Standard Proximity Sensor E2E Additions to the Series Standard Sensors for Detecting Ferrous Metals under Standard Conditions Wide array of variations. Ideal for a variety of applications. Lineup includes models with pre-wired connectors that use highly oil-resistant cables Lineup includes models with 3-mm diameter and sensing distance of 0.6 mm Cable protector provided as a standard feature. Sensing surface made from material that resists cutting oil for superior environment resistance. Be sure to read Safety Precautions on page 22. Cylindrical Proximity Sensor Selection Guide Size Shield- Diameter ing 3 dia. 4 dia. M5 5.4 dia. M8 M12 M18 M30 M8 Unshielded Long sensing distance Sensing distance Diameter Shielded Resists the influence of surrounding metal Determine the size based on the installation space. M12 M18 M30 Power supply The sensing distance depends on the diameter, shielding, and type of power supply. Sensing distance (mm) 0.6 0.8 1.0 1.5 2 3 4 5 7 8 10 14 18 20 DC 3-wire DC 3-wire DC 3-wire DC 3-wire DC 3-wire AC 2-wire DC 2-wire DC 3-wire AC 2-wire DC 2-wire AC/DC 2-wire DC 3-wire AC 2-wire DC 2-wire AC/DC 2-wire DC 3-wire AC 2-wire DC 2-wire AC/DC 2-wire DC 3-wire AC 2-wire DC 2-wire DC 3-wire AC 2-wire DC 2-wire DC 3-wire AC 2-wire DC 2-wire DC 3-wire AC 2-wire DC 2-wire 1 E2E DC *Check interface conditions for load. Power/Output Yes DC 2-wire power? DC 2-Wire Models E2E-X@D@ No DC 3-Wire Models E2E-X@E@ AC 2-Wire Models E2E-X@Y@ AC AC/DC 2-Wire Models E2E-X@T1 AC/DC Environment -40 to 85C E2E-X@E@ E2E-X@Y@ Wide operating temperature range -25 to 70C E2E-X@D@ E2E-X@T1 Resists the influence of surrounding metal Maintenance Reducing stocked models NPN/PNP output AC/DC Shielded Models DC 2-Wire Models E2E-X@D@ AC/DC 2-Wire Models E2E-X@T1 Connector Models E2E-X@D@-M1(G) E2E-X@E@-M1 E2E-X@Y@-M1 Easy replacement Pre-wired Connector Models E2E-X@D1-M1(G)J(-T) Smartclick Pre-wired Connector Models E2E-X@D@-M1TGJ-U Reducing troubles Models with Highly Oil-resistant Cables E2E-X@D@-U Higher oil resistance PUR (polyurethane) cable Mounting to moving parts Robotics Cable Models E2E-X@D1-R E2E-X@E1-R Robotics cable Mutual interference prevention Miswiring measures Early discovery of problems Models with a different frequency (NO Models only) E2E-X@@15 Load short-circuit protection DC 2-Wire Models E2E-X@D@ DC 3-Wire Models E2E-X@E@ No polarity DC 2-Wire No-polarity Models E2E-X@D1-M1J-T Diagnostic Models E2E-X@D1S Note: Ask your OMRON sales representative for detail on Long Body Models, Transmission Couplers, and Power Couplers. 2 E2E Features Additions to the Series Proximity Sensors with Highly Oil-resistant Cables added to the lineup with the E2E-@-U Oil Resistance (Insulation service life): twice or three times that of oil-resistant vinyl chloride Cable Flexibility at Low Temperatures Cable Flexibility Oil Resistance Cable Flexibility: approximately twice that of cinyl chloride cables More Flexibility at -40C Models with Smartclick pre-wired connectors added to the E2E-@-U Series XS5 Smartclick connectors used to enable checking connector mating Jacket: Polyester elastomer Insulation: Oil-resistant grade PUR (polyurethane) Differentiation from standard models: Orange Head * The dimensions are the same as for standard models. Ordering Information Sensors Higher Oil Resistance, DC 2-Wire, Pre-wired Models Appearance Shielded M8 M12 M18 M30 Model Sensing distance NO NC 2 mm E2E-X2D1-U E2E-X2D2-U 3 mm E2E-X3D1-U E2E-X3D2-U E2E-X7D1-U E2E-X7D2-U E2E-X10D1-U E2E-X10D2-U 7 mm 10 mm Higher Oil Resistance, DC 2-Wire, M12 Smartclick Pre-wired Models Appearance Shielded Sensing distance Model NO NC M8 2 mm E2E-X2D1-M1TGJ-U E2E-X2D2-M1TGJ-U M12 3 mm E2E-X3D1-M1TGJ-U E2E-X3D2-M1TGJ-U E2E-X7D1-M1TGJ-U E2E-X7D2-M1TGJ-U E2E-X10D1-M1TGJ-U E2E-X10D2-M1TGJ-U M18 M30 7 mm 10 mm 3 E2E DC 2-Wire, Pre-wired Models (Models with self-diagnostic function are 3-wire.) Self-diagnostic output Appearance Shielded M12 3 mm M18 7 mm M30 Yes Unshielded 10 mm M12 8 mm M18 14 mm M30 Shielded M8 M12 20 mm M8 NC E2E-X3D1S *1 --- E2E-X7D1S *1 --- E2E-X10D1S *1 --- E2E-X8MD1S *1 --- E2E-X14MD1S *1 --- E2E-X20MD1S *1 --- 2 mm E2E-X2D2-N *3 3 mm E2E-X3D1-N *1*2*3 E2E-X3D2-N *3 7 mm M30 Unshielded NO E2E-X2D1-N *2*3 M18 None Model Sensing distance 10 mm 4 mm M12 8 mm M18 14 mm M30 20 mm E2E-X7D1-N *1*2*3 E2E-X7D2-N *3 E2E-X10D1-N *1*2*3 E2E-X10D2-N E2E-X4MD1 *2*3 E2E-X4MD2 E2E-X8MD1 *1*2*3 E2E-X8MD2 E2E-X14MD1 *1*2*3 E2E-X14MD2 E2E-X20MD1 *1*2*3 E2E-X20MD2 *1. Models with different frequencies are also available. The model numbers are E2E-X @D15 (example: E2E-X3D15-N). *2. Models with robotics cables are also available. Add "-R" to the end of the model number (example: E2E-X4MD1-R). The model number E2E-X2D1-N, however, becomes E2E-X2D1-R. *3. Models are also available with 5-m cables. Add the cable length to the model number (example: E2E-X3D1-N 5M). DC 2-Wire, Connector Models (Models with self-diagnostic function are 3-wire.) Connector Self-diagnostic output Appearance Shielded M12 M18 M30 Yes Unshielded M12 Sensing distance 3 mm 7 mm 10 mm 8 mm M18 14 mm M30 M12 Shielded 20 mm NC Applicable connector code *2 E2E-X3D1S-M1 D --- --- E2E-X7D1S-M1 D --- --- E2E-X10D1S-M1 D --- --- E2E-X8MD1S-M1 D --- --- E2E-X14MD1S-M1 D --- --- E2E-X20MD1S-M1 D --- --- M8 2 mm E2E-X2D1-M1G A E2E-X2D2-M1G D M12 3 mm E2E-X3D1-M1G *1 A E2E-X3D2-M1G D E2E-X7D1-M1G *1 A E2E-X7D2-M1G D E2E-X10D1-M1G *1 A E2E-X10D2-M1G D E2E-X4MD1-M1G A E2E-X4MD2-M1G D E2E-X8MD1-M1G *1 A E2E-X8MD2-M1G D E2E-X14MD1-M1G *1 A E2E-X14MD2-M1G D E2E-X20MD1-M1G *1 A E2E-X20MD2-M1G D E2E-X2D1-M3G G E2E-X2D2-M3G G E2E-X4MD1-M3G G E2E-X4MD2-M3G G M18 M30 M8 Unshielded M12 7 mm 10 mm 4 mm 8 mm M18 None NO Model Applicable connector code *2 14 mm M30 20 mm Shielded 2 mm M8 M8 Unshielded 4 mm *1. Models with different frequencies are also available. The model numbers are E2E-X@D15-M1G (example: E2E-X3D15-M1G). *2. Refer to page 19 for details. 4 E2E DC 2-Wire, Pre-wired Connector Models Appearance Shielded Sensing distance M12 M18 M30 Unshielded M12 Operate Mode 3 mm 7 mm 10 mm NO 8 mm M18 14 mm M30 20 mm Model Applicable Polarity: None connector code * Polarity: Yes Applicable connector code * E2E-X3D1-M1GJ A E2E-X3D1-M1J-T B E2E-X7D1-M1GJ A E2E-X7D1-M1J-T B E2E-X10D1-M1J-T E2E-X10D1-M1GJ A E2E-X8MD1-M1GJ A --- --- B E2E-X14MD1-M1GJ A --- --- E2E-X20MD1-M1GJ A --- --- Note: 1. A model with no polarity has a residual voltage of 5 V, which must be taken into consideration together with the interface conditions (the PLC's ON voltage, for example) when connecting the Proximity Sensor to a load. Refer to page 19 for details. 2. The standard cable length is 300 mm. Models are also available with 500 mm and 1 m cables. * Refer to page 19 for details. Connector Pin Assignments of DC 2-Wire Models * The connector pin assignments of each New E2E DC 2-Wire Model conform to IEC 947-5-2 Table III. (Only DC 2-Wire Models have been changed in comparison to the previous models.) * The following models with conventional connector pin assignments are available as well. (Only NO Models can be used.) The cable at the right should also be used if the XW3A-P@45-G11 Connector Junction Box is already being used. Cable length 500 mm Model XS2W-D421-BY1 Internal Wiring (Proximity Sensor end) (Wired end) 1 4 4 3 Models with conventional connector pin assignments are available as well. Appearance Shielded Unshielded NO Model Applicable connector code * NC Applicable connector code * M8 E2E-X2D1-M1 C E2E-X2D2-M1 D M12 E2E-X3D1-M1 C E2E-X3D2-M1 D M18 E2E-X7D1-M1 C E2E-X7D2-M1 D M30 E2E-X10D1-M1 C E2E-X10D2-M1 D M8 E2E-X4MD1-M1 C E2E-X4MD2-M1 D M12 E2E-X8MD1-M1 C E2E-X8MD2-M1 D M18 E2E-X14MD1-M1 C E2E-X14MD2-M1 D M30 E2E-X20MD1-M1 C E2E-X20MD2-M1 D Note: Refer to page 19 for details. 5 E2E DC 3-Wire, Pre-Wired Models Appearance Shielded Model Sensing distance Output configuration: NPN NO Output configuration: PNP NO 3 dia. 0.6 mm E2E-CR6C1 E2E-CR6B1 4 dia. 0.8 mm E2E-CR8C1 *1*2 E2E-CR8B1 *2 M5 1 mm E2E-X1C1 *1*2 E2E-X1B1 *2 5.4 dia. 1 mm E2E-C1C1 *1*2 E2E-C1B1 M8 1.5 mm E2E-X1R5E1 *1*2 E2E-X1R5F1 *1*2 M12 2 mm M18 5 mm M30 10 mm M8 2 mm Unshielded M12 5 mm M18 10 mm M30 18 mm E2E-X2E1 *1*2*3*4 E2E-X2F1 *1*2*3 E2E-X5E1 *1*2*3*4 E2E-X5F1 *1*2*3 E2E-X10E1 *1*2*3*4 E2E-X10F1 *2 E2E-X2ME1 *2 E2E-X2MF1 *2 E2E-X5ME1 *1*2*3*4 E2E-X5MF1 *2 E2E-X10ME1 *1*2*3*4 E2E-X10MF1 *2 E2E-X18ME1 *1*2*3*4 E2E-X18MF1 *2 Note: Models with NPN NC output configurations are also available for all of the above models. *1. Models are also available with 5-m cables. Add the cable length to the model number (example: E2E-X2E1 5M). *2. Models with robotics cables are also available. The model numbers are E2E-X @E1-R (example: E2E-X5E1-R). *3. Models with different frequencies are also available. The model numbers are E2E-X @E@5 (example: E2E-X5E15). *4. These models are also available with e-CON connectors (0.3-m cable). Add "-ECON" to the end of the model number (example: E2E-X2E1-ECON). DC 3-Wire, Connector Models Connector Appearance Shielded Sensing distance M8 1.5 mm M12 2 mm M18 5 mm M30 M12 M8 Unshielded M12 10 mm 2 mm Model Applicable connector Output configuration: Output configuration: code * NPN NO PNP NO E2E-X1R5E1-M1 E2E-X1R5F1-M1 B E2E-X2E1-M1 E2E-X2F1-M1 B E2E-X5E1-M1 E2E-X5F1-M1 B E2E-X10E1-M1 E2E-X10F1-M1 B E2E-X2ME1-M1 E2E-X2MF1-M1 B E2E-X5ME1-M1 E2E-X5MF1-M1 B E2E-X10ME1-M1 E2E-X10MF1-M1 B E2E-X18ME1-M1 E2E-X18MF1-M1 B 1.5 mm E2E-X1R5E1-M3 E2E-X1R5F1-M3 G 2 mm E2E-X2ME1-M3 E2E-X2MF1-M3 G 5 mm M18 10 mm M30 18 mm Shielded M8 M8 Unshielded Note: Models with NPN NC output configurations are also available for all of the above models. * Refer to page 19 for details. 6 E2E AC 2-Wire, Pre-wired Models Appearance Shielded M8 1.5 mm M12 2 mm M18 10 mm M8 2 mm M12 5 mm M18 NO NC E2E-X1R5Y1 5 mm M30 Unshielded Model Sensing distance 10 mm M30 18 mm E2E-X1R5Y2 E2E-X2Y1 *1*2 E2E-X2Y2 E2E-X5Y1 *1*2 E2E-X5Y2 E2E-X10Y1 *1*2 E2E-X10Y2 E2E-X2MY1 E2E-X2MY2 E2E-X5MY1 *1*2 E2E-X5MY2 E2E-X10MY1 *1 E2E-X10MY2 E2E-X18MY1 *1 E2E-X18MY2 *1. Models with different frequencies are also available. The model numbers are E2E-X @Y@5 (example: E2E-X5Y15). *2. Models are also available with 5-m cables. Add the cable length to the model number (example: E2E-X2Y1 5M). AC 2-wire, Connector Models Model Connector Appearance M12 Shielded Sensing distance 2 mm M18 5 mm M30 M12 Unshielded 10 mm M12 5 mm M18 10 mm M30 18 mm NO Applicable connector code * NC Applicable connector code * E2E-X2Y1-M1 E E2E-X2Y2-M1 F E2E-X5Y1-M1 E E2E-X5Y2-M1 F E2E-X10Y1-M1 E E2E-X10Y2-M1 F E2E-X5MY1-M1 E E2E-X5MY2-M1 F E2E-X10MY1-M1 E E2E-X10MY2-M1 F E2E-X18MY1-M1 E E2E-X18MY2-M1 F * Refer to page 19 for details. AC/DC 2-Wire, Pre-wired Models Appearance Shielded Sensing distance M12 M18 M30 Operation mode 7 mm 10 mm Model E2E-X3T1 3 mm NO E2E-X7T1 * E2E-X10T1 Note: These models do not conform to CE standards. * Models are also available with 5-m cables. Add the cable length to the model number (example: E2E-X7T1 5M). Accessories (Order Separately) Sensor I/O Connectors Refer to Introduction to Sensor I/O Connectors for details. Mounting Brackets Protective Covers Sputter Protective Covers Refer to Y92@ for details. 7 E2E Ratings and Specifications E2E-X@D@ DC 2-Wire Models Size Shielded Item M8 Shielded M12 Unshielded Model E2E-X2D@ Shielded M18 Unshielded Shielded M30 Unshielded Shielded Unshielded E2E-X4MD@ E2E-X3D@ E2E-X8MD@ E2E-X7D@ E2E-X14MD@ E2E-X10D@ E2E-X20MD@ Sensing distance 2 mm 10% 4 mm 10% 3 mm 10% 8 mm 10% 7 mm 10% 14 mm 10% 10 mm 10% 20 mm 10% Set distance *1 0 to 1.6 mm 0 to 3.2 mm 0 to 2.4 mm 0 to 6.4 mm 0 to 5.6 mm 0 to 11.2 mm 0 to 8 mm 0 to 16 mm Differential travel 15% max. of sensing distance Detectable object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on pages 13 and 14. Standard sensing object Iron, 8 x 8 x 1 mm Iron, Iron, Iron, Iron, 20 x 20 x 1 mm 12 x 12 x 1 mm 30 x 30 x 1 mm 18 x 18 x 1 mm Iron, 30 x 30 x 1 mm Iron, 54 x 54 x 1 mm Response frequency *2 1.5 kHz 1 kHz 0.1 kHz Power supply voltage (operating voltage range) 12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max. Leakage current 0.8 mA max. Control output 10% max. of sensing distance 0.8 kHz 0.5 kHz Load current 3 to 100 mA, Diagnostic output: 50 mA for -D1(5)S Models Residual voltage *3 3 V max. (Load current: 100 mA, Cable length: 2 m, M1J-T Models only: 5 V max.) 0.4 kHz Indicators D1 Models: Operation indicator (red) and setting indicator (green) D2 Models: Operation indicator (red) Operation mode (with sensing object approaching) D1 Models: NO D2 Models: NC Diagnostic output delay 0.3 to 1 s Protection circuits Surge suppressor, Load short-circuit protection (for control and diagnostic output) Ambient temperature range Operating: -25 to 70C, Storage: -40 to 85C (with no icing or condensation) Ambient humidity range Operating/storage: 35% to 95% (with no condensation) Temperature influence 15% max. of sensing distance at 23C in the temperature range of -25 to 70C Voltage influence 1% max. of sensing distance at rated voltage in the rated voltage 15% range Insulation resistance 50 M min. (at 500 VDC) between current-carrying parts and case Dielectric strength 1000 VAC, 50/60 Hz for 1 minute between current carry parts and case Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions Shock resistance Destruction: 500 m/s2 10 times each in X, Y, and Z directions Degree of protection Pre-wired Models : IEC 60529 IP67, in-house standards: oil-resistant Connector Models : IEC 60529 IP67 Connection method Pre-wired Models (Standard cable length: 2 m), Connector Models, or Pre-wired Connector Models (Standard cable length: 0.3 m) Pre-wired Models Weight Pre-wired (packConnector ed Models state) Connector Models Case Sensing surface MateriClamping als nuts Toothed washer Accessories Refer to the timing charts under I/O Circuit Diagrams on page 16 for details. Approx. 60 g 10% max. of sensing distance at 23C in the temperature range of -25 to 70C Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions Approx. 70 g Approx. 130 g Approx. 175 g Approx. 40 g Approx. 70 g Approx. 110 g Approx. 15 g Approx. 25 g Approx. 40 g Approx. 90 g Stainless steel (SUS303) Nickel-plated brass --- PBT Nickel-plated brass Zinc-plated iron Instruction manual *1. Use the E2E within the range in which the setting indicator (green LED) is ON (except D2 Models). *2. The response frequency is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and a set distance of half the sensing distance. *3. The residual voltage of each M1J-T Model is 5 V. When connecting to a device, make sure that the device can withstand the residual voltage. (Refer to page 23 for details.) 8 E2E E2E-X@E@/F@ DC 3-Wire Models Size Shielded M8 Shielded M12 Unshielded Shielded Shielded Unshielded E2E -X10ME@/F@ E2E-X10E@/ F@ E2E -X18ME@/F@ Sensing distance 1.5 mm 10% 2 mm 10% 5 mm 10% 10 mm 10% 18 mm 10% Set distance 0 to 1.2 mm 0 to 1.6 mm 0 to 4 mm 0 to 8 mm 0 to 14 mm Differential travel 10% max. of sensing distance Detectable object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on pages 13 and 14.) Standard sensing object Iron, 8 x 8 x 1 mm Iron, 12 x 12 x 1 mm Iron, 15 x15 x 1 mm Iron, 18 x 18 x 1 mm Iron, 30 x 30 x 1 mm Iron, 54 x 54 x 1 mm Response frequency *1 2 kHz 0.8 kHz 0.4 kHz 0.6 kHz 0.1 kHz Power supply voltage (operating voltage range) *2 12 to 24 VDC (10 to 40 VDC), ripple (p-p): 10% max. Current consumption 13 mA max. Control output Load current *2 200 mA max. Residual voltage 2 V max. (Load current: 200 mA, Cable length: 2 m) E2E -X5E@/F@ M30 Unshielded E2E -X2ME@/F@ 1.5 kHz E2E -X5ME@/F@ Shielded Model E2E -X1R5E@/F@ Item E2E -X2E@/F@ M18 Unshielded 0.2 kHz Indicators Operation indicator (red) Operation mode (with sensing object approaching) E1 Models: NO E2 Models: Refer to the timing charts under I/O Circuit Diagrams on page 16 for details. F1 Models: NO Protection circuits Load short-circuit protection, Surge suppressor, Reverse polarity protection Ambient temperature range *2 Operating/Storage: -40 to 85C (with no icing or condensation) Ambient humidity range Operating/Storage: 35% to 95% Temperature influence 15% max. of sensing distance at 23C in the temperature range of -40 to 85C 10% max. of sensing distance at 23C in the temperature range of -25 to 70C Voltage influence 1% max. of sensing distance at rated voltage in the rated voltage 15% range Insulation resistance 50 M min. (at 500 VDC) between current-carrying parts and case Dielectric strength 1,000 VAC, 50/60 Hz for 1 minute between current carry parts and case Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions Shock resistance Destruction: 500 m/s2 10 times each in X, Y, and Z directions Degree of protection Pre-wired Models : IEC 60529 IP67, in-house standards: oil-resistant Connector Models : IEC 60529 IP67 Connection method Pre-wired Models (Standard cable length: 2 m) and Connector Models Weight Materials Accessories 0.4 kHz Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions Prewired Models Approx. 65 g Approx. 75 g Approx. 150 g Approx. 195 g Connector Models Approx. 15 g Approx. 25 g Approx. 40 g Approx. 90 g Case Stainless steel (SUS303) Nickel-plated brass Sensing surface PBT Clamping nuts Nickel-plated brass Toothed washer Zinc-plated iron Instruction manual *1. The response frequency is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and a set distance of half the sensing distance. *2. When using an M8 Model at an ambient temperature between 70 and 85C, supply 10 to 30 VDC to the Sensor and make sure that the Sensor has a control output of 100 mA maximum. 9 E2E E2E-C@C/B@ and E2E-X1C/B@ DC 3-Wire Models Size 3 dia. 4 dia. E2E-CR6C/B@ E2E-CR8C/B@ Shielded Item M5 5.4 dia. E2E-X1C/B@ E2E-C1C/B@ Shielded Model Sensing distance 0.6 mm 15% 0.8 mm 15% 1 mm 15% Set distance 0 to 0.4 mm 0 to 0.5 mm 0 to 0.7 mm Differential travel 15% max. of sensing distance Detectable object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 14.) Standard sensing object Iron, 3 x 3 x 1 mm Iron, 5 x 5 x 1 mm Response frequency * 2 kHz 3 kHz Power supply voltage (operating voltage range) 12 to 24 VDC (10 to 30 VDC), ripple (p-p): 10% max. Current consumption 10 mA max. Control output 17 mA max. Load current Open-collector output, Open-collector output, 100 mA max. (30 VDC max.) 80 mA max. (30 VDC max.) Residual voltage 1 V max. (Load current: 80 mA, Cable length: 2 m) 2 V max. (Load current: 100 mA, Cable length: 2 m) Indicators Operation indicator (red) Operation mode (with sensing object approaching) C1/B1 Models: NO C2 Models: NC Protection circuits Reverse polarity protection, Surge suppressor Ambient temperature range Operating/Storage: -25 to 70C (with no icing or condensation) Ambient humidity range Operating/Storage: 35% to 95% Temperature influence 15% max. of sensing distance at 23C in the temperature range of -25 to 70C Voltage influence 5% max. of sensing distance at rated voltage in the 2.5% max. of sensing distance at rated voltage in the rated voltage 15% range rated voltage 10% range Insulation resistance 50 M min. (at 500 VDC) between current-carrying parts and case Dielectric strength 500 VAC, 50/60 Hz for 1 min between current-carrying parts and case Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions Shock resistance Destruction: 500 m/s2 10 times each in X, Y, and Z directions Degree of protection IEC 60529 IP66 Connection method Pre-wired Models (Standard cable length: 2 m) Weight (packed state) Approx. 60 g Materials Accessories Refer to the timing charts under I/O Circuit Diagrams on page 17 for details. IEC 60529 IP67, in-house standards: oil-resistant Case Stainless steel (SUS303) Sensing surface Heat-resistant ABS Clamping nuts Nickel-plated brass (E2E-X1C/B@ only) Toothed washer Zinc-plated iron (E2E-X1C/B@ only) Nickel-plated brass Instruction manual * The response frequency is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and a set distance of half the sensing distance. 10 E2E E2E-X@Y@ AC 2-Wire Models Size Shielded Item M8 Shielded Model E2E-X1R5Y@ M12 Unshielded E2E-X2MY@ Shielded E2E-X2Y@ M18 Unshielded E2E-X5MY@ Shielded E2E-X5Y@ M30 Unshielded Shielded Unshielded E2E-X10MY@ E2E-X10Y@ E2E-X18MY@ Sensing distance 1.5 mm 10% 2 mm 10% 5 mm 10% 10 mm 10% 18 mm 10% Set distance 0 to 1.2 mm 0 to 1.6 mm 0 to 4 mm 0 to 8 mm 0 to 14 mm Differential travel 10% max. of sensing distance Detectable object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 14.) Standard sensing object Iron, 8 x 8 x 1 mm Response frequency 25 Hz Power supply voltage (operating voltage range)*1 24 to 240 VAC (20 to 264 VAC), 50/60 Hz Leakage current 1.7 mA max. Control output Iron, 12 x 12 x 1 mm Load current *2 5 to 100 mA Residual voltage Refer to Engineering Data on page 15. Iron, Iron, 15 x 15 x 1 mm 18 x 18 x 1 mm Iron, 30 x 30 x 1 mm 5 to 200 mA 5 to 300 mA Indicators Operation indicator (red) Operation mode (with sensing object approaching) Y1 Models: NO Y2 Models: NC Protection circuits Surge suppressor Ambient temperature range *1*2 Operating/Storage: -25 to 70C (with no icing or condensation) Ambient humidity range Operating/storage: 35% to 95% (with no condensation) Temperature influence 10% max. of sensing distance at 23C in the temperature range of -25 to 70C Voltage influence 1% max. of sensing distance at rated voltage in the rated voltage 15% range Insulation resistance 50 M min. (at 500 VDC) between current-carrying parts and case Dielectric strength 4,000 VAC (M8 Models: 2,000 VAC), 50/60 Hz for 1 min between current-carrying parts and case Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions Shock resistance Destruction: 500 m/s2 10 times each in X, Y, and Z directions Degree of protection Pre-wired Models : IEC 60529 IP67, in-house standards: oil-resistant Connector Models : IEC 60529 IP67 Connection method Pre-wired Models (Standard cable length: 2 m) and Connector Models Weight Materials Accessories Iron, 54 x 54 x 1 mm Refer to the timing charts under I/O Circuit Diagrams on page 18 for details. Operating/Storage: -40 to 85C (with no icing or condensation) 15% max. of sensing distance at 23C in the temperature range of -40 to 85C, 10% max. of sensing distance at 23C in the temperature range of -25 to 70C Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions Prewired Models Model Approx. 60 g Approx. 70 g Approx. 130 g Approx. 175 g Connector Models Approx. 15 g Approx. 25 g Approx. 40 g Approx. 90 g Case Stainless steel (SUS303) Nickel-plated brass Sensing surface PBT Clamping nuts Nickel-plated brass Toothed washer Zinc-plated iron Instruction manual *1. When supplying 24 VAC to any of the above models, make sure that the operating ambient temperature range is at least -25C. *2. When using an M18 or M30 Connector Model at an ambient temperature between 70 and 85C, make sure that the Sensor has a control output (load current) of 5 to 200 mA max. 11 E2E AC/DC 2-Wire Models Size M12 M18 E2E-X3T1 E2E-X7T1 Shielded Item M30 Shielded Model E2E-X10T1 Sensing distance 3 mm 10% 7 mm 10% 10 mm 10% Set distance 0 to 2.4 mm 0 to 5.6 mm 0 to 8 mm Differential travel 10% max. of sensing distance Detectable object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering Data on page 13.) Iron, 12 x 12 x 1 mm Iron, 18 x 18 x 1 mm Iron, 30 x 30 x 1 mm DC 1 kHz 0.5 kHz 0.4 kHz AC 25 Hz Standard sensing object Response frequency *1 Power supply voltage 24 to 240 VDC (20 to 264 VDC) (operating voltage range) *2 48 to 240 VAC (40 to 264 VAC) Leakage current Control output DC: 1 mA max. AC: 2 mA max. Load current 5 to 100 mA Residual voltage DC: 6 V max. (Load current: 100 mA, Cable length: 2 m) AC: 10 V max. (Load current: 5 mA, Cable length: 2 m) Indicators Operation indicator (red), Setting indicator (green) Operation mode (with sensing object approaching) NO (Refer to the timing charts under I/O Circuit Diagrams on page 16 for details.) Protection circuits Load short-circuit protection (20 to 40 VDC only), Surge suppressor Ambient temperature range Operating: -25 to 70C, Storage: -40 to 85C (with no icing or condensation) Ambient humidity range Operating/Storage: 35% to 95% Temperature influence 10% max. of sensing distance at 23C in the temperature range of -25 to 70C Voltage influence 1% max. of sensing distance at rated voltage in the rated voltage 15% range Insulation resistance 50 M min. (at 500 VDC) between current-carrying parts and case Dielectric strength 4,000 VAC, 50/60 Hz for 1 minute between current-carrying parts and case Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions Shock resistance Destruction: 1,000 m/s2 10 times each in X, Y, and Z directions Degree of protection IEC 60529 IP67, in-house standards: oil-resistant Connection method Pre-wired Models (Standard cable length: 2 m) Weight (packed state) Materials Accessories Approx. 80 g Case Nickel-plated brass Sensing surface PBT Clamping nuts Nickel-plated brass Toothed washer Zinc-plated iron Approx. 140 g Approx. 190 g Instruction manual *1. The response frequency is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and a set distance of half the sensing distance. *2. Power Supply Voltage Waveform: Use a sine wave for the power supply. Using a rectangular AC power supply may result in faulty reset. 12 E2E I/O Circuit Diagrams E2E-X@D@ DC 2-Wire Models Operation mode Model Timing Chart Output circuit Polarity: Yes 1 E2E-X@D1-N E2E-X@D1-M1G(J) E2E-X@D1-(M1TGJ)-U E2E-X@D1-M3G Set position Unstable Non-sensing sensing area area Stable sensing area Proximity Sensor main circuit Proximity Sensor Sensing object Without selfdiagnostic output: NO Load Brown +V 4 0V Blue Note: The load can be connected to either the +V or 0 V side. 100 80 (%) 0 Rated sensing distance Polarity: None ON Setting indicator OFF (green) ON Operation OFF indicator (red) ON E2E-X@D1-M1J-T OFF Control output 4 Load Proximity Sensor main circuit +V (0 V) 3 0V (+V) Note 1. The load can be connected to either the +V or 0 V side. 2. The E2E-X@D1-M1J-T has no polarity. Therefore, terminals 3 and 4 have no polarity. Non-sensing area Sensing area Proximity Sensor Without selfdiagnostic output: NC Sensing object E2E-X@D2-N E2E-X@D2-M1G E2E-X@D2-(M1TGJ)-U E2E-X@D2-M3G 100 (%) Proximity Sensor main circuit 0 Rated sensing distance 1 ON OFF Unstable Non-sensing sensing area area E2E-X@D1S E2E-X@D1S-M1 0V Note: The load can be connected to either the +V or 0 V side. Control output Set position Stable sensing area Proximity Sensor Sensing object With selfdiagnostic output: NO +V 2 Blue ON Operation OFF indicator (red) (%) Load Brown Brown (4) 100 80 Rated sensing distance Load 0 ON Setting indicator OFF (green) ON OFF Operation indicator (red) ON OFF +V Load Orange (2) (diagnostic output) +V Blue (3) 0 Control output ON OFF Proximity Sensor main circuit Diagnostic output Note: Connect both the loads to the +V side of the control output and diagnostic output. The diagnostic output is ON when there is a coil burnout or the sensing object is located in the unstable sensing area for 0.3 s or longer. 16 E2E Sensor I/O Connectors Connector Screw Appearance Cable length 2m Straight 5m M12 2m L-shape 5m Smartclick Connector, Straight Straight Applicable connector code Connector model number A XS2F-D421-DA0-A B XS2F-D421-DC0-A C XS2F-D421-DD0 D XS2F-D421-D80-A E F XS2F-A421-DB0-A XS2F-A421-D90-A A XS2F-D421-GA0-A B XS2F-D421-GC0-A C XS2F-D421-GD0 D XS2F-D421-G80-A E F XS2F-A421-GB0-A XS2F-A421-G90-A A XS2F-D422-DA0-A B XS2F-D422-DC0-A C XS2F-D422-DD0 D XS2F-D422-D80-A E XS2F-A422-DB0-A A XS2F-D422-GA0-A B XS2F-D422-GC0-A C XS2F-D422-GD0 D XS2F-D422-G80-A E XS2F-A422-GB0-A 2m 1 3 9 2 7 6 E2E-X@D1S-M1 5 E2E-X@Y1-M1 E2E-X@Y2-M1 E2E-X@D1-M1G E2E-X@D1-M1GJ E2E-X@D1-M1J-T E2E-X@E/F1-M1 E2E-X@D1-M1 E2E-X@D2-M1 E2E-X@D2-M1(G) E2E-X@D1S-M1 E2E-X@Y1-M1 E2E-X@Y2-M1 E2E-X@D1-M1G E2E-X@D1-M1GJ E2E-X@D1-M1J-T E2E-X@E/F1-M1 E2E-X@D1-M1 E2E-X@D2-M1 E2E-X@D2-M1(G) E2E-X@D1S-M1 E2E-X@Y1-M1 E2E-X@D1-M1G E2E-X@D1-M1GJ E2E-X@D1-M1J-T E2E-X@E/F1-M1 E2E-X@D1-M1 E2E-X@D2-M1 E2E-X@D2-M1(G) E2E-X@D1S-M1 E2E-X@Y1-M1 11 12 E2E-X@D@-M1TGJ-U 5m XS5F-D421-G80-P 2m XS3F-M421-402-R 5m XS3F-M421-405-R G L-shape E2E-X@D1-M1G E2E-X@D1-M1GJ E2E-X@D1-M1J-T E2E-X@E/F1-M1 E2E-X@D1-M1 E2E-X@D2-M1 E2E-X@D2-M1(G) Connection diagram No. *1 1 3 9 2 7 6 5 11 12 1 3 9 2 7 6 5 11 1 3 9 2 7 6 5 11 XS5F-D421-D80-P H M8 *2 Applicable Proximity Sensor model number 2m XS3F-M422-402-R 5m XS3F-M422-405-R E2E-X@D1-M3G E2E-X@D2-M3G E2E-X@E/F1-M3 E2E-X@D1-M3G E2E-X@D2-M3G E2E-X@E/F1-M3 E2E-X@D1-M3G E2E-X@D2-M3G E2E-X@E/F1-M3 E2E-X@D1-M3G E2E-X@D2-M3G E2E-X@E/F1-M3 13, 14 4 8 10 4 8 10 4 8 10 4 8 10 *1. Refer to Connection Diagrams on page 20 for information on Proximity Sensor and I/O Connector connections. *2. Refer to Introduction to Sensor I/O Connectors for details and for information on Robotics Cables. 19 E2E Connections for Sensor I/O Connectors Type Operation mode Model Sensor I/O Connector model number 1: Straight 2: L-shape 1 DC 2-wire (IEC pin wiring) E2E-X@D1-M1G(J) XS2F-D42@-@A0-A D: 2-m cable G: 5-m cable 1: Straight 2: L-shape 2 DC 2-wire (previous pin wiring) E2E-X@D1-M1 XS2F-D42@-@D0 Connections E2E Main circuit Proximity Sensor D: 2-m cable G: 5-m cable 3 DC 2-wire (no polarity) NO E2E-X@D1-M1J-T XS2F-D42@-@C0-A D: 2-m cable G: 5-m cable 4 DC 2-wire (M8 connector) E2E-X@D1-M3G XS3F-M42@-40@-R 2: 2-m cable 5: 5-m cable 5 E2E-X@D1S-M1 XS2F-D42@-@80-A D: 2-m cable G: 5-m cable 6 DC 2-wire (IEC pin wiring) E2E-X@D2-M1G XS2F-D42@-@80-A D: 2-m cable G: 5-m cable 7 NC E2E-X@D2-M1 XS2F-D42@-@80-A D: 2-m cable G: 5-m cable 8 DC 2-wire (M8 connector) E2E-X@D2-M3G XS3F-M42@-40@-R 2: 2-m cable 5: 5-m cable Brown (+) Blue (-) XS2F 1 1 2 2 3 3 4 4 Blue (-) Brown (+) XS2F * 1 1 2 2 3 3 4 4 XS3F 1 1 2 2 3 3 4 4 Brown (not connected) Blue (+) (-) Black (-) (+) * Brown (+) White (not connected) Blue (not connected) Black (-) XS2F * 1 1 2 2 3 3 4 4 Brown (not connected) White (diagnostic output) (+) Blue (0 V) Black (control output) (+) XS2F * 1 1 2 2 3 3 4 4 Brown (+) White (-) Blue (not connected) Black (not connected) XS2F * 1 1 2 2 3 3 4 4 Brown (not connected) White (+) Blue (-) Black (not connected) XS3F * E2E Main circuit 1: Straight 2: L-shape 4 E2E Main circuit 1: Straight 2: L-shape DC 2-wire (previous pin wiring) 4 E2E Main circuit 1: Straight 2: L-shape 3 E2E Main circuit 1: Straight 2: L-shape DC 2-wire (diagnostic type) 2 3 E2E Main circuit 1: Straight 2: L-shape 1 2 E2E Main circuit 1: Straight 2: L-shape XS2F 1 E2E Main circuit Connection diagram No. 1 1 2 2 3 3 4 4 Brown (+) White (-) Blue (not connected) Black (not connected) * Different from Proximity Sensor wire colors. 20 E2E Operation mode Model Sensor I/O Connector model number 1: Straight 2: L-shape 9 DC 3-wire E2E-X@E/F1-M1 XS2F-D42@-@C0-A E2E D: 2-m cable G: 5-m cable NO 1: Straight 2: L-shape 10 Connections Main circuit Proximity Sensor Type DC 3-wire (M8 connector) E2E-X@E/F1-M3 XS3F-M42@-40@-R 2: 2-m cable 5: 5-m cable 11 NO E2E-X@Y1-M1 XS2F-A42@-@B0-A D: 2-m cable G: 5-m cable AC 2-wire 1 2 2 3 3 4 4 1 2 2 3 3 4 4 NC E2E-X@Y2-M1 D: 2-m cable G: 5-m cable Main circuit 12 1 1 2 2 3 3 4 4 E2E-X@D1M1TGJ-U NO D: 2-m cable G: 5-m cable Main circuit 13 XS5F-D421-@80-P 1 2 2 3 3 4 4 NC XS5F-D421-@80-P D: 2-m cable G: 5-m cable Main circuit 14 E2E-X@D2M1TGJ-U Brown Blue Brown White Blue (not connected) Black (not connected) XS5F 1 1 2 2 3 3 4 4 E2E-X@-M1TGJ DC 2-wire (Smartclick connector) Brown (+V) White (not connected) Blue (0 V) Black (output) XS2F * 1 E2E-X@-M1TGJ DC 2-wire (Smartclick connector) Blue (0 V) Black (output) XS2F E2E XS2F-A421-@90-A Brown (+V) XS3F 1 E2E Main circuit 1: Straight 2: L-shape XS2F 1 E2E Main circuit Connection diagram No. Brown (+) White (not connected) Blue (not connected) Black (-) XS5F 1 1 2 2 3 3 4 4 Brown (+) White (-) Blue (not connected) Black (not connected) * Different from Proximity Sensor wire colors. Refer to Introduction to Sensor I/O Connectors for details. 21 E2E Pre-wired Models (Shielded) Mounting Hole Dimensions Dimension F (mm) M5 5.5 +00.5 dia. M8 8.5 +0.5 dia. 0 M12 12.5 +0.5 dia. 0 F Diagram 4 E2E-X1@ Pre-wired Models (Unshielded) 25 17.5 15 9.7 dia. 8 * Operation indicator (red) Two clamping nuts Two toothed washers 4 M5 x 0.5 *2.9-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.14 mm2, Insulator diameter: 0.9 mm), Standard length: 2 m Robotics Cable Models: 2.9-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.15 mm2, Insulator diameter: 1.05 mm), Standard length: 2 m The cable can be extended up to 100 m (separate metal conduit). Diagram 5 E2E-X2D@ E2E-X1R5E@/F@ 15 dia. 26 13 3 8 7 26 13 Indicators *2 Two clamping nuts Toothed washer M8 x 1 E2E-X4MD@ E2E-X2ME@/F@ 30 7 30 15 dia. Diagram 6 6 3 8 6.1 dia. *1 Indicators *2 Two clamping nuts Toothed washer M8 x 1 *1 *1. 4-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.3 mm2, Insulator diameter: 1.3 mm), Standard length: 2 m 4-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.3 mm2, Insulator diameter: 1.3 mm), Standard length: 2 m Robotics Cable Models: 4-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.3 mm2, Insulator diameter: 1.27 mm), Standard length: 2 m 4-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.3 mm2, Insulator diameter: 1.27 mm), Standard length: 2 m Models with Highly Oil-resistant Cables: 4-dia. polyurethane-insulated round cable with 2 conductors (Conductor cross section: 0.3 mm2, Insulator diameter: 1.3 mm), Standard length: 2 m The cable can be extended up to 200 m (separate metal conduit). *2. D Models: Operation indicator (red) and setting indicator (green), E/F Models: Operation indicator (red) *1. 4-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.3 mm2, Insulator diameter: 1.3 mm), Standard length: 2 m 4-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.3 mm2, Insulator diameter: 1.3 mm), Standard length: 2 m Robotics Cable Models: 4-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.3 mm2, Insulator diameter: 1.27 mm), Standard length: 2 m 4-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.3 mm2, Insulator diameter: 1.27 mm), Standard length: 2 m The cable can be extended up to 200 m (separate metal conduit). *2. D Models: Operation indicator (red) and setting indicator (green), E/F Models: Operation indicator (red) Diagram 7 Diagram 8 E2E-X1R5Y@ 15 dia. 40 36 8 7 36 15 dia. 3 13 E2E-X2MY@ 7 40 13 6 8 3 6.1 dia. * Operation indicator (red) Two clamping nuts 4-dia. vinyl-insulated round cable with 2 conductors Toothed (Conductor cross section: 0.3 mm2, Insulator washer diameter: 1.3 mm), Standard length: 2 m The cable can be extended up to 200 m (separate metal conduit). M8 x 1 Diagram 9 Pre-wired e-CON Connector Models E2E-X3D@ E2E-X2E@/F@ 38 33 21 dia. 17 4 1 2 9 10 5.9 M8 x 1 * Operation indicator (red) Two clamping nuts 2 conductors Toothed 4-dia. vinyl-insulated round cable with (Conductor cross section: 0.3 mm2, Insulator diameter: washer 1.3 mm), Standard length: 2 m The cable can be extended up to 200 m (separate metal conduit). Diagram 10 E2E-X8MD@ Pre-wired e-CON Connector Models 5.9 1 E2E-X5ME@/F@ 2 15 3 4 15.6 Connector: Product code 37104-3163-000FL (Sumitomo 3M) 21 dia. 17 7 38 33 4 9 10 15 3 4 15.6 Connector: Product code 37104-3163-000FL (Sumitomo 3M) *1 M12 x 1 Indicators * 2 Two clamping nuts Toothed washer 9 dia. *1 2 *1. 4-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.3 mm , Insulator diameter: 1.3 mm), Standard length: 2 m 4-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.3 mm2, Insulator diameter: 1.3 mm), Standard length: 2 m Robotics Cable Models: 4-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.3 mm2, Insulator diameter: 1.27 mm), Standard length: 2 m 4-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.3 mm2, Insulator diameter: 1.27 mm), Standard length: 2 m Models with Highly Oil-resistant Cables: 4-dia. polyurethane-insulated round cable with 2 conductors (Conductor cross section: 0.3 mm2, Insulator diameter: 1.3 mm), Standard length: 2 m The cable can be extended (separate metal conduit) up to 200 m for the control output and up to 100 m for the diagnostic output. *2. D Models: Operation indicator (red) and setting indicator (green), E/F Models: Operation indicator (red) M12 x 1 Indicators *2 Two clamping nuts Toothed washer *1. 4-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.3 mm2, Insulator diameter: 1.3 mm), Standard length: 2 m 4-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.3 mm2, Insulator diameter: 1.3 mm), Standard length: 2 m Robotics Cable Models: 4-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.3 mm2, Insulator diameter: 1.27 mm), Standard length: 2 m 4-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.3 mm2, Insulator diameter: 1.27 mm), Standard length: 2 m The cable can be extended (separate metal conduit) up to 200 m for the control output and up to 100 m for the diagnostic output. *2. D Models: Operation indicator (red) and setting indicator (green), E/F Models: Operation indicator (red) 25 E2E Diagram 12 E2E-X5MY@ Diagram 11 E2E-X2Y@ 43 21 dia. 43 9 21 dia. 38 17 4 17 10 9 38 7 10 4 9 dia. * * Operation indicator (red) Two clamping nuts 4-dia. vinyl-insulated round cable with 2 Toothed conductors (Conductor cross section: 0.3 mm2, washer Insulator diameter: 1.3 mm), Standard length: 2 m The cable can be extended up to 200 m (separate metal conduit). M12 x 1 Operation indicator (red) Two clamping nuts Toothed 4-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.3 mm2, washer Insulator diameter: 1.3 mm), Standard length: 2 m The cable can be extended up to 200 m (separate metal conduit). M12 x 1 Pre-wired Models (Shielded) Mounting Hole Dimensions Dimension F (mm) M8 M12 M18 M30 8.5 +00.5 dia. 12.5 +00.5 dia. 18.5 +00.5 dia. 30.5 +00.5 dia. F Diagram 13 E2E-X3T1 Pre-wired Models (Unshielded) 60 21 dia. 9 55 17 4 10 *1 M12 x 1 Indicators *2 Two clamping nuts *1 4-dia. vinyl-insulated round cable with 2 Toothed conductors (Conductor cross section: 0.3 mm2, washer Insulator diameter: 1.3 mm), Standard length: 2 m The cable can be extended up to 200 m (separate metal conduit). *2 Operation indicator (red), Setting indicator (green) Diagram 15 E2E-X14MD@/E2E-X10ME@/F@ E2E-X10MY@ Pre-wired e-CON Diagram 14 E2E-X7D@/E2E-X5E@/F@ E2E-X5Y@/E2E-X7T1 Pre-wired e-CON Connector Models 43 29 dia. 12 38 4 24 10 1 2 Connector Models 5.9 3 4 15.6 Connector: Product code 37104-2206-000FL (Sumitomo 3M) 15 43 29 dia. 12 38 24 10 4 10 1 2 5.9 3 4 15.6 Connector: Product code 37104-2206-000FL (Sumitomo 3M) 15 14.8 dia. *1 M18 x 1 Indicators *2 Two clamping nuts Toothed washer *1. 6-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m 6-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m Robotics Cable Models: 6-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.5 mm2, Insulator diameter: 1.74 mm), Standard length: 2 m 6-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.5 mm2, Insulator diameter: 1.74 mm), Standard length: 2 m Models with Highly Oil-resistant Cables: 6-dia. polyurethane-insulated round cable with 2 conductors (Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m The cable can be extended (separate metal conduit) up to 200 m for the control output and up to 100 m for the diagnostic output. *2. D/T Models: Operation indicator (red), Setting indicator (green) E/F/Y Models: Operation indicator (red) M18 x 1 *1 Indicators *2 *1 Two clamping nuts Toothed washer *1. 6-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m 6-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m Robotics Cable Models: 6-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.5 mm2, Insulator diameter: 1.74 mm), Standard length: 2 m 6-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.5 mm2, Insulator diameter: 1.74 mm), Standard length: 2 m The cable can be extended (separate metal conduit) up to 200 m for the control output and up to 100 m for the diagnostic output. *2. D/T Models: Operation indicator (red), Setting indicator (green) E/F/Y Models: Operation indicator (red) 26 E2E Diagram 16 E2E-X10D@/E2E-X10E@/F@ E2E-X10Y@/E2E-X10T1 Diagram 17 E2E-X20MD@/E2E-X18ME@/F@ Pre-wired e-CON E2E-X18MY@ Pre-wired e-CON Connector Models Connector Models 1 2 5.9 3 48 43 42 dia. 36 4 15.6 Connector: Product code 37104-2206-000FL (Sumitomo 3M) 12 10 5 15 48 12 43 42 dia. 13 36 5 1 2 5.9 3 4 15.6 Connector: Product code 37104-2206-000FL (Sumitomo 3M) 15 10 26.8 dia. *1 *1 Indicators *2 M30 x 1.5 Two clamping nuts Toothed washer *1. 6-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m 6-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m Robotics Cable Models: 6-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.5 mm2, Insulator diameter: 1.74 mm), Standard length: 2 m 6-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.5 mm2, Insulator diameter: 1.74 mm), Standard length: 2 m Models with Highly Oil-resistant: 6-dia. polyurethane-insulated round cable with 2 conductors (Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m The cable can be extended (separate metal conduit) up to 200 m for the control output and up to 100 m for the diagnostic output. *2. D/T Models: Operation indicator (red), Setting indicator (green) E/F/Y Models: Operation indicator (red) Indicators *2 M30 x 1.5 Two clamping nuts Toothed washer *1. 6-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m 6-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.5 mm2, Insulator diameter: 1.9 mm), Standard length: 2 m Robotics Cable Models: 6-dia. vinyl-insulated round cable with 2 conductors (Conductor cross section: 0.5 mm2, Insulator diameter: 1.74 mm), Standard length: 2 m 6-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.5 mm2, Insulator diameter: 1.74 mm), Standard length: 2 m The cable can be extended (separate metal conduit) up to 200 m for the control output and up to 100 m for the diagnostic output. *2. D/T Models: Operation indicator (red), Setting indicator (green) E/F/Y Models: Operation indicator (red) M8 Connector Models (Shielded) M8 Connector Models (Unshielded) Diagram 28 E2E-X2D@-M3G/E2E-X1R5E1-M3/F@ Diagram 29 E2E-X4MD@-M3G/E2E-X2ME1-M3/F@ 39 31 39 31 15 dia. 15 dia. 26 8 3 13 * D Models: M8 x 1 26 6 13 M8 x 1 Indicators* Two clamping nuts Toothed washer Operation indicator (red), Setting indicator (green) E/F Models: Operation indicator (red) 8 3 6.1 dia. * D Models: Operation indicator (red), Setting Indicators* indicator (green) Two clamping nuts E/F Models: Operation indicator Toothed washer (red) M8 x 1 M12 Connector Models (Shielded) M12 Connector Models (Unshielded) Diagram 18 E2E-X2D@-M1(G) E2E-X1R5E1-M1/F@ Diagram 19 E2E-X4MD@-M1(G) E2E-X2ME1-M1/F@ 43 43 30 15 dia. 30 15 dia. 26 26 3 13 8 M8 x 1 M12 x 1 6 13 3 8 M12 x 1 6.1 dia. M8 x 1 * D Models: Indicators* Two clamping nuts Toothed washer Operation indicator (red), Setting indicator (green) E/F Models: Operation indicator (red) M8 x 1 Indicators* Two clamping nuts Toothed washer * D Models: Operation indicator (red), Setting indicator (green) E/F Models: Operation indicator (red) 27 E2E Diagram 20 E2E-X3D@-M1(G) E2E-X2E1-M1/F@ Diagram 21 E2E-X8MD@-M1(G) E2E-X5ME1-M1/F@ 48 48 21 dia. 21 dia. 33 4 17 10 M12 x 1 33 7 17 M12 x 1 10 4 9 dia. Indicators * Two clamping nuts Toothed washer M12 x 1 * D Models: Operation indicator (red), Setting indicator (green) E/F Models: Operation indicator (red) Indicators* Two clamping nuts Toothed washer M12 x 1 * D Models: Operation indicator (red), Setting indicator (green) E/F Models: Operation indicator (red) Diagram 23 E2E-X5MY@-M1 Diagram 22 E2E-X2Y@-M1 53 53 21 dia. 21 dia. 38 4 17 10 M12 x 1 38 7 17 M12 x 1 10 4 9 dia. Operation indicator (red) Two clamping nuts Toothed washer M12 x 1 Diagram 24 E2E-X7D@-M1(G)/E2E-X5E1-M1 E2E-X5Y@-M1 Operation indicator (red) Two clamping nuts Toothed washer M12 x 1 Diagram 25 E2E-X14MD@-M1(G)/E2E-X10ME1-M1 E2E-X10MY@-M1 53 53 29 dia. 4 24 38 29 dia. 38 10 10 24 10 4 M12 x 1 M12 x 1 14.8 dia. Indicators* Indicators* M18 x 1 M18 x 1 Two clamping nuts Toothed washer Two clamping nuts Toothed washer * D Models: Operation indicator (red), Setting indicator (green) E/Y Models: Operation indicator (red) * D Models: Operation indicator (red), Setting indicator (green) E/Y Models: Operation indicator (red) Diagram 26 E2E-X10D@-M1(G)/E2E-X10E1-M1 E2E-X10Y@-M1 Diagram 27 E2E-X20MD@-M1(G)/E2E-X18ME1-M1 E2E-X18MY@-M1 58 42 dia. 58 42 dia. 43 10 5 36 43 13 36 5 10 26.8 dia. M12 x 1 Indicators* M30 x 1.5 Two clamping nuts M12 x 1 Indicators* M30 x 1.5 Toothed washer Two clamping nuts Toothed washer * D Models: Operation indicator (red), Setting indicator (green) E/Y Models: Operation indicator (red) * D Models: Operation indicator (red), Setting indicator (green) E/Y Models: Operation indicator (red) Mounting Hole Dimensions Dimensions F (mm) M8 M12 M18 M30 8.5 +00.5 dia. 12.5 +00.5 dia. 18.5 +00.5 dia. 30.5 +00.5 dia. F 28 E2E Pre-wired Connector Models (Shielded) Mounting Hole Dimensions F Dimension F (mm) Diagram 30 E2E-X2D1-M1TGJ-U *3 30 15 dia. M12 M18 M30 12.5 +00.5 dia. 18.5 +00.5 dia. 30.5 +00.5 dia. 7 26 8 13 3 *1 Indicators *2 Two clamping nuts Toothed washer M8 x 1 Diagram 31 E2E-X3D1-M1GJ E2E-X3D1-M1J-T E2E-X3D1-M1TGJ-U *3 38 21 dia. M12 x 1 *1. 4-dia. vinyl-insulated round cable, Standard length: 300 mm *2. Operation indicator (red), Setting indicator (green) *3. The connectors for M1TGJ models are XS5 Smartclick connectors 9 33 10 4 17 *1 Indicators *2 Two clamping nuts Toothed washer M12 x 1 Diagram 33 E2E-X7D1-M1GJ E2E-X7D1-M1J-T E2E-X7D1-M1TGJ-U *3 43 29 dia. 12 38 10 4 24 *1 M12 x 1 Indicators *2 Two clamping nuts *1. 6-dia. vinyl-insulated round cable, Standard length: 300 mm Toothed washer *2. Operation indicator (red), Setting indicator (green) *3. The connectors for M1TGJ models are XS5 Smartclick connectors M18 x 1 Diagram 35 E2E-X10D1-M1GJ E2E-X10D1-M1J-T E2E-X10D1-M1TGJ-U *3 M12 x 1 *1. 4-dia. vinyl-insulated round cable, Standard length: 300 mm *2. Operation indicator (red), Setting indicator (green) *3. The connectors for M1TGJ models are XS5 Smartclick connectors 48 42 dia. 12 43 36 10 5 *1 Indicators *2 M30 x 1.5 Two clamping nuts Toothed washer M12 x 1 *1. 6-dia. vinyl-insulated round cable, Standard length: 300 mm *2. Operation indicator (red), Setting indicator (green) *3. The connectors for M1TGJ models are XS5 Smartclick connectors Pre-wired Connector Models (Unshielded) Diagram 32 E2E-X8MD1-M1GJ 38 21 dia. 9 33 7 17 4 10 9 dia. *1 M12 x 1 Indicators *2 Two clamping nuts Toothed washer M12 x 1 *1. 4-dia. vinyl-insulated round cable, Standard length: 300 mm *2. Operation indicator (red), Setting indicator (green) 29 E2E Diagram 34 E2E-X14MD1-M1GJ 43 12 38 29 dia. 10 10 4 24 14.8 dia. Indicators*2 M18 x 1 Two clamping nuts Toothed washer Diagram 36 E2E-X20MD1-M1GJ 48 42 dia. *1 M12 x 1 *1. 6-dia. vinyl-insulated round cable, Standard length: 300 mm *2. Operation indicator (red), Setting indicator (green) 12 43 13 36 10 5 26.8 dia. *1 M12 x 1 Indicators*2 M30 x 1.5 Two clamping nuts Toothed washer *1. 6-dia. vinyl-insulated round cable, Standard length: 300 mm *2. Operation indicator (red), Setting indicator (green) Dimensions for Proximity Sensors with Sensor I/O Connectors Shielded Models Straight Connectors Unshielded Models Straight Connectors L1 L-shape Connectors L1 L-shape Connectors Dimensions with the XS2F Connected Dimension Sensor diameter M8 DC M12* AC M18 M30 (Unit: mm) L1 L2 Approx. 75 Approx. 80 Approx. 85 Approx. 85 Approx. 90 Approx. 62 Approx. 67 Approx. 72 Approx. 72 Approx. 77 * The overall length of the Sensor is different between AC and DC Models for Sensors with diameters of M12. This will change the dimension when the I/O Connector is connected. Dimensions with the XS3F Connected L2 L2 Dimension Sensor diameter M8 (Unit: mm) L1 L2 Approx. 65 Approx. 54 Accessories (Order Separately) Sensor I/O Connectors Refer to Introduction to Sensor I/O Connectors for details. Mounting Brackets Protective Covers Sputter Protective Covers Refer to Y92@ for details. 30