www.stancor.com
PART NO. 37-6608B
Replaces 37-6608A
0837
TransGlobal®
TGC Series
International Transformer
Chassis Mount
ELECTROCUTION HAZARD
Disconnect electric power to system at
main fuse or circuit breaker box before
servicing. Failure to do so could result
in death or serious injury.
FIRE HAZARD
Do not exceed transformer ratings.
Higher voltage may damage control
and could cause personal injury or
property damage.
SPECIFICATIONS:
WARNING
!
INPUT:
OUTPUT:
INSULATION RATING:
DIELECTRIC STRENGTH:
AGENCY APPROVALS:
FILE NOs.:
115/230 VAC, 50/60 Hz
See Table
Class B (130˚ C)
4,000 VRMS
UL recognized component for use in
the US and Canada
TUV certified to EN61558
Designed to requirements of EN60950
UL File # E173993
TUV Report # DI 401341
STANCOR Secondary RMS Rating
PART Series Parallel Agency
NUMBER VA Volts Amps Volts Amps Certif.
TGC25-10 25 10.0 C.T. @ 2.50 5.0 @ 5.00 † ‡
TGC43-10 43 10.0 C.T. @ 4.30 5.0 @ 8.60 † ‡
TGC80-10 80 10.0 C.T. @ 8.00 5.0 @ 16.00 † ‡
TGC130-10 130 10.0 C.T. @ 13.00 5.0 @ 26.00 †
TGC175-10 175 10.0 C.T. @ 17.50 5.0 @ 35.00 †
TGC25-12 25 12.6 C.T. @ 2.00 6.3 @ 4.00 † ‡
TGC43-12 43 12.6 C.T. @ 3.40 6.3 @ 6.80 † ‡
TGC80-12 80 12.6 C.T. @ 6.30 6.3 @ 12.60 † ‡
TGC130-12 130 12.6 C.T. @ 10.30 6.3 @ 20.60 †
TGC175-12 175 12.6 C.T. @ 14.00 6.3 @ 28.00 †
TGC25-16 25 16.0 C.T. @ 1.60 8.0 @ 3.20 † ‡
TGC43-16 43 16.0 C.T. @ 2.70 8.0 @ 5.40 † ‡
TGC80-16 80 16.0 C.T. @ 5.00 8.0 @ 10.00 † ‡
TGC130-16 130 16.0 C.T. @ 8.10 8.0 @ 16.20 †
TGC175-16 175 16.0 C.T. @ 11.00 8.0 @ 22.00 †
TGC25-20 25 20.0 C.T. @ 1.25 10.0 @ 2.50 † ‡
TGC43-20 43 20.0 C.T. @ 2.20 10.0 @ 4.40 † ‡
TGC80-20 80 20.0 C.T. @ 4.00 10.0 @ 8.00 † ‡
TGC130-20 130 20.0 C.T. @ 6.50 10.0 @ 13.00 †
TGC175-20 175 20.0 C.T. @ 8.80 10.0 @ 17.60 †
Agency Certification : † ‡
STANCOR Secondary RMS Rating
PART Series Parallel Agency
NUMBER VA Volts Amps Volts Amps Certif.
TGC25-24 25 24.0 C.T. @ 1.00 12.0 @ 2.00 † ‡
TGC43-24 43 24.0 C.T. @ 1.80 12.0 @ 3.60 † ‡
TGC80-24 80 24.0 C.T. @ 3.30 12.0 @ 6.60 † ‡
TGC130-24 130 24.0 C.T. @ 5.40 12.0 @ 10.80 †
TGC175-24 175 24.0 C.T. @ 7.30 12.0 @ 14.60 †
TGC25-28 25 28.0 C.T. @ 0.90 14.0 @ 1.80 † ‡
TGC43-28 43 28.0 C.T. @ 1.50 14.0 @ 3.00 † ‡
TGC80-28 80 28.0 C.T. @ 2.80 14.0 @ 5.60 † ‡
TGC130-28 130 28.0 C.T. @ 4.60 14.0 @ 9.20 †
TGC175-28 175 28.0 C.T. @ 6.25 14.0 @ 12.50 †
TGC25-36 25 36.0 C.T. @ 0.70 18.0 @ 1.40 † ‡
TGC43-36 43 36.0 C.T. @ 1.20 18.0 @ 2.40 † ‡
TGC80-36 80 36.0 C.T. @ 2.20 18.0 @ 4.40 † ‡
TGC130-36 130 36.0 C.T. @ 3.60 18.0 @ 7.20 †
TGC175-36 175 36.0 C.T. @ 4.80 18.0 @ 9.60 †
TGC25-230 25 230.0 C.T. @ 0.11 115.0 @ 0.22 ‡
TGC43-230 43 230.0 C.T. @ 0.19 115.0 @ 0.38 ‡
TGC80-230 80 230.0 C.T. @ 0.35 115.0 @ 0.70 ‡
TGC130-230 130 230.0 C.T. @ 0.57 115.0 @ 1.14
TGC175-230 175 230.0 C.T. @ 0.76 115.0 @ 1.52
NOTES:
1. Designed for single input and single output use only
and requires simultaneous use of all windings. 2. The input to the transformer must be fused with an IEC
60127-2 Standard Sheet 3 Time lag (surge-proof)
Low-breaking capacity or Standard Sheet 6 Time lag
(surge-proof) Enhanced breaking capacity fuse. The
fuse value are shown in the Dimensions and Require-
ments Table
DIMENSIONS-INCHES INPUT FUSE
Weight
Mounting
Slots
Style H W D MW MD Series ParallelC Q.C. (lbs.)
S 2.38 2.81 1.94 2.38 - 0.156 x 0.250
0.187 x 0.281
0.218 x 0.312
0.218 x 0.312
0.187 x 0.375
.187 1.3
S 2.75 3.25 1.94 2.81 - 0.31
0.31
.187 1.8
NV 3.00 2.50 2.38 2.00 2.19 0.31 .187 2.9
NV 3.38 2.81 2.88 2.25 2.50 0.38 .250 4.5
NV 3.75 3.13 2.88 2.50
0.16A
0.315A
0.5A
1.0A
1.25A
0.315A
0.63A
1.0A
2.0A
2.5A2.50 0.38 .250 5.6
VA
25
43
80
130
175
TGC Series Dimensions and Requirements
MW W
Label “A” on
this surface
quick connect or
solder terminals
Term 1 ref.
Mtg Slots (2)
H
D
C
Style S
Schematic Diagram
Line Load
Load
Line
Primary: 115/230 V, 50/60 Hz
For 230 V:
connect 2 & 5
For 115 V:
connect 1 & 5, 2 & 6 Series: connect 8 & 11
Parallel: connect 7 & 11, 8 & 12
1
2
5
6
7
8
11
12
TGCXX-XX
PRI:
115/230V 50/60Hz
SEC:
SERIES:
XX.XVCT X.XA
PARALLEL:
X.XV X.XA
CHINA
12
11
8
7
6
5
2
1
PA41-XX-XX
Label “A” Detail
Label “A” on
this surface
Term 1 ref.
MW
W
Mtg. Slots (4)
quick connect or
solder terminals
MD
D
C
H
Style NV
