PSC05-11SURKWA 12.7 mm (0.5 inch) 16 Segment Single Digit Alphanumeric Display DESCRIPTIONS z z z z PACKAGE DIMENSIONS The Hyper Red source color devices are made with AlGaInP on GaAs substrate Light Emitting Diode Electrostatic discharge and power surge could damage the LEDs It is recommended to use a wrist band or anti-electrostatic glove when handling the LEDs All devices, equipments and machineries must be electrically grounded FEATURES z z z z z z z t h 0.5 inch character height Low current operation High contrast and light output Easy mounting on P.C. boards or sockets Mechanically rugged Standard: gray face, white segment RoHS compliant g in APPLICATIONS z z z z Home and smart appliances Display time and digital combination Industrial and instrumental applications Numeric status ATTENTION g i r b K Observe precautions for handling electrostatic discharge sensitive devices Notes: 1. All dimensions are in millimeters (inches), Tolerance is 0.25(0.01")unless otherwise noted. 2. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. SELECTION GUIDE Part Number PSC05-11SURKWA Emitting Color (Material) Hyper Red (AlGaInP) Iv (ucd) @ 10mA [1] Lens Type Description Min. Typ. 52000 110000 Common Cathode, Rt. Hand Decimal White Diffused *14000 *31000 Notes: 1. Luminous intensity / luminous Flux: +/-15%. * Luminous intensity value is traceable to CIE127-2007 standards. (c) 2018 Kingbright. All Rights Reserved. Spec No: DSAK2842 / 1311000335 Rev No: V.8A Date: 03/16/2018 Page 1 / 4 PSC05-11SURKWA ELECTRICAL / OPTICAL CHARACTERISTICS at TA=25C Value Parameter Symbol Wavelength at Peak Emission IF = 10mA Emitting Color Unit Typ. Max. peak Hyper Red 645 - nm dom [1] Hyper Red 630 - nm Spectral Bandwidth at 50% REL MAX IF = 10mA Hyper Red 28 - nm Capacitance C Hyper Red 35 - pF Forward Voltage IF = 10mA VF [2] Hyper Red 1.85 2.35 V Reverse Current (VR = 5V) IR Hyper Red - 10 uA Dominant Wavelength IF = 10mA t h Notes: 1. The dominant wavelength (d) above is the setup value of the sorting machine. (Tolerance d : 1nm. ) 2. Forward voltage: 0.1V. 3. Wavelength value is traceable to CIE127-2007 standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. K g in g i r b ABSOLUTE MAXIMUM RATINGS at TA=25C Parameter Value Unit PD 75 mW Reverse Voltage VR 5 V Junction Temperature Tj 115 C Operating Temperature Top -40 to +85 C Storage Temperature Tstg -40 to +85 C DC Forward Current IF 30 mA IFM [1] 185 mA - 3000 V Power Dissipation Peak Forward Current Electrostatic Discharge Threshold (HBM) Symbol Lead Solder Temperature [2] 260C For 3-5 Seconds Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. 2mm below package base. 3. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity - Ref JEDEC/JESD625-A and JEDEC/J-STD-033. (c) 2018 Kingbright. All Rights Reserved. Spec No: DSAK2842 / 1311000335 Rev No: V.8A Date: 03/16/2018 Page 2 / 4 PSC05-11SURKWA TECHNICAL DATA RELATIVE INTENSITY vs. WAVELENGTH Red Ta = 25 C 80% 60% 40% 20% 0% 350 400 450 500 550 600 Wavelength (nm) 650 700 750 800 t h HYPER RED Forward Current vs. Forward Voltage Luminous Intensity vs. Forward Current Forward current (mA) Ta = 25 C 16 12 8 4 0 1.6 1.7 1.8 1.9 2.0 Forward voltage (V) 2.1 g i r 2.5 Permissible forward current (mA) Luminous intensity normalised at 10 mA 20 Ta = 25 C 2.0 b g 1.5 1.0 n i K 0.5 0.0 0 4 8 12 16 Forward current (mA) RECOMMENDED WAVE SOLDERING PROFILE Luminous Intensity vs. Ambient Temperature Forward Current Derating Curve 20 50 40 30 20 10 0 -40 -20 0 20 40 60 80 100 Ambient temperature (C) Luminous intensity normalised at Ta = 25 C Relative Intensity (a. u.) 100% 2.5 2.0 1.5 1.0 0.5 0.0 -40 -20 0 20 40 60 80 100 Ambient temperature (C) Soldering General Notes 1. Through-hole displays are incompatible with reflow soldering. 2. If components will undergo multiple soldering processes, or other processes where the components may be subjected to intense heat, please check with Kingbright for compatibility. CLEANING Notes: 1. Recommend pre-heat temperature of 105C or less (as measured with a thermocouple attached to the LED pins) prior to immersion in the solder wave with a maximum solder bath temperature of 260C 2. Peak wave soldering temperature between 245C ~ 255Cfor 3 sec (5 sec max). 3. Do not apply stress to the epoxy resin while the temperature is above 85C. 4. Fixtures should not incur stress on the component when mounting and during soldering process. 5. SAC 305 solder alloy is recommended. 6. No more than one wave soldering pass. 7. During wave soldering, the PCB top-surface temperature should be kept below 105C. 1. Mild "no-clean" fluxes are recommended for use in soldering. 2. If cleaning is required, Kingbright recommends to wash components with water only. Do not use harsh organic solvents for cleaning because they may damage the plastic parts . 3. The cleaning process should take place at room temperature and the devices should not be washed for more than one minute. 4. When water is used in the cleaning process, Immediately remove excess moisture from the component with forced-air drying afterwards. (c) 2018 Kingbright. All Rights Reserved. Spec No: DSAK2842 / 1311000335 Rev No: V.8A Date: 03/16/2018 Page 3 / 4 PSC05-11SURKWA PACKING & LABEL SPECIFICATIONS THROUGH HOLE DISPLAY MOUNTING METHOD Lead Forming Do not bend the component leads by hand without proper tools. The leads should be bent by clinching the upper part of the lead firmly such that the bending force is not exerted on the plastic body. t h g i r b Installation 1. The installation process should not apply stress to the lead terminals. 2. When inserting for assembly, ensure the terminal pitch matches the substrate board's hole pitch to prevent spreading or pinching the lead terminals. (Fig.1) 3. The component shall be placed at least 5mm from edge of PCB to avoid damage caused excessive heat during wave soldering.(Fig.2) g in K CIRCUIT DESIGN NOTES 1. Protective current-limiting resistors may be necessary to operate the LEDs within the specified range. 2. LEDs mounted in parallel should each be placed in series with its own current-limiting resistor.(Fig.3) 3. The driving circuit should be designed to protect the LED against reverse voltages and transient voltage spikes when the circuit is powered up or shut down. 4. The safe operating current should be chosen after considering the maximum ambient temperature of the operating environment. 5. Prolonged reverse bias should be avoided, as it could cause metal migration, leading to an increase in leakage current or causing a short circuit. PRECAUTIONARY NOTES 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.kingbright.com/application_notes (c) 2018 Kingbright. All Rights Reserved. Spec No: DSAK2842 / 1311000335 Rev No: V.8A Date: 03/16/2018 Page 4 / 4