Stacked Multi-Port Connector Tooling
Doc. No: ATS-622025290 Release Date: 09-13-13
UNCONTROLLED COPY
Page 1 of 3
Revision: C Revision Date: 06-05-17
zSFP+
CAGE
ASSEMBLY
PCB
2mm
MINIMUM
(BOTH SIDES)
KEEP OUT
ZONE
Figure 1
5mm
MINIMUM
2-by-12
Stacked Multi-Port
Removal Tool
Application Tooling
Specification Sheet
Order No. 62202-5290
FEATURES
Lightweight tool used in the removal of Stacked Multi-Port connectors in a PCB
Removes connector in a PCB without damage to the board
Use tool 62202-5280 for inserting connectors
SCOPE
Products: Small Form-factor Pluggable (zSFP+) 2-by-12 Multi-Port Connector with Press-fit PC Tails.
Connector
Series No.
Connector Order No.
170071
170071
-
1201
170071
-
1211
170071
-
1212
170071
-
1213
170071
-
1214
170071
-
1215
171224
171224
-
1201
171224
-
1209
171224
-
1211
171224
-
1212
171224
-
1213
171224
-
1214
171224
-
1215
171224
-
1230
171224
-
1231
171224
-
1241
171224
-
1242
171224
-
1250
171224
-
1260
171224
-
1261
172501
172501
-
1202
Notes:
1. See the following pages for tooling operation instructions.
2. These tools require a “Keep Out Zone” around the connector free of components. The right and left sides
should be 0.08” (2mm). The rear of the connector should be .197” (5.0mm). See Figure 1.
Stacked Multi-Port Connector Tooling
Doc. No: ATS-622025290 Release Date: 09-13-13
UNCONTROLLED COPY
Page 2 of 3
Revision: C Revision Date: 06-05-17
Figure
3
SUPPORT BLOCK
(INSERT)
CONNECTOR ASSEMBLY
(WITH THE FLANGE REMOVED)
SLIDE
PCB
CONNECTOR
ASSEMBLY
SUPPORT BLOCK
(FULLY SEATED)
Description
The following instructions are used for removing a 2-by-12
connector from a PCB:
Operation
1. Disassemble the two halves as delivered by unscrewing the
screws on the top of the upper tooling. See Figure 2.
2. Remove the upper tooling from the support tooling.
3. For the zSFP+ product, remove the flange, if applicable, from
the connector assembly to ensure full insertion of support
tooling into connector ports.
4. Insert the support block assembly into the connector assembly
until it is fully seated. See Figure 3.
5. Place the top removal assembly over the support block and the connector assembly, aligning the front tab of
the top removal assembly with the back edge of the support block. See Figure 4.
6. Place the washers and screws into the holes in the top removal assembly, and turn until seated on the top
plate using a 5/32” hex wrench to tighten the screws.
7. Tighten each screw, one turn in an alternating pattern, until the connector assembly is removed from the PCB.
See Figure 5.
Figure 2
REMOVE
UPPER
TOOLING
REMOVE THE
SCREWS AND
WASHERS
SUPPORT
TOOLING
Stacked Multi-Port Connector Tooling
Doc. No: ATS-622025290 Release Date: 09-13-13
UNCONTROLLED COPY
Page 3 of 3
Revision: C Revision Date: 06-05-17
Figure
4
PCB
TOP
REMOVAL
ASSEMBLY
SCREWS AND
WASHERS
SUPPORT
TOOLING
FRONT
TAB
PCB
Figure 5
SUPPORT
TOOLING
PCB
CONNECTOR ASSEMBLY
REMOVED
CONNECTOR ASSEMBLY
CAUTION: Molex application tooling specifications are valid only when used with Molex connectors and tooling.
Application Tooling Support
Phone: (402) 458-TOOL (8665)
E-Mail: applicationtooling@molex.com
Website: www.molex.com/applicationtooling
Molex is a registered trademark of Molex, LLC in the United States of America and may be registered in other countries; all other trademarks
listed herein belong to their respective owners.
