© Semiconductor Components Industries, LLC, 2011
April, 2011 − Rev. 3
1Publication Order Number:
CM6407/D
CM6407
EMI Filters with ESD
Protection for Data Line
Applications
Product Description
The CM6407 is an 18−bump EMI filter with ESD protection device
for data line application in a 0.4 mm pitch, 5 x 4 CSP form factor. It is
fully compliant with IEC 61000−4−2 Level 4. The CM6407 is
RoHS II compliant.
Features
•18−Bump, 1.96 mm X 1.56 mm Footprint Chip Scale Package
•These Devices are Pb−Free and are RoHS Compliant
MARKING DIAGRAM
Device Package Shipping†
ORDERING INFORMATION
http://onsemi.com
CSP−18
(Pb−Free)
5000/Tape & ReelCM6407
6407 = CM6407
YYWW = Date Code
XXXX = Last four digits of lot#
WLCSP18
CASE 567CG
†For information on tape and reel specifications,
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specification
Brochure, BRD8011/D.
ELECTRICAL SCHEMATIC
6407
YYWW
XXXX
R
Bottom Zener
(Common to all Channels)
+
I/O (1:7) LI/O (1:7)
CM6407
http://onsemi.com
2
PACKAGE / PINOUT DIAGRAMS
Bottom View
(Bumps Up View)
Top View
(Bumps Down View)
+
Orientation
Marking
A1 Corner
Indicator
6407
Table 1. PIN DESCRIPTIONS
A5 = Line 1 A4 = Line 2 A3 = GND A2 = Line 1 A1 = Line 2
B5 = Line 3 B3 = GND B1 = Line 3
C5 = Line 4 C4 = Line 5 C3 = GND C2 = Line 4 C1 = Line 5
D5 = Line 6 D4 = Line 7 D3 = GND D2 = Line 6 D1 = Line 7
ELECTRICAL SPECIFICATIONS AND CONDITIONS
Table 2. PARAMETERS AND OPERATING CONDITIONS
Parameter Rating Units
Storage Temperature Range –55 to +150 °C
Operating Temperature Range –40 to +85 °C
Power Dissipation at 70°C per Channel 60 mW
Table 3. ELECTRICAL OPERATING CHARACTERISTICS (Note 1)
Symbol Parameter Conditions Min Typ Max Units
R Resistance 100 125 150 W
L Inductance (Note 2) 35 nH
CCapacitance per Channel At 1 MHz, VIN = 0 V 19 24 29 pF
At 1 MHz, VIN = 2.5 V 15 pF
Att(5) Passband Attenuation at 5 MHz −7 dB
FCCut−off Frequency ZSOURCE = 50 W, ZLOAD = 50 W250 MHz
VBR Breakdown Voltage IR = ±1 mA ±6±7.8 ±10 V
ILEAK Leakage Current per Channel VIN = 3.0 V 10 100 nA
VESD ESD Peak Discharge Voltage Protection at All Pins:
a) Contact Discharge per IEC 61000−4−2
standard
b) Air Discharge per IEC 61000−4−2 standard
(Note 2)
±15
±15
kV
1. All parameters specified at TA = 25°C unless otherwise noted.
2. Standard IEC 61000−4−2 (CDischarge = 150 pF, RDischarge = 330 W).
CM6407
http://onsemi.com
3
RF CHARACTERISTICS
Figure 1. Typical Insertion Loss (Bias = 0 V, TA = 255C, 50 W Environment)
CM6407
http://onsemi.com
4
PACKAGE DIMENSIONS
WLCSP18, 1.96x1.56
CASE 567CG−01
ISSUE O
SEATING
PLANE
0.05 C
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. COPLANARITY APPLIES TO SPHERICAL
CROWNS OF SOLDER BALLS.
2X
DIM
A
MIN MAX
0.57
MILLIMETERS
A1
D1.96 BSC
E
b0.24 0.29
e0.40 BSC
0.63
È
È
D
E
AB
PIN A1
REFERENCE
e
A0.05 BC
0.03 C
0.05 C
18 b
45
C
B
A
0.05 C
A
A1
A2
C
0.17 0.24
1.56 BSC
0.25
18X
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
SOLDERING FOOTPRINT*
0.40
0.40
0.05 C
2X TOP VIEW
SIDE VIEW
BOTTOM VIEW
NOTE 3
e
A2 0.41 REF
RECOMMENDED
PACKAGE
OUTLINE
123
PITCH
DPITCH
A1
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
CM6407/D
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
