Freescale Semiconductor, Inc.
User’s Guide
© Freescale Semiconductor, Inc., 2015. All rights reserved.
Document Number: KTPT2000FRDM6CUG
Rev. 2.0, 6/2015
KITPT2000FRDM6C Evaluation Board
Figure 1. KITPT2000FRDM6C Evaluation Board
KTPT2000FRDM6CUG Rev. 2.0
2Freescale Semiconductor, Inc.
Contents
1 Important Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1 Kit Contents/Packing List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2 Jump Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.3 Required Equipment and Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.4 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3 Understanding the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.1 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.2 FRDM-KL25Z Freedom Development Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.3 Connecting the FRDM-KL25Z Freedom Development Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4 Getting to Know the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.1 Board Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.2 Board Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.3 FRDM-KL25Z Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.4 Board Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.5 DC/DC Optional Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.6 LED Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.7 Test Point Signal Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.8 Pin Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.9 MC33PT2000 EVB Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.10 Freedom Board FRDM - KL25Z Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5 Installing the Software and Setting Up the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.1 Installing SPIGen Freeware On Your Computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.2 Configuring the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.3 Step-by-step Instructions for Setting Up the Hardware Using SPIGen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.4 Running an Example Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.5 Running the Example Batch Files. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.6 Typical Peak and Hold Scope Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7 Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
8 Silkscreen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8.1 Silkscreen Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
9 Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
10 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
10.1 Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
10.2 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
11 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Important Notice
KTPT2000FRDM6CUG Rev. 2.0
Freescale Semiconductor, Inc. 3
1 Important Notice
Freescale provides the enclosed product(s) under the following conditions:
This evaluation kit is intended for use of ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY.
It is provided as a sample IC pre-soldered to a printed circuit board to make it easier to access inputs, outputs, and
supply terminals. This EVB may be used with any development system or other source of I/O signals by simply
connecting it to the host MCU or computer board via off-the-shelf cables. This EVB is not a Reference Design and
is not intended to represent a final design recommendation for any particular application. Final device in an
application will be heavily dependent on proper printed circuit board layout and heat sinking design as well as
attention to supply filtering, transient suppression, and I/O signal quality.
The goods provided may not be complete in terms of required design, marketing, and or manufacturing related
protective considerations, including product safety measures typically found in the end product incorporating the
goods. Due to the open construction of the product, it is the user's responsibility to take any and all appropriate
precautions with regard to electrostatic discharge. In order to minimize risks associated with the customers
applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or
procedural hazards. For any safety concerns, contact Freescale sales and technical support services.
Should this evaluation kit not meet the specifications indicated in the kit, it may be returned within 30 days from the
date of delivery and will be replaced by a new kit.
Freescale reserves the right to make changes without further notice to any products herein. Freescale makes no
warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters
can and do vary in different applications and actual performance may vary over time. All operating parameters,
including “Typical”, must be validated for each customer application by customer's technical experts.
Freescale does not convey any license under its patent rights nor the rights of others. Freescale products are not
designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or
other applications intended to support or sustain life, or for any other application in which the failure of the Freescale
product could create a situation where personal injury or death may occur.
Should the buyer purchase or use Freescale products for any such unintended or unauthorized application, the
buyer shall indemnify and hold Freescale and its officers, employees, subsidiaries, affiliates, and distributors
harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or
indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that Freescale was negligent regarding the design or manufacture of the part. Freescale™ and the
Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property
of their respective owners.
© Freescale Semiconductor, Inc. 2015.
Getting Started
KTPT2000FRDM6CUG Rev. 2.0
4Freescale Semiconductor, Inc.
2 Getting Started
2.1 Kit Contents/Packing List
The KITPT2000FRDM6C contents include:
• Assembled and tested evaluation board in an anti-static bag
• Quick Start Guide, Analog Tools
• Warranty card
• USB cable to connect KL25Z to computer
2.2 Jump Start
Freescale’s analog product development boards help to easily evaluate Freescale products. These tools support analog mixed signal and
power solutions including monolithic ICs using proven high-volume SMARTMOS mixed signal technology, and system-in-package devices
utilizing power, SMARTMOS and MCU dies. Freescale products enable longer battery life, smaller form factor, component count reduction,
ease of design, lower system cost and improved performance in powering state of the art systems.
•Go to www.freescale.com/analogtools
•Locate the kit
• Review the Tool Summary Page
• Look for
• Download documents, software, and other information
Once the files are downloaded, review the user guide in the bundle. The user guide includes setup instructions, BOM and schematics.
Jump start bundles are available on each tool summary page with the most relevant and current information. The information includes
everything needed for design.
2.3 Required Equipment and Software
To use this kit, you need:
•12 V power supply with current limit set initially to 4.0 A
• Oscilloscope (four-channel preferably) with current probe(s) (10 MHz bandwidth)
• SPIGen 7.0 or greater www.freescale.com/analogtools
2.4 System Requirements
The kit requires the following to function properly with the software:
• USB-enabled PC with Windows® XP or higher
Understanding the System
KTPT2000FRDM6CUG Rev. 2.0
Freescale Semiconductor, Inc. 5
3 Understanding the System
The KITPT2000FRDM6C uses the Freedom board KL25Z to communicate with the MC33PT2000 through the SPI to setup registers and
flash CRAM and DRAM. The KL25Z also controls the start and end of injection using the STARTx pins. This particular application drives
three injectors, two fuel pumps, and an external DC/DC.
3.1 Block Diagram
The high level system block diagram (Figure 2) outlines the way the Freescale standard products are used to implement this particular
application of six cylinders (INJ1, INJ2, INJ3, INJ4, INJ5 and INJ6), a fuel pump and a DCDC. Communication between the KL25Z and
MC33PT2000 is done by SPI, control and reporting is done through I/Os.
Figure 2. Block Diagram
Understanding the System
KTPT2000FRDM6CUG Rev. 2.0
6Freescale Semiconductor, Inc.
3.1.1 Device Features
This evaluation board features the following Freescale products:
3.2 FRDM-KL25Z Freedom Development Platform
The Freescale Freedom development platform is a set of software and hardware tools for evaluation and development. It is ideal for rapid
prototyping of microcontroller-based applications. The Freescale Freedom KL25Z hardware, FRDM-KL25Z, is a simple, yet sophisticated
design featuring a Kinetis L Series microcontroller, the industry's first microcontroller built on the ARM® Cortex™-M0+ core.
Figure 3. FRDM-KL25Z
Table 1. MC33PT2000 Device Features
Device Description Features
MC33PT2000 Programmable Solenoid Controller,
7 high-sides and 8 low-sides
• Battery voltage range, 5.5 V < VBATT < 32 V (1)
• Pre-drive operating voltage up to 72 V
• High-side/low-side pre-drive PWM capability up to 100 kHz
• All pre-drivers with four selectable slew rates
• Eight selectable, pre-defined VDS monitoring thresholds
• Encryption for microcode protection
• Integrated 1.0 MHz backup clock
Notes
1. If VSUPP > 16 V, it is highly recommended to disable the internal VCCP regulator and externally supply VCCP.
Understanding the System
KTPT2000FRDM6CUG Rev. 2.0
Freescale Semiconductor, Inc. 7
3.3 Connecting the FRDM-KL25Z Freedom Development Platform
KITPT2000FRDM6C includes a KL25Z already flashed to use as a SPI dongle to control the MC33PT2000. A USB cable from a USB host
to the KL25Z mini-B USB connector and SPIGEN (7.xx and above) are all that are needed to use the kit.
The following chapters, Section 3.3.1, Installing the Drivers (Optional), page 7 through Section 3.3.4, Using the MSD Flash
Programmer (Optional), page 7 are optional and only required if a software update is needed, or if the user wants to reprogram the KL25Z
to develop their own application.
3.3.1 Installing the Drivers (Optional)
To flash the Freedom board using drag and drop from Windows Explorer, USB Drivers, and OpenSDA Firmware (MSD & Debug) from
P&E Micro www.pemicro.com/opensda must be loaded on the board.
3.3.2 Enter OpenSDA Bootloader Mode (Optional)
1. Unplug the USB cable if attached.
2. Press and hold the Reset button (SW1).
3. Plug in a USB cable between a USB host and the OpenSDA USB connector (labeled SDAII).
4. Release the Reset button.
A removable drive is visible in the host file system with a volume label of BOOTLOADER. It is now in OpenSDA Bootloader mode.
3.3.3 Load an OpenSDA Application (Optional)
1. Locate the OpenSDA Applications folder from the downloaded zip file.
2. Copy and paste, or drag and drop the MSD Flash Programmer Application (MSD-FRDM-KL25Z_vXYZ_Pemicro.SDA) to the
BOOTLOADER drive (Make sure to unzip the file before doing the paste or drop).
3. Unplug the USB cable and plug it into the SDA USB Connector. The new OpenSDA Application is now running and a
FRDM-KL25Z drive visible in the host file system.
3.3.4 Using the MSD Flash Programmer (Optional)
1. Locate SPIGEN UsbSpiDongleKL25Z_XXX.srec image folder in SPIGEN folder (C:\Program Files (x86)\SPIGen\SPI Dongle
Firmware).
2. Copy and paste, or drag and drop the .srec file to the FRDM-KL25Z drive.
3. Unplug the USB cable from the open SDA USB Connector and plug it into the USB_KL25Z.
Getting to Know the Hardware
KTPT2000FRDM6CUG Rev. 2.0
8Freescale Semiconductor, Inc.
4 Getting to Know the Hardware
4.1 Board Overview
The KITPT2000FRDM6C is an easy-to-use circuit board allowing the user to exercise all the functions of the MC33PT2000 smart
pre-driver circuit. A PC communicates to the evaluation board (EVB) through a Freedom board (FRDM-KL25Z) connected to the PC’s
USB port. The Freescale SPIGen program (version 7.0 and above) provides the user interface to the MC33PT2000 SPI port and allows
the user to program the Code RAM and Data Registers, send commands to the IC, and receive status from the IC.
4.2 Board Features
The board features are as follows:
• MC33PT2000 direct injection pre-driver integrated circuit
• USB-to-SPI dongle interface using the FRDM-KL25Z
• External MOSFETs
• Power-conditioning circuitry
•+5.0 V regulator supplies all +5.0 V power required by the MC33PT2000 EVB
•+12 V VSUPP provides the power to the MC33PT2000 and the loads
4.3 FRDM-KL25Z Features
The FRDM-KL25Z board features are as follows:
• MKL25Z128VLK4 MCU - 48 MHz, 128 KB Flash, 16 KB SRAM, USB OTG (FS), 80LQFP
• Capacitive touch slider, MMA8451Q accelerometer, Tri-color LED
• Flexible power supply options - USB, coin cell battery, external source
• Easy access to MCU I/O
• Battery-ready, power-measurement access points
• Form factor compatible with Arduino™ R3 pin layout
• New, OpenSDA debug interface
• Mass storage device flash programming interface (default) - no tool installation required to evaluate demonstration applications
• P&E Debug interface provides run-control debugging and compatibility with IDE tools
• CMSIS-DAP interface: new ARM standard for embedded debug interface
Additional reference documents are available on www.freescale.com/FRDM-KL25Z
Getting to Know the Hardware
KTPT2000FRDM6CUG Rev. 2.0
Freescale Semiconductor, Inc. 9
4.4 Board Description
The analog part consists of the MC33PT2000 chip controlling external drivers. The digital part consists of the KL25Z controlling the
MC33PT2000 by the SPI and I/Os.
Figure 4. Board Description
Table 2. Board Description
Name Description
KL25Z Microcontroller used to communicate with the computer by using a USB and to the MC33PT2000 using
SPI
DCDC DCDC converter to generate BOOST voltage
BANK1 Bank1: 2 high-side + 2 low-side to control injectors 1 and 2
BANK2 Bank2: 2 high-side + 2 low-side to control injectors 3 and 4
BANK3 Bank3: 2 high-side + 2 low-side to control injectors 5 and 6
Fuel Pump Fuel Pump: 1 high-side + 1 low side to control low pressure fuel pump
MC33PT2000 Programmable solenoid controller
Pi Filter Pi Filter circuits to remove unwanted or undesired frequencies
Getting to Know the Hardware
KTPT2000FRDM6CUG Rev. 2.0
10 Freescale Semiconductor, Inc.
4.5 DC/DC Optional Configuration
The KITPT2000FRDM6C uses a DC/DC in hysteretic mode by default. However, it is possible to configure it as resonant mode. In this
case, the C_RES capacitor has to be populated. For more detail on the hysteretic and resonant mode, refer to the PT2000 datasheet. The
microcode example on the web controls the DC/DC in hysteretic mode.
Figure 5. DC/DC Different Configuration
4.6 LED Display
Five LEDs are provided as visual output devices for the KITPT2000FRDM6C evaluation board. The LED devices are:
1. FLAG0 LED - Indicates the digital FLAG 0 output is a logic 1
2. FLAG1 LED - Indicates the digital FLAG 1 output is a logic 1
3. FLAG2 LED - Indicates the digital FLAG 2 output is a logic 1
4. FLAG3 LED - Indicates the digital FLAG 3 output is a logic 1
5. +5.0 V LED - Indicates the +5.0 volt regulator is running.
6. USB_PWR LED - Indicates the KL25Z FRDM is connected properly and is attached to an active USB port on a PC.
Table 3. DC/DC Mode Versus Component Placement
DC/DC mode Q9 C_GSHS7 R_CHSb7 C_RES C_BHS7
Hysteretic (default) Diode Shorted Do not place Do not place Do not place
Resonant Diode Shorted Do not place 10 nF Do not place
FW with MOSFET MOSFET (BUK9230) 1.0 F 1.0 Do not place 1.0 F
Getting to Know the Hardware
KTPT2000FRDM6CUG Rev. 2.0
Freescale Semiconductor, Inc. 11
4.7 Test Point Signal Definitions
The KITPT2000FRDM6C has nine logic level input signals used to control certain outputs or functions inside the circuit. These are:
1. DRVEN - Controls the state of the all the pre-driver outputs
2. IRQ - Interrupt pin connected to KL25Z
3. DBG - I/O that can be configured to disable internal VCCP
4. RESETB - When the RESETB line is held low, the MC33PT2000 is reset
5. START1 - Provides start signal for Injector 1
6. START2 - Provides start signal for Injector 2
7. START3 - Provides start signal for Injector 3
8. START4 - Provides start signal for Injector 4.
9. START5 - Provides start signal for Injector 5
10. START6 - Provides start signal for Injector 6
11. START7 - Provides start signal for fuel pump
12. FLAG 0 to 4 - Flag pin used as output
13. CLK - Provides 1.0 MHz CLK to the MC33PT2000
14. CSB - SPI chip select
15. MOSI - SPI Master Out Slave In
16. MISO - SPI Master In Slave Out
17. SCLK - SPI CLK up to 10 MHz
18. G_LSx - Gate low ide
19. G_HSx - Gate high-side
20. VCCP - VCCP voltage
21. VCCIO - I/O voltage set to 3.3 V by default (JVCCIO)
22. 5.0 V - VCC5 voltage
23. VBOOST - VBOOST voltage
24. VBAT - Battery voltage
25. OA1 to 3 - OAx test point for current recopy or I/Os
26. GND - Ground test points
4.8 Pin Jumpers
There are two jumper headers on the KITPT2000FRDM6C.
1. VCCIO_SEL - This is a header to supply VCCIO from the +3.3 V regulator on the KL25Z (3.3V logic). If not connected, no
voltage goes through the I/Os
2. CLK_SEL - This is a header to select the KL25Z Oscillator which is set to 1 MHz. If not connected, the internal 1.0 MHz
backup CLK is used.
Getting to Know the Hardware
KTPT2000FRDM6CUG Rev. 2.0
12 Freescale Semiconductor, Inc.
4.9 MC33PT2000 EVB Connectors
4.9.1 Input Connector
There is one input connector used to connect the KITPT2000FRDM6C to +12 V.
1. (VSUPP) +12 VOLT POWER SUPPLY INPUT -
Screw Terminal 1 (+) +12 V
Screw Terminal 2 (-) GND
4.9.2 Output Connectors
There are seven output connectors that provide six injectors and a fuel pump:
1. (INJ1) INJECTOR OUTPUT 1 -
Screw Terminal 1 - High-side drive
Screw Terminal 2 - Low-side drive
2. (INJ2) INJECTOR OUTPUT 2 -
Screw Terminal 1 - High-side drive
Screw Terminal 2 - Low-side drive
3. (INJ3) INJECTOR OUTPUT 3 -
Screw Terminal 1 - High-side drive
Screw Terminal 2 - Low-side drive
4. (INJ4) INJECTOR OUTPUT 4-
Screw Terminal 1 - High-side drive
Screw Terminal 2 - Low-side drive
5. (INJ5) INJECTOR OUTPUT 5-
Screw Terminal 1 - High-side drive
Screw Terminal 2 - Low-side drive
6. (INJ6) INJECTOR OUTPUT 6-
Screw Terminal 1 - High-side drive
Screw Terminal 2 - Low-side drive
7. (FP) FUEL PUMP OUTPUT -
Screw Terminal 1 - High-side drive
Screw Terminal 2 - Low-side drive
Getting to Know the Hardware
KTPT2000FRDM6CUG Rev. 2.0
Freescale Semiconductor, Inc. 13
4.10 Freedom Board FRDM - KL25Z Connectors
The KL25Z board plugs into the four male connectors J7 - J10. It is attached using the four female connectors included in the kit.These
four connectors should be soldered directly on the KL25Z. Refer to Figure 3 for connector orientation.
Table 4. EVB J8 Pinout (Connects to J1 on LK25Z)
PIn SPIGen Signal Pin SPIGen Signal
J8 01 IRQ J8 02
J8 03 DBG J8 04 START8
J8 05 CLK J8 06 FLAG0
J8 07 FLAG1 J8 08
J8 09 FLAG2 J8 10
J8 11 FLAG3 J8 12
J8 13 J8 14
J8 15 J8 16
Table 5. EVB J7 Pinout (Connects to J2 on KL25Z)
PIn SPIGen Signal Pin SPIGen Signal
J7 01 DRVEN J7 02
J7 03 RESETB J7 04
J7 05 START1 J7 06 CSB
J7 07 START2 J7 08 MOSI
J7 09 START3 J7 10 MISO
J7 11 START4 J7 12 SCLK
J7 13 START5 J7 14
J7 15 J7 16
J7 17 J7 18
J7 19 START6 J7 20 START7
Table 6. EVB J9 Pinout (Connects to J9 on KL25Z)
PIn SPIGen Signal Pin SPIGen Signal
J9 01 J9 02
J9 03 J9 04 3.3 V
J9 05 J9 06
J9 07 J9 08 3.3 V
J9 09 J9 10 USB PWR
J9 11 J9 12 GND
J9 13 J9 14 GND
J9 15 J9 16
Getting to Know the Hardware
KTPT2000FRDM6CUG Rev. 2.0
14 Freescale Semiconductor, Inc.
Table 7. EVB J10 Pinout (Connects to J10 on KL25Z)
PIn SPIGen Signal Pin SPIGen Signal
J10 01 OA1 J10 02
J10 03 OA2 J10 04
J10 05 OA3 J10 06
J10 07 J10 08
J10 09 J10 10
J10 11 J10 12
Installing the Software and Setting Up the Hardware
KTPT2000FRDM6CUG Rev. 2.0
Freescale Semiconductor, Inc. 15
5 Installing the Software and Setting Up the Hardware
5.1 Installing SPIGen Freeware On Your Computer
The latest version of SPIGen is designed to run on Windows 8, Windows 7, Vista, or XP-based operating systems. To install the software,
go to www.freescale.com/analogtools and select your kit. Click on that link to open the corresponding Tool Summary Page. Look for “Jump
Start Your Design”. Download to your computer desktop the SPIGen software, as well as the associated configuration file.
Run the install program from the desktop. The Installation Wizard conducts the rest of the process.
To use SPIGen, go to the Windows Start menu, then Programs, then SPIGen, and click on the SPIGen icon. The SPIGen Graphic User
Interface (GUI) appears. Go to the file menu in the upper left hand corner of the GUI, and select “Open”. In the file selection window that
appears, set the “Files of type:” drop-down menu to “SPIGen Files (*.spi)”. (As an exceptional case, the file name may have a .txt
extension, in which case, set the menu to “All Files (*.*)”.) Next, browse for the configuration file saved on the desktop earlier and select
it. Click “Open”, and SPIGen creates a specially configured SPI command generator for your evaluation board.
The GUI is shown in Figure 6. The text at the top is the name of the configuration file loaded. The left side panel displays folders grouping
user interfaces. The interfaces in the pre-installed MC33PT2000 folder pertain specifically to the board under discussion. The process of
loading the configuration file has assigned a list of “Extra Pins” as well as a list of “Quick Commands”, all of which are board-specific.
Figure 6. SPIGen GUI
Installing the Software and Setting Up the Hardware
KTPT2000FRDM6CUG Rev. 2.0
16 Freescale Semiconductor, Inc.
5.2 Configuring the Hardware
Figure 7. KITPT2000FRDM6C Board Setup
5.3 Step-by-step Instructions for Setting Up the Hardware Using SPIGen
The following connections and setup must be performed to use the examples included in the software bundle:
1. Make sure SPIGen 7.0 (or higher) is installed on the PC and it can communicate with the Freedom board KL25Z, as described
in the kit’s documentation. (See Section 5.1, Installing SPIGen Freeware On Your Computer, page 15).
2. Connect the KL25Z to the PC using the USB KL25Z port (left side of SW1). The USB_PWR LED on the KITPT2000FRDM6C
should be illuminated.
3. Attach the +12 VDC supply (do not turn on power yet) to the VSUPP input connector on the MC33PT2000 EVB, making sure
to observe the GND and +12 V terminals. The current capability of the +12 V supply should exceed the maximum total
current the number of simultaneous ON loads requires.
4. Attach loads (Injectors) to the INJ1, INJ2, INJ3, INJ4, INJ5 and INJ6 output terminals as desired.
5. Turn on the +12 V supply. Verify all is working correctly by observing the +5.0 V LED, which should be illuminated.
12.0V 2A
Mini USB
USB
Installing the Software and Setting Up the Hardware
KTPT2000FRDM6CUG Rev. 2.0
Freescale Semiconductor, Inc. 17
5.4 Running an Example Program
1. Launch the SPIGen program.
2. When the KL25Z is properly connected to the computer, the LED on the KL25Z turns blue while the SPIGen is running.
3. Load the config file, by clicking on "File" then "Open" and brows to the KITPT2000SW.spi file located inside the "Injector
Demo Files" directory.
4. Go to the "Micro code" page under "MC33PT2000".
5. Set the RESETB pin high.
6. Click on “Load Filenames”.
7. Open the SPIGenMC33PT2000Files.txt included in the project example. All cells should be filed with the right path (Code
Ramx, Data Ramx, Channelx, Main, IO, Diagnostics Configuration Registers.
8. Click on the “Download All” button to download all micro-code (CRAM), data ram, and register values into the PT2000 by the
SPI.
9. Click the "Enable Flash on CH1 CH2 and CH3" button to run the code. At this point both channels should be operational.
10. Set the DRVEN high.
11. Set the Start Pulse Width (ms) duration.
5.5 Running the Example Batch Files
1. Go to the “Batch commands” page and select the batch file desired to run. There are seven choices. “Start1” through “Start7”
pulse only one injector (1 to 7). The “Start1-7” batch command pulses all three injectors in sequence.
2. Click on the “Send Continuously” button.
3. Observe the seven loads attached to the KITPT2000FRDM6C are turning on and off in succession.
There are other demo batch examples which can be run and examined to learn how to use the KITPT2000FRDM6C.
Installing the Software and Setting Up the Hardware
KTPT2000FRDM6CUG Rev. 2.0
18 Freescale Semiconductor, Inc.
5.6 Typical Peak and Hold Scope Image
A scope image example is shown with an injector connected to INJ1. The expected behavior is when the Start1 pin rise injection goes into
Boost phase until the boost current is reached. It jumps to peak phase for 10 s, then bypass phase for 10 s, and then hold phase until
the start pin goes low.
Figure 8. Peak and Hold Scope Image
Troubleshooting
KTPT2000FRDM6CUG Rev. 2.0
Freescale Semiconductor, Inc. 19
6 Troubleshooting
Table 8. Troubleshooting
Problem Possible Solution
Code download fails (all files) Make sure the RESETB signal on the “Single Command” page is set to High
Download fails after “Main Con-
figuration Register”
Watchdog timeout is set too low. Using the IDE, update the spi_config register in the main config reg so the watchdog
value is set to the maximum value (bits 0-4 are set)
Code downloaded successfully,
but outputs are not toggling, and
the VBOOST voltage is not correct
Make sure the DRVEN signal on the “Single Command” or “Microcode”page is set to High
OR
After clicking on Download All, make sure to click on Enable Flash on CH1 and CH2
OR
Make sure that power supply current limitation is sufficiently high (~4 A)
SPIGen error: “The USB to SPI
Device was not found”
Make sure to use at least SPIGEN Rev 7.0. The KL25Z must be connected to the computer using the USB and con-
nected to the KL25Z_USB.
Schematics
KTPT2000FRDM6CUG Rev. 2.0
20 Freescale Semiconductor, Inc.
7 Schematics
Figure 9. KITPT2000FRDM6C Evaluation Board Schematic Part 1
DC-DC BLOCK
PI Filter
SH1 needs to be
placed close to
R_VSENSE6
VBAT Input Protection
5V Regulator
FRDM-KL25Z
FLAG LED
Test Points
Supplies
VCCIO_SELECT
CLK_SELECT
CLK
D_LS8
G_LS8
VSENSEP6
VSENSEN6
VPWR
GND
VPWR
VCC5
VSUPP
GND
IRQb
DBG
FLAG1
FLAG2
FLAG3
FLAG4
START8
CSB
MOSI
MISO
SCLK
START7
DRVEN
RESETb
START1
START2
START3
START4
START5
START6
OA1
OA2
OA3
GND
GND
GND
FLAG0
VCCIO
USB_PWR
3V3
3V3
COM
COM
COM
COM
COM
OA2
OA3
OA1
G_HS1
B_HS1
S_HS1
G_HS2
B_HS2
S_HS2
G_HS5
B_HS5
S_HS5
G_HS6
B_HS6
S_HS6
D_LS1
G_LS1
D_LS5
G_LS5
VSENSEP1
VSENSEN1
OA_1
VSENSEP2
VSENSEN2
VSENSEP5
VSENSEN5
S_HS3
B_HS3
G_HS3
S_HS4
B_HS4
G_HS4
S_HS7
B_HS7
G_HS7
D_LS3
G_LS3
D_LS7
G_LS7
OA_2
OA_3
VSENSEP6
VSENSEN6
FLAG0
FLAG1
FLAG2
FLAG3
DRVEN
CSb
SCLK
MOSI
MISO
RESETb
CLK
START1
START2
START3
START4
START5
START6
START7
VCC5VCC2P5
FLAG4
START8
IRQb
DBG
VBOOST
3V3
VCCIO
D_LS2
G_LS2
D_LS6
G_LS6
D_LS4
G_LS4
VCCP
VSENSEP3
VSENSEN3
D_LS8
G_LS8
INT_CLK
INT_CLK
FLAG0
FLAG2
FLAG1
FLAG3
USB_PWR
CLK
VBAT +5V
+5V
+5V
VCCP
VBAT
VBOOST
VBAT VPWR
VPWR
VBOOST
B_HS1
G_HS1
S_HS1
G_HS2
B_HS2
S_HS2
D_LS1
G_LS1
VSENSEP1
VSENSEN1
B_HS5
G_HS5
S_HS5
B_HS6
G_HS6
S_HS6
D_LS5
G_LS5
B_HS3
G_HS3
S_HS3
B_HS4
G_HS4
S_HS4
D_LS3
G_LS3
B_HS7
G_HS7
S_HS7
D_LS7
G_LS7
VSENSEP2
VSENSEN2
VSENSEP5
VSENSEN5
D_LS2
G_LS2
D_LS6
G_LS6
D_LS4
G_LS4
VSENSEP3
VSENSEN3
C24
330PF
U1
MC33PT2000
DRVEN
1
RESET
2
FLAG_0/EXTFW1
10
FLAG_1/EXTFW2
11
FLAG_2/EXTFW3
12
FLAG_3/EXTFW4
13
CS
14
MOSI
15 MISO
16
SCLK
17
VCCIO 18
DBG/FLAG_15
19
DGND
20
VCC2P5 21
VCC5 22
AGND
23
VSENSEN4/START8/FLAG_12 24
VSENSEP4/FLAG_4 25
VSENSEN1 26
VSENSEP1 27
VSENSEN2 28
VSENSEP2 29
VSENSEN3 30
VSENSEP3 31
VSENSEN5 _DC 32
VSENSEP5 _DC 33
VSENSEN6 _DC 34
VSENSEP6 _DC 35
OA_1 36
OA_2/FLAG_14 37
OA_3/D_HS1_7 38
D_LS8 _DC 39
D_LS7 _DC 40
D_LS6 41
D_LS5 42
D_LS4 43
D_LS3 44
D_LS2 45
D_LS1 46
VBATT
47
VCCP 48
G_LS8 _DC 49
G_LS7 _DC 50
G_LS6 51
G_LS5 52
G_LS4 53
G_LS3 54
G_LS2 55
G_LS1 56
VBOOST
57
B_HS7 58
G_HS7 59
S_HS7 60
B_HS6 61
G_HS6 62
S_HS6 63
B_HS5 64
G_HS5 65
S_HS5 66
B_HS4 67
G_HS4 68
S_HS4 69
B_HS3 70
G_HS3 71
S_HS3 72
B_HS2 73
G_HS2 74
S_HS2 75
B_HS1 76
G_HS1 77
S_HS1 78
IRQ/FLAG_13
79
CLK
80
EP_GND
81
START1/FLAG_5
3
START2/FLAG_6
4
START3/FLAG_7
5
START4/FLAG_8
6
START5/FLAG_9
7
START6/FLAG_10
8
START7/FLAG_11
9
C_BATT4
0.1UF
U5D
ULN2003ADR
4B
4COM 9
4C 13
E8
J9
HDR_2X8
1 2
3 4
65
7 8
910
11 12
13 14
15 16
TP25
1
START4
1
SH1 0
R41
470
R_GLS8b 1.0
START5
1
R_OA3 0
U5E
ULN2003ADR
5B
5COM 9
5C 12
E8
TP26
1
JCLK
HDR 1X2 TH
1
2
C_VCC2P5_2
0.1uF
SH2 0
START6
1
TP20
1
Q8
AOD4185
1
3 4
R42
470
Q31
BUK9230-100B
1
3 4
C_BATT7
0.01UF
FLAG3
1
FLAG4
1
D19
RED LED
SILK = F0
AC
J10
HDR_2X6
1 2
3 4
6
5
7 8
910
11 12
R37 100K
R43
470
START7
1
C_OA2
1000pF
D20
RED LED
SILK = F1
A
C
L2
10UH
12
D16
GREEN
SILK = +5V
AC
TP21
1
C40
4.7uF
C_VCCP1
0.1uF
D17
MMSZ5245B
A C
DBG
1
C_VCC2P5_1
1UF
U4
MC78L05ACHX
VIN
3VOUT 1
GND
2
R36
470
D21
RED LED
SILK = F2
AC
R_VSENSE6
0.01
C_OA3
1000pF
G_LS8
1
+
C_BATT1
470uF
C_BOOST4
0.022UF
D22
RED LED
SILK = F3
AC
C41
1UF
MOSI
1
+
C_BATT3
470uF
OA2
1
OA3
1
TP15
1
D23
RED LED
SILK = USB_PWR
AC
C44
0.1uF
C_VSENSE6
330pF
D36
SMBJ40
A C
START8
1
R_OA1 0
J6
TB 1X2
1
2
D9
FFD10UP20S
3
4
1
TP16
1
L_BATTERY
6uH
1 2
C_OA1
1000pF
J7
HDR_10X2
12
3 4
65
78
910
11 12
13 14
15 16
17 18
19 20
MISO
1
SCLK
1
TP17
1
TP22
1
R44
470
START1
1
C_BOOST5
0.22uF
100V
OA1
1
+
C_BOOST6
680uF
TP23
1
RSTB
1
U5A
ULN2003ADR
1B
11C 16
COM 9
E8
R_GLS8a 2.2
C_VCCIO
0.1uF
IRQB
1
C_GLS8
4700PF
FLAG0
1
START2
1
C_RES
0.1uF
DNP
FLAG1
1
J8
HDR_2X8
1 2
34
6
5
78
910
11 12
13 14
15 16
U5B
ULN2003ADR
2B
2COM 9
E8
2C 15
JVCCIO
HDR 1X2 TH
1
2
C45
10uF
R_OA2 0
R10
5.1
C_VCC5
0.1uF
C_VCCP2
4.7uF
TP24
1
TP18
1
U5C
ULN2003ADR
3B
33C 14
COM 9
E8
START3
1
CSB
1
C_BATT2
0.1UF
R40
470
TP19
1
FLAG2
1
C_BATT5
0.1uF
Schematics
KTPT2000FRDM6CUG Rev. 2.0
Freescale Semiconductor, Inc. 21
Figure 10. KITPT2000FRDM6C Evaluation Board Schematic Part 2
INJECTOR BANK1
SH3 needs to be
placed close to
R_VSENSE1
INJECTOR BANK2
INJECTOR BANK3
FUEL PUMP
VPWR
VPWR
VPWR
VPWR
VPWR
G_HS2
B_HS2
S_HS2
G_HS1
B_HS1
S_HS1
D_LS1
G_LS1
VBOOST
VBOOST
VSENSEN1
VSENSEP1
D_LS2
VBOOST
G_LS2
G_HS4
B_HS4
S_HS4
G_HS3
B_HS3
S_HS3
D_LS3
G_LS3
VBOOST
VBOOST
VSENSEN2
VSENSEP2
D_LS4
VBOOST
G_LS4
G_HS6
B_HS6
S_HS6
G_HS5
B_HS5
S_HS5
D_LS5
G_LS5
VBOOST
VBOOST
VSENSEN3
VSENSEP3
D_LS6
VBOOST
G_LS6
D_LS7
G_LS7
VSENSEP5
VSENSEN5
G_HS7
B_HS7
S_HS7
R_GSHS7
510K
C_MHS4 330PF
DNP
R_GLSb1 332
D_SHS14
RURD620CCS9A_F085
3
1
4
SH3 0
D34STPS2H100UY
A C
Q23
BUK9230-100B
1
3 4
C_BHS7
1UF
C_GSHS3
1000pF
C_VSENSE3
330pF
C_BHS6
0.1uF
SH6 0
C_INJP4
4700PF
D29STPS2H100UY
A C
C_GSHS1
1000pF
D33
TPSMB15ATG
DNP
AC
Q30
BUK9230-100B
1
3 4
G_HS6
1
C_BATT_HS7
2.2UF
R_VSENSE3
0.015
D_SHS13
RURD620CCS9A_F085
3
1
4
SH15 0
G_HS7
1
G_LS7
1
D32STPS2H100UY
A C
D24STPS2H100UY
A C
C_INJP1
4700PF
C_BHS4
0.1uF
C_GLS5
2200PF
SH17
0
C_INJN4
4700PF
C_MLS5 330PF
DNP
C_BHS2
0.1uF
C_VSENSE2
330pF
D27STPS2H100UY
A C
C_INJN6
4700PF
C_MLS2 330PF
DNP
Q26
BUK9230-100B
1
3 4
SH16 0
G_HS1
1
SH13 0
C_BHS5
1UF
C_BATT_HS1
2.2UF
Q10
BUK9230-100B
1
3 4
R_GHSb5 332
G_HS5
1
R_GLSb2 332
R_VSENSE2
0.015
J12
OSTTG025100B
1
2
G_LS5
1
C_INJP3
4700PF
C_GLS3
2200PF
C_MLS1 330PF
DNP
R_GSHS5
510K
C_INJN1
4700PF
C_INJN5
4700PF
C_MLS3 330PF
DNP
C_GLS1
2200PF
R_GHSb2 332
SH14 0
C_GSHS6
2200PF
G_LS2
1
C_BHS3
1UF
Q12
BUK9230-100B
1
3 4
C_BATT_HS5
2.2UF
D18
STPS2H100UY
A C
VSENSEP1
1
R_GHSb1 332
R_GHSb3 332
G_HS2
1
C_INJP7
4700PF
R_GSHS6
510K
C_INJP2
4700PF
C_INJN3
4700PF
J11
OSTTG025100B
1
2
C_VSENSE5
330pF
R_GSHS3
510K
R_GHSb6 332
C_MHS2 330PF
DNP
Q11
BUK9230-100B
1
3 4
C_GSHS4
2200PF
G_LS6
1
C_MLS6 330PF
DNP
C_INJP6
4700PF
Q28
BUK9230-100B
1
3 4
C_MHS1 330PF
DNP
C_GLS2
2200PF
C_GSHS2
2200PF
R_VSENSE1
0.015
R_VSENSE5
0.015
C_BATT_HS3
2.2UF
G_LS1
1
J19
OSTTG025100B
1
2
R_GHSb7 332
R_GLSb6 332
Q22
BUK9230-100B
1
3 4
D25STPS2H100UY
A C
R_GSHS4
510K
C_INJN7
4700PF
C_MHS5 330PF
DNP
C_INJN2
4700PF
SH11 0
VSENSEN1
1
R_GHSb4 332
C_VSENSE1
330pF
G_HS3
1
Q29
BUK9230-100B
1
3 4
C_MHS7 330PF
DNP
C_MLS4 330PF
DNP
C_INJP5
4700PF
C_MLS7 330PF
DNP
Q24
BUK9230-100B
1
3 4
D_SHS12
RURD620CCS9A_F085
3
1
4
G_LS3
1
R_GLSb5 332
C_GLS6
2200PF
J21
OSTTG025100B
1
2
J18
OSTTG025100B
1
2
R_GSHS2
510K
R_GLSb4 332
J16
OSTTG025100B
1
2
C_GSHS7
1000pF
C_MHS3 330PF
DNP
C_BHS1
1UF
C_MHS6 330PF
DNP
Q13
BUK9230-100B
1
3 4
R_GLS7 332
Q25
BUK9230-100B
1
3 4
SH12 0
D30
STPS2H100UY
A C
Q27
BUK9230-100B
1
3 4
R_GLSb3 332
C_GSHS5
1000pF
Q32
BUK9230-100B
1
3 4
C_GLS4
2200PF
R_GSHS1
510K
G_HS4
1
C_GLS7
2200PF
J14
OSTTG025100B
1
2
G_LS4
1
Silkscreen
KTPT2000FRDM6CUG Rev. 2.0
22 Freescale Semiconductor, Inc.
8 Silkscreen
8.1 Silkscreen Top
Figure 11. KITPT2000FRDM6C Silk Screen Top Layer
Bill of Materials
KTPT2000FRDM6CUG Rev. 2.0
Freescale Semiconductor, Inc. 23
9 Bill of Materials
Table 9. Bill of Materials (2)
Item Qty. Schematic Label Value Description Part Number Assy.
Opt.
Freescale Components
1 1 U1 IC DRV 1.0 MHZ Auto 5.0-36 V LQFP80 MC33PT2000AC (4)
Active Components
21U4 MC78L05AC
HX IC VREG 5.0 V 100 mA 30 V SOT-89
3 1 U5 ULN2003ADR IC Tran Array NPN DARL Seven 50 V
0.5 A SOIC16
4 1 L2 10 HInd PWR 10 H at 100 KHZ 16 A 20%
SMT
5 1 L_BATTERY 6.0 HInd Rod Chk 6.0 H at 10 kHZ 10 A 25%
TH
6 1 Q8 AOD4185 Tran PMOS PWR 40 A 40 V TO252
715
Q10, Q11, Q12, Q13, Q22, Q23, Q24,
Q25, Q26, Q27, Q28, Q29, Q30, Q31,
Q32
BUK9230-100
BTran NMOS PWR SW 47A 100 V DPAK
Diodes
8 1 D9 FFD10UP20S Diode SW UF 10 A 200 V TO252
9 1 D16 Green LED GRN SGL 30 MA SMT 0805
10 1 D17 MMSZ5245B Diode ZNR -- 15 V 0.5 W SOD123
11 8 D18, D24, D25, D27, D29, D30, D32,
D34
STPS2H100U
Y
Diode SCH RECT 2.0 A 100 V
AEC-Q101 SMB
12 5 D19, D20, D21, D22, D23 Red Led LED RED SGL 30 MA SMT 0805
13 1 D33 TPSMB15AT
G
Diode TVS UNIDIR 100 A 600 W 15 V
AEC-Q101 DO214AA
14 1 D36 SMBJ40 Diode TVS 9.3 A 40 V SMB SMT
15 3 D_SHS12, D_SHS13, D_SHS14 RURD620CC
S9A_F085 Diode Dual 6.0 A 200 V TO252AA
Capacitors
16 15
C24, C_MHS1, C_MHS2, C_MHS3,
C_MHS4, C_MHS5, C_MHS6, C_MHS7,
C_MLS1, C_MLS2, C_MLS3, C_MLS4,
C_MLS5, C_MLS6, C_MLS7
330 pF Cap Cer 330 pF 100 V 5% C0G 0805
17 2 C40, C_VCCP2 4.7 F Cap Cer 4.7 F 50V 20% X5R 0805
18 6 C41, C_BHS1, C_BHS3, C_BHS5,
C_BHS7, C_VCC2P5_1 1.0 FCap Cer 1.0 F 25 V 10% X7R
AEC-Q200 0603
19 9
C44, C_BATT5, C_BHS2, C_BHS4,
C_BHS6, C_VCC2P5_2, C_VCC5,
C_VCCIO, C_VCCP1
0.1 FCap Cer 0.1 F 50 V 10% X7R
AEC-Q200 0603
20 1 C45 10 F Cap Cer 10 F 10 V 20% X5R 0603
21 2 C_BATT1, C_BATT3 470 F Cap Alel 470 F 35 V 20% -- RADIAL
22 2 C_BATT2, C_BATT4 0.1 F Cap Cer 0.1 F 200 V 10% X7R 1206
23 1 C_BATT7 0.01 F Cap Cer 0.01 F 100 V 10% X7R 0805
Bill of Materials
KTPT2000FRDM6CUG Rev. 2.0
24 Freescale Semiconductor, Inc.
24 4 C_BATT_HS1, C_BATT_HS3,
C_BATT_HS5, C_BATT_HS7 2.2 F Cap Cer 2.2 F 25 V 10% X7R 0805
25 1 C_BOOST4 0.022 F Cap Cer 0.022 F 50 V 10% X7R 0805
26 1 C_BOOST5 0.22uF Cap Cer 0.22 F 100 V 20% X7S 0805
27 1 C_BOOST6 680 F Cap Alel 680 F 100 V 20% -- RADIAL
28 10
C_GLS1, C_GLS2, C_GLS3, C_GLS4,
C_GLS5, C_GLS6, C_GLS7, C_GSHS2,
C_GSHS4, C_GSHS6
2200 pF Cap Cer 2200 pF 25 V 20% X7R 0805
29 15
C_GLS8, C_INJN1, C_INJN2, C_INJN3,
C_INJN4, C_INJN5, C_INJN6, C_INJN7,
C_INJP1, C_INJP2, C_INJP3, C_INJP4,
C_INJP5, C_INJP6, C_INJP7
4700 pF Cap Cer 4700 pF 100 V 10% X7R 0805
30 7 C_GSHS1, C_GSHS3, C_GSHS5,
C_GSHS7, C_OA1, C_OA2, C_OA3 1000 pF Cap Cer 1000 pF 50 V 10% X7R 0805
31 1 C_RES 0.1 FCap Cer 0.1 F 100 V 10% X7R
AEC-Q200 0805
(3)
32 5
C_VSENSE1, C_VSENSE2,
C_VSENSE3, C_VSENSE5,
C_VSENSE6
330 pF Cap Cer 330 pF 25 V 10% X7R 0603
Resistors
33 1 R10 5.1 Res MF 5.1 1/10 W 5% 0603
34 6 R36, R40, R41, R42, R43, R44 470 Res MF 470 1/10 W 5% 0603
35 1 R37 100k Res MF 100 k 1/10 W 5% 0603
36 14
R_GHSB1, R_GHSB2, R_GHSB3,
R_GHSB4, R_GHSB5, R_GHSB6,
R_GHSB7, R_GLS7, R_GLSB1,
R_GLSB2, R_GLSB3, R_GLSB4,
R_GLSB5, R_GLSB6
332 Res MF 332 1/8 W 1% 0805
37 1 R_GLS8A 2.2 Res MF 2.20 1/8 W 1% 0805
38 1 R_GLS8B 1.0 Res MF 1.0 1/8 W 1% 0805
39 7
R_GSHS1, R_GSHS2, R_GSHS3,
R_GSHS4, R_GSHS5, R_GSHS6,
R_GSHS7
510k Res MF 510 k 1/8 W 5% 0805
40 3 R_OA1, R_OA2, R_OA3 0 Res MF Zero 1/8 W AEC-Q200 0805
41 4 R_VSENSE1, R_VSENSE2,
R_VSENSE3, R_VSENSE5 0.015 Res MF 0.015 2.0 W 1% 2512
42 1 R_VSENSE6 0.01 Res MF 0.01 1.0 W 1% 2512
43 11 SH1, SH2, SH3, SH6, SH11, SH12,
SH13, SH14, SH15, SH16, SH17 0Zero Cut Trace 0603 PADS; No Part
to Order
Switches, Connectors, Jumpers and Test Points
44 1 J6 TB 1X2 Con 1X2 TB TH 5.0 mm 12.9 mm SN
150L
45 1 J7 HDR_10X2 HDR 2X10 TH 100 MIL CTR 330H AU
100L
46 2 J8, J9 HDR_2X8 HDR 2X8 TH 100 MIL CTR 330H AU
47 1 J10 HDR_2X6 HDR 2X6 TH 100 MIL CTR 330H AU
48 7 J11, J12, J14, J16, J18, J19, J21 OSTTG02510
0B Con 1X2 TB TH 5.08 mm 504H -- 177L
Table 9. Bill of Materials (2) (continued)
Item Qty. Schematic Label Value Description Part Number Assy.
Opt.
Bill of Materials
KTPT2000FRDM6CUG Rev. 2.0
Freescale Semiconductor, Inc. 25
49 2 JCLK, JVCCIO HDR 1X2 TH HDR 1X2 TH 100 MIL SP 339H AU 98L
50 52
CSB, DBG, FLAG0, FLAG1, FLAG2,
FLAG3, FLAG4, G_HS1, G_HS2,
G_HS3, G_HS4, G_HS5, G_HS6,
G_HS7, G_LS1, G_LS2, G_LS3, G_LS4,
G_LS5, G_LS6, G_LS7, G_LS8, IRQB,
MISO, MOSI, OA1, OA2, OA3, RSTB,
SCLK, START1, START2, START3,
START4, START5, START6, START7,
START8, TP15, TP16, TP17, TP18,
TP19, TP20, TP21, TP22, TP23, TP24,
TP25, TP26, VSENSEN1, VSENSEP1
3.65x2.05 mm Test Point 3.65x2.05 mm SMT
Notes
2. Freescale does not assume liability, endorse, or warrant components from external manufacturers are referenced in circuit drawings or tables.
While Freescale offers component recommendations in this configuration, it is the customer’s responsibility to validate their application.
3. Do not populate, except in Resonant mode.
4. Critical components. For critical components, it is vital to use the manufacturer listed.
Table 9. Bill of Materials (2) (continued)
Item Qty. Schematic Label Value Description Part Number Assy.
Opt.
References
KTPT2000FRDM6CUG Rev. 2.0
26 Freescale Semiconductor, Inc.
10 References
The following URLs are where you can obtain information on related Freescale products and application solutions:
10.1 Support
Visit www.freescale.com/support for a list of phone numbers within your region.
10.2 Warranty
Visit www.freescale.com/warranty for a list of phone numbers within your region.
Freescale.com
Support Pages Description URL
KITPT2000FRDM3C Tool Summary Page http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=KITPT2000FRDM3C
KITPT2000FRDM6C Tool Summary Page http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=KITPT2000FRDM6C
PT2000-IDEUG Developer Studio
User’s Guide http://www.freescale.com/files/analog/doc/user_guide/PT2000-IDEUG.pdf
PT2000 Product Summary
Page http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=PT2000
FRDM-KL25Z Tool Summary Page http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=FRDM-KL25Z
SPIGen Tool Summary Page http://www.freescale.com/webapp/sps/site/prod_summary.jsp?&code=SPIGEN
Analog Home Page http://www.freescale.com/analog
Automotive Home Page http://www.freescale.com/automotive
Document Number: KTPT2000FRDM6CUG
Rev. 2.0
6/2015
Information in this document is provided solely to enable system and software implementers to use Freescale products.
There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits based
on the information in this document.
Freescale reserves the right to make changes without further notice to any products herein. Freescale makes no
warranty, representation, or guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any
and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be
provided in Freescale data sheets and/or specifications can and do vary in different applications, and actual performance
may vary over time. All operating parameters, including “typicals,” must be validated for each customer application by
customer’s technical experts. Freescale does not convey any license under its patent rights nor the rights of others.
Freescale sells products pursuant to standard terms and conditions of sale, which can be found at the following address:
freescale.com/SalesTermsandConditions.
Freescale and the Freescale logo are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off.
SMARTMOS is a trademark of Freescale Semiconductor, Inc. All other product or service names are the property of their
respective owners.
© 2015 Freescale Semiconductor, Inc.
How to Reach Us:
Home Page:
freescale.com
Web Support:
freescale.com/support
