LT3008 Series 3A IQ, 20mA, 45V Low Dropout Linear Regulators FEATURES DESCRIPTION n The LT(R)3008 series are micropower, low dropout voltage (LDO) linear regulators. The devices supply 20mA output current with a dropout voltage of 300mV. No-load quiescent current is 3A. Ground pin current remains at less than 5% of output current as load increases. In shutdown, quiescent current is less than 1A. n n n n n n n n n n n n Ultralow Quiescent Current: 3A Input Voltage Range: 2.0V to 45V Output Current: 20mA Dropout Voltage: 300mV Adjustable Output (VADJ = VOUT(MIN) = 600mV) Fixed Output Voltages: 1.2V, 1.5V, 1.8V, 2.5V, 3.3V, 5V Output Tolerance: 2% Over Load, Line and Temperature Stable with Low ESR, Ceramic Output Capacitors (2.2F Minimum) Shutdown Current: <1A Current Limit Protection Reverse-Battery Protection Thermal Limit Protection TSOT-23 and 2mm x 2mm DFN Packages APPLICATIONS n n n n n n Automotive Low Current Battery-Powered Systems Keep-Alive Power Supplies Remote Monitoring Utility Meters Low Power Industrial Applications The LT3008 regulators optimize stability and transient response with low ESR ceramic capacitors, requiring a minimum of only 2.2F. The regulators do not require the addition of ESR as is common with other regulators. Internal protection circuitry includes current limiting, thermal limiting, reverse-battery protection and reversecurrent protection. The LT3008 series are ideal for applications that require moderate output drive capability coupled with ultralow standby power consumption. The device is available in fixed output voltages of 1.2V, 1.5V, 1.8V, 2.5V, 3.3V and 5V, and an adjustable version with an output voltage range of 0.6V to 44.5V. The LT3008 is available in the thermally enhanced 6-lead DFN and 8-lead TSOT-23 packages. L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. TYPICAL APPLICATION 3.3V, 20mA Supply with Shutdown Dropout Voltage/Quiescent Current 500 OUT 2.2F 1F VOUT 3.3V 20mA LT3008-3.3 SHDN SENSE GND 3008 TA01a DROPOUT VOLTAGE (mV) IN 6 ILOAD = 20mA DROPOUT VOLTAGE 400 350 5 4 300 250 IQ 3 200 2 150 100 QUIESCENT CURRENT (A) VIN 3.8V TO 45V 450 1 50 0 -50 -25 0 0 25 50 75 100 125 150 TEMPERATURE (C) 3008 TA01b 3008fc 1 LT3008 Series ABSOLUTE MAXIMUM RATINGS (Note 1) IN Pin Voltage .........................................................50V OUT Pin Voltage ......................................................50V Input-to-Output Differential Voltage ........................50V ADJ Pin Voltage ......................................................50V SENSE Pin Voltage ..................................................50V SHDN Pin Voltage (Note 8) .....................................50V Output Short-Circuit Duration .......................... Indefinite Operating Junction Temperature Range (Notes 2, 3) E, I Grade ...........................................-40C to 125C MP Grade...........................................-55C to 125C Storage Temperature Range...................-65C to 150C Lead Temperature: Soldering, 10 sec TS8 Package Only ............................................. 300C PIN CONFIGURATION TOP VIEW TOP VIEW 6 GND **SENSE/ADJ 1 OUT 2 7 OUT 3 SHDN GND GND GND 5 SHDN 4 IN 1 2 3 4 8 7 6 5 NC ADJ/SENSE** OUT IN TS8 PACKAGE 8-LEAD PLASTIC TSOT-23 DC PACKAGE 6-LEAD (2mm s 2mm) PLASTIC DFN TJMAX = 125C, JA = 65C/W TO 85C/W* EXPOSED PAD (PIN 7) IS GND, MUST BE SOLDERED TO PCB TJMAX = 125C, JA = 65C/W TO 85C/W* * See the Applications Information Section. ** SENSE for Fixed Voltage Output Versions. ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LT3008EDC#PBF LT3008EDC#TRPBF LDPS 6-Lead (2mm x 2mm) Plastic DFN -40C to 125C LT3008IDC#PBF LT3008IDC#TRPBF LDPS 6-Lead (2mm x 2mm) Plastic DFN -40C to 125C LT3008EDC-1.2#PBF LT3008EDC-1.2#TRPBF LFHC 6-Lead (2mm x 2mm) Plastic DFN -40C to 125C LT3008IDC-1.2#PBF LT3008IDC-1.2#TRPBF LFHC 6-Lead (2mm x 2mm) Plastic DFN -40C to 125C LT3008EDC-1.5#PBF LT3008EDC-1.5#TRPBF LFHF 6-Lead (2mm x 2mm) Plastic DFN -40C to 125C LT3008IDC-1.5#PBF LT3008IDC-1.5#TRPBF LFHF 6-Lead (2mm x 2mm) Plastic DFN -40C to 125C LT3008EDC-1.8#PBF LT3008EDC-1.8#TRPBF LFHH 6-Lead (2mm x 2mm) Plastic DFN -40C to 125C LT3008IDC-1.8#PBF LT3008IDC-1.8#TRPBF LFHH 6-Lead (2mm x 2mm) Plastic DFN -40C to 125C LT3008EDC-2.5#PBF LT3008EDC-2.5#TRPBF LFHK 6-Lead (2mm x 2mm) Plastic DFN -40C to 125C LT3008IDC-2.5#PBF LT3008IDC-2.5#TRPBF LFHK 6-Lead (2mm x 2mm) Plastic DFN -40C to 125C LT3008EDC-3.3#PBF LT3008EDC-3.3#TRPBF LFHN 6-Lead (2mm x 2mm) Plastic DFN -40C to 125C LT3008IDC-3.3#PBF LT3008IDC-3.3#TRPBF LFHN 6-Lead (2mm x 2mm) Plastic DFN -40C to 125C LT3008EDC-5#PBF LT3008EDC-5#TRPBF LFHQ 6-Lead (2mm x 2mm) Plastic DFN -40C to 125C LT3008IDC-5#PBF LT3008IDC-5#TRPBF LFHQ 6-Lead (2mm x 2mm) Plastic DFN -40C to 125C LT3008ETS8#PBF LT3008ETS8#TRPBF LTDSX 8-Lead Plastic TSOT-23 -40C to 125C 3008fc 2 LT3008 Series ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LT3008ITS8#PBF LT3008ITS8#TRPBF LTDSX 8-Lead Plastic TSOT-23 -40C to 125C LT3008MPTS8#PBF LT3008MPTS8#TRPBF LTDSX 8-Lead Plastic TSOT-23 -55C to 125C LT3008ETS8-1.2#PBF LT3008ETS8-1.2#TRPBF LTFHD 8-Lead Plastic TSOT-23 -40C to 125C LT3008ITS8-1.2#PBF LT3008ITS8-1.2#TRPBF LTFHD 8-Lead Plastic TSOT-23 -40C to 125C LT3008MPTS8-1.2#PBF LT3008MPTS8-1.2#TRPBF LTFHD 8-Lead Plastic TSOT-23 -55C to 125C LT3008ETS8-1.5#PBF LT3008ETS8-1.5#TRPBF LTFHG 8-Lead Plastic TSOT-23 -40C to 125C LT3008ITS8-1.5#PBF LT3008ITS8-1.5#TRPBF LTFHG 8-Lead Plastic TSOT-23 -40C to 125C LT3008MPTS8-1.5#PBF LT3008MPTS8-1.5#TRPBF LTFHG 8-Lead Plastic TSOT-23 -55C to 125C LT3008ETS8-1.8#PBF LT3008ETS8-1.8#TRPBF LTFHJ 8-Lead Plastic TSOT-23 -40C to 125C LT3008ITS8-1.8#PBF LT3008ITS8-1.8#TRPBF LTFHJ 8-Lead Plastic TSOT-23 -40C to 125C LT3008MPTS8-1.8#PBF LT3008MPTS8-1.8#TRPBF LTFHJ 8-Lead Plastic TSOT-23 -55C to 125C LT3008ETS8-2.5#PBF LT3008ETS8-2.5#TRPBF LTFHM 8-Lead Plastic TSOT-23 -40C to 125C LT3008ITS8-2.5#PBF LT3008ITS8-2.5#TRPBF LTFHM 8-Lead Plastic TSOT-23 -40C to 125C LT3008MPTS8-2.5#PBF LT3008MPTS8-2.5#TRPBF LTFHM 8-Lead Plastic TSOT-23 -55C to 125C LT3008ETS8-3.3#PBF LT3008ETS8-3.3#TRPBF LTFHP 8-Lead Plastic TSOT-23 -40C to 125C LT3008ITS8-3.3#PBF LT3008ITS8-3.3#TRPBF LTFHP 8-Lead Plastic TSOT-23 -40C to 125C LT3008MPTS8-3.3#PBF LT3008MPTS8-3.3#TRPBF LTFHP 8-Lead Plastic TSOT-23 -55C to 125C LT3008ETS8-5#PBF LT3008ETS8-5#TRPBF LTFHR 8-Lead Plastic TSOT-23 -40C to 125C LT3008ITS8-5#PBF LT3008ITS8-5#TRPBF LTFHR 8-Lead Plastic TSOT-23 -40C to 125C LT3008MPTS8-5#PBF LT3008MPTS8-5#TRPBF LTFHR 8-Lead Plastic TSOT-23 -55C to 125C LEAD BASED FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LT3008EDC LT3008EDC#TR LDPS 6-Lead (2mm x 2mm) Plastic DFN -40C to 125C LT3008IDC LT3008IDC#TR LDPS 6-Lead (2mm x 2mm) Plastic DFN -40C to 125C LT3008EDC-1.2 LT3008EDC-1.2#TR LFHC 6-Lead (2mm x 2mm) Plastic DFN -40C to 125C LT3008IDC-1.2 LT3008IDC-1.2#TR LFHC 6-Lead (2mm x 2mm) Plastic DFN -40C to 125C LT3008EDC-1.5 LT3008EDC-1.5#TR LFHF 6-Lead (2mm x 2mm) Plastic DFN -40C to 125C LT3008IDC-1.5 LT3008IDC-1.5#TR LFHF 6-Lead (2mm x 2mm) Plastic DFN -40C to 125C LT3008EDC-1.8 LT3008EDC-1.8#TR LFHH 6-Lead (2mm x 2mm) Plastic DFN -40C to 125C LT3008IDC-1.8 LT3008IDC-1.8#TR LFHH 6-Lead (2mm x 2mm) Plastic DFN -40C to 125C LT3008EDC-2.5 LT3008EDC-2.5#TR LFHK 6-Lead (2mm x 2mm) Plastic DFN -40C to 125C LT3008IDC-2.5 LT3008IDC-2.5#TR LFHK 6-Lead (2mm x 2mm) Plastic DFN -40C to 125C LT3008EDC-3.3 LT3008EDC-3.3#TR LFHN 6-Lead (2mm x 2mm) Plastic DFN -40C to 125C LT3008IDC-3.3 LT3008IDC-3.3#TR LFHN 6-Lead (2mm x 2mm) Plastic DFN -40C to 125C LT3008EDC-5 LT3008EDC-5#TR LFHQ 6-Lead (2mm x 2mm) Plastic DFN -40C to 125C LT3008IDC-5 LT3008IDC-5#TR LFHQ 6-Lead (2mm x 2mm) Plastic DFN -40C to 125C LT3008ETS8 LT3008ETS8#TR LTDSX 8-Lead Plastic TSOT-23 -40C to 125C LT3008ITS8 LT3008ITS8#TR LTDSX 8-Lead Plastic TSOT-23 -40C to 125C LT3008MPTS8 LT3008MPTS8#TR LTDSX 8-Lead Plastic TSOT-23 -55C to 125C LT3008ETS8-1.2 LT3008ETS8-1.2#TR LTFHD 8-Lead Plastic TSOT-23 -40C to 125C LT3008ITS8-1.2 LT3008ITS8-1.2#TR LTFHD 8-Lead Plastic TSOT-23 -40C to 125C LT3008MPTS8-1.2 LT3008MPTS8-1.2#TR LTFHD 8-Lead Plastic TSOT-23 -55C to 125C 3008fc 3 LT3008 Series ORDER INFORMATION LEAD BASED FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LT3008ETS8-1.5 LT3008ETS8-1.5#TR LTFHG 8-Lead Plastic TSOT-23 -40C to 125C LT3008ITS8-1.5 LT3008ITS8-1.5#TR LTFHG 8-Lead Plastic TSOT-23 -40C to 125C LT3008MPTS8-1.5 LT3008MPTS8-1.5#TR LTFHG 8-Lead Plastic TSOT-23 -55C to 125C LT3008ETS8-1.8 LT3008ETS8-1.8#TR LTFHJ 8-Lead Plastic TSOT-23 -40C to 125C LT3008ITS8-1.8 LT3008ITS8-1.8#TR LTFHJ 8-Lead Plastic TSOT-23 -40C to 125C LT3008MPTS8-1.8 LT3008MPTS8-1.8#TR LTFHJ 8-Lead Plastic TSOT-23 -55C to 125C LT3008ETS8-2.5 LT3008ETS8-2.5#TR LTFHM 8-Lead Plastic TSOT-23 -40C to 125C LT3008ITS8-2.5 LT3008ITS8-2.5#TR LTFHM 8-Lead Plastic TSOT-23 -40C to 125C LT3008MPTS8-2.5 LT3008MPTS8-2.5#TR LTFHM 8-Lead Plastic TSOT-23 -55C to 125C LT3008ETS8-3.3 LT3008ETS8-3.3#TR LTFHP 8-Lead Plastic TSOT-23 -40C to 125C LT3008ITS8-3.3 LT3008ITS8-3.3#TR LTFHP 8-Lead Plastic TSOT-23 -40C to 125C LT3008MPTS8-3.3 LT3008MPTS8-3.3#TR LTFHP 8-Lead Plastic TSOT-23 -55C to 125C LT3008ETS8-5 LT3008ETS8-5#TR LTFHR 8-Lead Plastic TSOT-23 -40C to 125C LT3008ITS8-5 LT3008ITS8-5#TR LTFHR 8-Lead Plastic TSOT-23 -40C to 125C LT3008MPTS8-5 LT3008MPTS8-5#TR LTFHR 8-Lead Plastic TSOT-23 -55C to 125C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TJ = 25C. (Note 2) PARAMETER CONDITIONS MIN l 2 LT3008-1.2: VIN = 2V, ILOAD = 100A 2V < VIN < 45V, 1A < ILOAD < 20mA l 1.188 1.176 LT3008-1.5: VIN = 2.05V, ILOAD = 100A 2.05V < VIN < 45V, 1A < ILOAD < 20mA l LT3008-1.8: VIN = 2.35V, ILOAD = 100A 2.35V < VIN < 45V, 1A < ILOAD < 20mA TYP MAX UNITS 45 V 1.2 1.2 1.212 1.224 V V 1.485 1.47 1.5 1.5 1.515 1.53 V V l 1.782 1.764 1.8 1.8 1.818 1.836 V V LT3008-2.5: VIN = 3.05V, ILOAD = 100A 3.05V < VIN < 45V, 1A < ILOAD < 20mA l 2.475 2.45 2.5 2.5 2.525 2.55 V V LT3008-3.3: VIN = 3.85V, ILOAD = 100A 3.85V < VIN < 45V, 1A < ILOAD < 20mA l 3.267 3.234 3.3 3.3 3.333 3.366 V V LT3008-5: VIN = 5.55V, ILOAD = 100A 5.55V < VIN < 45V, 1A < ILOAD < 20mA l 4.95 4.9 5 5 5.05 5.1 V V ADJ Pin Voltage (Notes 3, 4) VIN = 2V, ILOAD = 100A 2V < VIN < 45V, 1A < ILOAD < 20mA l 594 588 600 600 606 612 mV mV Line Regulation (Note 3) LT3008-1.2: VIN = 2V to 45V, ILOAD = 1mA LT3008-1.5: VIN = 2.05V to 45V, ILOAD = 1mA LT3008-1.8: VIN = 2.35V to 45V, ILOAD = 1mA LT3008-2.5: VIN = 3.05V to 45V, ILOAD = 1mA LT3008-3.3: VIN = 3.85V to 45V, ILOAD = 1mA LT3008-5: VIN = 5.55V to 45V, ILOAD = 1mA LT3008: VIN = 2V to 45V, ILOAD = 1mA l l l l l l l 1.2 1.5 1.8 2.5 3.3 5 0.6 6 7.5 9 12.5 16.5 25 3 mV mV mV mV mV mV mV Operating Voltage Regulated Output Voltage 3008fc 4 LT3008 Series ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TJ = 25C. (Note 2) PARAMETER CONDITIONS Load Regulation (Note 3) LT3008-1.2: VIN = 2V, ILOAD = 1A to 10mA VIN = 2V, ILOAD = 1A to 20mA Dropout Voltage VIN = VOUT(NOMINAL) (Notes 5, 6) MIN TYP MAX l l 0.8 1 4 10 mV mV LT3008-1.5: VIN = 2.05V, ILOAD = 1A to 10mA VIN = 2.05V, ILOAD = 1A to 20mA l l 1 1.3 5 13 mV mV LT3008-1.8: VIN = 2.35V, ILOAD = 1A to 10mA VIN = 2.35V, ILOAD = 1A to 20mA l l 1.2 1.5 6 15 mV mV LT3008-2.5: VIN = 3.05V, ILOAD = 1A to 10mA VIN = 3.05V, ILOAD = 1A to 20mA l l 1.7 2.1 8.3 21 mV mV LT3008-3.3: VIN = 3.85V, ILOAD = 1A to 10mA VIN = 3.85V, ILOAD = 1A to 20mA l l 2.2 2.8 11 28 mV mV LT3008-5: VIN = 5.55V, ILOAD = 1A to 10mA VIN = 5.55V, ILOAD = 1A to 20mA l l 3.4 4.2 17 42 mV mV LT3008: VIN = 2V, ILOAD = 1A to 10mA VIN = 2V, ILOAD = 1A to 20mA l l 0.4 0.5 2 5 mV mV 115 180 250 mV mV 170 250 350 mV mV 270 340 470 mV mV 300 365 500 mV mV 6 A A 6 12 50 500 1200 A A A A A ILOAD = 100A ILOAD = 100A l ILOAD = 1mA ILOAD = 1mA l ILOAD = 10mA ILOAD = 10mA l ILOAD = 20mA ILOAD = 20mA l ILOAD = 0A ILOAD = 0A l GND Pin Current VIN = VOUT(NOMINAL) + 0.5V (Notes 6, 7) ILOAD = 0A ILOAD = 100A ILOAD = 1mA ILOAD = 10mA ILOAD = 20mA l l l l l Output Voltage Noise (Note 9) COUT = 2.2F, ILOAD = 20mA, BW = 10Hz to 100kHz Quiescent Current (Notes 6, 7) VOUT = Off to On VOUT = On to Off l l VSHDN = 0V, VIN = 45V VSHDN = 45V, VIN = 45V l l Quiescent Current in Shutdown VIN = 6V, VSHDN = 0V l Ripple Rejection (Note 3) VIN - VOUT = 2V, VRIPPLE = 0.5VP-P, fRIPPLE = 120Hz, ILOAD = 20mA LT3008 LT3008-1.2 LT3008-1.5 LT3008-1.8 LT3008-2.5 LT3008-3.3 LT3008-5 SHDN Pin Current 3 6 21 160 350 92 ADJ Pin Bias Current Shutdown Threshold 3 UNITS VRMS -10 0.4 10 nA 0.67 0.61 1.5 0.25 V V 1 2 A A <1 A 0.65 58 54 53 52 49 47 42 70 66 65 64 61 59 54 dB dB dB dB dB dB dB 3008fc 5 LT3008 Series ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TJ = 25C. (Note 2) PARAMETER CONDITIONS Current Limit VIN = 45V, VOUT = 0 VIN = VOUT(NOMINAL) + 1V, VOUT = - 5% l Input Reverse-Leakage Current VIN = -45V, VOUT = 0 l Reverse-Output Current VOUT = 1.2V, VIN = 0 Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LT3008 regulators are tested and specified under pulse load conditions such that TJ TA. The LT3008E is guaranteed to meet performance specifications from 0C to 125C operating junction temperature. Specifications over the -40C to 125C operating junction temperature range are assured by design, characterization and correlation with statistical process controls. The LT3008I is guaranteed over the full - 40C to 125C operating junction temperature range. The LT3008MP is 100% tested and guaranteed over the -55C to 125C operating junction temperature range. Note 3: The LT3008 adjustable version is tested and specified for these conditions with the ADJ pin connected to the OUT pin. Note 4: Operating conditions are limited by maximum junction temperature. The regulated output voltage specification will not apply for all possible combinations of input voltage and output current. When operating at the maximum input voltage, the output current range must be limited. When operating at the maximum output current, the input voltage must be limited. MIN TYP MAX 75 UNITS mA mA 22 1 30 A 0.6 10 A Note 5: Dropout voltage is the minimum input to output voltage differential needed to maintain regulation at a specified output current. In dropout, the output voltage equals (VIN - VDROPOUT). For the LT3008-1.2 and LT30081.5, dropout voltage will be limited by the minimum input voltage. Note 6: To satisfy minimum input voltage requirements, the LT3008 adjustable version is tested and specified for these conditions with an external resistor divider (61.9k bottom, 280k top) which sets VOUT to 3.3V. The external resistor divider adds 9.69A of DC load on the output. This external current is not factored into GND pin current. Note 7: GND pin current is tested with VIN = VOUT(NOMINAL) + 0.55V and a current source load. GND pin current will increase in dropout. For the fixed output voltage versions, an internal resistor divider will add about 1A to the GND pin current. See the GND Pin Current curves in the Typical Performance Characteristics section. Note 8: The SHDN pin can be driven below GND only when tied to the IN pin directly or through a pull-up resistor. If the SHDN pin is driven below GND by more than -0.3V while IN is powered, the output will turn on. Note 9: Output noise is listed for the adjustable version with the ADJ pin connected to the OUT pin. See the RMS Output Noise vs Load Current curve in the Typical Performance Characteristics Section. 3008fc 6 LT3008 Series TYPICAL PERFORMANCE CHARACTERISTICS Dropout Voltage Dropout Voltage 350 300 DROPOUT VOLTAGE (mV) DROPOUT VOLTAGE (mV) TJ = 125C TJ = 25C 250 200 150 100 2 400 1.8 350 200 100A 100 0 6 8 10 12 14 16 18 20 OUTPUT CURRENT (mA) 1mA 150 0 4 10mA 250 50 2 20mA 300 50 0 Minimum Input Voltage 450 -50 -25 1.4 1.2 1 0.8 0.6 0.4 0 25 50 75 0 100 125 150 -50 -25 1.224 IL = 100A 1.220 1.530 ILOAD = 100A 1.525 1.520 1.212 1.515 0.596 0.594 OUTPUT VOLTAGE (V) 1.216 0.598 1.208 1.204 1.200 1.196 1.192 1.188 1.510 1.505 1.500 1.495 1.490 1.485 1.184 1.480 0.590 1.180 1.176 -50 -25 1.475 1.470 -50 -25 0 25 50 75 100 125 150 0 TEMPERATURE (C) 25 100 125 150 ILOAD = 100A 0.592 0.588 -50 -25 75 Output Voltage LT3008-1.5 0.606 0.600 50 3008 G03 0.608 0.602 25 TEMPERATURE (C) Output Voltage LT3008-1.2 0.604 0 3008 G02 OUTPUT VOLTAGE (V) ADJ PIN VOLTAGE (V) 1.6 TEMPERATURE (C) ADJ Pin Voltage 0.610 ILOAD = 20mA 0.2 3008 G01 0.612 MINIMUM INPUT VOLTAGE (V) 450 400 TA = 25C, unless otherwise noted. 50 75 TEMPERATURE (C) 100 125 150 0 25 50 75 TEMPERATURE (C) 3008 G05 100 125 150 3008 G06 3008 G04 Output Voltage LT3008-1.8 1.830 2.550 ILOAD = 100A 2.540 1.812 1.806 1.800 1.794 1.788 1.782 3.355 3.344 2.520 2.510 2.500 2.490 2.480 2.470 1.776 1.770 1.764 -50 -25 3.366 ILOAD = 100A 2.530 1.816 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 1.824 Output Voltage LT3008-3.3 OUTPUT VOLTAGE (V) 1.836 Output Voltage LT3008-2.5 0 25 50 75 TEMPERATURE (C) 100 125 150 3008 G07 3.333 3.322 3.311 3.300 3.289 3.278 3.267 3.256 2.460 2.450 -50 -25 ILOAD = 100A 3.245 0 25 50 75 TEMPERATURE (C) 100 125 150 3008 G08 3.234 -50 -25 0 25 50 75 TEMPERATURE (C) 100 125 150 3008 G09 3008fc 7 LT3008 Series TYPICAL PERFORMANCE CHARACTERISTICS Output Voltage LT3008-5 ADJ Pin Bias Current 5.100 Adjustable Quiescent Current 10 ILOAD = 100A 6 8 5.050 5.025 5.000 4.975 4.950 4.925 5 6 QUIESCENT CURRENT (A) ADJ PIN BIAS CURRENT (nA) 5.075 OUTPUT VOLTAGE (V) TA = 25C, unless otherwise noted. 4 2 0 -2 -4 -6 4 3 2 1 -8 4.900 -50 -25 0 25 50 75 -10 100 125 150 TEMPERATURE (C) -50 -25 0 25 50 75 0 -50 -25 100 125 150 0 TEMPERATURE (C) 3008 G10 25 50 75 100 125 150 TEMPERATURE (C) 3008 G05 GND Pin Current LT3008-1.2 Quiescent Current QUIESCENT CURRENT (A) 24 21 18 GND PIN CURRENT (A) LT3008-1.2 LT3008-1.5 LT3008-1.8 LT3008-2.5 LT3008-3.3 LT3008-5 27 15 12 9 500 500 450 450 400 400 350 250 200 100 50 0 0 3 4 5 6 7 8 RL = 120, IL = 10mA 150 3 2 RL = 60, IL = 20mA 300 6 1 GND Pin Current LT3008-1.5 GND PIN CURRENT (A) 30 0 3008 G06 9 10 350 RL = 75, IL = 20mA 300 250 200 RL = 150, IL = 10mA 150 100 RL = 12k, IL = 100A RL = 15k, IL = 100A 50 RL = 1.2k, IL = 1mA RL = 1.5k, IL = 1mA 0 0 1 2 INPUT VOLTAGE (V) 3 4 5 6 7 INPUT VOLTAGE (V) 8 9 10 0 1 2 3 4 5 6 7 INPUT VOLTAGE (V) 8 3008 G14 9 10 3008 G15 3008 G13 GND Pin Current LT3008-2.5 GND Pin Current LT3008-3.3 500 500 450 450 450 400 400 400 350 RL = 90, IL = 20mA 300 250 200 RL = 180, IL = 10mA 150 100 RL = 125, IL = 20mA 300 250 200 RL = 250, IL = 10mA 150 100 RL = 18k, IL = 100A 50 350 0 RL = 2.5k, IL = 1mA 0 0 1 2 3 4 5 6 7 INPUT VOLTAGE (V) 8 9 10 3008 G16 RL = 165, IL = 20mA 350 300 250 200 RL = 330, IL = 10mA 150 100 RL = 25k, IL = 100A 50 RL = 1.8k, IL = 1mA GND PIN CURRENT (A) 500 GND PIN CURRENT (A) GND PIN CURRENT (A) GND Pin Current LT3008-1.8 RL = 33k, IL = 100A 50 RL = 3.3k, IL = 1mA 0 0 1 2 3 4 5 6 7 INPUT VOLTAGE (V) 8 9 10 3008 G17 0 1 2 3 4 5 6 7 INPUT VOLTAGE (V) 8 9 10 3008 G18 3008fc 8 LT3008 Series TYPICAL PERFORMANCE CHARACTERISTICS GND Pin Current LT3008-5 TA = 25C, unless otherwise noted. SHDN Pin Thresholds GND Pin Current vs ILOAD 1000 500 450 VIN = 3.8V VOUT = 3.3V 300 250 200 RL = 500, IL = 10mA 150 SHDN PIN THRESHOLD (V) RL = 250, IL = 20mA 350 GND CURRENT (A) GND PIN CURRENT (A) 400 100 10 RL = 50k, IL = 100A 100 50 RL = 5k, IL = 1mA 0 0 1 3 4 5 6 7 INPUT VOLTAGE (V) 2 8 9 1 0.001 10 0.01 0.1 1 10 100 1.5 1.4 1.3 1.2 1.1 1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 -50 -25 OFF TO ON ON TO OFF 0 LOAD (mA) 3008 G19 25 50 75 100 125 150 TEMPERATURE (C) 3008 G21 3008 G20 SHDN Pin Input Current Current Limit 100 1.8 1.8 90 1.6 80 1.6 1.4 1.2 1 0.8 0.6 0.4 0.2 5 10 15 20 25 30 35 SHDN PIN VOLTAGE (V) 1.2 1 VSHDN = 45V 0.8 0.6 40 45 INPUT RIPPLE REJECTION (dB) REVERSE OUTPUT CURRENT (A) 30 25 20 15 ADJ 0 -50 -25 OUT 0 25 50 75 100 125 150 TEMPERATURE (C) 3008 G25 25 50 75 100 125 150 TEMPERATURE (C) Input Ripple Rejection VIN = 2.1V + 50mVRMS VOUT = 600mV ILOAD = 20mA 80 35 0 3008 G24 Input Ripple Rejection 90 40 5 0 -50 -25 25 50 75 100 125 150 TEMPERATURE (C) 3008 G23 OUT = ADJ = 1.2V IN = SHDN = GND 10 30 10 Reverse-Output Current 45 VIN = 2V 40 20 3008 G22 50 60 50 0.2 0 VIN = 45V 70 0.4 70 60 50 40 10F 30 20 2.2F 10 100 1000 10000 70 60 50 40 30 20 10 10 0 80 INPUT RIPPLE REJECTION (dB) 0 1.4 0 -50 -25 0 CURRENT LIMIT (mA) 2 SHDN PIN INPUT CURRENT (A) SHDN PIN INPUT CURRENT (A) SHDN Pin Input Current 2 100000 1000000 FREQUENCY (Hz) 3008 G26 VIN = VOUT (NOMINAL) + 2V + 0.5VP-P RIPPLE AT f = 120Hz ILOAD = 20mA 0 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (C) 3008 G27 3008fc 9 LT3008 Series TYPICAL PERFORMANCE CHARACTERISTICS $IL = 1A to 20mA VOUT = 600mV VIN = 2V 4 LOAD REGULATION (mV) OUTPUT NOISE SPECTRAL DENSITY (V Hz) 5 4.5 3.5 3 2.5 2 1.5 1 0.5 0 -50 -25 0 RMS Output Noise vs Load Current Output Noise Spectral Density 25 50 75 100 125 150 TEMPERATURE (C) 100 COUT = 2.2F ILOAD = 20mA 5V 3.3V 2.5V 1.8V 1.5V 1V 0.6V 10 1 0.1 10 100 1k 10k FREQUENCY (Hz) 100k 500 450 5V 350 3.3V 300 2.5V 250 1.8V 200 1.5V 150 100 1.2V 50 0.6V 0 0.001 0.01 0.1 1 3008 G30 Transient Response Transient Response IOUT = 1mA TO 20mA VIN = 5.5V VOUT = 5V COUT = 2.2F 100 10 ILOAD (mA) 3008 G29 3008 G28 Transient Response (Load Dump) IOUT = 1mA TO 20mA VIN = 5.5V VOUT = 5V COUT = 10F VOUT 50mV/DIV COUT = 10F 400 OUTPUT NOISE (VRMS) Load Regulation TA = 25C, unless otherwise noted. VOUT 50mV/DIV VOUT 50mV/DIV IOUT 20mA/DIV 500s/DIV 3008 G31 45V VOUT = 5V IOUT = 20mA COUT = 4.7F VIN 10V/DIV IOUT 20mA/DIV 500s/DIV 3008 G32 1ms/DIV 12V 3008 G33 3008fc 10 LT3008 Series PIN FUNCTIONS (TSOT-23/DFN) SHDN (Pin 1/Pin 5): Shutdown. Pulling the SHDN pin low puts the LT3008 into a low power state and turns the output off. If unused, tie the SHDN pin to VIN. The LT3008 does not function if the SHDN pin is not connected. The SHDN pin cannot be driven below GND unless tied to the IN pin. If the SHDN pin is driven below GND while IN is powered, the output will turn on. SHDN pin logic cannot be referenced to a negative rail. GND (Pins 2, 3, 4/Pin 6): Ground. Connect the bottom of the resistor divider that sets output voltage directly to GND for the best regulation. IN (Pin 5/Pin 4): Input. The IN pin supplies power to the device. The LT3008 requires a bypass capacitor at IN if the device is more than six inches away from the main input filter capacitor. In general, the output impedance of a battery rises with frequency, so it is advisable to include a bypass capacitor in battery-powered circuits. A bypass capacitor in the range of 0.1F to 10F will suffice. The LT3008 withstands reverse voltages on the IN pin with respect to ground and the OUT pin. In the case of a reversed input, which occurs with a battery plugged in backwards, the LT3008 acts as if a blocking diode is in series with its input. No reverse current flows into the LT3008 and no reverse voltage appears at the load. The device protects both itself and the load. OUT (Pin 6/Pins 2, 3): Output. This pin supplies power to the load. Use a minimum output capacitor of 2.2F to prevent oscillations. Large load transient applications require larger output capacitors to limit peak voltage transients. See the Applications Information section for more information on output capacitance and reverse-output characteristics. ADJ (Pin 7/Pin 1): Adjust. This pin is the error amplifier's inverting terminal. Its 400pA typical input bias current flows out of the pin (see curve of ADJ Pin Bias Current vs Temperature in the Typical Performance Characteristics section). The ADJ pin voltage is 600mV referenced to GND and the output voltage range is 600mV to 44.5V. NC (Pin 8, TSOT-23 Package Only): No Connect. Pin 8 is an NC pin in the TSOT-23 package. This pin is not tied to any internal circuitry. It may be floated, tied to VIN or tied to GND. GND (Exposed Pad Pin 7, DFN Package Only): Ground. The exposed pad (backside) of the DFN package is an electrical connection to GND. To ensure optimum performance, solder Pin 7 to the PCB and tie directly to Pin 6. SENSE (Pin 7/Pin 1): Sense. For fixed voltage versions of the LT3008 (LT3008-1.2, LT3008-1.5, LT3008-1.8, LT30082.5, LT3008-3.3, LT3008-5), the SENSE pin is the input to the error amplifier. Optimum regulation is obtained at the point where the SENSE pin is connected to the OUT pin of the regulator. In critical applications, small voltage drops are caused by the resistance (RP) of PC traces between the regulator and the load. These may be eliminated by connecting the SENSE pin to the output at the load as shown in Figure 1 (Kelvin Sense Connection). Note that the voltage drop across the external PC traces add to the dropout voltage of the regulator. The SENSE pin bias current is 1A at the nominal rated output voltage. The SENSE pin can be pulled below ground (as in a dual supply system where the regulator load is returned to a negative supply) and still allow the device to start and operate. RP IN OUT LT3008 + VIN SHDN + SENSE LOAD GND RP 3008 F01 Figure 1. Kelvin Sense Connection 3008fc 11 LT3008 Series APPLICATIONS INFORMATION The LT3008 is a low dropout linear regulator with ultralow quiescent current and shutdown. Quiescent current is extremely low at 3A and drops well below 1A in shutdown. The device supplies up to 20mA of output current. Dropout voltage at 20mA is typically 300mV. The LT3008 incorporates several protection features, making it ideal for use in battery-powered systems. The device protects itself against both reverse-input and reverse-output voltages. In battery backup applications, where a backup battery holds up the output when the input is pulled to ground, the LT3008 acts as if a blocking diode is in series with its output and prevents reverse current flow. In applications where the regulator load returns to a negative supply, the output can be pulled below ground by as much as 50V without affecting start-up or normal operation. Adjustable Operation The LT3008 has an output voltage range of 0.6V to 44.5V. Figure 2 shows that output voltage is set by the ratio of two external resistors. The IC regulates the output to maintain the ADJ pin voltage at 600mV referenced to ground. The current in R1 equals 600mV/R1 and the current in R2 is the current in R1 minus the ADJ pin bias current. The ADJ pin bias current, typically 400pA at 25C, flows out of the pin. Calculate the output voltage using the formula in Figure 2. An R1 value of 619k sets the divider current to 0.97A. Do not make R1's value any greater than 619k to minimize output voltage errors due to the ADJ pin bias current and VOUT = 600mV * (1 + R2/R1) - (IADJ * R2) VADJ = 600mV IADJ = 0.4nA at 25C OUTPUT RANGE = 0.6V to 44.5V to insure stability under minimum load conditions. In shutdown, the output turns off and the divider current is zero. Curves of ADJ Pin Voltage vs Temperature and ADJ Pin Bias Current vs Temperature appear in the Typical Performance Characteristics. Specifications for output voltages greater than 0.6V are proportional to the ratio of the desired output voltage to 0.6V: VOUT/0.6V. For example, load regulation for an output current change of 100A to 20mA is -0.5mV typical at VOUT = 0.6V. At VOUT = 5V, load regulation is: 5V * (-0.5mV) = -4.17mV 0.6V Table 1 shows resistor divider values for some common output voltages with a resistor divider current of about 1A. Table 1. Output Voltage Resistor Divider Values VOUT R1 R2 1V 604k 402k 1.2V 590k 590k 1.5V 590k 887k 1.8V 590k 1.18M 2.5V 590k 1.87M 3V 590k 2.37M 3.3V 619k 2.8M 5V 590k 4.32M IN VIN VOUT OUT LT3008 SHDN GND R2 ADJ R1 3008 F02 Figure 2. Adjustable Operation 3008fc 12 LT3008 Series APPLICATIONS INFORMATION Because the ADJ pin is relatively high impedance (depending on the resistor divider used), stray capacitances at this pin should be minimized. Special attention should be given to any stray capacitances that can couple external signals onto the ADJ pin, producing undesirable output transients or ripple. Extra care should be taken in assembly when using high valued resistors. Small amounts of board contamination can lead to significant shifts in output voltage. Appropriate post-assembly board cleaning measures should be implemented to prevent board contamination. If the board is to be subjected to humidity cycling or if board cleaning measures cannot be guaranteed, consideration should be given to using resistors an order of magnitude smaller than in Table 1 to prevent contamination from causing unwanted shifts in the output voltage. A fixed voltage option in the LT3008 series will not need these special considerations. Output Capacitance and Transient Response The LT3008 is stable with a wide range of output capacitors. The ESR of the output capacitor affects stability, most notably with small capacitors. Use a minimum output capacitor of 2.2F with an ESR of 3 or less to prevent oscillations. The LT3008 is a micropower device and output load transient response is a function of output capacitance. Larger values of output capacitance decrease the peak deviations and provide improved transient response for larger load current changes. Give extra consideration to the use of ceramic capacitors. Manufacturers make ceramic capacitors with a variety of dielectrics, each with different behavior across temperature and applied voltage. The most common dielectrics are specified with EIA temperature characteristic codes of Z5U, Y5V, X5R and X7R. The Z5U and Y5V dielectrics provide high C-V products in a small package at low cost, but exhibit strong voltage and temperature coefficients as shown in Figures 3 and 4. When used with a 5V regulator, a 16V 10F Y5V capacitor can exhibit an effective value as low as 1F to 2F for the DC bias voltage applied and over the operating temperature range. The X5R and X7R dielectrics yield more stable characteristics and are more suitable for use as the output capacitor. The X7R type has better stability across temperature, while the X5R is less expensive and is available in higher values. One must still exercise care when using X5R and X7R capacitors; the X5R and X7R codes only specify operating temperature range and maximum capacitance change over temperature. Capacitance change due to DC bias with X5R and X7R capacitors is better than Y5V and Z5U capacitors, but can still be significant enough to drop capacitor values below appropriate levels. Capacitor DC bias characteristics tend to improve as component case size increases, but expected capacitance at operating voltage should be verified. Voltage and temperature coefficients are not the only sources of problems. Some ceramic capacitors have a 40 20 BOTH CAPACITORS ARE 16V, 1210 CASE SIZE, 10F 20 X5R CHANGE IN VALUE (%) CHANGE IN VALUE (%) 0 -20 -40 -60 Y5V -80 -100 -20 -40 2 4 8 6 10 12 DC BIAS VOLTAGE (V) 14 16 3008 F03 Figure 3. Ceramic Capacitor DC Bias Characteristics Y5V -60 -80 0 X5R 0 BOTH CAPACITORS ARE 16V, 1210 CASE SIZE, 10F -100 -50 -25 50 25 75 0 TEMPERATURE (C) 100 125 3008 F04 Figure 4. Ceramic Capacitor Temperature Characteristics 3008fc 13 LT3008 Series APPLICATIONS INFORMATION piezoelectric response. A piezoelectric device generates voltage across its terminals due to mechanical stress, similar to the way a piezoelectric accelerometer or microphone works. For a ceramic capacitor, the stress can be induced by vibrations in the system or thermal transients. The resulting voltages produced can cause appreciable amounts of noise, especially when a ceramic capacitor is used for noise bypassing. A ceramic capacitor produced Figure 5's trace in response to light tapping from a pencil. Similar vibration induced behavior can masquerade as increased output voltage noise. VOUT = 0.6V COUT = 22F ILOAD = 10A VOUT 500V/DIV GND pin current is found by examining the GND Pin Current curves in the Typical Performance Characteristics section. Power dissipation is equal to the sum of the two components listed prior. The LT3008 regulator has internal thermal limiting designed to protect the device during overload conditions. For continuous normal conditions, do not exceed the maximum junction temperature rating of 125C. Carefully consider all sources of thermal resistance from junction to ambient including other heat sources mounted in proximity to the LT3008. For surface mount devices, heat sinking is accomplished by using the heat spreading capabilities of the PC board and its copper traces. Copper board stiffeners and plated through-holes can also be used to spread the heat generated by power devices. The following tables list thermal resistance for several different board sizes and copper areas. All measurements were taken in still air on 3/32" FR-4 two-layer boards with one ounce copper. 100ms/DIV 3008 F05 Figure 5. Noise Resulting from Tapping on a Ceramic Capacitor Thermal Considerations The LT3008's maximum rated junction temperature of 125C limits its power-handling capability. Two components comprise the power dissipated by the device: PCB layers, copper weight, board layout and thermal vias affect the resultant thermal resistance. Although Tables 2 and 3 provide thermal resistance numbers for 2-layer boards with 1 ounce copper, modern multilayer PCBs provide better performance than found in these tables. Table 2: Measured Thermal Resistance for DC Package COPPER AREA TOPSIDE* BACKSIDE BOARD AREA THERMAL RESISTANCE (JUNCTION-TO-AMBIENT) 1. Output current multiplied by the input/output voltage differential: IOUT * (VIN - VOUT) 2500mm2 2500mm2 2500mm2 65C/W 1000mm2 2500mm2 2500mm2 70C/W 2. GND pin current multiplied by the input voltage: IGND * VIN 225mm2 2500mm2 2500mm2 75C/W 100mm2 2500mm2 2500mm2 80C/W 50mm2 2500mm2 2500mm2 85C/W *Device is mounted on the topside. 3008fc 14 LT3008 Series APPLICATIONS INFORMATION Table 3: Measured Thermal Resistance for TSOT-23 Package COPPER AREA TOPSIDE* BACKSIDE BOARD AREA THERMAL RESISTANCE (JUNCTION-TO-AMBIENT) 2500mm2 2500mm2 2500mm2 65C/W 1000mm2 2500mm2 2500mm2 67C/W 225mm2 2500mm2 2500mm2 70C/W 100mm2 2500mm2 2500mm2 75C/W 50mm2 2500mm2 2500mm2 85C/W *Device is mounted on the topside. For example, a 4-layer, 1 ounce copper PCB board with 3 thermal vias from the DFN exposed backside or the 3 fused TSOT-23 GND pins to inner layer GND planes achieves 45C/W thermal resistance. Demo circuit DC 1388A's board layout achieves this 45C/W performance. This is approximately a 30% improvement over the lowest numbers shown in Tables 2 and 3. Calculating Junction Temperature Example: Given an output voltage of 3.3V, an input voltage range of 12V 5%, an output current range of 0mA to 20mA and a maximum ambient temperature of 85C, what will the maximum junction temperature be for an application using the DC package? The power dissipated by the device is equal to: IOUT(MAX) (VIN(MAX) - VOUT) + IGND (VIN(MAX)) where, IOUT(MAX) = 20mA VIN(MAX) = 12.6V IGND at (IOUT = 20mA, VIN = 12.6V) = 0.3mA So, P = 20mA(12.6V - 3.3V) + 0.3mA(12.6V) = 189.8mW The thermal resistance ranges from 65C/W to 85C/W depending on the copper area. So, the junction temperature rise above ambient approximately equals: 0.1898W(75C/W) = 14.2C The maximum junction temperature equals the maximum junction temperature rise above ambient plus the maximum ambient temperature or: TJ(MAX) = 85C + 14.2C = 99.2C Protection Features The LT3008 incorporates several protection features that make it ideal for use in battery-powered circuits. In addition to the normal protection features associated with monolithic regulators, such as current limiting and thermal limiting, the device also protects against reverse-input voltages, reverse-output voltages and reverse output-toinput voltages. Current limit protection and thermal overload protection protect the device against current overload conditions at the output of the device. For normal operation, do not exceed a junction temperature of 125C. The typical thermal shutdown circuitry temperature threshold is 160C. The IN pin withstands reverse voltages of 50V. The device limits current flow to less than 30A (typically less than 1A) and no negative voltage appears at OUT. The device protects both itself and the load against batteries that are plugged in backwards. 3008fc 15 LT3008 Series APPLICATIONS INFORMATION The LT3008 incurs no damage if OUT is pulled below ground. If IN is left open circuit or grounded, OUT can be pulled below ground by 50V. No current flows from the pass transistor connected to OUT. However, current flows in (but is limited by) the resistor divider that sets output voltage. Current flows from the bottom resistor in the divider and from the ADJ pin's internal clamp through the top resistor in the divider to the external circuitry pulling OUT below ground. If IN is powered by a voltage source, OUT sources current equal to its current limit capability and the LT3008 protects itself by thermal limiting if necessary. In this case, grounding the SHDN pin turns off the LT3008 and stops OUT from sourcing current. The LT3008 incurs no damage if the ADJ pin is pulled above or below ground by 50V. If IN is left open circuit or grounded, ADJ acts like a 100k resistor in series with a diode when pulled above or below ground. In circuits where a backup battery is required, several different input/output conditions can occur. The output voltage may be held up while the input is either pulled to ground, pulled to some intermediate voltage or is left open circuit. Current flow back into the output follows the curve shown in Figure 6. If the LT3008 IN pin is forced below the OUT pin or the OUT pin is pulled above the IN pin, input current typically drops to less than 1A. This occurs if the LT3008 input is connected to a discharged (low voltage) battery and either a backup battery or a second regulator circuit holds up the output. The state of the SHDN pin has no effect in the reverse current if OUT is pulled above IN. 100 90 REVERSE CURRENT (A) The SHDN pin cannot be driven below GND unless tied to the IN pin. If the SHDN pin is driven below GND while IN is powered, the output will turn on. SHDN pin logic cannot be referenced to a negative rail. 80 70 ADJ CURRENT 60 50 40 30 20 OUT CURRENT 10 0 0 1 2 3 4 5 6 7 8 9 OUTPUT AND ADJ VOLTAGE (V) 10 3008 F06 Figure 6. Reverse-Output Current 3008fc 16 LT3008 Series TYPICAL APPLICATIONS Keep-Alive Power Supply NO PROTECTION DIODES NEEDED! VIN 12V IN 1F 3.3V OUT 2.2F LT3008-3.3 SHDN LOAD: SYSTEM MONITOR, VOLATILE MEMORY, ETC. SENSE GND 3009 TA02 Last-Gasp Circuit LINE POWER VLINE 12V TO 15V SENSE DCHARGE LINE INTERRUPT DETECT RLIMIT IN SUPERCAP 1F OUT LT3008-5 5V TO MONITORING CENTER FAULT PWR GND 2.2F 3008 TA03 SHDN SENSE GND PACKAGE DESCRIPTION DC6 Package 6-Lead Plastic DFN (2mm x 2mm) (Reference LTC DWG # 05-08-1703 Rev B) R = 0.125 TYP 0.56 0.05 (2 SIDES) 0.70 0.05 2.55 0.05 1.15 0.05 0.61 0.05 (2 SIDES) PIN 1 BAR PACKAGE TOP MARK OUTLINE (SEE NOTE 6) 0.25 0.05 0.50 BSC 1.42 0.05 (2 SIDES) 0.200 REF RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS NOTE: 1. DRAWING TO BE MADE A JEDEC PACKAGE OUTLINE M0-229 VARIATION OF (WCCD-2) 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 0.40 0.10 4 6 2.00 0.10 (4 SIDES) PIN 1 NOTCH R = 0.20 OR 0.25 x 45 CHAMFER R = 0.05 TYP 0.75 0.05 (DC6) DFN REV B 1309 3 1 0.25 0.05 0.50 BSC 1.37 0.05 (2 SIDES) 0.00 - 0.05 BOTTOM VIEW--EXPOSED PAD 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 3008fc 17 LT3008 Series PACKAGE DESCRIPTION TS8 Package 8-Lead Plastic TSOT-23 (Reference LTC DWG # 05-08-1637 Rev A) 0.40 MAX 2.90 BSC (NOTE 4) 0.65 REF 1.22 REF 1.4 MIN 3.85 MAX 2.62 REF 2.80 BSC 1.50 - 1.75 (NOTE 4) PIN ONE ID RECOMMENDED SOLDER PAD LAYOUT PER IPC CALCULATOR 0.22 - 0.36 8 PLCS (NOTE 3) 0.65 BSC 0.80 - 0.90 0.20 BSC 0.01 - 0.10 1.00 MAX DATUM `A' 0.30 - 0.50 REF 0.09 - 0.20 (NOTE 3) 1.95 BSC TS8 TSOT-23 0710 REV A NOTE: 1. DIMENSIONS ARE IN MILLIMETERS 2. DRAWING NOT TO SCALE 3. DIMENSIONS ARE INCLUSIVE OF PLATING 4. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR 5. MOLD FLASH SHALL NOT EXCEED 0.254mm 6. JEDEC PACKAGE REFERENCE IS MO-193 3008fc 18 LT3008 Series REVISION HISTORY (Revision history begins at Rev B) REV DATE DESCRIPTION PAGE NUMBER B 02/10 Added MP grade in TS8 package Revised curve G04 in Typical Performance Characteristics 7 C 04/12 Clarified E-Grade Operating Temperature 6 Updated Package Drawings 2-4, 6 17, 18 3008fc Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 19 LT3008 Series TYPICAL APPLICATION Low Duty Cycle Applications IN 1F OUT 100 3.3V 90 2.2F LT3008-3.3 SHDN LOW DUTY CYCLE PULSED LOAD 0mA TO 10mA SENSE GND 3008 TA04a 80 POWER SAVINGS (%) VIN 12V Average Power Savings for Low Duty Cycle Applications 0mA to 10mA Pulsed Load, IN = 12V 70 60 100A IQ 50 40 30A IQ 30 20 10 0 0.1 10A IQ 1 10 DUTY CYCLE (%) 3008 TA04b RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT1761 100mA, Low Noise Micropower LDO VIN : 1.8V to 20V, VOUT = 1.22V, VDO = 0.3V, IQ = 20A, ISD < 1A, Low Noise: < 20VRMS , Stable with 1F Ceramic Capacitors, ThinSOTTM Package LT1762 150mA, Low Noise Micropower LDO VIN : 1.8V to 20V, VOUT = 1.22V, VDO = 0.3V, IQ = 25A, ISD < 1A, Low Noise: < 20VRMS , MS8 Package LT1763 500mA, Low Noise Micropower LDO VIN : 1.8V to 20V, VOUT = 1.22V, VDO = 0.3V, IQ = 30A, ISD < 1A, Low Noise: < 20VRMS , S8 Package LT1764/LT1764A 3A, Low Noise, Fast Transient Response LDOs VIN : 2.7V to 20V, VOUT = 1.21V, VDO = 0.34V, IQ = 1mA, ISD < 1A, Low Noise: < 40VRMS , LT1764A Version Stable with Ceramic Capacitors, DD and TO220-5 Packages LT1962 300mA, Low Noise Micropower LDO VIN : 1.8V to 20V, VOUT(MIN) = 1.22V, VDO = 0.27V, IQ = 30A, ISD < 1A, Low Noise: < 20VRMS , MS8 Package LT1963/LT1963A 1.5A, Low Noise, Fast Transient Response LDOs VIN : 2.1V to 20V, VOUT(MIN) = 1.21V, VDO = 0.34V, IQ = 1mA, ISD < 1A, Low Noise: < 40VRMS , LT1963A Version Stable with Ceramic Capacitors, DD, TO220-5, SOT223 and S8 Packages LT3009 20mA, 3A IQ Micropower LDO VIN : 1.6V to 20V, Low IQ: 3A, VDO = 0.28V, 2mm x 2mm DFN and SC70-8 Packages LT3020 100mA, Low Voltage VLDO VIN : 0.9V to 10V, VOUT(MIN) = 0.20V, VDO = 0.15V, IQ = 120A, ISD < 1A, 3mm x 3mm DFN and MS8 Packages LT3021 500mA, Low Voltage VLDO VIN : 0.9V to 10V, VOUT(MIN) = 0.20V, VDO = 0.16V, IQ = 120A, ISD < 3A, 5mm x 5mm DFN and SO8 Packages LT3080/ LT3080-1 1.1A, Parallelable, Low Noise, Low Dropout Linear Regulator 300mV Dropout Voltage (2-Supply Operation), Low Noise: 40VRMS, VIN: 1.2V to 36V, VOUT: 0V to 35.7V, Current-Based Reference with 1-Resistor VOUT Set; Directly Parallelable (No Op Amp Required), Stable with Ceramic Caps, TO-220, SOT-223, MSOP and 3mm x 3mm DFN Packages; LT3080-1 Version Has Integrated Internal Ballast Resistor LT3085 275mV Dropout Voltage (2-Supply Operation), Low Noise: 40VRMS , VIN: 1.2V to 36V, VOUT: 0V to 35.7V, Current-Based Reference with 1-Resistor VOUT Set; Directly Parallelable (No Op Amp Required), Stable with Ceramic Caps, MSOP-8 and 2mm x 3mm DFN Packages 500mA, Parallelable, Low Noise, Low Dropout Linear Regulator ThinSOT is a trademark of Linear Technology Corporation. 3008fc 20 Linear Technology Corporation LT 0412 REV C * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 www.linear.com (c) LINEAR TECHNOLOGY CORPORATION 2007