CENTIGRID(R) ESTABLISHED RELIABILITY RELAYS SERIES 134 ESTABLISHED RELIABILITY SENSITIVE DPDT SERIES DESIGNATION RELAY TYPE 134 DPDT basic relay 134D DPDT relay with internal diode for coil transient suppression DPDT relay with internal diodes for coil transient suppression and polarity reversal protection 134DD INTERNAL CONSTRUCTION DESCRIPTION UNI-FRAME UPPER STATIONARY CONTACT ARMATURE LOWER STATIONARY CONTACT MOVING CONTACT ENVIRONMENTAL AND PHYSICAL SPECIFICATIONS Temperature (Ambient) -65C to +125C Vibration (General Note 1) 30 g's to 3000 Hz Shock (General Note 1) 75 g's, 6 msec, half-sine Acceleration 50 g's Enclosure Hermetically sealed Weight 0.15 oz. (4.3g) max. 134 Page 1 The 134 sensitive Centigrid(R) relay retains the same features as the 114 standard Centigrid(R) relay with only a minimal increase in profile height (.375 in.). Its .100-inch grid spaced terminals, which preclude the need for spreader pads, and its low profile make the 134 relay ideal for applications where high packaging density is important. The following unique construction features and manufacturing techniques provide excellent resistance to environmental extremes and overall high reliability: * All welded construction. * Unique uni-frame design providing high magnetic efficiency and mechanical rigidity. * High force/mass ratios for resistance to shock and vibration. * Advanced cleaning techniques provide maximum assurance of internal cleanliness. * Precious metal alloy contact material with gold plating assures excellent high current and dry circuit switching capabilities. The Series 134D and 134DD have internal discrete silicon diodes for coil suppression and polarity reversal protection. The sensitive 134 Centigrid(R) relay has a high resistance coil, thus requiring extremely low operating power (200 mw typical). The advantages of reduced heat dissipation and power supply demands are a plus. By virtue of its inherently low intercontact capacitance and contact circuit losses, the 134 relay has proven to be an excellent ultraminiature RF switch for frequency ranges well into the UHF spectrum. A typical RF application for the Centigrid(R) relay is in handheld radio transceivers, wherein the combined features of good RF performance, small size, low coil power dissipation and high reliability make it a preferred method of Transmit-Receive switching (see Figure 1). SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE www.teledynerelays.com (c)2004 TELEDYNE RELAYS 134/0704/Q1 SERIES 134 GENERAL ELECTRICAL SPECIFICATIONS (-65C to +125C unless otherwise noted) (Notes 2 & 3) Contact Arrangement Rated Duty Contact Resistance 2 Form C (DPDT) Continuous 0.1 ohm max. before life; 0.2 ohm max. after life at 1A/28Vdc (measured 1/8" from header) Contact Load Ratings (DC) (See Fig. 2 for other DC resistive voltage/current ratings) Resistive: Inductive: Lamp: Low Level: 1 Amp/28Vdc 200 mA/28Vdc (320 mH) 100 mA/28Vdc 10 to 50 A/10 to 50mV Resistive: 250 mA/115Vac, 60 and 400 Hz (Case not grounded) 100 mA/115Vac, 60 and 400 Hz (Case grounded) Contact Life Ratings 10,000,000 cycles (typical) at low level 1,000,000 cycles (typical) at 0.5A/28Vdc resistive 100,000 cycles min. at all other loads specified above Contact Overload Rating Contact Carry Rating Coil Operating Power Operate Time Release Time Contact Bounce Intercontact Capacitance Insulation Resistance Dielectric Strength Negative Coil Transient (Vdc) Diode P.I.V. (Vdc) 2A/28Vdc Resistive (100 cycles min.) Contact factory 200 milliwatts typical at nominal rated voltage @ 25C 4.0 msec max. at nominal rated coil voltage 134 Series: 2.0 msec max. 134D, 134DD Series: 7.5 msec max. 1.5 msec max. 0.4 pf typical 10,000 megohms min. between mutually isolated terminals Atmospheric pressure: 500 Vrms/60Hz 70,000 ft.: 125 Vrms/60Hz 134D, 134DD 1.0 max 134D, 134DD 100 min. DETAILED ELECTRICAL SPECIFICATIONS (-65C to +125C unless otherwise noted) (Note 3) BASE PART NUMBERS (See Note 8 for full P/N example) 134-5 134D-5 134DD-5 134-6 134D-6 134DD-6 134-9 134D-9 134DD-9 134-12 134D-12 134DD-12 134-18 134D-18 134DD-18 134-26 134D-26 134DD-26 5.0 7.5 100 64 56.8 78.1 3.5 3.7 0.12 2.5 0.7 2.6 6.0 10.0 200 125 36.3 48.9 4.5 4.8 0.18 3.2 0.8 3.0 9.0 15.0 400 400 18.1 23.6 6.8 8.0 0.35 4.9 0.9 4.5 12.0 20.0 800 800 12.5 16.0 9.0 11.0 0.41 6.5 1.0 5.8 18.0 30.0 1600 1600 9.6 12.2 13.5 14.5 0.59 10.0 1.1 9.0 26.5 40.0 3200 3200 7.2 9.0 18.0 19.0 0.89 13.0 1.3 13.0 Nom. Max. 134, 134D 134DD (Note 4) Min. Max. 134, 134D 134DD Min. 134, 134D Max. Min. 134DD Max. Coil Voltage (Vdc) Coil Resistance (Ohms 10% @25C) Coil Current (mAdc @25C) (134DD Series) Pick-up Voltage (Vdc, Max.) Drop-out Voltage (Vdc) PERFORMANCE CURVES (NOTE 2) TYPICAL RF PERFORMANCE 0 TYPICAL DC CONTACT RATING (RESISTIVE) INSE .2 300 LOS S .3 .4 1.92 SWR) SS (V RN LO 20 RETU 30 40 N ATIO CT NTA S CO OS ACR N ATIO 60 1.07 S ISOL 50 1.22 ISOL 1.02 LES PO ROSS AC 1.01 1.00 70 VSWR 10 LOAD VOLTAGE (VDC) RTIO N .1 dB ESTABLISHED RELIABILITY Contact Load Ratings (AC) 250 200 150 100 50 1.00 .01 0.5 .1 .5 1.0 0 0.1 0.2 0.3 0.4 0.5 0.6 FREQUENCY (GHz) LOAD CURRENT (AMPS DC) FIGURE 1 FIGURE 2 (c)2003 TELEDYNE RELAYS SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE www.teledynerelays.com 0.7 0.8 0.9 1.0 134 Page 2 134/1203/Q1 SERIES 134 SCHEMATIC DIAGRAMS OUTLINE DIMENSIONS CASE DETAIL .375 (9.53) SQ. MAX. TERMINAL LOCATIONS (Viewed from Terminals; Numbers for Reference Only) .031 .003 (.79 .08) .335 (8.51) SQ. MAX. .375 (9.53) MAX. .035 .010 (.89 .25) 7 8 +.002 (.05) DIA. -.001 (.03) 3 5 ESTABLISHED RELIABILITY .017 (.43) .100 .010 (2.54 .25) TYP 8 PLACES 2 6 WIRE LEAD .750 (19.05) MIN. PIN: .187 (1.75) .010 (.25) (See Note 5) 134 1 4 DIMENSIONS ARE SHOWN IN INCHES (MILLIMETERS) 134D GENERAL NOTES 1. Relay contacts will exhibit no chatter in excess of 10 sec or transfer in excess of 1 sec. 2. "Typical" characteristics are based on available data and are best estimates. No on-going verification tests are performed. 3. Unless otherwise specified, parameters are initial values. 4. For reference only. Coil resistance not directly measurable at relay terminals due to internal series diode in 134DD only. 5. Unless otherwise specified, relays will be supplied with either gold-plated or soldercoated leads. 6. The slash and characters appearing after the slash are not marked on the relay. 7. Screened HI-REL versions available. Contact factory. 8. 134DD SCHEMATICS ARE VIEWED FROM TERMINALS Teledyne Part Numbering System for T2R(R) Established Reliability Relay ER 134 Z M4 - 26 A / S Q Established Reliability Designator Q= Solder-Coated Leads G= Gold-Plated Leads (Notes 5 and 6) Relay Series Ground Pin Option (See Appendix) S= .187" leads (Note 6) Screening and Reliability Level Pad Option (See Appendix) Coil Voltage Teledyne Part Numbering System for Military Qualified (JAN) Relays J 134 Z M4 - 26 P L Military (JAN) Designator Screening and Reliability Level Relay Series Ground Pin Option (See Appendix) Terminal Variant P = 0.187" Coil Voltage Pad Option (See Appendix) 134 Page 3 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE www.teledynerelays.com (c)2004 TELEDYNE RELAYS 134/0704/Q1 Appendix A: Spacer Pads Pad designation and bottom view dimensions Height O.150 [3.81] (REF) Dim H MAX "M4" Pad for TO-5 Dim H MAX "M4" Pad for TO-5 Dim H MAX "M4" Pad for Centigrid(R) .156 [3.96] (REF) Dim H MAX .256 [6.5] (REF) "M9" Pad for Centigrid(R) For use with the following: ER411T ER412, ER412D, ER412DD 712, 712D, 712TN, RF300, RF310, RF320 ER420, ER422D, ER420DD, 421, ER421D, ER421DD, ER422, ER422D, ER422DD, 722, 722D, RF341 ER431T, ER432T, ER432, ER432D, ER432DD 732, 732D, 732TN, RF303, RF313, RF323 .295 (7.49) .300 (7.62) .305 (7.75) .400 (10.16) .410 (10.41) RF312 .350 (8.89) ER411, ER411D, ER411DD .295 (7.49) ER431, ER431D, ER431DD .400 (10.16) RF311 .300 (7.62) RF331 .410 (10.41) 172, 172D .305 (7.75) ER114, ER114D, ER114DD, J114, J114D, J114DD .300 (7.62) ER134, ER134D, ER134DD, J134, J134D, J134DD .400 (10.16) RF100 .315 (8.00) RF103 .420 (10.67) 122C, A152 .320 (8.13) ER116C, J116C .300 (7.62) ER136C, J136C .400 (10.16) RF180 .325 (8.25) A150 .305 (7.75) Notes: 1. Spacer pad material: Polyester lm. 2. To specify an "M4" or "M9" spacer pad, refer to the mounting variants portion of the part numbering example in the applicable datasheet. 3. Dimensions are in inches (mm). 4. Unless otherwise specied, tolerance is .010 (.25). 5. Add 10 m to the contact resistance show in the datasheet. 6. Add 0.01 oz. (0.25 g) to the weight of the relay assembly shown in the datasheet. (c) 2008 Teledyne Relays Dim. H Max. SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Appendix A: Spreader Pads Pad designation and bottom view dimensions Height For use with the following: .370 [9.4] MAX SQ .100 [2.54] Dim H MAX .150 [3.81] .014 [0.36] (REF) .300 [7.62] .100 [2.54] .370 [9.4] MIN .200 [5.08] "M" Pad 5/ 6/ .390 [9.91] SQ .100 [2.54] .100 [2.54] .150 [3.81] .300 [7.62] .300 [7.62] .150 [3.81] Dim H MAX ER411T, J411T, ER412, ER412D ER412DD, J412, J412D, J412DD ER412T, J412T 712, 712D, 712TN ER431T, J431T, ER432, ER432D ER432DD, J432, J432D, J432DD ER432T, J432T 732, 732D, 732TN .370 [9.4] MAX SQ .100 [2.54] Dim H MAX .150 [3.81] .014 [0.36] (REF) .300 [7.62] .100 [2.54] .200 [5.08] .370 [9.4] MIN "M3" Pad 5/ 6/ 9/ .393 (9.99) .493 (12.52) .503 (12.78) .398 (10.11) ER411T ER412, ER412D, ER412DD J412, J412D, J412DD .441 (11.20) 732, 732D "M2" Pad 7/ 8/ .388 (9.86) ER420, J420, ER420D, J420D ER420DD, J420DD, ER421, J421 ER421D, J421D, ER421DD J422D, ER422DD, J422DD, 722 712, 712D ER421, ER421D, ER421DD 722, 732D ER431T ER432, ER432D, ER432DD .130 [3.3] Dim. H Max. ER411, ER411D, ER411DD ER411TX ER412X, ER412DX, ER412DDX ER412TX 712X, 712DX, 712TNX ER420X, ER420DX, ER420DDX ER421X, ER421DX, ER421DDX ER422X, ER422DX ER422DDX, 722X, 722DDX ER431, ER431D, ER431DD ER431TX ER432X, ER432DX, ER432DDX ER432TX 732X, 732DX, 732TNX .451 (11.46) .451 (11.46) .546 (13.87) .556 (14.12) .388 (9.86) .393 (9.99) .398 (10.11) .493 (12.52) .503 (12.78) Notes: 1. Spreader pad material: Diallyl Phthalate. 2. To specify an "M", "M2" or "M3" spreader pad, refer to the mounting variants portion of the part number example in the applicable datasheet. 3. Dimensions are in inches (mm). 4. Unless otherwise specied, tolerance is .010" (0.25). 5/. Add 25 m to the contact resistance shown in the datasheet. 6/. Add .01 oz. (0.25 g) to the weight of the relay assembly shown in the datasheet. 7/. Add 50 m to the contact resistance shown in the datasheet. 8/. Add 0.025 oz (0.71 g) to the weight of the relay assembly shown in the datasheet. 9/. M3 pad to be used only when the relay has a center pin (e.g. ER411M3-12A, 722XM3-26.) (800) 284-7007 * www.teledynerelays.com +44 (0) 1236 453124 * www.teledyne-europe.com (c) 2008 Teledyne Relays Appendix A: Ground Pin Positions O.200 [O5.08] 363 "Z" POSITION "X" POSITION "Y" POSITION "Z" O.200 [O5.08] "Y" 453 TO-5 Relays: ER411T, ER412, ER412T, ER420, ER421, ER422, ER431T, ER432, ER432T, 712, 712TN, 400H, 400K, 400V, RF300, RF303, RF341, RF312, RF310, RF313, RF320, RF323 "Y" POSITION POSITION TO-5 Relays: ER411, ER431, RF311, RF331 POSITION .100 [2.54] "W" "Z" .100 [2.54] .050 [1.27] "X" .100 [2.54] POSITION POSITION "Z" POSITION POSITION .100 [2.54] POSITION "U" POSITION (ER116C and ER136C only) Centigrid(R) Relays: RF180, ER116C, 122C, ER136C .100 [2.54] Centigrid(R) Relays: RF100, RF103, ER114, ER134, 172 Indicates ground pin position Indicates glass insulated lead position Indicates ground pin or lead position depending on relay type (c) 2008 Teledyne Relays "Y" .100 [2.54] NOTES 1. Terminal views shown 2. Dimensions are in inches (mm) 3. Tolerances: .010 (.25) unless otherwise specied 4. Ground pin positions are within .015 (0.38) dia. of true position 5. Ground pin head dia., 0.035 (0.89) ref: height 0.010 (0.25) ref. 6. Lead dia. 0.017 (0.43) nom. SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE