410A
PHASE CONTROL THYRIST ORS Hockey Puk Version
ST230C..C SERIES
Bulletin I25162/B
Features
Center amplifying gate
Metal case with ceramic insulator
International standard case TO-200AB (A-PUK)
Typical Applications
DC motor controls
Controlled DC power supplies
AC controllers
IT(AV) 410 A
@ Ths 55 °C
IT(RMS) 780 A
@ Ths 25 °C
ITSM @ 50Hz 5700 A
@ 60H z 5970 A
I2t@
50Hz 163 KA2s
@ 60Hz 149 KA2s
VDRM/VRRM 400 to 1600 V
tqtypical 100 µs
TJ- 40 to 125 °C
Parameters ST230C..C Units
Major Ratings and Characteristics case style TO-200AB (A-PUK)
Next Data SheetIndex
Previous Datasheet
To Order
ST230C..C Series
di/dt Max. non-repetitive rate of rise Gate drive 20V, 20, tr 1µs
of turned-on current TJ = TJ max, anode voltage 80% VDRM
Gate current 1A, d i g/dt = 1A/µs
Vd = 0.67% VDRM, TJ = 25°C
ITM = 300A, TJ = TJ max, di/dt = 20A/µs, VR = 50V
dv/dt = 20V/µs, Gate 0V 100Ω, tp = 500µs
Parameter ST230C..C Units Conditions
Switching
1000 A/µs
tdTypical delay time 1 .0
tqTypical turn-off time 100
µs
ELECTRICAL SPECIFICATIONS
Voltage Ratings
Voltage V DRM/VRRM, max. repetitive VRSM , maximum non- IDRM/IRRM max.
Type number Code peak and off-state voltage repetitive peak voltage @ TJ = TJ max
VVmA
04 400 500
08 800 900
ST230C..C 12 1200 1300 30
14 1400 1500
16 1600 1700
IT(AV) Max. average on-state current 410 (165) A 180° conduction, half sine wave
@ Heatsink temperature 55 (85) °C double side (single side) cooled
IT(RMS) Max. RMS on-state current 780 DC @ 25°C heatsink temperature double side cooled
ITSM Max. peak, one-cycle 5700 t = 10ms No voltage
non-repetitive surge current 5970 A t = 8.3ms reapplied
4800 t = 10m s 100% VRRM
5000 t = 8.3ms reapplied Sinusoidal half wave,
I2t Maximum I2t for fusing 163 t = 10ms No voltage Initial TJ = TJ max.
148 t = 8.3ms reapplied
115 t = 10ms 100% VRRM
105 t = 8.3ms rea pplied
I2t Maximum I2t for fusing 1630 KA2s t = 0.1 to 10ms, no voltage reapplied
VT(TO)1Low level value of threshold
voltage
VT(TO)2High level value of threshold
voltage
rt1 Low level value of on-state
slope resistance
rt2 High level value of on-state
slope resistance
VTM Max. on-state voltage 1.69 V Ipk= 880A, TJ = T J max, tp = 10ms sine pulse
IHMaximum holding current 600
ILMax. (typical) latching current 1000 (300)
0.92 (16.7% x π x I T(AV) < I < π x IT(AV)), TJ = TJ max.
0.88 (16.7% x π x IT(AV) < I < π x IT(AV)), TJ = TJ max.
0.81 (I > π x IT(AV)),TJ = TJ max.
Parameter ST230C..C Units Conditions
0.98 (I > π x IT(AV)),TJ = T J max.
On-state Conduction
KA2s
V
m
mA TJ = 25 ° C , anode supply 12V resistive load
Next Data SheetIndex
Previous Datasheet
To Order
ST230C..C Series
dv/dt Maximum critical rate of rise of off-state voltage
IDRM Max. peak reverse and off-state
IRRM leakage current
Blocking
500 V/µsT
J
= TJ max. linear to 80% rated VDRM
Parameter ST230C..C Units Conditions
30 mA TJ = TJ m ax, rated V DRM/VRRM applied
PGM Maximum peak gate power 10.0 TJ = TJ max, t p 5ms
PG(AV) Maximum average gate power 2. 0 TJ = TJ max, f = 50Hz, d% = 50
IGM Max. peak positive gate current 3. 0 A TJ = TJ max, t p 5ms
+VGM Maximum peak positive
gate voltage
-VGM Maximum peak negative
gate voltage
TJ = - 40°C
mA TJ = 25°C
TJ = 125°C
TJ = - 40°C
VT
J
= 25°C
TJ = 125°C
IGD DC gate current not to trigger 10 mA
Parameter ST230C..C Units Conditions
20
5.0
Triggering
TYP. MAX.
180 -
90 150
40 -
2.9 -
1.8 3.0
1.2 -
VGD DC gate voltage not to trigger 0.25 V
Max. gate current/voltage not to
trigger is the max. value which
will not trigger any unit with rated
VDRM anode-to-cathode applied
TJ = TJ max
Max. required gate trigger/ cur-
rent/ voltage are the lowest value
which will trigger all units 12V
anode-to-cathode applied
VGT DC gate voltage required
to trigger
IGT DC gate current required
to trigger
W
VT
J
= TJ max, tp 5ms
TJMax. operating temperature range -40 to 125
Tstg Max. storage temperature range -40 to 150
RthJ-hs Max. thermal resistance, 0.17 DC operation single side cooled
junction to heatsink 0.08 DC operation double side cooled
RthC-hs Max. thermal resistance, 0.033 DC operation single side cooled
case to heatsink 0.017 DC operation double side cooled
F Mounting force, ± 10% 4900 N
(500) (Kg)
wt Approximate weight 50 g
Parameter ST230C..C Units Conditions
K/W
Thermal and Mechanical Specification
°C
Case style TO - 200AB (A-PUK) See Outline Table
K/W
To Order
Next Data SheetIndex
Previous Datasheet
ST230C..C Series
1- Thyristor
2- Essential part number
3-0 = Converter grade
4-C = Ceramic Puk
5- Voltage code: Code x 100 = VRRM (See Voltage Rating Table)
6- C = Puk Case TO-200AB (A-PUK)
7- 0 = Eyelet terminals (Gate and Auxiliary Cathode Unsoldered Leads)
1 = Fast-on terminals (Gate and Auxiliary Cathode Unsoldered Leads)
2 = Eyelet terminals (Gate and Auxiliary Cathode Soldered Leads)
3 = Fast-on terminals (Gate and Auxiliary Cathode Soldered Leads)
8- Critical dv/dt: None = 500V/µsec (Standard selection)
L = 1000V/µsec (Special selection)
Ordering Information Table
RthJ-hs Conduction
(The following table shows the increment of thermal resistence RthJ-hs when devices operate at different conduction angles than DC)
Device Code
5
3 4
ST 23 0 C 16 C 1
7
68
12
Single Side Double Side Single Side Double Side
180° 0.015 0.017 0.011 0.011 TJ = TJ max.
12 0.018 0.019 0.019 0.019
90° 0.024 0.024 0.026 0.026 K/W
60° 0.035 0.035 0.036 0.037
30° 0.060 0.060 0.060 0.061
Sinusoidal conduction Rectangular conduction
Conduction angle Units Conditions
To Order
Next Data SheetIndex
Previous Datasheet
ST230C..C Series
Outline Table
Case Style TO-200AB (A-PUK)
All dimensions in millimeters (inches)
Fig. 1 - Current Ratings Characteristics Fig. 2 - Current Ratings Characteristics
40
50
60
70
80
90
100
110
120
130
0 40 80 120 160 200 240 280 320
30° 60° 90° 12 18
Average On-stat e Curre nt ( A)
Conduction A ngl e
Maximum Allow ab le Heatsink Tem perat ure ( °C )
ST230C..C Series
(Si ngle Side Cooled)
R (DC) = 0.17 K/W
thJ-hs
20
30
40
50
60
70
80
90
100
110
120
130
0 100 200 300 400 500
DC
30° 60°90°12180°
Aver age On- state Cu r rent (A)
Conduction Per i od
Maxim u m A llowable Heat sin k Temperature ( °C)
ST2 30C..C Series
(Singl e Side Cool ed)
R (DC) = 0 .17 K/W
thJ-hs
DIA. MAX.
4.75 (0.19)
28 (1.10)
6.5 (0.26)
19 (0.75)
0.3 (0.01) MIN.
0.3 (0.01) MIN.
13.7 / 14.4
(0.54 / 0.57)
25°± 5°
GATE TERM. FOR
1.47 (0.06) DIA.
PIN RECEPTACLE
ANODE TO GATE
CREEPAGE DISTANCE: 7.62 (0.30) MIN.
STRIKE DISTANCE: 7.12 (0.28) MIN.
19 (0.75)
DIA. MAX.
38 (1.50) DIA MAX.
2 HOLES 3.56 (0.14) x
1.83 (0.07) MIN. DEEP
42 (1.65) MAX.
To Order
Next Data SheetIndex
Previous Datasheet
ST230C..C Series
2000
2500
3000
3500
4000
4500
5000
5500
110100
Number Of Equal Amplitude Half Cycle Current Pulses (N)
Peak Hal f Sine W ave On- state Cur rent (A)
Initial T = 125°C
@ 60 Hz 0.00 83 s
@ 50 Hz 0.01 00 s
J
ST230 C..C Ser ies
At Any Rate d Load Condition And With
Rated V Applied Fo llow ing Surge.
RRM
2000
2500
3000
3500
4000
4500
5000
5500
6000
6500
0.01 0.1 1
Pulse Train D uration (s)
Versus Pulse Train Dur ation. Control
Of Conduction May Not Be Maintained.
Peak Hal f Si ne W ave On-state Cur rent (A)
Initial T = 12 5°C
No Voltage Reapplied
Rate d V Re applie d
RRM
J
ST230C..C Serie s
Maximum N on Repetiti ve Surge Curr ent
20
30
40
50
60
70
80
90
100
110
120
130
0 100 200 300 400 500 600
30° 60° 90° 120° 180°
A v erage On -state C u rre nt ( A )
Con du cti on Angl e
Maxim um Allow able Heatsin k Temperatu re ( °C )
ST23 0C..C Series
(Double Side Cooled)
R (DC) = 0 .0 8 K/W
thJ-hs
Fig. 7 - Maximum Non-Repetitive Surge Current
Single and Double Side Cooled Fig. 8 - Maximum Non-Repetitive Surge Current
Single and Double Side Cooled
20
30
40
50
60
70
80
90
100
110
120
130
0 100 200 300 400 500 600 700 800
DC
30° 60° 90° 120° 180°
A v e rage On -state Curre nt ( A)
Conduction Per i od
Maxim um Allowable Heatsin k Temperat ure (°C)
ST2 30C..C Series
(Double Side Cooled)
R (D C) = 0 .08 K/W
thJ-hs
0
100
200
300
400
500
600
700
800
900
1000
1100
0 100 200 300 400 500 600
18
12
90°
60°
30° RMS Limit
Con ducti on An gl e
Maxi m um A ve r age On- state Power Loss (W)
Average On- state Curr ent (A )
ST230C..C Series
T = 1 25°C
J
0
200
400
600
800
1000
1200
1400
0 100 200 300 400 500 600 700 800 900
DC
180°
120°
90°
60°
30°
RMS Lim it
Conduction Period
M a x imum A v e rage On -state Power Loss (W)
Aver age On- state Current (A)
ST230C ..C Serie s
T = 125°C
J
Fig. 3 - Current Ratings Characteristics Fig. 4 - Current Ratings Characteristics
Fig. 5- On-state Power Loss Characteristics Fig. 6- On-state Power Loss Characteristics
To Order
Next Data SheetIndex
Previous Datasheet
ST230C..C Series
Fig. 10 - Thermal Impedance ZthJ-hs Characteristics
Fig. 9 - On-state Voltage Drop Characteristics
Fig. 11 - Gate Characteristics
100
1000
10000
0.511.522.533.544.55
T = 25°C
J
Instantane ous O n -state C u rre n t (A )
Instan tan eous O n-st ate Volt age (V )
T = 125°C
J
ST2 30C..C Series
0.001
0.01
0.1
1
0.001 0.01 0.1 1 10
Square Wave Pulse Duration (s)
thJ-hs
ST23 0C.. C Ser ies
Steady State Valu e
R = 0.17 K/W
(Single Side Cooled)
R = 0.08 K/W
(Double Side Cooled)
(D C Op erat io n )
thJ-hs
thJ-hs
Transient Thermal Impedance Z (K/W)
0.1
1
10
100
0.001 0.01 0.1 1 10 100
VGD IGD
(b)
(a)
Tj=25 °C
Tj=125 °C
Tj =- 40 °C
(1) (2) (3)
Instantaneous Gate Cu r rent (A)
I nstan taneous Gate Voltage (V )
a) Re comm en ded load line for
b) Re com me nded l o ad l i n e f or
<=30% rated di/dt : 1 0 V, 1 0 ohms
Frequency Lim i ted by PG(AV )
rated di/dt : 2 0V, 1 0 ohms; tr< =1 µs
tr<=1 µs
(1) PG M = 1 0W, tp = 4 ms
(2) PG M = 2 0W, tp = 2 ms
(3) PG M = 4 0W, tp = 1 ms
(4) PGM = 6 0W, tp = 0 .66ms
Rectangul ar gate pulse
Device: ST23 0C..C Series
(4)
To Order
Next Data SheetIndex
Previous Datasheet