOL Operating life at operating temperature

and voltage

Betriebszeit bei Betriebstemperatur und

-spannung

Top Operating temperature Beriebstemperatur

TRRated temperature Nenntemperatur

Tref Reference temperature Referenztemperatur

tSL Reference service life Referenz-Lebensdauer

VAC AC voltage Wechselspannung

B32632 ... B32634

Very high pulse (wound)

Page 27 of 29Please read Cautions and warnings and

Important notes at the end of this document.

Symbol English German

VCCategory voltage Kategoriespannung

VC,RMS Category AC voltage (Sinusförmige)

Kategorie-Wechselspannung

VCD Corona-discharge onset voltage Teilentlade-Einsatzspannung

Vch Charging voltage Ladespannung

VDC DC voltage Gleichspannung

VFB Fly-back capacitor voltage Spannung (Flyback)

ViInput voltage Eingangsspannung

VoOutput voltage Ausgangssspannung

Vop Operating voltage Betriebsspannung

VpPeak pulse voltage Impuls-Spitzenspannung

Vpp Peak-to-peak voltage Impedance Spannungshub

VRRated voltage Nennspannung

RAmplitude of rated AC voltage Amplitude der Nenn-Wechselspannung

VRMS (Sinusoidal) alternating voltage,

root-mean-square value

(Sinusförmige) Wechselspannung

VSC S-correction voltage Spannung bei Anwendung "S-correction"

Vsn Snubber capacitor voltage Spannung bei Anwendung

"Beschaltung"

Z Impedance Scheinwiderstand

Lead spacing Rastermaß

B32632 ... B32634

Very high pulse (wound)

Page 28 of 29Please read Cautions and warnings and

Important notes at the end of this document.

The following applies to all products named in this publication:

1. Some parts of this publication contain statements about the suitability of our products for

certain areas of application. These statements are based on our knowledge of typical re-

quirements that are often placed on our products in the areas of application concerned. We

nevertheless expressly point out that such statements cannot be regarded as binding

statements about the suitability of our products for a particular customer application.

As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar

with them than the customers themselves. For these reasons, it is always ultimately incum-

bent on the customer to check and decide whether an EPCOS product with the properties de-

scribed in the product specification is suitable for use in a particular customer application.

2. We also point out that in individual cases, a malfunction of electronic components or

failure before the end of their usual service life cannot be completely ruled out in the

current state of the art, even if they are operated as specified. In customer applications

requiring a very high level of operational safety and especially in customer applications in

which the malfunction or failure of an electronic component could endanger human life or

health (e.g. in accident prevention or lifesaving systems), it must therefore be ensured by

means of suitable design of the customer application or other action taken by the customer

(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by

third parties in the event of malfunction or failure of an electronic component.

3. The warnings, cautions and product-specific notes must be observed.

4. In order to satisfy certain technical requirements, some of the products described in this

publication may contain substances subject to restrictions in certain jurisdictions (e.g.

because they are classed as hazardous). Useful information on this will be found in our Ma-

terial Data Sheets on the Internet (www.epcos.com/material). Should you have any more de-

tailed questions, please contact our sales offices.

5. We constantly strive to improve our products. Consequently, the products described in this

publication may change from time to time. The same is true of the corresponding product

specifications. Please check therefore to what extent product descriptions and specifications

contained in this publication are still applicable before or when you place an order. We also

reserve the right to discontinue production and delivery of products. Consequently, we

cannot guarantee that all products named in this publication will always be available. The

aforementioned does not apply in the case of individual agreements deviating from the fore-

going for customer-specific products.

6. Unless otherwise agreed in individual contracts, all orders are subject to the current ver-

sion of the "General Terms of Delivery for Products and Services in the Electrical In-

dustry" published by the German Electrical and Electronics Industry Association

(ZVEI).

7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSMP, CSSP, CTVS, DSSP,

MiniBlue, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, SIFERRIT,

SIFI, SIKOREL, SilverCap, SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse,

WindCap are trademarks registered or pending in Europe and in other countries. Further

information will be found on the Internet at www.epcos.com/trademarks.

Important notes

Page 29 of 29