Copyright © 2014 Future Technology Devices International Limited 1
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
Future Technology Devices
International Ltd.
FT121
(Enhanced USB Device
Controller with SPI Slave IC)
The FT121 is a USB generic interface
controller with the following advanced
features:
USB 2.0 Full Speed compatible
High performance USB device controller with
integrated SIE, endpoint buffer, transceiver
and voltage regulators
Fully integrated clock generation with no
external crystal required
Supports Serial Parallel interface (SPI) slave to
external microcontroller
Supports up to 8 bi-directional endpoints with
total 2k bytes endpoint buffer
Max packet size is 504 bytes for isochronous
endpoint and 64 bytes for
control/bulk/interrupt endpoint
Double buffer scheme for any endpoint
increases data transfer throughput
Multiple interrupt modes to facilitate both bulk
and isochronous transfers
USB Battery Charger detection allowing
optimized charging profile
Integrated DP pull-up resistor for USB
connection
Supports bus-powered or self-powered
applications
VCC power supply operation at 3.3V or 5V
Internal 1.8V and 3.3V LDO regulators
VCC IO level range from 1.8V to 3.3V
Integrated power-on-reset circuit
UHCI/OHCI/EHCI host controller compatible
-40°C to 85°C extended operating temperature
range
Available in Pb-free TSSOP-16 and QFN-16
packages (RoHS compliant)
Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced
in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are
supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology
Devices International Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your
statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in
which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminary
information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by
the publication of this document. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow
G41 1HH United Kingdom. Scotland Registered Company Number: SC136640
Copyright © 2014 Future Technology Devices International Limited 2
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
1 Typical Applications
Provide USB port to Microcontrollers
Provide USB port to FPGA’s
USB Industrial Control
Mass storage data transfers for multitude of
embedded systems applications, including
medical, industrial data-logger, power-
metering, and test instrumentation
Utilising USB to add system modularity
Isochronous support for video applications in
security, industrial control, and quality
inspections
1.1 Part Numbers
Part Number
Package
FT121T-x
TSSOP-16
FT121Q-x
QFN-16
Note: Packaging codes for x is:
- R: Taped and Reel, (TSSOP is 2,500pcs per reel, QFN is 6,000pcs per reel).
- U: Tube packing, 96pcs per tube (TSSOP only)
- T: Tray packing, 490pcs per tray (QFN only)
For example: FT121T-R is 2,500pcs taped and reel packing
1.2 USB Compliant
At the time of writing this datasheet, the FT121 was in the process of completing USB compliance testing.
Copyright © 2014 Future Technology Devices International Limited 3
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
2 Block Diagrams
Figure 2-1 FT121 Block Diagram
For a description of each function please refer to Section 4.
Copyright © 2014 Future Technology Devices International Limited 4
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
Table of Contents
1 Typical Applications ...................................................................... 2
1.1 Part Numbers...................................................................................... 2
1.2 USB Compliant .................................................................................... 2
2 Block Diagrams ............................................................................ 3
3 Device Pin Out and Signal Description .......................................... 6
3.1 TSSOP-16 Package Pin Out ................................................................. 6
3.2 QFN-16 Package Pin Out ..................................................................... 6
3.3 Pin Description ................................................................................... 7
4 Function Description..................................................................... 9
4.1 Functional Block Descriptions ............................................................. 9
4.2 Interrupt Modes ................................................................................ 10
4.3 SPI Slave Interface ........................................................................... 10
4.3.1 4-wire write operation ................................................................................................ 11
4.3.2 4-wire read operation ................................................................................................. 11
4.3.3 3-wire write operation ................................................................................................ 12
4.3.4 3-wire read operation ................................................................................................. 12
5 Endpoint Buffer Management ..................................................... 14
5.1 Endpoint Buffer Management in Default Mode .................................. 14
5.2 Endpoint Buffer Management in Enhanced Mode .............................. 15
6 Commands and Registers ........................................................... 17
6.1 Command Summary .......................................................................... 17
6.2 Initialization Commands ................................................................... 22
6.2.1 Set Address Enable .................................................................................................... 22
6.2.2 Set Endpoint Enable ................................................................................................... 22
6.2.3 Set Mode .................................................................................................................. 22
6.2.4 Set Interrupt ............................................................................................................. 24
6.2.5 Set Endpoint Configuration (for Enhanced Mode) ........................................................... 24
6.3 Data Flow Commands ....................................................................... 25
6.3.1 Read Interrupt Register .............................................................................................. 25
6.3.2 Select Endpoint ......................................................................................................... 27
6.3.3 Read Last Transaction Status ...................................................................................... 27
6.3.4 Read Endpoint Status ................................................................................................. 28
6.3.5 Read Buffer ............................................................................................................... 29
6.3.6 Write Buffer .............................................................................................................. 29
6.3.7 Clear Buffer .............................................................................................................. 29
6.3.8 Validate Buffer .......................................................................................................... 29
6.3.9 Set Endpoint Status ................................................................................................... 30
6.3.10 Acknowledge Setup ................................................................................................ 30
Copyright © 2014 Future Technology Devices International Limited 5
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
6.4 General Commands ........................................................................... 30
6.4.1 Read Current Frame Number ....................................................................................... 31
6.4.2 Send Resume ............................................................................................................ 31
6.4.3 Set 3-wire Mode ........................................................................................................ 31
6.4.4 Read Vendor ID ......................................................................................................... 32
6.4.5 Read Product ID ........................................................................................................ 32
6.4.6 Read FTDI ID ............................................................................................................ 32
6.4.7 Set IO Pad Drive Strength........................................................................................... 32
7 Application Information ............................................................. 33
8 Devices Characteristics and Ratings ........................................... 34
8.1 Absolute Maximum Ratings............................................................... 34
8.2 DC Characteristics............................................................................. 35
8.3 AC Characteristics ............................................................................. 36
9 Package Parameters ................................................................... 38
9.1 TSSOP-16 Package Dimensions ........................................................ 38
9.2 TSSOP-16 Package Markings ........................................................... 39
9.3 QFN-16 Package Dimensions ............................................................ 40
9.4 QFN-16 Package Markings ............................................................... 41
9.5 Solder Reflow Profile ........................................................................ 41
10 Contact Information ................................................................... 43
Appendix A References ........................................................................... 44
Appendix B - List of Figures and Tables ..................................................... 44
Appendix C - Revision History .................................................................... 46
Copyright © 2014 Future Technology Devices International Limited 6
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
3 Device Pin Out and Signal Description
3.1 TSSOP-16 Package Pin Out
Figure 3-1 TSSOP-16 package schematic symbol
3.2 QFN-16 Package Pin Out
Figure 3-2 QFN-16 package schematic symbol
NOTE: Bottom Side centre pads not shown on QFN Pin Out:
Ground Bottom View Location = Upper right
VCCIO Bottom View Location = Lower right
VOUT3V3 Bottom View Location = Lower left
VCC Bottom View Location = Upper left
See QFN Package information in Section 9.3 below for more details. They may be left unconnected.
Copyright © 2014 Future Technology Devices International Limited 7
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
3.3 Pin Description
PIN No.
(QFN-
16)
PIN NAME
TYPE
DESCRIPTION
15
BCD_n
OD
USB Charger detector output
16
SCLK
I
SPI clock input
1
SS_n
I
SPI slave select input
2
GND
P
Ground
3
VCCIO
P
IO Supply Voltage; 1.8V, 2.5V or 3.3V
4
SUSPEND
I,OD
Device suspend (output) and wakeup (input)
5
INT_n
OD
Interrupt (Active Low)
6
MISO
O
4-wire mode: SPI slave output
3-wire mode: no function. Leave it un-connected
7
MOSI
I/IO
4-wire mode: SPI salve input
3-wire mode: SPI data input/output
8
VBUS_S
I
Vbus sensing input
9
RESET_n
I
Asynchronous reset (Active Low)
10
VOUT3V3
P
3.3V regulator output for 5V operation;
To operate the IC at 3.3 V, supply 3.3 V to both
the VCC and VOUT3V3 pins
11
VCC
P
Power supply (3.3V or 5V)
12
GND
P
Ground
13
DM
AIO
USB data signal minus
14
DP
AIO
USB data signal plus
17
GND
P
Ground
Center bottom pad may be left unconnected
18
VCCIO
P
IO Supply Voltage; 1.8V, 2.5V or 3.3V
Center bottom pad may be left unconnected
19
VOUT3V3
P
3.3V regulator output for 5V operation;
To operate the IC at 3.3 V, supply 3.3 V to both
the VCC and VOUT3V3 pins
Center bottom pad may be left unconnected
20
VCC
P
Power supply (3.3V or 5V)
Center bottom pad may be left unconnected
Table 3.1 FT121 Pin Description
Copyright © 2014 Future Technology Devices International Limited 8
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
Note: a) Pin name with suffix “_n” denotes active low input/output signal.
b) Symbol used for pin TYPE:
OD : Open Drain Output
O : Output
IO : Bi-directional Input and Output
I : Plain input
AIO : Analog Input and Output
P : Power or ground
Copyright © 2014 Future Technology Devices International Limited 9
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
4 Function Description
The FT121 is a USB device controller which interfaces with microcontrollers via an SPI slave interface.
4.1 Functional Block Descriptions
The following sections describe the function of each block. Please refer to the block diagram shown in
Figure 2-1.
+1.8V LDO Regulator. The +1.8V LDO regulator generates the +1.8V reference voltage for the internal
core of the IC with input capabilities from 3.3V or 5V.
+3.3V LDO Regulator. The +3.3V LDO regulator generates the +3.3V supply voltage for the USB
transceiver. An external decoupling capacitor needs to be attached to the VOUT3V3 regulator output pin.
The regulator also provides +3.3V power to the 1.5kΩ internal pull up resistor on DP pin. The allowable
input voltages are 5V or 3.3V. When using 3.3V as the input voltage, the VCC and VOUT3V3 pins should
be tied together. This will result in the regulator being by-passed.
USB Transceiver. The USB Transceiver cell provides the USB 1.1 / USB 2.0 full-speed physical interface.
Output drivers provide +3.3V level slew rate control, while a differential input and two single ended input
receivers provide data in, Single-Ended-0 (SE0) and USB reset detection conditions respectfully. A 1.5kΩ
pull up resistor on DP is incorporated.
DPLL. The DPLL cell locks on to the incoming NRZI USB data and generates recovered clock and data
signals.
Internal Oscillator. The Internal Oscillator cell generates a reference clock. This provides an input to
the Clock Multiplier function.
Clock Multiplier. The 12MHz and 48MHz reference clock signals for various internal blocks can be
generated from the reference clock via the oscillator functions and clock multiplier circuitry.
Serial Interface Engine (SIE). The Serial Interface Engine (SIE) block performs the parallel to serial
and serial to parallel conversion of the USB data. In accordance with the USB 2.0 specification, it
performs bit stuffing/un-stuffing and CRC5/CRC16 generation. It also checks the CRC on the USB data
stream.
USB Protocol Engine. The USB Protocol Engine manages the data stream from the device USB control
endpoint. It handles the low level USB protocol requests generated by the USB host controller. The
Protocol Engine also includes a memory management unit which handles endpoint buffers.
Copyright © 2014 Future Technology Devices International Limited 10
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
OUT Buffer. Data sent from the USB host controller to FT121 via the USB data OUT endpoint is stored in
the OUT buffer. Data is removed from the OUT buffer to system memory under control of the parallel
interface block.
IN Buffer. Data from system memory is stored in the IN buffer. The USB host controller removes data
from the IN buffer by sending a USB request for data from the device data IN endpoint.
RESET Generator. The integrated Reset Generator cell provides a reliable power-on reset to the device
internal circuitry at power up. The RESET_n input pin allows an external device to reset the FT121.
SPI Controller Block. The SPI slave controller provides control and data interfaces between the external
MCU and internal registers and endpoint buffers. It supports 4-wire (default) or 3-wire SPI operation.
4.2 Interrupt Modes
The FT121 interrupt pin (INT_n) can be programmed to generate an interrupt in different modes. The
interrupt source can be any bit in the Interrupt Register, an SOF packet being received, or both. The
interrupt modes are selectable by two register bits, one is the SOF-only Interrupt Mode bit (bit 7 of Clock
Division Factor register), and the other is the Interrupt Pin Mode bit (bit 5 of Interrupt Configuration
register).
Interrupt
mode
Bit SOF-only
Interrupt
Mode
Bit Interrupt
Pin Mode
Interrupt source
0
0
0
Any bit in Interrupt register
1
0
1
Any bit in Interrupt register and SOF
2
1
X
SOF only
Table 4.1 Interrupt modes
4.3 SPI Slave Interface
The SPI slave interface supports 4-wire (default) and 3-wire operation. In 4-wire operation the SPI
master will drive data on the MOSI pin and the SPI slave will drive data on the MISO pin. In 3-wire
operation both SPI master and SPI slave share the same data pin (MOSI pin becomes a bi-directional
pin). Upon power-on or hardware reset, the FT121 SPI slave interface is in 4-wire mode. The 3-wire
operation is enabled when a Set 3-wire command is issued to the FT121.
The SPI protocol will follow a command + data format where a command is transmitted after SS_n is
asserted and each subsequent byte will be a data byte. When all data bytes for this command are
completed the SS_n is de-asserted. This can be seen in Figure 4-1.
Copyright © 2014 Future Technology Devices International Limited 11
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
SS_n
Command Write Data
SCLK
MOSI
MISO
01 6 7 01 6 7
Command Write Data
Read Data
Figure 4-1 SPI access
The SPI slave supports SPI mode 1 (CPOL=0, CPHA=1). This means the rising edge is the driving edge
while the falling edge is the sample edge. The drive edge is always before the sample edge.
The maximum SPI clock supported is 20MHz, for both 4-wire and 3-wire modes. Refer to the AC
characteristics section for SPI timing figures.
4.3.1 4-wire write operation
When the SPI master performs a data write operation, it drives the SS_n line low, sends the 8-bit
command byte on MOSI line, followed by sending of the data bytes. The length of the data byte ranges
from 0 to maximum 506, depending on the command type. The master will signal the end of the data
write operation by drive the SS_n line high.
Figure 4-2 4-wire write operation
4.3.2 4-wire read operation
When the SPI master performs a data read operation, it drives the SS_n line low and sends the 8-bit
command byte on MOSI line. The FT121 will output data bytes on the MISO line. The length of the data
byte ranges from 0 to maximum 506, depending on the command type. The master will signal the end of
the data read operation by drive the SS_n line high.
Copyright © 2014 Future Technology Devices International Limited 12
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
Figure 4-3 4-wire read operation
4.3.3 3-wire write operation
When the SPI master performs a data write operation, it drives the SS_n line low, sends the 8-bit
command byte on MOSI line, followed by sending the data bytes. The length of the data byte ranges from
0 to maximum 506, depending on the command type. The master will signal the end of the data write
operation by drive the SS_n line high.
Figure 4-4 3-wire write operation
4.3.4 3-wire read operation
When the SPI master performs a data read operation, it drives the SS_n line low andsends the 8-bit
command byte on MOSI line. The master will stop driving the MOSI line. The FT121 will output data bytes
on the MOSI line. The length of the data byte ranges from 0 to maximum 506, depending on the
command type. The master will signal the end of the data read operation by drive the SS_n line high.
Figure 4-5 3-wire read operation
It is important that bus contention should be avoided during the bus turnaround period i.e. moving
from the command byte to a read byte. In this instance the master will stop driving at the same clock
edge (rising edge) as the slave starts to drive. To avoid bus contention the FT121 will implement delays
so that it only starts to drive the MOSI line at least 5ns after the SCLK driving edge this will give the
master a minimum of 5ns to stop driving MOSI, which should ensure no bus contentions. At this bus
turnaround point it’s also more natural for a clash not to occur, as the master is the source of the clock,
so will drive the clock and MOSI off at similar times. For the slave to drive MOSI it has to pass the clock
Copyright © 2014 Future Technology Devices International Limited 13
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
through the I/O buffers, into the internal circuits, clock MOSI and then get MOSI out through the output
buffers. This long path in and out of the slave will have an inherent delay of a few nanoseconds.
Copyright © 2014 Future Technology Devices International Limited 14
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
5 Endpoint Buffer Management
The FT121 has 2 modes of operation for command and memory management: the default mode and the
enhanced mode. The buffer management schemes are different in these two modes. Upon reset the
default mode is functional. The enhanced mode is activated when any of the Set Endpoint Configuration
commands (B0h BFh) are received.
5.1 Endpoint Buffer Management in Default Mode
In default mode the FT121 has 3 bi-directional endpoints (EP0, EP1 and EP2). EP0 is the control endpoint,
with 16 bytes maximum packet size for both the control OUT and control IN endpoints. EP1 can be used
as either a bulk endpoint or an interrupt endpoint, with 16 bytes maximum packet size for both OUT and
IN endpoints. Table 5.1 shows the endpoint type and maximum packet size for EP0 and EP1.
Endpoint
Number (EP)
Endpoint
Index (EPI)
Endpoint
Direction
Transfer Type
Max Packet Size
0
0
1
OUT
IN
Control
Control
16
16
1
2
3
OUT
IN
Bulk/Interrupt
Bulk/Interrupt
16
16
Table 5.1 Endpoint configuration for EP0 and EP1
EP2 is the primary endpoint. It can be configured as either a bulk/interrupt or isochronous endpoint. The
maximum packet size allowed for EP2 depends on the mode of configuration through the Set Mode
command. Table 5.2 shows all the 4 endpoint configuration modes for EP2.
EP2 Endpoint
Configuration
Mode
Endpoint
Index (EPI)
Endpoint
Direction
Transfer Type
Max Packet Size
0
(default)
4
5
OUT
IN
Bulk/Interrupt
Bulk/Interrupt
64
64
1
4
OUT
Isochronous
128
2
5
IN
Isochronous
128
3
4
5
OUT
IN
Isochronous
Isochronous
64
64
Table 5.2 Endpoint configuration for EP2
Copyright © 2014 Future Technology Devices International Limited 15
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
As the primary endpoint, EP2 is suitable for transmitting or receiving relatively large data. To improve the
data throughput, EP2 is implemented with double buffering. This allows the concurrent operation between
USB bus access and MCU local bus access. For example, for EP2 IN endpoint (EPI5), the USB host can
read data from FT121 Buffer 0 while the local MCU is writing to Buffer 1 at the same time. The USB host
can subsequently read from the FT121 Buffer 1 without waiting for it to be filled. Buffer switching is
handled automatically by FT121.
5.2 Endpoint Buffer Management in Enhanced Mode
In enhanced mode the FT121 supports a dedicated 1kB buffer for IN packets and a dedicated 1kB buffer
for OUT packets. The OUT/IN buffer can be allocated to any endpoint with the same direction, up to a
maximum of 504 bytes double buffered (1008 bytes in total) to one endpoint. 504 is the maximum byte
count as there are 1024 bytes in total per OUT/IN Buffer and 8 bytes for IN and OUT packets on control
endpoint 0 must always be reserved. Control, interrupt and bulk endpoints can have a maximum packet
size of 64 bytes and only isochronous endpoints can be allocated more than 64 bytes.
Isochronous modes can have larger buffer sizes as USB packets can be larger than 64 bytes for
isochronous transfer. Isochronous buffers are managed in the same way as bulk, interrupt and control
buffers i.e. a buffer is for one USB packet only and will not span more than one USB packet.
An example of buffer configurations follows, where Configuration 1 and 2 have larger isochronous buffers.
Table 5.3 Example buffer configuration
EP Buffer EP Buffer EP Buffer
7 1
7 0
6 1
6 0 5 (ISO) 1
5 1 6 1
5 0 6 0
4 1 2 1
4 0 2 0
3 1
3 0
2 1 5 (ISO) 0
2 0
1 1
1 0
0 1
0 1 0 1
0 0 0 0 0 0
0
1
1 (ISO)
0
1
1 (ISO)
Configuration 2
Each cell indicates a 64 byte block
Configuration 0
Configuration 1
7
(ISO)
7
(ISO)
Copyright © 2014 Future Technology Devices International Limited 16
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
The endpoint buffer configurations, settable using the Set Endpoint Configuration command, are as
follows:
Endpoint buffer size register setting (0b’)
Non-isochronous endpoint
Isochronous endpoint
0000
8 bytes
16 bytes
0001
16 bytes
32 bytes
0010
32 bytes
48 bytes
0011
64 bytes
64 bytes
0100
-
96 bytes
0101
-
128 bytes
0110
-
160 bytes
0111
-
192 bytes
1000
-
256 bytes
1001
-
320 bytes
1010
-
384 bytes
1011
-
504 bytes
1100-1111
-
-
Table 5.4 Endpoint Maximum Packet Size
Note: 504 is the maximum byte count as there are 1024 bytes in total and 8 bytes IN and OUT packets
for control endpoint 0 must always be reserved.
Copyright © 2014 Future Technology Devices International Limited 17
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
6 Commands and Registers
The FT121 supports two command sets: a default command set (Table 6.1) and an enhanced command
set (Table 6.2). The enhanced command set is activated if any of the Set Endpoint Configuration
commands (0xB0-0xBF) are received by the FT121. Otherwise, the default command set shall be valid.
6.1 Command Summary
Command Name
Target
Code (hex)
Data phase
Initialization Commands
Set Address Enable
Device
D0h
Write 1 byte
Set Endpoint Enable
Device
D8h
Write 1 byte
Set Mode
Device
F3h
Write 2 bytes
Set Interrupt
Device
FBh
Write 1 byte
Data Flow Commands
Read Interrupt Register
Device
F4h
Read 2 bytes
Select Endpoint
Endpoint 0 OUT
00h
Read 1 byte (optional)
Endpoint 0 IN
01h
Read 1 byte (optional)
Endpoint 1 OUT
02h
Read 1 byte (optional)
Endpoint 1 IN
03h
Read 1 byte (optional)
Endpoint 2 OUT
04h
Read 1 byte (optional)
Endpoint 2 IN
05h
Read 1 byte (optional)
Read Last Transaction Status
Endpoint 0 OUT
40h
Read 1 byte
Endpoint 0 IN
41h
Read 1 byte
Endpoint 1 OUT
42h
Read 1 byte
Endpoint 1 IN
43h
Read 1 byte
Endpoint 2 OUT
44h
Read 1 byte
Endpoint 2 IN
45h
Read 1 byte
Read Endpoint Status
Endpoint 0 OUT
80h
Read 1 byte
Endpoint 0 IN
81h
Read 1 byte
Endpoint 1 OUT
82h
Read 1 byte
Endpoint 1 IN
83h
Read 1 byte
Endpoint 2 OUT
84h
Read 1 byte
Copyright © 2014 Future Technology Devices International Limited 18
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
Command Name
Target
Code (hex)
Data phase
Endpoint 2 IN
85h
Read 1 byte
Read Buffer
Selected Endpoint
E0h
Read multiple bytes
Write Buffer
Selected Endpoint
F0h
Write multiple bytes
Set Endpoint Status
Endpoint 0 OUT
50h
Write 1 byte
Endpoint 0 IN
51h
Write 1 byte
Endpoint 1 OUT
52h
Write 1 byte
Endpoint 1 IN
53h
Write 1 byte
Endpoint 2 OUT
54h
Write 1 byte
Endpoint 2 IN
55h
Write 1 byte
Acknowledge Setup
Selected Endpoint
F1h
None
Clear Buffer
Selected Endpoint
F2h
None
Validate Buffer
Selected Endpoint
FAh
None
General Commands
Read Current Frame Number
Device
F5h
Read 1 or 2 bytes
Send Resume
Device
F6h
None
Table 6.1 FT121 default command set
Command Name
Target
Code (hex)
Data phase
Initialization Commands
Set Address Enable
Device
D0h
Write 1 byte
Set Endpoint Enable
Device
D8h
Write 1 byte
Set Mode
Device
F3h
Write 2 bytes
Set Interrupt
Device
FBh
Write 1 byte
Set Endpoint Configuration
Endpoint 0 OUT
B0h
Write 1 byte
Endpoint 0 IN
B1h
Write 1 byte
Endpoint 1 OUT
B2h
Write 1 byte
Endpoint 1 IN
B3h
Write 1 byte
Endpoint 2 OUT
B4h
Write 1 byte
Endpoint 2 IN
B5h
Write 1 byte
Copyright © 2014 Future Technology Devices International Limited 19
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
Command Name
Target
Code (hex)
Data phase
Endpoint 3 OUT
B6h
Write 1 byte
Endpoint 3 IN
B7h
Write 1 byte
Endpoint 4 OUT
B8h
Write 1 byte
Endpoint 4 IN
B9h
Write 1 byte
Endpoint 5 OUT
BAh
Write 1 byte
Endpoint 5 IN
BBh
Write 1 byte
Endpoint 6 OUT
BCh
Write 1 byte
Endpoint 6 IN
BDh
Write 1 byte
Endpoint 7 OUT
BEh
Write 1 byte
Endpoint 7 IN
BFh
Write 1 byte
Data Flow Commands
Read Interrupt Register
Device
F4h
Read 1 to 4 bytes
Select Endpoint
Endpoint 0 OUT
00h
Read 1 byte (optional)
Endpoint 0 IN
01h
Read 1 byte (optional)
Endpoint 1 OUT
02h
Read 1 byte (optional)
Endpoint 1 IN
03h
Read 1 byte (optional)
Endpoint 2 OUT
04h
Read 1 byte (optional)
Endpoint 2 IN
05h
Read 1 byte (optional)
Endpoint 3 OUT
06h
Read 1 byte (optional)
Endpoint 3 IN
07h
Read 1 byte (optional)
Endpoint 4 OUT
08h
Read 1 byte (optional)
Endpoint 4 IN
09h
Read 1 byte (optional)
Endpoint 5 OUT
0Ah
Read 1 byte (optional)
Endpoint 5 IN
0Bh
Read 1 byte (optional)
Endpoint 6 OUT
0Ch
Read 1 byte (optional)
Endpoint 6 IN
0Dh
Read 1 byte (optional)
Endpoint 7 OUT
0Eh
Read 1 byte (optional)
Endpoint 7 IN
0Fh
Read 1 byte (optional)
Read Last Transaction Status
Endpoint 0 OUT
40h
Read 1 byte
Copyright © 2014 Future Technology Devices International Limited 20
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
Command Name
Target
Code (hex)
Data phase
Endpoint 0 IN
41h
Read 1 byte
Endpoint 1 OUT
42h
Read 1 byte
Endpoint 1 IN
43h
Read 1 byte
Endpoint 2 OUT
44h
Read 1 byte
Endpoint 2 IN
45h
Read 1 byte
Endpoint 3 OUT
46h
Read 1 byte
Endpoint 3 IN
47h
Read 1 byte
Endpoint 4 OUT
48h
Read 1 byte
Endpoint 4 IN
49h
Read 1 byte
Endpoint 5 OUT
4Ah
Read 1 byte
Endpoint 5 IN
4Bh
Read 1 byte
Endpoint 6 OUT
4Ch
Read 1 byte
Endpoint 6 IN
4Dh
Read 1 byte
Endpoint 7 OUT
4Eh
Read 1 byte
Endpoint 7 IN
4Fh
Read 1 byte
Read Endpoint Status
Endpoint 0 OUT
80h
Read 1 byte
Endpoint 0 IN
81h
Read 1 byte
Endpoint 1 OUT
82h
Read 1 byte
Endpoint 1 IN
83h
Read 1 byte
Endpoint 2 OUT
84h
Read 1 byte
Endpoint 2 IN
85h
Read 1 byte
Endpoint 3 OUT
86h
Read 1 byte
Endpoint 3 IN
87h
Read 1 byte
Endpoint 4 OUT
88h
Read 1 byte
Endpoint 4 IN
89h
Read 1 byte
Endpoint 5 OUT
8Ah
Read 1 byte
Endpoint 5 IN
8Bh
Read 1 byte
Endpoint 6 OUT
8Ch
Read 1 byte
Endpoint 6 IN
8Dh
Read 1 byte
Copyright © 2014 Future Technology Devices International Limited 21
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
Command Name
Target
Code (hex)
Data phase
Endpoint 7 OUT
8Eh
Read 1 byte
Endpoint 7 IN
8Fh
Read 1 byte
Read Buffer
Selected Endpoint
E0h
Read multiple bytes
Write Buffer
Selected Endpoint
F0h
Write multiple bytes
Set Endpoint Status
Endpoint 0 OUT
50h
Write 1 byte
Endpoint 0 IN
51h
Write 1 byte
Endpoint 1 OUT
52h
Write 1 byte
Endpoint 1 IN
53h
Write 1 byte
Endpoint 2 OUT
54h
Write 1 byte
Endpoint 2 IN
55h
Write 1 byte
Endpoint 3 OUT
56h
Write 1 byte
Endpoint 3 IN
57h
Write 1 byte
Endpoint 4 OUT
58h
Write 1 byte
Endpoint 4 IN
59h
Write 1 byte
Endpoint 5 OUT
5Ah
Write 1 byte
Endpoint 5 IN
5Bh
Write 1 byte
Endpoint 6 OUT
5Ch
Write 1 byte
Endpoint 6 IN
5Dh
Write 1 byte
Endpoint 7 OUT
5Eh
Write 1 byte
Endpoint 7 IN
5Fh
Write 1 byte
Acknowledge Setup
Selected Endpoint
F1h
None
Clear Buffer
Selected Endpoint
F2h
None
Validate Buffer
Selected Endpoint
FAh
None
General Commands
Send Resume
Device
F6h
None
Read Current Frame Number
Device
F5h
Read 1 or 2 bytes
Set 3-wire Mode
Device
E8h
None
Set IO Pad Drive Strength
Device
E9h
Write 1 byte
Copyright © 2014 Future Technology Devices International Limited 22
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
Command Name
Target
Code (hex)
Data phase
Read Vendor ID
Device
EBh
Read 2 bytes
Read Product ID
Device
EAh
Read 2 bytes
Read FTDI ID
Device
EDh
Read 1 byte
Table 6.2 enhanced command set
6.2 Initialization Commands
6.2.1 Set Address Enable
Command : D0h
Data : Write 1 byte
Bit
Symbol
Reset
Description
6-0
Address
0b’0000000
USB assigned device address. A bus reset will reset all
address bits to 0.
7
Enable
0
Function enable. A bus reset will automatically enable the
function at default address 0.
Table 6.3 Address Enable Register
6.2.2 Set Endpoint Enable
Command : D8h
Data : Write 1 byte
Bit
Symbol
Reset
Description
0
EP_Enable
0
Enable all endpoints (Note EP0 is always enabled
regardless the setting of EP_Enable bit). Endpoints can
only be enabled when the function is enabled.
7-1
Reserved
0b’0000000
Reserved, write to 0
Table 6.4 Endpoint Enable Register
6.2.3 Set Mode
Command : F3h
Data : Write 2 bytes
Bit
Symbol
Reset
Description
1-0
Reserved
0b’00
Reserved, write to 0
Copyright © 2014 Future Technology Devices International Limited 23
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
Bit
Symbol
Reset
Description
2
Clock Running
1
0: internal clocks stop during USB suspend
1: internal clocks continue running during USB suspend
This bit must be set to ‘0’ for bus powered application in
order to meet the USB suspend current requirement.
Note: The programmed value will not be changed by a
bus reset.
3
Interrupt Mode
1
0: interrupt will not generate on NAK or Error
transactions
1: interrupt will generate on NAK and Error transactions
Note: The programmed value will not be changed by a
bus reset.
4
DP_Pullup
0
0: Pullup resistor on DP pin disabled
1: Pullup resistor on DP pin enabled when Vbus is
present
Note: The programmed value will not be changed by a
bus reset.
5
Reserved
0
Reserved, write to 0
7-6
Endpoint Configuration
Mode
0b’00
Set the endpoint configuration mode for EP2.
00: Mode 0 (Non-ISO Mode)
01: Mode 1 (ISO-OUT Mode)
10: Mode 2 (ISO-IN Mode)
11: Mode 3 (ISO-IO Mode)
In Enhanced Mode, these 2 bits are reserved. The
Endpoint Configuration will be done through separate
command. See “Set Endpoint Configuration” commands.
Table 6.5 Configuration Register (Byte 1)
Bit
Symbol
Reset
Description
3-0
Reserved
0b’1011
Reserved, write to 0b’1111
5-4
Reserved
0b’00
Reserved, write to 0
6
SET_TO_ONE
0
This bit must be set to 1
7
SOF-only Interrupt
Mode
0
0: normal operation
1: interrupt will generate on receiving SOF packet only,
regardless of the value of the Interrupt Pin Mode bit in
the Interrupt configuration register.
Table 6.6 Configuration Register (Byte 2)
Copyright © 2014 Future Technology Devices International Limited 24
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
6.2.4 Set Interrupt
Command : FBh
Data : Write 1 byte
Bit
Symbol
Reset
Description
4-0
Reserved
0b’00000
Reserved, write to 0b’00000
5
Interrupt Pin Mode
0
0: normal operation. Interrupt will generate if any bit in
the interrupt register is set.
1: interrupt will generate upon receiving a SOF packet or
if any bit in the interrupt register is set.
6
EPI4 Interrupt Enable
0
Interrupt Enable for endpoint index 4.
For enhanced mode this bit has no function. EPI4
interrupt is always enabled.
7
EPI5 Interrupt Enable
0
Interrupt Enable for endpoint index 5.
For enhanced mode this bit has no function. EPI5
interrupt is always enabled
Table 6.7 Interrupt Configuration Register
6.2.5 Set Endpoint Configuration (for Enhanced Mode)
Command : B0-BFh
Data : Write 1 byte
Bit
Symbol
Reset
Description
0
Endpoint Enabled
0
Enable or disable the endpoint index associated with the
command
2-1
Endpoint Type
0b’00
Endpoint type
00: control
01: bulk or interrupt
10: isochronous
11: reserved
6-3
Max Packet Size
0b’0000
Maximum USB packet size for this endpoint. Defines the
IN buffer or OUT buffer size for the endpoint. Refer to
Table 5.4 for full details on the buffer configuration.
7
Reserved
0
Reserved, write to 0
Table 6.8 Endpoint Configuration Register
Copyright © 2014 Future Technology Devices International Limited 25
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
6.3 Data Flow Commands
6.3.1 Read Interrupt Register
Command : F4h
Data : Read 1 or 2 bytes (Default Mode); Read 1-4 bytes (Enhanced Mode)
Bit
Symbol
Reset
Description
0
Endpoint 0 Out
0
Interrupt for endpoint 0 OUT buffer. Cleared by Read
Last Transaction Status command.
1
Endpoint 0 In
0
Interrupt for endpoint 0 IN buffer. Cleared by Read Last
Transaction Status command.
2
Endpoint 1 Out
0
Interrupt for endpoint 1 OUT buffer. Cleared by Read
Last Transaction Status command.
3
Endpoint 1 In
0
Interrupt for endpoint 1 IN buffer. Cleared by Read Last
Transaction Status command.
4
Endpoint 2 Out
0
Interrupt for endpoint 2 OUT buffer. Cleared by Read
Last Transaction Status command.
5
Endpoint 2 In
0
Interrupt for endpoint 2 IN buffer. Cleared by Read Last
Transaction Status command.
6
Bus Reset
0
Interrupt for bus reset. This bit will be cleared after
reading.
7
Suspend Change
0
Interrupt for USB bus suspend status change. This bit
will be set to ‘1’ when FT121 goes to suspend (missing 3
continuous SOFs) or resumes from suspend. This bit will
be cleared after reading.
Table 6.9 Interrupt Register Byte 1
Bit
Symbol
Reset
Description
7-0
Reserved
00h
Reserved
Table 6.10 Interrupt Register Byte 2
Bit
Symbol
Reset
Description
0
Endpoint 3 Out
0
Interrupt for endpoint 3 OUT buffer. Cleared by Read
Last Transaction Status command.
1
Endpoint 3 In
0
Interrupt for endpoint 3 IN buffer. Cleared by Read Last
Transaction Status command.
2
Endpoint 4 Out
0
Interrupt for endpoint 4 OUT buffer. Cleared by Read
Last Transaction Status command.
3
Endpoint 4 In
0
Interrupt for endpoint 4 IN buffer. Cleared by Read Last
Transaction Status command.
Copyright © 2014 Future Technology Devices International Limited 26
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
Bit
Symbol
Reset
Description
4
Endpoint 5 Out
0
Interrupt for endpoint 5 OUT buffer. Cleared by Read
Last Transaction Status command.
5
Endpoint 5 In
0
Interrupt for endpoint 5 IN buffer. Cleared by Read Last
Transaction Status command.
6
Endpoint 6 Out
0
Interrupt for endpoint 6OUT buffer. Cleared by Read Last
Transaction Status command.
7
Endpoint 6 In
0
Interrupt for endpoint 6 IN buffer. Cleared by Read Last
Transaction Status command.
Table 6.11 Interrupt Register Byte 3 (for Enhanced Mode)
Bit
Symbol
Reset
Description
0
Endpoint 7 Out
0
Interrupt for endpoint 7 OUT buffer. Cleared by Read
Last Transaction Status command.
1
Endpoint 7 In
0
Interrupt for endpoint 7 IN buffer. Cleared by Read Last
Transaction Status command.
7-2
Reserved
0b’xxxxxx
Reserved
Table 6.12 Interrupt Register Byte 4 (for Enhanced Mode)
Copyright © 2014 Future Technology Devices International Limited 27
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
6.3.2 Select Endpoint
Command : 00-05h (00-0Fh for Enhanced Mode)
Data : Read 1 byte
Bit
Symbol
Reset
Description
0
Full/Empty
0
0: selected endpoint buffer is empty
1: selected endpoint buffer is not empty
1
Stall
0
0: selected endpoint is not stalled
1: selected endpoint is stalled
7-2
Reserved
0b’xxxxxx
Reserved
Table 6.13 Endpoint Status Register
6.3.3 Read Last Transaction Status
Command : 40-45h (40-4Fh for Enhanced Mode)
Data : Read 1 byte
Bit
Symbol
Reset
Description
0
Data Receive/Transmit
Success
0
0: indicate USB data receive or transmit not OK
1: indicate USB data receive or transmit OK
4-1
Error Code
0b’0000
Refer to Table 6.15
5
Setup Packet
0
0: indicate not a setup packet
1: indicate last received packet has a SETUP token
6
Data 0/1 Packet
0
0: packet has a DATA0 token
1: packet has a DATA1 token
7
Previous Status not
Read
0
0: previous transaction status was read
1: previous transaction status was not read
Table 6.14 Endpoint Last Transaction Status Register
Error Code
Result
0000
No error
0001
PID encoding error
Copyright © 2014 Future Technology Devices International Limited 28
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
Error Code
Result
0010
PID unknown
0011
Unexpected packet
0100
Token CRC error
0101
Data CRC error
0110
Time out error
0111
Reserved
1000
Unexpected EOP
1001
Packet NAKed
1010
Sent stall
1011
Buffer overflow
1101
Bit stuff error
1111
Wrong DATA PID
Table 6.15 Transaction error code
6.3.4 Read Endpoint Status
Command : 80-85h (80-8Fh for Enhanced Mode)
Data : Read 1 byte
Bit
Symbol
Reset
Description
1-0
Reserved
0b’00
Reserved
2
Setup packet
0
0: indicate not a setup packet
1: indicate last received packet has a SETUP token
4-3
Reserved
0b’xx
Reserved
5
Buffer 0 Full
0
0: buffer 0 is not filled up
1: buffer 0 is filled up
6
Buffer 1 Full
0
0: buffer 1 is not filled up
1: buffer 1 is filled up
Copyright © 2014 Future Technology Devices International Limited 29
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
Bit
Symbol
Reset
Description
7
Endpoint Stalled
0
0: endpoint is not stalled
1: endpoint is stalled
Table 6.16 Endpoint Buffer Status Register
6.3.5 Read Buffer
Command : E0h
Data : Read multiple bytes
The Read Buffer command is used to read the received packet from the selected endpoint OUT buffer.
The data in the endpoint buffer is organized as follows:
byte 0: length of payload packet, MSB(for default mode this byte is ignored)
byte 1: length of payload packet, LSB
byte 2: Payload packet byte 1
byte 3: Payload packet byte 2
byte n+1: Payload packet byte n (n = packet length)
6.3.6 Write Buffer
Command : F0h
Data : Write multiple bytes
The Write Buffer command is used to write payload packet to the selected endpoint IN buffer.
The data must be organized in the same way as described in the Read Buffer command. For default mode
byte 0 should always be set to 00h.
6.3.7 Clear Buffer
Command : F2h
Data : None
The Clear Buffer command should be issued after all data has been read out from the endpoint buffer.
This is to free the buffer to receive next packet from USB host.
6.3.8 Validate Buffer
Command : FAh
Copyright © 2014 Future Technology Devices International Limited 30
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
Data : None
The Validate Buffer command should be issued after all data has been written to the endpoint buffer. This
is to set the buffer full flag so that the packet can be sent to USB host when IN token arrives.
6.3.9 Set Endpoint Status
Command : 50-55h (50-5Fh for Enhanced Mode)
Data : Write 1 byte
Bit
Symbol
Reset
Description
0
Stall
0
0: Disable the endpoint STALL state.
1: Enable the endpoint STALL state.
For EP0 OUT (control OUT endpoint) the STALL state will
automatically be cleared by receiving a SETUP packet.
When this bit is written to ‘0’, the endpoint will
reinitialize. Any data in the endpoint buffer will be
flushed away, and the PID for next packet will carry
DATA0 flag.
7-1
Reserved
0b’xxxxxxx
Reserved
Table 6.17 Endpoint Control Register
6.3.10 Acknowledge Setup
Command : F1h
Data : None
When receiving a SETUP packet the FT121 will flush the IN buffer and disable the Validate Buffer and
Clear Buffer commands for both Control IN and Control OUT endpoints. The MCU shall read and process
the SETUP packet, and then issue the Acknowledge Setup command to re-enable the Validate Buffer and
Clear Buffer commands. The Acknowledge Setup command must be sent to both Control IN and Control
OUT endpoints.
6.4 General Commands
Copyright © 2014 Future Technology Devices International Limited 31
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
6.4.1 Read Current Frame Number
Command : F5h
Data : Read One or Two Bytes
Bit
Symbol
Reset
Description
7-0
Frame Number LSB
00h
Frame number for last received SOF, byte 1 (least
significant byte)
Table 6.18 Frame Number LSB Register
Bit
Symbol
Reset
Description
2-0
Frame Number MSB
0b’000
Frame number for last received SOF, byte 2 (Most
significant byte)
7-3
Reserved
0b’00000
Reserved
Table 6.19 Frame Number MSB Register
6.4.2 Send Resume
Command : F6h
Data : None
To perform remote-wakeup when suspended, the MCU needs to issue Send Resume command. The
FT121 will send an upstream resume signal for a period of 10 ms. If the clock is not running during
suspend, the MCU needs to wakeup FT121 by driving the SUSPEND pin to LOW, followed by the Send
Resume command.
6.4.3 Set 3-wire Mode
Command : E8h
Data : None
This command is used to enable the 3-wire SPI mode. Once enabled, the MOSI pin will become bi-
directional line and the MISO pin is not functional. Both SPI master and slave will drive data on the MOSI
line.
Copyright © 2014 Future Technology Devices International Limited 32
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
6.4.4 Read Vendor ID
Command : EBh (for Enhanced Mode)
Data : read 2 bytes
Read the 2 bytes Vendor ID. Shall return 0403h.
6.4.5 Read Product ID
Command : EAh (for Enhanced Mode)
Data : read 2 bytes
Read the 2 bytes Product ID. Shall return 6018h.
6.4.6 Read FTDI ID
Command : EDh (for Enhanced Mode)
Data : read 1 byte
Read the 1 byte FTDI ID. Shall return 11h.
6.4.7 Set IO Pad Drive Strength
Command : E9h
Data : Write 1 byte
Bit
Symbol
Reset
Description
1-0
Reserved
0b’00
Reserved, write to 0b’00
3-2
MISO, MOSI pins
0b’00
00: 4mA
01: 8mA
10: 12mA
11:16mA
5-4
INT_n, SUSPEND pins
0b’00
00: 4mA
01: 8mA
10: 12mA
11:16mA
7-6
Reserved
0b’00
Reserved, write to 0b’00
Table 6.20 IO Pad Drive Strength Register
Copyright © 2014 Future Technology Devices International Limited 33
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
7 Application Information
Figure 7-1 shows a reference application circuit for a USB bus-powered application. Figure 7-1 shows a
reference application circuit for a USB self-powered application.
FT121
1
2
3
4
5
SHIELD
Ferrite
Bead VCC
VOUT3V3
DM
DP
VCCIO
VCC
RESET_n
100nF
10nF
27R
27R
MCU
VCC3V3
VCC
SUSPEND
MOSI
MISO
SCLK
SS_n
INT_n
VBUS_S
GND
MOSI
MISO
SCLK
SS#
GPIO
GND
100nF
VCC3V3
BCD_n
GPIO
10k 10k
47pF
100nF 4.7uF
+
VCC
47pF
Figure 7-1 FT121 bus powered application
FT121
1
2
3
4
5
SHIELD
VCC
VOUT3V3
DM
DP
VCCIO
VCC
RESET_n
100nF
27R
27R
MCU
VCC
VCC
SUSPEND
MOSI
MISO
SCLK
SS_n
INT_n
VBUS_S
GND
GPIO
MOSI
MISO
SCLK
SS#
GPIO
GND
100nF
VCC3V3
470k
1M
BCD_n
47pF 47pF
10k 10k
VCC3V3
1M 1M
100nF 4.7uF
+
VCC
Figure 7-2 FT121 self powered application
Copyright © 2014 Future Technology Devices International Limited 34
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
8 Devices Characteristics and Ratings
8.1 Absolute Maximum Ratings
The absolute maximum ratings for the FT121 devices are as follows. These are in accordance with the
Absolute Maximum Rating System (IEC 60134). Exceeding these may cause permanent damage to the
device.
Parameter
Value
Unit
Storage Temperature
-65 to 150
°C
Floor Life (Out of Bag) At Factory Ambient
(30°C / 60% Relative Humidity)
168
(IPC/JEDEC J-STD-033A MSL Level 3
Compliant)*
Hours
Ambient Temperature (Power Applied)
-40 to 85
°C
Latch-up current
±200
mA
Electrostatic Discharge Voltage(ESD)
human body model(HBM)
±2
kV
Electrostatic Discharge Voltage(ESD)
machine model(MM)
±200
V
Electrostatic Discharge Voltage(ESD)
charged device model(CDM)
±500
V
VCC Supply Voltage
-0.5 to +6.0
V
DC Input Voltage DP and DM
-0.5 to +3.8
V
DC Input Voltage High Impedance
Bidirectional
-0.5 to + (VCC +0.5)
V
DC Input Voltage All Other Inputs
-0.5 to + (VCC +0.5)
V
DC Output Current Outputs
22
mA
Table 8.1 Absolute Maximum Ratings
* If devices are stored out of the packaging beyond this time limit the devices should be baked before
use. The devices should be ramped up to a temperature of +125°C and baked for up to 17 hours.
Copyright © 2014 Future Technology Devices International Limited 35
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
8.2 DC Characteristics
DC Characteristics (Ambient Temperature = -40°C to +85°C).
Parameter
Description
Minimum
Typical
Maximum
Units
Conditions
VCC1
VCC Operating Supply
Voltage
4.0
5.0
5.5
V
Normal Operation
VCC2
VCC Operating Supply
Voltage
3.0
3.3
3.6
V
Regulator by-pass
mode Operation
VCCIO
VCCIO Operating
Supply Voltage
1.65
3.6
V
Icc
Operating Supply
Current
3.9
mA
Normal Operation,
USB bus transmit
or receive
Icc2
Suspend Current
84
μA
USB Suspend,
Clock Running =
‘0’, excluding the
DP_Pullup current
VOUT3V3
3.3v regulator output
3.0
3.3
3.6
V
VCC=5V
Table 8.2 Operating Voltage and Current
Parameter
Description
Minimum
Typical
Maximum
Units
Conditions
Voh
Output Voltage High
2.9
V
I source = 4mA
Vol
Output Voltage Low
0.4
V
I sink = 4mA
Vih
Input Voltage High
2.0
V
Vil
Input Voltage Low
-
0.8
V
Table 8.3 digital I/O Pin Characteristics (VCCIO=+3.3V)
Parameter
Description
Minimum
Typical
Maximum
Units
Conditions
Voh
Output Voltage High
2.25
V
I source = 4mA
Vol
Output Voltage Low
0.4
V
I sink = 4mA
Vih
Input Voltage High
1.7
V
Vil
Input Voltage Low
-
0.7
V
Table 8.4 digital I/O Pin Characteristics (VCCIO=+2.5V)
Copyright © 2014 Future Technology Devices International Limited 36
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
Parameter
Description
Minimum
Typical
Maximum
Units
Conditions
Voh
Output Voltage High
1.62
V
I source = 4mA
Vol
Output Voltage Low
0.4
V
I sink = 4mA
Vih
Input Voltage High
1.17
V
Vil
Input Voltage Low
-
0.63
V
Table 8.5 digital I/O Pin Characteristics (VCCIO=+1.8V)
Parameter
Description
Minimum
Typical
Maximum
Units
Conditions
UVoh
I/O Pins Static Output
(High)
2.8
3.6
V
RL = 1.5kΩ to 3.6
V
UVol
I/O Pins Static Output
(Low)
-
0.3
V
RL = 15kΩ to GND
UVse
Single Ended Rx
Threshold
0.8
2.0
V
UCom
Differential Common
Mode
0.8
2.5
V
UVDif
Differential Input
Sensitivity
0.2
V
UDrvZ
Driver Output
Impedance
29
-
44
Including external
27 Ω ±1% series
resistor
Table 8.6 USB I/O Pin (DP, DM) Characteristics
8.3 AC Characteristics
Symbol
Parameter
VCCIO=3.3V
VCCIO=1.8V
Unit
Min
Max
Min
Max
t1
SCLK period
50
60
ns
t2
SCLK High period
25
30
ns
t3
SCLK Low period
25
30
ns
t4
SCLK driving edge to MOSI valid (3-wire mode)
SCLK driving edge to MISO valid (4-wire mode)
5
15
8
22
ns
t5
MOSI data setup time to sample SCLK edge
5
6
ns
t6
MOSI data hold time from sample SCLK edge
5
5
ns
Copyright © 2014 Future Technology Devices International Limited 37
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
Symbol
Parameter
VCCIO=3.3V
VCCIO=1.8V
Unit
Min
Max
Min
Max
t7
SS_n setup time to rising SCLK edge
2
2
ns
t8
SS_n hold time from falling sample SCLK edge
2
2
ns
Table 8.7 SPI slave timing
Note: All timing figures applied for both 4-wire and 3-wire modes.
Figure 8-1 SPI slave timing
Copyright © 2014 Future Technology Devices International Limited 38
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
9 Package Parameters
The FT121 is available in two different packages. The FT121T is the TSSOP-16 package option and the
FT121Q is the QFN-16 package option. The solder reflow profile for both packages is described in section
9.5.
9.1 TSSOP-16 Package Dimensions
Figure 9-1 TSSOP-16 Package Dimensions
The FT121T is supplied in a RoHS compliant 16 pin TSSOP package. The package is lead (Pb) free and
uses a ‘green’ compound. The package is fully compliant with European Union directive 2002/95/EC.
Copyright © 2014 Future Technology Devices International Limited 39
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
9.2 TSSOP-16 Package Markings
Figure 9-2 TSSOP-16 Package Markings
The date code format is YYWW where WW = 2 digit week number, YY = 2 digit year number.
Line 1 FTDI Logo
Line 2 Date Code, Revision
Line 3 FTDI Part Number
FT121T
YYWW-B
Copyright © 2014 Future Technology Devices International Limited 40
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
9.3 QFN-16 Package Dimensions
Figure 9-3 QFN-16 Package Dimensions
The FT121Q is supplied in a RoHS compliant leadless QFN-16 package. The package is lead ( Pb ) free,
and uses a ‘green’ compound. The package is fully compliant with European Union directive 2002/95/EC.
This package is nominally 3mm x 3mm. The solder pads are on a 0.50mm pitch. The above mechanical
drawing shows the QFN-16 package. All dimensions are in millimetres.
The center pads at the base of the FT121Q are internally connected to a power signal according to the
following table. These may be left unconnected or routed to the respective power signal:
Pad Number
Signal
Location top view
Location bottom view
17
Ground
Upper left
Upper right
18
VCCIO
Lower left
Lower right
19
VOUT3V3
Lower right
Lower left
20
VCC
Upper right
Upper left
Table 9.1 FT121Q Bottom Pad Assignments
Copyright © 2014 Future Technology Devices International Limited 41
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
9.4 QFN-16 Package Markings
Figure 9-4 QFN-16 Package Markings
The date code format is YYWW where WW = 2 digit week number, YY = 2 digit year number.
9.5 Solder Reflow Profile
The FT121 is supplied in Pb free TSSOP-16 and QFN-16 packages. The recommended solder reflow profile
for both package options is shown in Figure 9-5.
Figure 9-5 FT121 Solder Reflow Profile
Critical Zone: when
T is in the range
T to T
Temperature, T (Degrees C)
Time, t (seconds)
25 P
T = 25º C to T
tp
Tp
TL
t
Preheat
S
tL
Ramp Up Lp
Ramp
Down
T Max
S
T Min
S
Line 1 FTDI Logo
Line 2 Date Code, Revision
Line 3 FTDI Part Number
FT121Q
YYWW-B
Copyright © 2014 Future Technology Devices International Limited 42
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
The recommended values for the solder reflow profile are detailed in Table 9.2. Values are shown for both
a completely Pb free solder process (i.e. the FT121 is used with Pb free solder), and for a non-Pb free
solder process (i.e. the FT121 is used with non-Pb free solder).
Profile Feature
Pb Free Solder
Process
Non-Pb Free Solder Process
Average Ramp Up Rate (Ts to Tp)
3°C / second Max.
3°C / Second Max.
Preheat
- Temperature Min (Ts Min.)
- Temperature Max (Ts Max.)
- Time (ts Min to ts Max)
150°C
200°C
60 to 120 seconds
100°C
150°C
60 to 120 seconds
Time Maintained Above Critical
Temperature TL:
- Temperature (TL)
- Time (tL)
217°C
60 to 150 seconds
183°C
60 to 150 seconds
Peak Temperature (Tp)
260°C
240°C
Time within 5°C of actual Peak
Temperature (tp)
20 to 40 seconds
20 to 40 seconds
Ramp Down Rate
6°C / second Max.
6°C / second Max.
Time for T= 25°C to Peak Temperature,
Tp
8 minutes Max.
6 minutes Max.
Table 9.2 Reflow Profile Parameter Values
Copyright © 2014 Future Technology Devices International Limited 43
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
10 Contact Information
Head Office Glasgow, UK
Future Technology Devices International Limited
Unit 1, 2 Seaward Place, Centurion Business Park
Glasgow G41 1HH
United Kingdom
Tel: +44 (0) 141 429 2777
Fax: +44 (0) 141 429 2758
E-mail (Sales)
sales1@ftdichip.com
E-mail (Support)
support1@ftdichip.com
E-mail (General Enquiries)
admin1@ftdichip.com
Branch Office Taipei, Taiwan
Future Technology Devices International Limited
(Taiwan)
2F, No. 516, Sec. 1, NeiHu Road
Taipei 114
Taiwan , R.O.C.
Tel: +886 (0) 2 8791 3570
Fax: +886 (0) 2 8791 3576
E-mail (Sales)
tw.sales1@ftdichip.com
E-mail (Support)
tw.support1@ftdichip.com
E-mail (General Enquiries)
tw.admin1@ftdichip.com
Branch Office Tigard, Oregon, USA
Future Technology Devices International Limited
(USA)
7130 SW Fir Loop
Tigard, OR 97223
Tel: +1 (503) 547 0988
Fax: +1 (503) 547 0987
E-Mail (Sales)
us.sales@ftdichip.com
E-Mail (Support)
us.support@ftdichip.com
E-Mail (General Enquiries)
us.admin@ftdichip.com
Branch Office Shanghai, China
Future Technology Devices International Limited
(China)
Room 1103, No.666 West Huaihai Road,
Shanghai, 200052
China
Tel: +86 21 62351596
Fax: +86 21 62351595
E-mail (Sales)
cn.sales@ftdichip.com
E-mail (Support)
cn.support@ftdichip.com
E-mail (General Enquiries)
cn.admin@ftdichip.com
Branch Office Singapore
Future Technology Devices International Limited (Singapore)
178 Paya Lebar Road
#07-03/04/05
Singapore 409030
Tel: +65 6841 1174
Fax: +65 6841 6071
E-mail (Support)
support1@ftdichip.com
E-mail (General Enquiries)
admin1@ftdichip.com
Web Site
http://ftdichip.com
System and equipment manufacturers and designers are responsible to ensure that their systems, and any Future
Technology Devices International Ltd (FTDI) devices incorporated in their systems, meet all applicable safety, regulatory
and system-level performance requirements. All application-related information in this document (including application
descriptions, suggested FTDI devices and other materials) is provided for reference only. While FTDI has taken care to
assure it is accurate, this information is subject to customer confirmation, and FTDI disclaims all liability for system designs
and for any applications assistance provided by FTDI. Use of FTDI devices in life support and/or safety applications is
entirely at the user’s risk, and the user agrees to defend, indemnify and hold harmless FTDI from any and all damages,
claims, suits or expense resulting from such use. This document is subject to change without notice. No freedom to use
patents or other intellectual property rights is implied by the publication of this document. Neither the whole nor any part of
the information contained in, or the product described in this document, may be adapted or reproduced in any material or
electronic form without the prior written consent of the copyright holder. Future Technology Devices International Ltd, Unit
1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH, United Kingdom. Scotland Registered Company Number:
SC136640
Copyright © 2014 Future Technology Devices International Limited 44
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
Appendix A References
Useful Application Notes
http://www.ftdichip.com/Documents/AppNotes/AN_167_FT1248_Parallel_Serial_Interface_Basics.pdf
http://www.ftdichip.com/Support/Documents/TechnicalNotes/TN_100_USB_VID-PID_Guidelines.pdf
http://www.ftdichip.com/Support/Documents/AppNotes/AN_175_Battery%20Charging%20Over%20USB
%20with%20FTEX%20Devices.pdf
http://www.usb.org/developers/devclass_docs/BCv1.2_011912.zip
Appendix B - List of Figures and Tables
List of Figures
Figure 2-1 FT121 Block Diagram ..................................................................................................... 3
Figure 3-1 TSSOP-16 package schematic symbol .............................................................................. 6
Figure 3-2 QFN-16 package schematic symbol.................................................................................. 6
Figure 4-1 SPI access .................................................................................................................. 11
Figure 4-2 4-wire write operation .................................................................................................. 11
Figure 4-3 4-wire read operation .................................................................................................. 12
Figure 4-4 3-wire write operation .................................................................................................. 12
Figure 4-5 3-wire read operation .................................................................................................. 12
Figure 7-1 FT121 bus powered application ..................................................................................... 33
Figure 7-2 FT121 self powered application ..................................................................................... 33
Figure 8-1 SPI slave timing .......................................................................................................... 37
Figure 9-1 TSSOP-16 Package Dimensions ..................................................................................... 38
Figure 9-2 TSSOP-16 Package Markings ........................................................................................ 39
Figure 9-3 QFN-16 Package Dimensions ........................................................................................ 40
Figure 9-4 QFN-16 Package Markings ............................................................................................ 41
Figure 9-5 FT121 Solder Reflow Profile .......................................................................................... 41
List of Tables
Table 3.1 FT121 Pin Description ...................................................................................................... 7
Table 4.1 Interrupt modes ........................................................................................................... 10
Table 5.1 Endpoint configuration for EP0 and EP1 ........................................................................... 14
Table 5.2 Endpoint configuration for EP2 ....................................................................................... 14
Table 5.3 Example buffer configuration .......................................................................................... 15
Table 5.4 Endpoint Maximum Packet Size ...................................................................................... 16
Table 6.1 FT121 default command set ........................................................................................... 18
Table 6.2 enhanced command set ................................................................................................. 22
Table 6.3 Address Enable Register ................................................................................................ 22
Table 6.4 Endpoint Enable Register ............................................................................................... 22
Table 6.5 Configuration Register (Byte 1) ...................................................................................... 23
Table 6.6 Configuration Register (Byte 2) ...................................................................................... 23
Table 6.7 Interrupt Configuration Register ..................................................................................... 24
Copyright © 2014 Future Technology Devices International Limited 45
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
Table 6.8 Endpoint Configuration Register ...................................................................................... 24
Table 6.9 Interrupt Register Byte 1 ............................................................................................... 25
Table 6.10 Interrupt Register Byte 2 ............................................................................................. 25
Table 6.11 Interrupt Register Byte 3 (for Enhanced Mode) ............................................................... 26
Table 6.12 Interrupt Register Byte 4 (for Enhanced Mode) ............................................................... 26
Table 6.13 Endpoint Status Register .............................................................................................. 27
Table 6.14 Endpoint Last Transaction Status Register ...................................................................... 27
Table 6.15 Transaction error code ................................................................................................. 28
Table 6.16 Endpoint Buffer Status Register .................................................................................... 29
Table 6.17 Endpoint Control Register ............................................................................................ 30
Table 6.18 Frame Number LSB Register ......................................................................................... 31
Table 6.19 Frame Number MSB Register ........................................................................................ 31
Table 6.20 IO Pad Drive Strength Register ..................................................................................... 32
Table 8.1 Absolute Maximum Ratings ............................................................................................ 34
Table 8.2 Operating Voltage and Current ....................................................................................... 35
Table 8.3 digital I/O Pin Characteristics (VCCIO=+3.3V) .................................................................. 35
Table 8.4 digital I/O Pin Characteristics (VCCIO=+2.5V) .................................................................. 35
Table 8.5 digital I/O Pin Characteristics (VCCIO=+1.8V) .................................................................. 36
Table 8.6 USB I/O Pin (DP, DM) Characteristics .............................................................................. 36
Table 8.7 SPI slave timing ........................................................................................................... 37
Table 9.1 FT121Q Bottom Pad Assignments ................................................................................... 40
Table 9.2 Reflow Profile Parameter Values ..................................................................................... 42
Copyright © 2014 Future Technology Devices International Limited 46
Document No.: FT_000648
FT121 ENHANCED USB DEVICE CONTROLLER WITH SPI SLAVE IC
Datasheet Version 1.2
Clearance No.: FTDI# 312
Appendix C - Revision History
Document Title: DS_FT121
Document Reference No.: FT_000648
Clearance No.: FTDI# 312
Product Page: http://www.ftdichip.com/Products/ICs/FT121.htm
Document Feedback: Send Feedback
Version Draft Initial draft July 2012
Version 1.0 Initial release 1st October 2012
Version 1.1 Updated FT121Q bottom pad assignments 15th July 2013
Version 1.2 Updated release 23rd Mar 2015
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
FTDI:
FT121T-R FT121Q-R FT121T-U