Printed in USA 07/06 P/N 128190
Model PPLIM Light Interface Module
DC-Powered Interface for PresencePLUS ® Lights
Features
• Low-cost strobe interface between user’s hardware and PresencePLUS lights
• Separate Strobe Signal inputs:
– 5V TTL signal
– 8–30V dc signal (switch-selectable current sinking/NPN or current sourcing/PNP)
• Two Light Strobe outputs:
– 5V “Active Low” (non-inverting)
– 5V “Active High” (inverting)
• LED indicators for Power and Strobe Signal inputs
• Easy-to-adjust 45° screw terminals for electrical wiring
• Simple 35 mm DIN-rail-mount or wall-mount configuration
Overview
The model PPLIM PresencePLUS Light Interface Module is a passive DIN-rail-mount or
wall-mount module. It enables use of Banner PresencePLUS LED lights with strobe signal
sources other than Banner machine vision sensors, for example, high-end vision systems,
PLCs, photoelectric sensors, or proximity sensors.
Installation
For mounting to a flat surface, unscrew one end cap, slide the DIN clips off of the
housing, and replace the end cap. Use the screw-holes in the end caps for mounting to a
flat surface.
Figure 1. Features
Power LED
5V Strobe
LED
8-30V Strobe
LED
Input Terminal
Block
NPN/PNP
Select Switch
PresencePLUS
Light Terminal
Block
Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN USA 55441 • Phone: 763.544.3164 • www.bannerengineering.com • Email: sensors@bannerengineering.com
Models PPLIM.. PresencePLUS Light Interface Module
P/N 128190
WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for one year. Banner Engineering Corp. will repair
or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty
period. This warranty does not cover damage or liability for the improper application of Banner products. This warranty is in lieu of any
other warranty either expressed or implied.
Terminal Block Wiring Tables
“Input” Terminal Block
“PresencePLUS Light” Terminal Block
Pin Color Description
1Brown 24V dc
2Blue OV dc (Common)
3Black 8-30V Strobe
4Pink 5V Strobe
Pin Color Description
1Brown 24V dc
2Blue OV dc (Common)
3White 5V Active low (non-inverting)
4Yellow 5V Active high (inverting)
Dimensions
2X 2.7 mm
(0.11")
52.5 mm
(2.07")
2X 11.8 mm (0.46")
2X R 2.7 mm
(R 0.11")
43.2 mm
(1.70")
62.6 mm
(2.46")
28.7 mm
(1.13")
86.4 mm
(3.40")
29.5 mm
(1.16")
49.5 mm
(1.95")
17.5 mm
(0.69")
Specifications
Input Supply Voltage 24V dc ±10%
Strobe Output Non-Inverting “Active Low”: 5V @ 10 mA max.
Inverting “Active High”: 5V @ 10 mA max.
Adjustments NPN / PNP Select switch is dedicated to “8-30V Strobe” input only.
When using “5V Strobe” input, put NPN / PNP Select switch in PNP position.
Indicator LEDs Power
Green: Power ON
5V Strobe
Green: Active
8-30V Strobe
Green: Active
Construction PCB circuit board; PVC housing, polyamide end caps and DIN rail mounting hardware
Environmental Rating IEC IP00: NEMA 1
Connections Terminal Strip: Accepts 12 to 24 gauge wire
Operating Conditions Temperature: 0° to +50° C (+32° to +122° F)
Max. Relative Humidity: 90% (non-condensing)
Weight Approximately 45 grams (0.1 lb.)
