CLASSIFICATION SUBJECT PRODUCT SPECIFICATION No. DS-9320-2400-102 WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF DATE REV. 0.1 1 of 35 22.04.2015 Product Specification Applicant / Manufacturer Hardware Panasonic Industrial Devices Europe GmbH Zeppelinstrasse 19 21337 Luneburg Germany Applicant / Manufacturer Software Software Version Refer to chapter 22 / 26.5 for information regarding software versions Refer to chapter 22 / 26.5 for information regarding software versions By purchase of any of products described in this document the customer accepts the document's validity and declares their agreement and understanding of its contents and recommendations. Panasonic reserves the right to make changes as required without notification. Power Electronics R&D Center Wireless Connectivity Panasonic Industrial Devices Europe GmbH APPROVED genehmigt CHECKED gepruft DESIGNED erstellt CLASSIFICATION SUBJECT PRODUCT SPECIFICATION No. DS-9320-2400-102 WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF DATE REV. 0.1 2 of 35 22.04.2015 TABLE OF CONTENTS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. Scope of this Document ................................................................................................ 4 History for this Document .............................................................................................. 4 Data Sheet Status ......................................................................................................... 4 Related Documents ....................................................................................................... 4 Key Features ................................................................................................................. 5 Applications for the Module ........................................................................................... 5 Wireless Local Area Network ........................................................................................ 5 Description for the Module............................................................................................. 6 Detailed Description ...................................................................................................... 7 9.1. PAN9320 Terminal Layout ................................................................................... 7 9.2. Common Terminal Pin-Configuration ................................................................... 7 General Features .......................................................................................................... 9 HOST Interfaces ........................................................................................................... 9 11.1. UART0 Interface (Command) ............................................................................... 9 11.2. UART1 Interface (data) ........................................................................................ 9 Peripheral Bus Interface ................................................................................................ 9 WLAN Features........................................................................................................... 10 13.1. IEEE 802.11 / Standards .................................................................................... 10 13.2. WLAN MAC ........................................................................................................ 10 13.3. WLAN Baseband................................................................................................ 10 13.4. WLAN Radio ...................................................................................................... 11 13.5. WLAN Encryption ............................................................................................... 11 PAN9320 Block Diagram ............................................................................................. 12 Key Parts List .............................................................................................................. 12 Test Conditions ........................................................................................................... 12 General Requirements and Operation ......................................................................... 13 17.1. Absolute Maximum Ratings ................................................................................ 13 17.2. Recommended Operating Conditions................................................................. 13 17.3. Digital Pin Characteristics .................................................................................. 13 17.4. Electrical characeristics ...................................................................................... 14 17.4.1. Current consumption ............................................................................. 14 17.5. Internal Operating Frequencies .......................................................................... 14 17.6. Coexistence Interface Specification.................................................................... 15 17.6.1. Marvell(R) 3/4-Wire Timing Data .............................................................. 15 17.6.2. WL_ACTIVE 2/3/4-Wire Timing Data .................................................... 16 17.7. Host Interface Specification ................................................................................ 17 17.7.1. UART0 Interface (Command) ................................................................ 17 17.7.2. UART1 Interface (Data) ........................................................................ 17 RF Electrical Characteristics ....................................................................................... 18 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. No. DS-9320-2400-102 DATE REV. 0.1 3 of 35 22.04.2015 18.1. WLAN Radio Specification ................................................................................. 18 18.2. WLAN RF Characteristics .................................................................................. 19 18.2.1. RF Characteristics for IEEE 802.11b ..................................................... 19 18.2.2. RF Characteristics for IEEE 802.11g ..................................................... 20 18.2.3. RF Characteristics for IEEE 802.11n (BW 20 MHz) ............................... 21 18.2.4. RF Characteristics for IEEE 802.11n (BW 40 MHz)............................... 22 Soldering Temperature-Time Profile (for reflow soldering)........................................... 23 19.1. For lead solder ................................................................................................... 23 19.2. For leadfree solder ............................................................................................. 23 PAN9320 Module Dimension ...................................................................................... 24 PAN9320 FootPrint of the Module ............................................................................... 25 Case Marking (Example for PAN9320) ........................................................................ 26 Mechanical Requirements ........................................................................................... 27 Reliability Tests ........................................................................................................... 27 Cautions ...................................................................................................................... 27 25.1. Design Notes ..................................................................................................... 27 25.2. Installation Notes................................................................................................ 28 25.3. Usage Conditions Notes..................................................................................... 28 25.4. Storage Notes .................................................................................................... 28 25.5. Safety Cautions .................................................................................................. 29 25.6. Other cautions .................................................................................................... 29 Packaging ................................................................................................................... 30 26.1. PAN9320 Tape Dimension ................................................................................. 30 26.2. Packing in Tape ................................................................................................. 30 26.3. Component Direction ......................................................................................... 31 26.4. Reel Dimension .................................................................................................. 31 26.5. Label for Package .............................................................................................. 32 26.6. Total Package .................................................................................................... 32 Ordering Information ................................................................................................... 33 RoHS Declaration ....................................................................................................... 33 Regulatory Information ................................................................................................ 34 29.1. FCC for US ........................................................................................................ 34 29.2. Industry Canada Certification ............................................................................. 34 29.3. European R&TTE Declaration of Conformity ...................................................... 34 General Information..................................................................................................... 35 Life Support Policy ...................................................................................................... 35 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF 1. No. DS-9320-2400-102 DATE REV. 0.1 4 of 35 22.04.2015 SCOPE OF THIS DOCUMENT This product specification applies to Panasonic's Wi-Fi IEEE 802.11 b/g/n full embedded module with series name PAN9320. 2. 3. HISTORY FOR THIS DOCUMENT Revision Date Modification / Remarks 0.1 22.04.2015 1st preliminary version DATA SHEET STATUS This data sheet contains the PRELIMINARY specification. Supplementary data will be published at a later date. Panasonic reserves the right to make changes at any time without notice. Consult the most recently issued data sheet before initiating or completing a design. 4. RELATED DOCUMENTS Search these homepages for documentation updates. [1] PAN9320 Software-Guide http://pideu.panasonic.de/produkte/Funkmodule.html [2] Semiconductor Datasheet (R) 88MC200 from Marvell (R) 88W8782 from Marvell [3] Application Note Land Grid Array http://www.pideu.panasonic.de/pdf/184ext.pdf [4] REACH and RoHS Certificate http://pideu.panasonic.de/files/Documents/WM_Documents/PAN9320/WMREACH_and_RoHS_directive.pdf PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF 5. DATE REV. 0.1 5 of 35 22.04.2015 KEY FEATURES 6. No. DS-9320-2400-102 Surface Mount Type 29.0 x 13.5 x 2.6 mm Wireless Local Area Network (WLAN) module with integrated MCU and Radio (SoC) Operating in the 2.4GHz ISM band Supports IEEE 802.11 IEEE 802.11b/g payload data rates IEEE 802.11n high throughput data rates IEEE 802.11i security standards WEP, TKIP, AES-CCMP and AES-CMAC IEEE 802.11e Quality of Service (QoS) Coexistence Interface for external co-located 2.4GHz radios (e.g. Bluetooth) Tx power up to +18 dBm (IEEE 802.11b) High Rx sensitivity -98dBm (IEEE 802.11b DSSS 1Mbps) -76dBm (IEEE 802.11g OFDM 54Mbps) -74dBm (IEEE 802.11n MCS7 HT20 65Mbps) -71dBm (IEEE 802.11n MCS7 HT40 135Mbps) Marvell(R) 88W8782 WLAN System-on-Chip (SoC) and 88MC200 (MCU) inside Integrated flash for customer web contents and configuration file 1,5MB yte (extentable) High performance low power CPU core Internal crystal oscillators for Radio (40MHz) and MCU (32MHz) 2 UART interfaces (Command, Data) Integrated shielding to resist EMI Manufactured in conformance with RoHS APPLICATIONS FOR THE MODULE All Embedded Wireless Applications 7. White goods Home Automation Internet of Things Fitness Equipment Lighting Control M2M Communication Printer Smart Meters Media Player Sensors POS Terminal Patient Monitors WIRELESS LOCAL AREA NETWORK Wireless Local Area Network (WLAN) is a local radio network defined in part by the IEEE 802.11 family of standards. The IEEE 802.11 is an international standard describing the wireless network. The standard defines the lower layers of the OSI model for wireless communication with the Physical Layer (PHY) and the Data Link Layer (DLL) with its two sub-layers Logical Link Control (LLC) and Media Access Control (MAC), making it possible to use any protocol over a IEEE 802.11 wireless network as an Ethernet network. Basically WLAN networks use two operating modes for connecting station computers (STA) equipped with a wireless network adapter. The first one is the infrastructure mode where the wireless clients are connected via one or more access points (AP) to a wired network. In this case the network is configured with the same Service Set Identifier (SSID) network name in order to communicate. The second one is the ad-hoc mode where wireless clients are connected without any access point to the internet. WLAN devices typically have a higher transmit power to cover a radio range about 100m. Furthermore WLAN is commonly used to transmit high throughput data using Orthogonal Frequency Division Multiplexing PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION No. DS-9320-2400-102 WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF DATE REV. 0.1 6 of 35 22.04.2015 (OFDM) modulation. The Carrier Sense Multiple Access with Collosion Avoidance (CSMA/CA) mechanism enables the parallel access of more than one device to the media of a IEEE 802.11 network. By implementation of security mechanisms like Adavanced Encryption Standard (AES) with Counter Mode CBCMAC Protocol (CCMP) or Cipher-Based Message Authentication Code (CMAC) and Wired Equivalent Privacy (WEP) with Temporal Key Integrity Protocol (TKIP) the network is supporting the security standard IEEE 802.11i. Video, voice and multimedia applications are supported by the IEEE 802.11e Quality of Service amendment. 8. DESCRIPTION FOR THE MODULE The PAN9320 series is a 2.4GHz ISM band wireless radio module for implementing WLAN functionality into various electronic devices. A block diagram can be found in chapter 14. The PAN9320 series is a cost-effective, low-power consumption, system-on-chip (SoC) solution for WLAN applications. It enables wireless network adapters and cards to be built with low total bill-of-material costs. The PAN9320 series combines an excellent 802.11 wireless radio, baseband processor, medium access controller, encryption unit, CPU, boot ROM with patching capability, internal SRAM, in-system programmable flash memory and many other powerful supporting features and peripherals. The PAN9320 is suitable for wireless network systems based on WLAN IEEE 802.11 b/g/n 2.4GHz where small form factor, highly integration, high throughput data rates and low RF expertise are required. The PAN9320 includes integrated firmware consisting of TCP/IP-stack on 802.11 MAC with various application features. The Driver-Firmware Interface handles all 802.11 MAC management tasks by converting standard 802.3 Ethernet frames to the SoC firmware to transmit over the wireless link as 802.11 frames and processes the received 802.11 frames and converts them into 802.3 Ethernet frames before forwarding them to the host driver. The HOST driver is seperated in three modules. The Standard Ethernet driver, the 802.11 Extensions and the Hardware Interface Driver. The 802.11 Extensions module extends the Standard Ethernet driver in order to view and control the state of the WLAN adapter. The Hardware Interface Driver controls the (R) hardware interface on the HOST side. Additonally the software package from Marvell consists of various applications, demonstrations and utilities. Refer to [1] PAN9320 Software-Guide and chapter 27 Ordering Information. Please contact your local sales office for further details on additional options and services: www.panasonic.com/rfmodules for the US, http://industrial.panasonic.com/eu/i/29606/wireless_modules/wireless_modules.html for EU or write an e-mail to wireless@eu.panasonic.com. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF 9. No. DS-9320-2400-102 PRODUCT SPECIFICATION REV. 0.1 7 of 35 DATE 22.04.2015 DETAILED DESCRIPTION 9.1. PAN9320 TERMINAL LAYOUT Top View, Application PCB Top View 35 34 32 31 30 29 37 F1 F2 F3 F4 F5 38 E1 E2 E3 E4 E5 28 27 26 25 D1 D2 D3 D4 D5 40 C1 C2 C3 C4 C5 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 1 GND THERMO 19 18 GND THERMO 41 B1 B2 B3 B4 B5 17 42 A1 A2 A3 A4 A5 16 4 5 6 7 8 1 No 22 20 GND THERMO 9.2. 23 21 GND THERMO 39 24 2 3 Chip Antenna 33 36 9 10 11 12 13 14 15 COMMON TERMINAL PIN-CONFIGURATION Pin Name GND GPIO441 GPIO451 USB AVDD 33 USB DP USB DM 3.3V 3.3V UART1 CTS UART1 RTS UART1 TXD UART1 RXD QSPI CS2 GND GND NC GND GND GND GND GND GND Pin Type Ground Pin Digital I/O Digital I/O Power Analog I/O Analog I/O Power Power Digital In Digital Out Digital Out Digital In Digital Out Ground Pin Ground Pin NC Ground Pin Ground Pin Ground Pin Ground Pin Ground Pin Ground Pin Description Connect to Ground Digital I/O #44 Digital I/O #45 Don't connect, only for internal purpose Don't connect, only for internal purpose Don't connect, only for internal purpose 3.0V - 3.6V power supply connection 3.0V - 3.6V power supply connection CTSn for UART1 RTSn for UART 1 TXD for UART1 RXD for UART1 Chip Select for external QSPI Flash Memory (option) Connect to Ground Connect to Ground NC Connect to Ground Connect to Ground Connect to Ground Connect to Ground Connect to Ground Connect to Ground All GPIO's are initial set to output with low level PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF No 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 A1 A2 A3 A4 A5 B1 B2 B3 B4 B5 C1 C2 C3 C4 C5 D1 D2 D3 D4 D5 E1 E2 E3 E4 E5 F1 F2 F3 F4 F5 2 No. DS-9320-2400-102 Pin Name GND GND GND W STAT LED UART0 TXD UART0 RXD GPIO41 1 GPIO5 1 GPIO6 1 GPIO7 STAT LED1 STAT LED2 STAT LED3 GND RESETn WAKE UP0 BOOT GPIO281 MCU READY FACTORY RESET SD DAT3 SD DAT2 SD DAT1 SD DAT0 SD CMD SD CLK BT FREQ BT GRANTN BT REQ BT STATE NC NC WAKE UP1 QSPI CLK QSPI D3 TDI TRSTn NC QSPI D0 QSPI D1 TDO TCK TMS QSPI D2 QSPI CS W PDn W RESETn GND GND GND Pin Type Ground Pin Ground Pin Ground Pin Digital Out Digital Out Digital In Digital I/O Digital I/O Digital I/O Digital I/O Digital Out Digital Out Digital Out Ground Pin Digital In Digital In Digital In Digital I/O Digital Out Digital In Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital Out Input Signal Output Signal Input Signal Input Signal Digital In Digital Out Digital I/O Digital In Digital In Digital I/O Digital I/O Digital Out Digital Out Digital I/O Digital I/O Digital Out Digital In Input Signal Ground Pin Ground Pin Ground Pin DATE REV. 0.1 8 of 35 22.04.2015 Description Connect to Ground Connect to Ground Connect to Ground Connect to WiFi-Status LED TXD for UART0 RXD for UART0 Digital I/O #4 Digital I/O #5 Digital I/O #6 Digital I/O #7 Connect to Microcontroller-Status LED, active low Connect to IP-Connectivity LED active low Connect to Error LED active low Connect to Ground Resetn, active low Wake up signal for MCU, active high Boot option, High level: boot from internal flash, Low level: boot over UART 2 Digital I/O #28 Connect to Ready-LED, active high Factory reset, active high Don't connect, only for internal purpose Don't connect, only for internal purpose Don't connect, only for internal purpose Don't connect, only for internal purpose Don't connect, only for internal purpose Don't connect, only for internal purpose Information BT using channel which overlaps WLAN channel or not Indicate permission to transmit, low BT can transmit BT device request access to medium Information BT_REQ priority (1- or 2-bit) and direction BT RX/TX Don't connect, only for internal purpose Don't connect, only for internal purpose Don't connect, only for internal purpose Clock for QSPI Data3 for QSPI TDI for JTAG TRSTn for JTAG Don't connect, only for internal purpose Data0 for QSPI Data1 for QSPI TDO for JTAG TCK for JTAG TMS for JTAG Data2 for QSPI Chip select for internal QSPI Flash Memory Don't connect, only for internal purpose Don't connect, only for internal purpose Connect to Ground Connect to Ground Connect to Ground Connect the Boot-Pin over a 100 Ohm resistor to Vcc or GND PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION No. DS-9320-2400-102 WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF DATE REV. 0.1 9 of 35 22.04.2015 10. GENERAL FEATURES Surface Mount Type 29,0 x 13.5 x 2.66 mm Wireless Local Area Network (WLAN) module with integrated MCU and Radio (SoC) Integrated embedded stack, interfaces Telnet, http, Ajax, Jason, others Wireless Update of Radio Driver and MCU Firmware with integrated bootloader Integrated flash for customer web contents up to 1.5MByte Evaluation and Development software for Windows Getting started Tutorials, Libraries, APIs Easy to use Evaluation Board for quick development and reduced time to market Supports IEEE 802.11 b/g/n and security standards WEP, WPA, WPA2 Tx power up to +18 dBm (IEEE 802.11b) High Rx sensitivity -98 dBm (IEEE 802.11b DSSS 1Mbps) Marvell(R) 88W8782 WLAN System-on-Chip (SoC) and 88MC200 (MCU) inside High performance low power CPU core Two Internal crystal oscillator 32MHz and 40MHz Programming over JTAG HOST communication interfaces UART0 (Command) and UART1 (Data tunnel) Integrated shielding to resist EMI 11. HOST INTERFACES 11.1. UART0 INTERFACE (COMMAND) 2-wire data transfer (RX, TX) Programmable baud rate (110bps to 1.5 Mbps) Data format (LSB first) Data bit: (5-8 bit) Parity bit: (0-4 bit) Stop bit: (1-2 bit) 11.2. UART1 INTERFACE (DATA) 4-wire data transfer (RX, TX, RTS, CTS) Programmable baud rate (110bps to 1.5 Mbps) Data format (LSB first) Data bit: (5-8 bit) Parity bit: (0-4 bit) Stop bit: (1-2 bit) 12. PERIPHERAL BUS INTERFACE Embedded WLAN SoC with following features: Clocked Serial Unit (CSU) 3-Wire, 4-Wire (3W4W) Interface 2-Wire Serial Interface (TWSI) 1-Wire Serial Interface General-Purpose I/O (GPIO) Interface User-defined GPIOs, I/O configured to either input or output GPIOs independently controlled GPIO1 with LED output functionality LED Pulse Stretching to observe short duration of status events Two software controlled blink rates to indicate events PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION No. DS-9320-2400-102 WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF DATE REV. 0.1 10 of 35 22.04.2015 13. WLAN FEATURES 13.1. IEEE 802.11 / STANDARDS 802.11 data rates 1 and 2 Mbps (DSSS) 802.11b data rates 5.5 and 11 Mbps (CCK) 802.11g data rates 6, 9, 12, 18, 24, 36, 48 and 54 Mbps (OFDM) 802.11b/g performance enhancements 802.11n compliant with maximum data rates up to 72 Mbps (20 MHz channel) and 150 Mbps (40 MHz channel) 802.11d international roaming 802.11i enhanced security (WEP, WPA, WPA2) 3 802.11k radio resource measurement 3 802.11r fast hand-off for AP roaming 3 802.11w protected management frames Support clients (stations) implementing IEEE Power Save mode 13.2. WLAN MAC 3 Ad-Hoc and Infrastructure Modes RTS/CTS for operation und DCF Hardware filtering of 32 multicast addresses and duplicate frame detection for up to 32 unicast addresses WLAN SoC with Tx and Rx FIFO for maximum throughput Open System and Shared Key Authentication services A-MPDU Rx (de-aggregation) and Tx (aggregation) 20/40 MHz channel coexistence Reduced Inter-Frame Spacing (RIFS) bursting Management Information Base (MIB) counter Radio resource measurement counters Block acknowledgement with 802.11n extensions Transmit beamformer support Transmit rate adaptation Transmit power control Long and short preamble generation on a frame-by-frame basis for 802.11b frames (R) Marvell Mobile Hotspot technology (MMH) 13.3. WLAN BASEBAND 3 802.11n 1x1 SISO (WLAN SoC with SISO RF radio) Backward compatibility with legacy 802.11b/g technology PHY data rates up to 150 Mbps (802.11n - MCS7) 20 MHz bandwidth/channel, 40 MHz bandwidth/channel, upper/lower 20 MHz bandwidth in 40 MHz channel and 20 MHz duplicate legacy bandwidth in 40 MHz channel mode operation Modulation and Coding Scheme MCS 0 ~ 7 and MCS 32 (duplicate 6 Mbps) Radio resource measurement Optional 802.11n SISO features: 20/40 MHz coexistence 1-stream Space-Time-Block-Coding (STBC) reception Short Guard Interval RIFS on receive path Beamformer function and hardware acceleration Greenfield Tx/Rx Hardware supported, not implemented in the software stack PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION No. DS-9320-2400-102 WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF DATE REV. 0.1 11 of 35 22.04.2015 13.4. WLAN RADIO 20 and 40 MHz channel bandwidth Embedded WLAN SoC with following features: Direct conversion radio (no SAW filter) 2.4GHz Tx/Rx switch, Power Amplifier (PA) and Low Noise Amplifier (LNA) path Gain selectable LNAs with optimized noise figure and power consumption Power Amplifiers with power control Closed loop power control (0.5 dB step increments) Optimized Tx gain distribution for linearity and noise performance Fine channel step with AFC (adaptive frequency control) 13.5. WLAN ENCRYPTION Embedded WLAN SoC with following features: WEP 64-bit and 128-bit encryption with hardware TKIP processing (WPA) AES-CCMP hardware implementation as part of 802.11i security standard (WPA2) Enhanced AES engine performance AES-Cipher-Based Message Authentication Code (CMAC) as part of the 802.11w security 3 standard PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT No. DS-9320-2400-102 PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF REV. 0.1 12 of 35 DATE 22.04.2015 14. PAN9320 BLOCK DIAGRAM Wi-Fi 2.4G b/g/n - Full Embedded - Module PAN 9320 DC/DC Step-down Converter Vcc 3.3V 3.3V JTAG UART0 (Command) UART1 (Data) Q-SPI (ext. FLASH) Status LED`s GPIO`s USB (CDC Device) MCU READY Factory Reset Microcontroller Unit AHB Bus DMA Debug AON Unit JTAG OSC Flash Cntl SWD Connectivity I2C UART Q-SPI GPIO I/O Multiplexer RESETn / PDn WAKE UP0/1 MPU USB SDIO PMIP Memory System Unit ROM Timer SRAM WDT FLASH I2S RTC PMU ADC/DAC Analog Unit T-Sensor OSC/PLL ACOMP 3.3V WLAN-SoC Power Management CPU JTAG 32 MHz SDIO (Testing) Q-SPI Flash B U S GPIO CPU I/F 802.11 MAC Baseband ROM SRAM Peripheral Bus Unit OTP SDIO LDO I/F Encryption UART LED Stretch Crystal C P U SDIO Controller Ceramic Chip Antenna Sleep C O N T R O L B U S 2.4G 1.8V WLAN RF Direct Conversion SPDT OSC PLL 2.4G TX/RX LPF Crystal 40 MHz 15. KEY PARTS LIST Part Name Material P.W.Board Glass cloth epoxide resin with gold plating Casing Material: C7521, thickness 0.30mm IC (WLAN-SoC) 88W8782 (Marvell(R), www.marvell.com) IC (Microcontroller Unit) 88MC200 (Marvell(R), www.marvell.com) 16. TEST CONDITIONS Measurements shall be made under operating free-air temperature range unless otherwise specified. Temperature Humidity Supply Voltage 25 10C 40 to 85%RH 3.3V PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION No. DS-9320-2400-102 WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF REV. 0.1 13 of 35 DATE 22.04.2015 17. GENERAL REQUIREMENTS AND OPERATION All specifications are over temperature and process, unless indicated otherwise. 17.1. ABSOLUTE MAXIMUM RATINGS The maximum ratings may not be exceeded under any circumstances, not even momentarily and individually, as permanent damage to the module will result. Symbol Parameter TSTOR Storage temperature VESD PRF Condition Min. Typ. -40 All pads, according to human-body model, JEDEC STD 22, method A114 According to charged-device model, JEDEC STD 22, method C101 ESD robustness RF input level VDDMAX Maximum voltage Maximum power supply voltage from any pin with respect to VSS (GND) VDIG Voltage on any digital pins GPIOs, PDn, RESETn, Coex I/F Max. Units +85 C 1000 V 500 V +20 dBm -0.3 3.6 V -0.3 VDDMAX V 17.2. RECOMMENDED OPERATING CONDITIONS The maximum ratings may not be exceeded under any circumstances, not even momentarily and individually, as permanent damage to the module will result. Symbol Parameter TA Ambient operating temperature range VDD 3V3 Supply voltage 4 Condition Min. Extendet grade -30 Voltage on pins 7, 8 (3.3V) I/O supply voltage internally connected to VDD 3.0 Condition Min. 3.3V Operation (VIO = VDD) Typ. Max. Units +70 C 3.3 3.6 V Typ. Max. Units 0.7VDD VDD+0.3 V 3.3V Operation (VIO = VDD) -0.3 0.3VDD V 17.3. DIGITAL PIN CHARACTERISTICS Symbol Parameter VIH High level input voltage5 5 VIL Low level input voltage IOH @ VDD-0.4V High level output current5 3.3V Operation (VIO = VDD) 4 mA IOL @ 0.4V Low level output current5 3.3V Operation (VIO = VDD) 4 mA 4 The supply current must be limited to max. 1A 5 The capacitive load should not be larger than 50 pF for all I/O's when using the default driver strength settings. Generally, large capacitance loads increase the overall current consumption. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION No. DS-9320-2400-102 WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF REV. 0.1 14 of 35 DATE 22.04.2015 17.4. ELECTRICAL CHARACERISTICS The current consumption depends on the user scenario and the setup and timing in the power modes. Assume VDD = 3.3V, Tamb = 25C if nothing else stated 17.4.1. Current consumption Symbol ITX IRX Parameter Current Consumption Active Transmit 6 Active Receive 7 Condition Min. Typ. Max. Units PTX = +18 dBm for 802.11b @ 11 Mbps 430 mA PTX = +15 dBm for 802.11g @ 54 Mbps 370 mA PTX = +13 dBm for 802.11n (20MHz) @ 65 Mbps 350 mA 802.11b @ 11 Mbps 160 mA 802.11g @ 54 Mbps 165 mA 802.11n @ 65 Mbps 170 mA IRXIdle Receive Idle 8 Passive receive state, ready to receive packets, but no active decoding 160 mA IIEEE-PSM IEEE 802.11 PS Radio in "IEEE PS DTIM 1" mode tbd mA IShut-off Shut-off mode MCU and Radio in Power Safe mode tbd mA 17.5. INTERNAL OPERATING FREQUENCIES Symbol Parameter Condition fSYSCLK1 CPU/System/Encryption clock speed fSYSCLK2 fREFCLK1 fREFCLK2 Max. Units Refers to clock speed of WLAN SoC 128 MHz CPU/System clock speed Refers to clock speed of MCU 200 MHz WLAN SoC Crystal fundamental frequency Microcontroller Crystal fundamental frequency Frequency tolerance < 10 ppm over operating temperature and process Frequency tolerance < 10 ppm over operating temperature and process 6 Peak values for specified output power level and data rate with UDP traffic between the AP and Device (STA). 7 Peak values for specified data rate with UDP traffic between the AP and Device (STA).. 8 The device is powered on and is ready to receive packets, but is not actively decoding. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH Min. Typ. 40 MHz 32 MHz www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION No. DS-9320-2400-102 WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF REV. 0.1 15 of 35 DATE 22.04.2015 17.6. COEXISTENCE INTERFACE SPECIFICATION The Coexistence Interface pins are powered from the VIO voltage supply internally connected to VDD = 3.3V. See Chapter 17.3 Digital Pin Characteristics for DC specification. 17.6.1. Marvell(R) 3/4-Wire Timing Data Symbol Parameter Min. Typ. Max. Units T1 Priority[0] info is valid in BT_STATE on and after T1 from BT_REQ rise. 0 1 100 s T2 TxRx Info is valid in BT_STATE on and after T2. The BT_STATE must hold until there is any change of direction in the next slots. 2 19 100 s T3 Time from TxRx Info valid to BCA grant decision (T3 = T7 - T4 - T2 - T8 - T1). 2 40 594 s 2 80 594 s 5 40 600 s 0 15 25 s 8 150 600 s 2 10 100 s T4 T5 T6 T7 T8 BT_GRANTn needs to be valid T4 time before the upcoming slot. BT_GRANTn indicates Tx grant, and may also indicate Rx grant. Once a slot is granted, the subsequent slots are also granted unless there is a change in direction from Rx to Tx. Rx to Tx change always re-arbitrates. TxRx Info for the next slot is valid on and after T5 to the start of the next slot. If direction remains the same for the next slot, then BT_STATE must not change during the current slot. If the direction changes for the next slot, the BT_STATE must change only after the last bit of Bluetooth data is transferred; otherwise the transfer may be disrupted. The BT_REQ signal de-asserts T6 time after last bit of Bluetooth data is transferred. Time from BT_REQ rise to first Bluetooth slot boundary. Bluetooth slot boundary is marked by first bit of Bluetooth data. Optional Priority[1] information is valid in BT_STAT on and after T8. This time parameter only exists if BCA is configured for 2-bit priority on same BT_STATE pin. Otherwise, the start of T2 would come after T1. Ttx Slot time (fixed fpr Bluetooth) 625 s Trx Slot time (fixed fpr Bluetooth) 625 s PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION No. DS-9320-2400-102 WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF REV. 0.1 16 of 35 DATE 22.04.2015 17.6.2. WL_ACTIVE 2/3/4-Wire Timing Data Symbol Parameter If WLAN can be stopped, WL_ACTIVE will de-asser prior to Bluetooth slot start (T1 < T2) If the Bluetooth device samples WL_ACTIVE before starting priority transfer, WL_ACTIVE needs to de-assert earlier than the sampling time. Min. Typ. Units 499 s T1 T2 Time from BT_PRIORITY rise to start of Bluetooth activity. 20 50 499 s T3 Time from end of Bluetooth activity to BT_PRIORITY fall. 0 0 499 s T4 Slot time (fixed fpr Bluetooth) PANASONIC INDUSTRIAL DEVICES EUROPE GMBH 0 Max. 625 s www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION No. DS-9320-2400-102 WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF REV. 0.1 17 of 35 DATE 22.04.2015 17.7. HOST INTERFACE SPECIFICATION 17.7.1. UART0 Interface (Command) UART0 Interface bus signals: Module Pin No Signal Name Description 27 28 TXD for UART0 RXD for UART0 Transmit data output Receive data input Protocol Item Range Default Baudrate Data Bits Parity Bits Stop Bit 300 ~ 1528000 5 ~ 8 (LSB first) 0~4 1 / 1,5 / 2 115200 8 0 1 Comment LSB first Initial setting: One Bit Serial data Start 8 Data bits Stop One Character 17.7.2. UART1 Interface (Data) UART1 Interface bus signals Module Pin No Signal Name Description 9 10 11 12 CTS for UART1 RTS for UART1 TXD for UART1 RXD for UART1 Clear to send Request to send Transmit data output Receive data input Protokol Item Range Default Baudrate Data Bits Parity Bits Stop Bit 300 ~ 1528000 5 ~ 8 (LSB first) 0~4 1 / 1,5 / 2 115200 8 0 1 Comment LSB first PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT No. DS-9320-2400-102 PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF DATE REV. 0.1 18 of 35 22.04.2015 18. RF ELECTRICAL CHARACTERISTICS 18.1. WLAN RADIO SPECIFICATION Parameter Operation mode Specification IEEE 802.11 / IEEE 802.11b Standard Conformance IEEE 802.11g IEEE 802.11n Modulation IEEE 802.11b DSSS / CCK IEEE 802.11g OFDM IEEE 802.11n OFDM @ MCS0~7 and MCS32 (duplicate 6 Mbps) IEEE 802.11 1, 2 Mbps @ DSSS IEEE 802.11b 5.5, 11 Mbps @ DSSS / CCK IEEE 802.11g 6, 9, 12, 18, 24, 36, 48, 54 Mbps Physical layer data rates LGI 6.5, 13, 19.5, 26, 39, 52, 58.5, 65 Mbps SGI 7.2, 14.4, 21.7, 28.9, 43.3, 57.8, 65, 72.2 Mbps LGI 13.5, 27, 40.5, 54, 81, 108, 121.5, 135 Mbps SGI 15, 30, 45, 60, 90, 120, 135, 150 Mbps HT20 Supported data rates IEEE 802.11n MCS0~7 HT40 Supported bandwidth IEEE 802.11n 20, 40 MHz (BW) Supported channel mode operation IEEE 802.11n 20 MHz BW / channel, 40 MHz BW / channel, upper / lower 20 MHz BW @ 40 MHz channel, 20 MHz duplicate legacy BW @ 40 MHz channel Supported Guard Interval IEEE 802.11n 400 ns (SGI), 800 ns (LGI) IEEE 802.11g North America 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11 Europe 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13 Spain 10, 11 France 10, 11, 12, 13 Japan MMK 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13 Supported channel 2.4GHz North America Europe 1-5, 2-6, 3-7, 4-8, 5-9, 6-10, 7-11 IEEE 802.11n Spain France Japan MMK PANASONIC INDUSTRIAL DEVICES EUROPE GMBH - www.pideu.panasonic.de CLASSIFICATION SUBJECT No. DS-9320-2400-102 PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF REV. 0.1 19 of 35 DATE 22.04.2015 18.2. WLAN RF CHARACTERISTICS 18.2.1. RF Characteristics for IEEE 802.11b Assume VDD = 3.3V, Tamb = 25C if nothing else stated 50 Ohm terminal load connected to the RF connector Parameter Condition Min. Typ. Max. Units RF frequency range 2400 2483.5 MHz Carrier frequency tolerance -25 +25 ppm Transmit output power +16 +20 dBm fC 11 MHz -30 dBr fC 22 MHz -50 +18 Spectrum mask Power-on / Power-down ramp 2 s RF Carrier suppression -15 dB 35 % Error Vector Magnitude (EVM) Peak 1 Mbps (DSSS) FER 8% -98 -86 dBm 2 Mbps (DSSS) FER 8% -95 -83 dBm 5.5 Mbps (CCK) FER 8% -91 -79 dBm 11 Mbps (CCK) FER 8% -88 -76 dBm Minimum Receive Sensitivity Maximum Input Level FER 8% -10 dBm Adjacent Channel Rejection FER 8% 35 dB PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION No. DS-9320-2400-102 WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF REV. 0.1 20 of 35 DATE 22.04.2015 18.2.2. RF Characteristics for IEEE 802.11g Assume VDD = 3.3V, Tamb = 25C if nothing else stated 50 Ohm terminal load connected to the RF connector Parameter Condition Min. Typ. Max. Units RF frequency range 2400 2483.5 MHz Carrier frequency tolerance -25 +25 ppm 6 Mbps ~ 36 Mbps +14 +16 +18 dBm 48 Mbps ~ 54 Mbps +13 +15 +17 dBm fC 11 MHz -20 dBr fC 20 MHz -28 dBr fC 30 MHz -40 dBr -15 dB +2 dB BPSK, CR 1/2 (6 Mbps) -5 dB BPSK, CR 3/4 (9 Mbps) -8 dB QPSK, CR 1/2 (12 Mbps) -10 dB QPSK, CR 3/4 (18 Mbps) -13 dB 16-QAM, CR 1/2 (24 Mbps) -16 dB 16-QAM, CR 3/4 (36 Mbps) -19 dB 64-QAM, CR 2/3 (48 Mbps) -22 dB 64-QAM, CR 3/4 (54 Mbps) -25 dB Transmit output power Spectrum mask Transmitter center frequency leakage Transmitter Spectral Flatness -2 Constellation Error (EVM) BPSK, CR 1/2 (6 Mbps) PER 10% -93 -82 dBm BPSK, CR 3/4 (9 Mbps) PER 10% -92 -81 dBm QPSK, CR 1/2 (12 Mbps) PER 10% -90 -79 dBm QPSK, CR 3/4 (18 Mbps) PER 10% -88 -77 dBm 16-QAM, CR 1/2 (24 Mbps) PER 10% -85 -74 dBm 16-QAM, CR 3/4 (36 Mbps) PER 10% -81 -70 dBm 64-QAM, CR 2/3 (48 Mbps) PER 10% -77 -66 dBm 64-QAM, CR 3/4 (54 Mbps) PER 10% -76 -65 dBm -20 dBm Minimum Receive Sensitivity PER 10% Maximum Input Level BPSK, CR 1/2 (6 Mbps) PER 10% 16 dB 64-QAM, CR 3/4 (54 Mbps) PER 10% -1 dB Adjacent channel rejection PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION No. DS-9320-2400-102 WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF REV. 0.1 21 of 35 DATE 22.04.2015 18.2.3. RF Characteristics for IEEE 802.11n (BW 20 MHz) Assume VDD = 3.3V, Tamb = 25C if nothing else stated 50 Ohm terminal load connected to the RF connector Parameter Condition Min. Typ. Max. Units RF frequency range 2400 2483.5 MHz Carrier frequency tolerance -25 +25 ppm Transmit output power Spectrum mask MCS0 ~ MCS2 13 15 17 dBm MCS3 ~ MCS4 12 14 16 dBm MCS5 ~ MCS7 11 13 15 dBm fC 11 MHz -20 dBr fC 20 MHz -28 dBr fC 30 MHz -45 dBr -15 dB +2 dB BPSK, CR 1/2 (MCS0) -5 dB QPSK, CR 1/2 (MCS1) -10 dB QPSK, CR 3/4 (MCS2) -13 dB 16-QAM, CR 1/2 (MCS3) -16 dB 16-QAM, CR 3/4 (MCS4) -19 dB 64-QAM, CR 2/3 (MCS5) -22 dB 64-QAM, CR 3/4 (MCS6) -25 dB 64-QAM, CR 5/6 (MCS7) -27 dB Transmitter center frequency leakage Transmitter Spectral Flatness -2 Constellation Error (EVM) Minimum Receive Sensitivity 6.5 Mbps (MCS0) PER 10% -92 -82 dBm 13 Mbps (MCS1) PER 10% -89 -79 dBm 19.5 Mbps (MCS2) PER 10% -87 -77 dBm 26 Mbps (MCS3) PER 10% -84 -74 dBm 39 Mbps (MCS4) PER 10% -80 -70 dBm 52 Mbps (MCS5) PER 10% -76 -66 dBm 58.5 Mbps (MCS6) PER 10% -75 -65 dBm 65 Mbps (MCS7) PER 10% -74 -64 dBm -20 dBm 9 PER 10% Maximum Input Level Adjacent channel rejection 9 10 65 Mbps (MCS7) PER 10% -2 dB The Minimum Sensitivity levels apply only to non-STBC modes, MCS 0~7, 800 ns LGI and BCC. 10 The Adjacent Channel Rejection levels apply only to non-STBC modes, MCS 0~7, 800 ns LGI and BCC. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION No. DS-9320-2400-102 WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF REV. 0.1 22 of 35 DATE 22.04.2015 18.2.4. RF Characteristics for IEEE 802.11n (BW 40 MHz) Assume VDD = 3.3V, Tamb = 25C if nothing else stated 50 Ohm terminal load connected to the RF connector Parameter Condition Min. Typ. Max. Units RF frequency range 2400 2483.5 MHz Carrier frequency tolerance -25 +25 ppm Transmit output power Spectrum mask MCS0 ~ MCS2 11 13 15 dBm MCS3 ~ MCS4 10 12 14 dBm MCS5 ~ MCS7 9 11 13 dBm fC 21 MHz -20 dBr fC 40 MHz -28 dBr fC 60 MHz -45 dBr -15 dB +2 dB BPSK, CR 1/2 (MCS0) -5 dB QPSK, CR 1/2 (MCS1) -10 dB QPSK, CR 3/4 (MCS2) -13 dB 16-QAM, CR 1/2 (MCS3) -16 dB 16-QAM, CR 3/4 (MCS4) -19 dB 64-QAM, CR 2/3 (MCS5) -22 dB 64-QAM, CR 3/4 (MCS6) -25 dB 64-QAM, CR 5/6 (MCS7) -27 dB Transmitter center frequency leakage Transmitter Spectral Flatness -2 Constellation Error (EVM) 13.5 Mbps (MCS0) PER 10% -89 -79 dBm 27 Mbps (MCS1) PER 10% -86 -76 dBm 40.5 Mbps (MCS2) PER 10% -84 -74 dBm 54 Mbps (MCS3) PER 10% -81 -71 dBm 81 Mbps (MCS4) PER 10% -77 -67 dBm 108 Mbps (MCS5) PER 10% -73 -63 dBm 121.5 Mbps (MCS6) PER 10% -72 -62 dBm 135 Mbps (MCS7) PER 10% -71 -61 dBm -20 dBm Minimum Receive Sensitivity 9 PER 10% Maximum Input Level Adjacent channel rejection 10 135 Mbps (MCS7) PER 10% PANASONIC INDUSTRIAL DEVICES EUROPE GMBH -2 dB www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION No. DS-9320-2400-102 WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF DATE REV. 0.1 23 of 35 22.04.2015 19. SOLDERING TEMPERATURE-TIME PROFILE (FOR REFLOW SOLDERING) 19.1. FOR LEAD SOLDER 10 1s Recommended temp. profile for reflow soldering 30 +20/-10s 235C max. Temp.[C] 220 5C 200C 150 10C 90 30s Time [s] 19.2. FOR LEADFREE SOLDER Our used temp. profile for reflow soldering 30 +20/-10s Temp.[C] 230C -250C max. 220C 150C - 190C 90 30s Time [s] Reflow permissible cycle: 2 Opposite side reflow is prohibited due to module weight. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION No. DS-9320-2400-102 WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF REV. 0.1 24 of 35 DATE 22.04.2015 20. PAN9320 MODULE DIMENSION No. Item Dimension Tolerance 1 Width 13.50 0.30 2 Length 29.00 0.30 3 Height 2.66 0.20 Remark with case 29 ,50 2,66 13 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT No. DS-9320-2400-102 PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF REV. 0.1 25 of 35 DATE 22.04.2015 21. PAN9320 FOOTPRINT OF THE MODULE All dimensions are in millimeters. The outer dimensions have a tolerance of 0.3mm. Top view, Application PCB Top View 24,60 mm 16,90 mm 12,90 mm 30 29 F1 F2 F3 F4 F5 28 27 26 25 E3 E4 E5 D3 D4 D5 40 C1 C2 C3 C4 C5 B1 B2 B3 B4 2,40 mm B5 A1 A2 A3 A4 A5 3 4 5 6 7 8 0,80 mm Ground plane keep out area 17 5,60 mm 0,80 mm 2 19 GND THERMO 2,40 mm 42 20 18 GND THERMO 2,40 mm 1,6 mm D2 GND THERMO 9 10 1,60 mm 11 12 13 14 1,30 mm 2,50 mm 4.25 mm E2 D1 41 0,80 mm 9,55 mm 3,10 mm Chip Antenna E1 39 1 22 21 GND THERMO 13,50 mm 23 0,80 mm 38 0,40 mm 1,70 mm 24 4.25 mm 31 5.00 mm 32 16 15 3,15 mm 33 2,35 mm 37 34 0,25 mm 1,55 mm 35 0,80 mm 1,30 mm 36 0,80 mm 5,70 mm 3,30 mm 29,00 mm PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION No. DS-9320-2400-102 WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF DATE REV. 0.1 26 of 35 22.04.2015 22. CASE MARKING (EXAMPLE FOR PAN9320) 1 3 4 5 6 7 8 PAN9320 2 01/01 ENW49A01A3JF YYWWDLL 12345678 ABCDEFABCDEF FCC ID: T7V-9320 IC: 216Q-9320 10 9 No. Remark 1 PAN9320 (Model Name), see chapter 27 Ordering Information 2 Hardware/Software version 3 Part Number, see Ordering Information, chapter 27 Ordering Information 4 Lot code: YearYear, WeekWeek, Day, LotLot 5 Serial Number (8 digits) 6 WLAN MAC address (12 digits) 7 FCC ID, refer to chapter 29.1 (tbd) 8 IC Canada, refer to chapter 29.2 (tbd) 9 Marking for Pin 1 (Circle 0,15 mm) 10 2D-Code, for internal usage only and can be change without any notice PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT No. DS-9320-2400-102 PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF DATE REV. 0.1 27 of 35 22.04.2015 23. MECHANICAL REQUIREMENTS No. Item 1 Solderability 2 Resistance to soldering heat Limit Condition More than 75% of the soldering area shall be coated by solder It shall be satisfied electrical requirements and not be mechanical damage Reflow soldering with recommendable temperature profile See chapter 19.2 24. RELIABILITY TESTS The measurement should be done after being exposed to room temperature and humidity for 1 hour. Item Limit Condition 1 Vibration test Electrical parameter should be in specification a) Freq.:10~50Hz,Amplitude:1.5mm a) 20min. / cycle,1hrs. each of XYZ axis b) Freq.:30~100Hz, 6G b) 20min. / cycle,1hrs. each of XYZ axis 2 Shock test the same as above Dropped onto hard wood from height of 50cm for 3 times 3 Heat cycle test the same as above -40C for 30min. and +85C for 30min.; each temperature 300 cycles 4 Moisture test the same as above +60C, 90% RH, 300h 5 Low temp. test the same as above -40C, 300h 6 High temp. test the same as above +85C, 300h No. 25. CAUTIONS Failure to follow the guidelines set forth in this document may result in degrading of the product's functions and damage to the product. 25.1. DESIGN NOTES (1) (2) (3) (4) (5) (6) (7) Follow the conditions written in this specification, especially the control signals of this module. The supply voltage must be free of AC ripple voltage (for example from a battery or a low noise regulator output). For noisy supply voltages, provide a decoupling circuit (for example a ferrite in series connection and a bypass capacitor to ground of at least 47uF directly at the module). This product should not be mechanically stressed when installed. Keep this product away from heat. Heat is the major cause of decreasing the life of these products. Avoid assembly and use of the target equipment in conditions where the products' temperature may exceed the maximum tolerance. The supply voltage should not be exceedingly high or reversed. It should not carry noise and/or spikes. Keep this product away from other high frequency circuits. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION No. DS-9320-2400-102 WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF DATE REV. 0.1 28 of 35 22.04.2015 25.2. INSTALLATION NOTES (1) Reflow soldering is possible twice based on the conditions in chapter 15. Set up the temperature at the soldering portion of this product according to this reflow profile. (2) Carefully position the products so that their heat will not burn into printed circuit boards or affect the other components that are susceptible to heat. (3) Carefully locate these products so that their temperatures will not increase due to the effects of heat generated by neighboring components. (4) If a vinyl-covered wire comes into contact with the products, then the cover will melt and generate toxic gas, damaging the insulation. Never allow contact between the cover and these products to occur. (5) This product should not be mechanically stressed or vibrated when reflowed. (6) To repair the board by hand soldering, follow the conditions set forth in this chapter. (7) Do not wash this product. (8) Refer to the recommended pattern when designing a board. (9) Pressing on parts of the metal cover or fastening objects to the metal will cause damage to the unit. (10) For more details on LGA (Land Grid Array) soldering processes refer to the application note. 25.3. USAGE CONDITIONS NOTES (1) (2) (3) (4) (5) (6) (7) Take measures to protect the unit against static electricity. If pulses or other transient loads (a large load applied in a short time) are applied to the products, check and evaluate their operation befor assembly on the final products. Do not use dropped products. Do not touch, damage or soil the pins. Follow the recommended condition ratings about the power supply applied to this product. Electrode peeling strength: Do not add pressure of more than 4.9N when soldered on PCB. Pressing on parts of the metal cover or fastening objects to the metal cover will cause damage. These products are intended for general purpose and standard use in general electronic equipment, such as home appliances, office equipment, information and communication equipment. 25.4. STORAGE NOTES (1) (2) (3) (4) (5) The module should not be stressed mechanically during storage. Do not store these products in the following conditions or the performance characteristics of the product, such as RF performance will be adversely affected: Storage in salty air or in an environment with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NOX Storage in direct sunlight Storage in an environment where the temperature may be outside the range of 5C to 35C range, or where the humidity may be outside the 45 to 85% range. Storage of the products for more than one year after the date of delivery Storage period: Please check the adhesive strength of the embossed tape and soldering after 6 months of storage. Keep this product away from water, poisonous gas and corrosive gas. This product should not be stressed or shocked when transported. Follow the specification when stacking packed crates (max. 10). PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION No. DS-9320-2400-102 WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF DATE REV. 0.1 29 of 35 22.04.2015 25.5. SAFETY CAUTIONS These specifications are intended to preserve the quality assurance of products and individual components. Before use, check and evaluate the operation when mounted on your products. Abide by these specifications, without deviation when using the products. These products may short-circuit. If electrical shocks, smoke, fire, and/or accidents involving human life are anticipated when a short circuit occurs, then provide the following failsafe functions, as a minimum. (1) Ensure the safety of the whole system by installing a protection circuit and a protection device. (2) Ensure the safety of the whole system by installing a redundant circuit or another system to prevent a single fault causing an unsafe status. 25.6. OTHER CAUTIONS (1) (2) (3) (4) (5) (6) (7) This specification sheet is copyrighted. Do not disclose it to a third party. Do not use the products for other purposes than those listed. Be sure to provide an appropriate fail-safe function on your product to prevent an additional damage that may be caused by the abnormal function or the failure of the product. This product has been manufactured without any ozone chemical controlled under the Montreal Protocol. These products are not intended for other uses, other than under the specia l conditions shown below. Before using these products under such special conditions, check their performance and reliability under the said special conditions carefully to determine whether or not they can be used in such a manner. In liquid, such as water, salt water, oil, alkali, or organic solvent, or in places where liquid may splash. In direct sunlight, outdoors, or in a dusty environment In an environment where condensation occurs. In an environment with a high concentration of harmful gas (e.g. salty air, HCl, Cl2, SO2, H2S, NH3, and NOX) If an abnormal voltage is applied due to a problem occurring in other components or circuits, replace these products with new products because they may not be able to provide normal performance even if their electronic characteristics and appearances appear satisfactory. When you have any question or uncertainty, contact Panasonic. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION No. DS-9320-2400-102 WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF DATE REV. 0.1 30 of 35 22.04.2015 26. PACKAGING Mass production status product -- as indicated in Chapter 3 -- will be delivered in the package described below. 26.1. PAN9320 TAPE DIMENSION 26.2. PACKING IN TAPE Empty spaces in component packed area shall be less than two per reel and those spaces shall not be consecutive. Top cover tape shall not be found on reel holes and shall not stick out from reel. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION No. DS-9320-2400-102 WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF DATE REV. 0.1 31 of 35 22.04.2015 26.3. COMPONENT DIRECTION 26.4. REEL DIMENSION PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT No. DS-9320-2400-102 PRODUCT SPECIFICATION WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF REV. 0.1 32 of 35 DATE 22.04.2015 26.5. LABEL FOR PACKAGE The picture shows an example from similar product. -AAA (3P): PAN9320 Company RoHS ENW49A01A3EF xy/ab 500 Country of Origin: Slovakia (1T) Lot code [YYWWDLL-AAA] YY year WW normal calendar week D day L line identifier, if more as one L lot identifier per day AAA number of the reel (example 001, 002,..., 999) Example from above: printed 08 printed 01 printed 5 (Friday) printed 1 printed 1 printed 001 (1P) Customer Order Code, if any, otherwise company name will be printed (2P) Panasonic Order Code: ENW49A01x3EF (see chapter 27 Ordering Information) (3P) Model type, (see chapter 27 Ordering Information) (9D) Date code as [YYWW] (Q) Quantity [XXXX], variable max. 500 (HW/SW) Hardware/Software Release 26.6. TOTAL PACKAGE moisture-sensitive print (already exist on barrier bag) barcode label barrier bag sealed desiccant 1) 2) moisture indicator barcode label 1) quantity of desiccant according to calculation 2) optional: desiccant placed into the corner of the barrier bag inner carton box size 340 x 340 x 41 mm PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION No. DS-9320-2400-102 WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF DATE REV. 0.1 33 of 35 22.04.2015 27. ORDERING INFORMATION Ordering part number Model type Description MOQ ENW49A01A3EF PAN9320 WLAN IEEE 802.11 b/g/n 2.4GHz Full Embedded Module with ceramic chip-antenna 500 (1) The PAN9320 will be delivered with a preinstalled embedded Web-Stack, see [1] PAN9320 Software-Guide Notes: (1) Abbreviation for Minimum Order Quantity (MOQ). The standard MOQ for mass production is 500 pieces, fewer only on customer demand. Samples for evaluation can be delivered at any quantity via the distribution channels. 28. ROHS DECLARATION Declaration of environmental compatibility for supplied products: Hereby we declare to our best present knowledge based on declaration of our suppliers that this product does not contain the following substances which are banned by Directive 2002/95/EC (RoHS) or contains a maximum concentration of 0.1% by weight in homogeneous materials for Lead and lead compounds Mercury and mercury compounds Chromium (VI) PBB (polybrominated biphenyl) category PBDE (polybrominated biphenyl ether) category And a maximum concentration of 0.01% by weight in homogeneous materials for Cadmium and cadmium compounds PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION No. DS-9320-2400-102 WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF DATE REV. 0.1 34 of 35 22.04.2015 29. REGULATORY INFORMATION 29.1. FCC FOR US Under preparation 29.2. INDUSTRY CANADA CERTIFICATION Under preparation 29.3. EUROPEAN R&TTE DECLARATION OF CONFORMITY Under preparation PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de CLASSIFICATION SUBJECT PRODUCT SPECIFICATION No. DS-9320-2400-102 WI-FI IEEE 802.11 BGN FULL EMBEDDED MODULE PAGE CUSTOMER'S CODE PANASONIC'S CODE PAN9320 ENW49A01A3EF DATE REV. 0.1 35 of 35 22.04.2015 30. GENERAL INFORMATION (c) Panasonic Industrial Devices Europe GmbH 2015. All rights reserved. This product description does not lodge the claim to be complete and free of mistakes. Please contact the related product manager in every case. If ES samples are delivered to the customer, these samples have the status Engineering Samples. This means, the design of this product is not yet concluded. Engineering Samples may be partially or fully functional, and there may be differences to be published Data Sheet. Engineering Samples are not qualified and are not to be used for reliability testing or series production. Disclaimer: Customer acknowledges that samples may deviate from the Data Sheet and may bear defects due to their status of development and the lack of qualification mentioned above. Panasonic rejects any liability or product warranty for Engineering Samples. In particular, Panasonic disclaims liability for damages caused by the use of the Engineering Sample other than for Evaluation Purposes, particularly the installation or integration in another product to be sold by Customer, deviation or lapse in function of Engineering Sample, improper use of Engineering Samples. Panasonic Industrial Devices Europe GmbH disclaimes any liability for consequential and incidental damages. In case of any questions, please contact your local sales partner or the related product manager. 31. LIFE SUPPORT POLICY This Panasonic Industrial Devices Europe GmbH product is not designed for use in life support appliances, devices, or systems where malfunction can reasonably be expected to result in a significant personal injury to the user, or as a critical component in any life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Panasonic Industrial Devices Europe GmbH for any damages resulting. PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de