LMH6321TSX NOPB - TEXAS INSTRUMENTS

www.teledynerelays.com 134/0704/Q1

ESTABLISHED RELIABILITY

SERIES

134

CENTIGRID®

ESTABLISHED RELIABILITY

RELAYS

SENSITIVE DPDT

DESCRIPTION

The 134 sensitive Centigrid®relay retains the same features as the 114

standard Centigrid®relay with only a minimal increase in profile height (.375

in.). Its .100-inch grid spaced terminals, which preclude the need for spreader

pads, and its low profile make the 134 relay ideal for applications where high

packaging density is important.

The following unique construction features and manufacturing techniques

provide excellent resistance to environmental extremes and overall high

reliability:

• All welded construction.

• Unique uni-frame design providing high magnetic efficiency and mechanical

rigidity.

• High force/mass ratios for resistance to shock and vibration.

• Advanced cleaning techniques provide maximum assurance of internal

cleanliness.

• Precious metal alloy contact material with gold plating assures excellent

high current and dry circuit switching capabilities.

The Series 134D and 134DD have internal discrete silicon diodes for coil

suppression and polarity reversal protection.

The sensitive 134 Centigrid®relay has a high resistance coil, thus requiring

extremely low operating power (200 mw typical). The advantages of reduced

heat dissipation and power supply demands are a plus.

By virtue of its inherently low intercontact capacitance and contact circuit

losses, the 134 relay has proven to be an excellent ultraminiature RF switch

for frequency ranges well into the UHF spectrum. A typical RF application for

the Centigrid®relay is in handheld radio transceivers, wherein the combined

features of good RF performance, small size, low coil power dissipation and

high reliability make it a preferred method of Transmit-Receive switching (see

Figure 1).

INTERNAL CONSTRUCTION

SERIES

DESIGNATION RELAY TYPE

134 DPDT basic relay

134D DPDT relay with internal diode for coil transient suppression

134DD DPDT relay with internal diodes for coil transient suppression and polarity

reversal protection

UPPER

STATIONARY

CONTACT

LOWER

ATIONARY

CONTACT MOVING

CONTACT

UNI-FRAME

ARMA

TURE

ENVIRONMENTAL AND

PHYSICAL SPECIFICATIONS

Temperature

(Ambient) –65°C to +125°C

Vibration

(General Note 1) 30 g’s to 3000 Hz

Shock

(General Note 1)

75 g’s,

6 msec, half-sine

Acceleration 50 g’s

Enclosure Hermetically sealed

Weight 0.15 oz. (4.3g) max.

PERFORMANCE CURVES

(NOTE 2)

www.teledynerelays.com 134/1203/Q1

ESTABLISHED RELIABILITY

SERIES 134

GENERAL ELECTRICAL SPECIFICATIONS (–65°C to +125°C unless otherwise noted) (Notes 2 & 3)

DETAILED ELECTRICAL SPECIFICATIONS (–65°C to +125°C unless otherwise noted) (Note 3)

Contact Arrangement 2 Form C (DPDT)

Rated Duty Continuous

Contact Resistance 0.1 ohm max. before life; 0.2 ohm max. after life at 1A/28Vdc (measured 1/8" from header)

Contact Load Ratings (DC)

(See Fig. 2 for other DC

resistive voltage/current ratings)

Resistive: 1 Amp/28Vdc

Inductive: 200 mA/28Vdc (320 mH)

Lamp: 100 mA/28Vdc

Low Level: 10 to 50 μA/10 to 50mV

Contact Load Ratings (AC) Resistive: 250 mA/115Vac, 60 and 400 Hz (Case not grounded)

100 mA/115Vac, 60 and 400 Hz (Case grounded)

Contact Life Ratings

10,000,000 cycles (typical) at low level

1,000,000 cycles (typical) at 0.5A/28Vdc resistive

100,000 cycles min. at all other loads specified above

Contact Overload Rating 2A/28Vdc Resistive (100 cycles min.)

Contact Carry Rating Contact factory

Coil Operating Power 200 milliwatts typical at nominal rated voltage @ 25°C

Operate Time 4.0 msec max. at nominal rated coil voltage

Release Time 134 Series: 2.0 msec max. 134D, 134DD Series: 7.5 msec max.

Contact Bounce 1.5 msec max.

Intercontact Capacitance 0.4 pf typical

Insulation Resistance 10,000 megohms min. between mutually isolated terminals

Dielectric Strength Atmospheric pressure: 500 Vrms/60Hz 70,000 ft.: 125 Vrms/60Hz

Negative Coil Transient (Vdc) 134D, 134DD 1.0 max

Diode P.I.V. (Vdc) 134D, 134DD 100 min.

BASE PART

NUMBERS

(See Note 8 for full P/N example)

134-5

134D-5

134DD-5

134-6

134D-6

134DD-6

134-9

134D-9

134DD-9

134-12

134D-12

134DD-12

134-18

134D-18

134DD-18

134-26

134D-26

134DD-26

Coil Voltage (Vdc) Nom. 5.0 6.0 9.0 12.0 18.0 26.5

Max. 7.5 10.0 15.0 20.0 30.0 40.0

Coil Resistance

(Ohms ±10% @25°C)

134, 134D 100 200 400 800 1600 3200

134DD (Note 4) 64 125 400 800 1600 3200

Coil Current (mAdc @25°C)

(134DD Series)

Min. 56.8 36.3 18.1 12.5 9.6 7.2

Max. 78.1 48.9 23.6 16.0 12.2 9.0

Pick-up Voltage (Vdc, Max.) 134, 134D 3.5 4.5 6.8 9.0 13.5 18.0

134DD 3.7 4.8 8.0 11.0 14.5 19.0

Drop-out Voltage (Vdc)

134, 134D Min. 0.12 0.18 0.35 0.41 0.59 0.89

Max. 2.5 3.2 4.9 6.5 10.0 13.0

134DD Min. 0.7 0.8 0.9 1.0 1.1 1.3

Max. 2.6 3.0 4.5 5.8 9.0 13.0

.01 0.5 .1 .5 1.0

FREQUENCY (GHz)

FIGURE 1

TYPICAL RF PERFORMANCE

INSERTION LOSS

RETURN LOSS (VSWR)

ISOLATION ACROSS CONTACTS

ISOLATION ACROSS POLES

1.92

1.22

1.07

1.02

1.01

1.00

VSWR

300

250

200

150

100

0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0

LOAD CURRENT (AMPS DC)

FIGURE 2

TYPICAL DC CONTACT RATING (RESISTIVE)

LOAD VOLTAGE (VDC)

www.teledynerelays.com 134/0704/Q1

ESTABLISHED RELIABILITY

CASE DETAIL

.375 (9.53)

SQ. MAX.

.335 (8.51)

SQ. MAX.

.375 (9.53) MAX.

DIMENSIONS ARE SHOWN IN INCHES (MILLIMETERS)

TERMINAL LOCATIONS

(Viewed from Terminals; Numbers for Reference Only)

.017 (.43) DIA.

+.002 (.05)

–.001 (.03)

WIRE LEAD .750 (19.05) MIN.

PIN: .187 (1.75) ±.010 (.25)

(See Note 5)

.031 ±.003

(.79 ±.08) .035 ±.010

(.89 ±.25)

.100 ±.010

(2.54 ±.25)

TYP 8 PLACES

OUTLINE DIMENSIONS

GENERAL NOTES

1. Relay contacts will exhibit no chatter in excess of 10 μsec or transfer in excess of 1 μsec.

2. “Typical” characteristics are based on available data and are best estimates. No on-going

verification tests are performed.

3. Unless otherwise specified, parameters are initial values.

4. For reference only. Coil resistance not directly measurable at relay terminals due to

internal series diode in 134DD only.

5. Unless otherwise specified, relays will be supplied with either gold-plated or solder-

coated leads.

6. The slash and characters appearing after the slash are not marked on the relay.

7. Screened HI-REL versions available. Contact factory.

SCHEMATIC DIAGRAMS

Teledyne Part Numbering System for T

Established Reliability Relay

ER 134 Z M4 - 26 A / S Q

Established Reliability

Designator

Pad Option

(See Appendix)

Relay Series

Ground Pin Option

(See Appendix)

Q= Solder-Coated Leads

G= Gold-Plated Leads

(Notes 5 and 6)

S= .187" leads

(Note 6)

Coil Voltage

Screening and Reliability

Level

Teledyne Part Numbering System for Military Qualified (JAN) Relays

J 134 Z M4 - 26 P L

Military (JAN)

Designator

Pad Option

(See Appendix)

Relay Series

Ground Pin Option

(See Appendix)

Terminal Variant

P = 0.187"

Coil Voltage

Screening and Reliability

Level

SCHEMATICS ARE VIEWED

FROM TERMINALS

134

134D

134DD

SERIES 134

Pad designation and

bottom view dimensions Height For use with the following: Dim. H

Max.

“M4” Pad for TO-5

ER411T

ER412, ER412D, ER412DD .295 (7.49)

712, 712D, 712TN,

RF300, RF310, RF320 .300 (7.62)

ER420, ER422D, ER420DD, 421,

ER421D, ER421DD, ER422, ER422D,

ER422DD, 722, 722D, RF341

.305 (7.75)

ER431T, ER432T,

ER432, ER432D, ER432DD .400 (10.16)

732, 732D, 732TN, RF303, RF313,

RF323 .410 (10.41)

RF312 .350 (8.89)

“M4” Pad for TO-5

ER411, ER411D, ER411DD .295 (7.49)

ER431, ER431D, ER431DD .400 (10.16)

RF311 .300 (7.62)

RF331 .410 (10.41)

“M4” Pad for Centigrid®

172, 172D .305 (7.75)

ER114, ER114D, ER114DD,

J114, J114D, J114DD .300 (7.62)

ER134, ER134D, ER134DD,

J134, J134D, J134DD .400 (10.16)

RF100 .315 (8.00)

RF103 .420 (10.67)

“M9” Pad for Centigrid®

122C, A152 .320 (8.13)

ER116C, J116C .300 (7.62)

ER136C, J136C .400 (10.16)

RF180 .325 (8.25)

A150 .305 (7.75)

Notes:

1. Spacer pad material: Polyester  lm.

2. To specify an “M4” or “M9” spacer pad, refer to the mounting variants portion of the part numbering

example in the applicable datasheet.

3. Dimensions are in inches (mm).

4. Unless otherwise speci ed, tolerance is ± .010 (.25).

5. Add 10 m to the contact resistance show in the datasheet.

6. Add 0.01 oz. (0.25 g) to the weight of the relay assembly shown in the datasheet.

Ø.150

[3.81]

(REF)

Dim H

MAX

Dim H

MAX

Dim H

MAX

.156

[3.96]

(REF)

.256

[6.5]

(REF)

Dim H

MAX

Appendix A: Spacer Pads

Pad designation and

bottom view dimensions Height For use with the following: Dim. H

Max.

“M” Pad 5/ 6/

ER411T, J411T, ER412, ER412D

ER412DD, J412, J412D, J412DD

ER412T, J412T

.388 (9.86)

712, 712D, 712TN .393 (9.99)

ER431T, J431T, ER432, ER432D

ER432DD, J432, J432D, J432DD

ER432T, J432T

.493 (12.52)

732, 732D, 732TN .503 (12.78)

ER420, J420, ER420D, J420D

ER420DD, J420DD, ER421, J421

ER421D, J421D, ER421DD

J422D, ER422DD, J422DD, 722

.398 (10.11)

“M2” Pad 7/ 8/

ER411T

ER412, ER412D, ER412DD

J412, J412D, J412DD

.441 (11.20)

712, 712D .451 (11.46)

ER421, ER421D, ER421DD

722, 732D .451 (11.46)

ER431T

ER432, ER432D, ER432DD .546 (13.87)

732, 732D .556 (14.12)

“M3” Pad 5/ 6/ 9/

ER411, ER411D, ER411DD

ER411TX

ER412X, ER412DX, ER412DDX

ER412TX

.388 (9.86)

712X, 712DX, 712TNX .393 (9.99)

ER420X, ER420DX, ER420DDX

ER421X, ER421DX, ER421DDX

ER422X, ER422DX

ER422DDX, 722X, 722DDX

.398 (10.11)

ER431, ER431D, ER431DD

ER431TX

ER432X, ER432DX, ER432DDX

ER432TX

.493 (12.52)

732X, 732DX, 732TNX .503 (12.78)

Notes:

1. Spreader pad material: Diallyl Phthalate.

2. To specify an “M”, “M2” or “M3” spreader pad, refer to the mounting variants portion of the part number example

in the applicable datasheet.

3. Dimensions are in inches (mm).

4. Unless otherwise speci ed, tolerance is ± .010” (0.25).

5/. Add 25 m to the contact resistance shown in the datasheet.

6/. Add .01 oz. (0.25 g) to the weight of the relay assembly shown in the datasheet.

7/. Add 50 m to the contact resistance shown in the datasheet.

8/. Add 0.025 oz (0.71 g) to the weight of the relay assembly shown in the datasheet.

9/. M3 pad to be used only when the relay has a center pin (e.g. ER411M3-12A, 722XM3-26.)

.370 [9.4]

MAX SQ

.150

[3.81]

.100

[2.54]

.200

[5.08]

.300

[7.62]

.100

[2.54]

Dim H

MAX

.370

[9.4]

MIN

.014

[0.36]

(REF)

.390 [9.91]

.300

[7.62]

.100

[2.54]

.300

[7.62]

.100

[2.54] .150

[3.81]

.150

[3.81]

.130

[3.3]

Dim H

MAX

.370 [9.4]

MAX SQ

.150

[3.81]

.100

[2.54]

.200

[5.08]

.300

[7.62]

.100

[2.54]

Dim H

MAX

.370

[9.4]

MIN

.014

[0.36]

(REF)

Appendix A: Spreader Pads

.100

[2.54]

.100

[2.54]

.100

[2.54]

"Y" POSITION

"Z" POSITION

.100

[2.54]

.100

[2.54]

.100

[2.54]

"W" POSITION

"U" POSITION

(ER116C and ER136C only)

"X" POSITION

"Z" POSITION

"Y" POSITION

.050

[1.27]

36°±3°

Ø.200

[Ø5.08]

"Z" POSITION

"Y" POSITION

"X" POSITION

45°±3°

"Z" POSITION

"Y" POSITION

Ø.200

[Ø5.08]

Centigrid® Relays:

RF100, RF103, ER114, ER134, 172

Centigrid® Relays:

RF180, ER116C, 122C, ER136C

TO-5 Relays:

ER411T, ER412, ER412T, ER420, ER421, ER422,

ER431T, ER432, ER432T, 712, 712TN, 400H, 400K,

400V, RF300, RF303, RF341, RF312, RF310, RF313,

RF320, RF323

TO-5 Relays:

ER411, ER431, RF311, RF331

NOTES

1. Terminal views shown

2. Dimensions are in inches (mm)

3. Tolerances: ± .010 (±.25) unless otherwise speci ed

4. Ground pin positions are within .015 (0.38) dia. of true position

5. Ground pin head dia., 0.035 (0.89) ref: height 0.010 (0.25) ref.

6. Lead dia. 0.017 (0.43) nom.

Indicates ground pin position

Indicates glass insulated lead position

Indicates ground pin or lead position

depending on relay type

Appendix A: Ground Pin Positions