Agilent MGA-725M4 Low Noise Amplifier with Bypass Switch In Miniature Leadless Package Data Sheet Features * Operating frequency: 0.1 GHz ~ 6.0 GHz Description Agilent Technologies's MGA-725M4 is an economical, easy-to-use GaAs MMIC Low Noise Amplifier (LNA), which is designed for an adaptive CDMA receiver LNA and adaptive CDMA transmit driver amplifier. The MGA-725M4 features a typical noise figure of 1.4 dB and 14.4 dB associated gain from a single stage, feedback FET amplifier. The output is internally matched to 50. The input is optimally internally matched for lowest noise figure into 50. The input may be additionally externally matched for low VSWR through the addition of a single series inductor. When set into the bypass mode, both input and output are internally matched to 50. Simplified Schematic The MGA-725M4 offers an integrated solution of LNA with adjustable IIP3. The IIP3 can be fixed to a desired current level for the receiver's linearity requirements. The LNA has a bypass switch function, which sets the current to zero and provides low insertion loss. The bypass mode also boosts dynamic range when high level signal is being received. For the CDMA driver amplifier applications, the MGA-725M4 provides suitable gain and linearity to meet the ACPR requirement when the handset transmits the highest power. When transmitting lower power, the MGA-725M4 can be bypassed, saving the drawing current. The MGA-725M4 is a GaAs MMIC, processed on Agilent's cost effective PHEMT (Pseudomorphic High Electron Mobility Transistor). It is housed in the MiniPak 1412 package. It is part of the Agilent Technologies CDMAdvantage RF chipset. * Noise figure: 1.2 dB at 800 MHz 1.4 dB at 1900 MHz * Gain: 17.5 dB at 800 MHz 15.7 dB at 1900 MHz * Bypass switch on chip Loss = typ 1.6 dB (Id < 5 A) IIP3 = +10 dBm * Adjustable Input IP3: +2 to +14.7 dBm * Miniature package: 1.4 mm x 1.2 mm 2.7 V to 5.0 V operation Applications * CDMA (IS-95, J-STD-008) Receiver LNA * Transmit Driver Amp * TDMA (IS-136) handsets MiniPak 1.4 mm x 1.2 mm Package Ax Pin Connections and Package Marking Ax Control Input & Vref Output & Vd INPUT GainFET GND GND OUTPUT GROUND GROUND MGA-725M4 Absolute Maximum Ratings [1] Symbol Parameter Units Absolute Maximum Operation Maximum Vd Maximum Input to Output Voltage V 5.5 4.2 Vgs Maximum Input to Ground DC Voltage V +.3 -5.5 +.1 -4.2 Id Supply Current mA 70 60 Pd Power Dissipation [1,2] mW 300 250 Pin CW RF Input Power dBm +20 +13 Tj Junction Temperature C 170 150 TSTG Storage Temperature C -65 to +150 -40 to +85 Thermal Resistance: [2] jc = 180C/W Notes: 1. Operation of this device in excess of any of these limits may cause permanent damage. 2. Tcase = 25C. Electrical Specifications, Tc = +25C, Zo = 50, Id = 20 mA, Vd = 3V, unless noted. Units Min. Typ. Max. Id = 20 mA V -0.65 -0.51 -0.37 0.035 f = 2.0 GHz Vd = 3.0V (= Vds - Vgs) Id = 20 mA dB 1.4 1.8 0.06 f = 2.0 GHz Vd = 3.0V (= Vds - Vgs) Id = 20 mA dB 13.5 14.4 15.5 0.42 dB 8.5 9.9 Symbol Parameter and Test Condition Vgs test [1] f = 2.0 GHz Vd = 3.0V (Vds = 2.5V) NF test [1] test [1] IIP3 test [1] Ga f = 2.04 GHz Vd = 3.0V (= Vds - Vgs) Id = 20 mA test [1,4] f = 2.0 GHz Vd = 3.0V (Vds = 0V, Vgs = -3V) Id = 0.0 mA dB 1.6 Ig test [1,4] f = 2.0 GHz Vd = 3.0V (Vds = 0V, Vgs = -3V) Id = 0.0 mA A 2.0 Nfo [2] Minimum Noise Figure As measured in Figure 2 Test Circuit (Computed from s-parameter and noise parameter performance as measured in a 50 impedance fixture) f = 1.0 GHz f = 1.5 GHz f = 2.0 GHz f = 2.5 GHz f = 4.0 GHz f = 6.0 GHz dB 1.2 1.2 1.3 1.3 1.4 1.6 Gain[2] Associated Gain at Nfo As measured in Figure 2 Test Circuit (Computed from s-parameter and noise parameter performance as measured in a 50 impedance fixture) f = 1.0 GHz f = 1.5 GHz f = 2.0 GHz f = 2.5 GHz f = 4.0 GHz f = 6.0 GHz dB 17.6 16.6 15.7 14.8 12.8 10.6 P1dB[1] Output Power at 1 dB Gain Compression As measured in Figure 1 Test Circuit Frequency = 2.04 GHz Id = 0 mA Id = 5 mA Id = 10 mA Id = 20 mA Id = 40 mA Id = 60 mA dBm 15.2 3.4 9.14 13.13 15.25 16.16 Id = 0 mA Id = 5 mA Id = 10 mA Id = 20 mA Id = 40 mA Id = 60 mA dBm IL IIP3 [1] Input Third Order Intercept Point As measured in Figure 1 Test Circuit Frequency = 2.04 GHz 35 3.1 6.6 9.9 13.0 14.7 0.35 3.5 0.07 2.0 0.53 0.35 RLin[1] Input Return Loss as measured in Fig. 1 f = 2.0 GHz dB -8.2 0.41 RLout[1] Output Return Loss as measured in Fig. 1 f = 2.0 GHz dB -15 1.3 ISOL[1] Isolation |S12|2 f = 2.0 GHz dB -23.4 0.4 As measured in Fig. 2 Notes: 1. Standard deviation and typical data as measured in the test circuit of Figure 1. Data based on 500 part sample size from 3 wafer lots. 2. Typical data computed from S-parameter and noise parameter data measured in a 50 system. 3. Vd = total device voltage = Vdg 4. Bypass mode voltages shown are used in production test. For source resistor biasing, Bypass mode is set by opening the source resistor. 2 1000 pF RF Input Ax 27 nH RF Output 27 nH 2.7 nH 1000 pF Ax 100 pF 47 pF 100 pF Vd ICM Fixture RF Input Bias Tee Vds 1.2 nH Vgs Bias Tee RF Output 47 pF Vgs Figure 2. MGA-725M4 50 Test Circuit for S, Noise, and Power Parameters. Figure 1. MGA-725M4 Production Test Circuit. MGA-725M4 Typical Performance Frequency = 2.0 GHz, Tc = 25C, Zo = 50, Vd = 3V, Id = 20 mA unless stated otherwise. All data as measured in Figure 2 test system (input and output presented to 50). 18 3.0 14 16 2.5 10 GAIN (dB) 1.5 INPUT IP3 (dB) 12 2.0 NF (dB) 12 14 10 8 6 1.0 0 1 2 3 4 5 2.7V 3.0V 3.3V 2 0 0 6 0 1 FREQUENCY (GHz) 3 4 5 2 18 16 16 14 14 12 12 10 8 4 -40C +25C +85C 3 4 5 0 6 0 1 FREQUENCY (GHz) 2 3 4 5 5 6 8 6 0 6 -40C +25C +85C 0 1 2 3 4 5 6 FREQUENCY (GHz) Figure 8. Input Third Order Intercept Point vs. Frequency and Temperature. 0 14 Input Output 4 2 Figure 7. Gain vs. Frequency and Temperature. 8 3 10 FREQUENCY (GHz) Figure 6. Noise Figure vs. Frequency and Temperature. 2 4 -40C +25C +85C 2 0 2 1 Figure 5. Input Third Order Intercept Point vs. Frequency and Voltage. 18 6 1 1 0 FREQUENCY (GHz) INPUT IP3 (dBm) GAIN (dB) 3 0 0 6 Figure 4. Gain vs. Frequency and Voltage. 4 NF (dB) 2 2.7V 3.0V 3.3V 2 FREQUENCY (GHz) Figure 3. Noise Figure vs. Frequency and Voltage. 12 INSERTION LOSS (dB) -1 6 10 VSWR (LNA) VSWR (LNA) 6 4 4 2.7V 3.0V 3.3V 0.5 4 8 6 4 2 0 0 1 2 3 4 5 FREQUENCY (GHz) Figure 9. LNA on (Switch off) VSWR vs. Frequency. 6 0 -2 -3 -4 Input Output 2 3 8 -40C +25C +85C -5 0 1 2 3 4 5 FREQUENCY (GHz) Figure 10. LNA off (Switch on) VSWR vs. Frequency. 6 0 1 2 3 4 5 FREQUENCY (GHz) Figure 11. Insertion Loss (Switch on) vs. Frequency and Temperature. 6 MGA-725M4 Typical Performance, continued Frequency = 2.0 GHz, Tc = 25C, Zo = 50, Vd = 3V, Id = 20 mA unless stated otherwise. All data as measured in Figure 2 test system (input and output presented to 50). 14 14 12 12 10 10 18 16 8 6 4 8 6 2.7V 3.0V 3.3V 0 1 2 3 4 5 0 8 6 6 0 1 2 3 4 5 Figure 13. Output Power at 1 dB Compression vs. Frequency and Temperature. 2 18 16 16 14 14 12 12 10 8 4 -40C +25C +85C 0 0 20 40 60 0 80 0 20 Id CURRENT (mA) 40 5 6 6 60 -40C +25C +85C 2 0 80 0 20 40 60 80 Id CURRENT (mA) 14 16 4 4 Figure 16. Associated Gain vs. Current and Temperature. 18 3 8 Id CURRENT (mA) Figure 15. Noise Figure vs. Current and Temperature. 2 10 -40C +25C +85C 2 1 Figure 14. Input Third Order Intercept Point vs. Frequency and Current. 18 6 1 0 FREQUENCY (GHz) INPUT IP3 (dBm) GAIN (dB) 3 0 6 Figure 12. Output Power at 1 dB Compression vs. Frequency and Voltage. 4 10 mA 20 mA 40 mA 2 FREQUENCY (GHz) NF (dB) 10 4 2.7V 3.0V 3.3V 2 FREQUENCY (GHz) Figure 17. Input Third Intercept Point vs. Current and Temperature. 1.00 Input Output Gamma 12 14 0.80 10 VSWR 10 8 0.60 8 Vref (V) 12 P1dB (dBm) 12 4 2 0 INPUT IP3 (dBm) P1dB (dBm) P1dB (dBm) 14 6 0.40 6 4 4 -40C +25C +85C 2 0 0 20 40 60 80 Id CURRENT (mA) Figure 18. Output Power at 1 dB Compression vs. Current and Temperature. 4 0 -40C +25C +85C 0.20 2 0 0 10 20 30 40 50 60 Id CURRENT (mA) Figure 19. LNA on VSWR and Gamma Opt vs. Current. 0 10 20 30 40 50 60 Id CURRENT (mA) Figure 20. Control Voltage vs. Current and Temperature. MGA-725M4 Typical Scattering Parameters: Bypass Mode Tc = 25C, Vd = 3.0 V, Id = 0 mA, Zo = 50 (test circuit of Figure 2) Freq (GHz) S11 Mag. S11 Ang. S21 Mag. S21 Ang. S12 Mag. S12 Ang. S22 Mag. S22 Ang. S11 (dB) S21 (dB) S12 (dB) S22 (dB) 0.1 0.5 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0 0.991 0.741 0.580 0.536 0.498 0.468 0.442 0.418 0.395 0.378 0.362 0.349 0.334 0.326 0.357 0.345 0.338 0.326 0.321 0.319 0.288 0.272 0.263 0.256 0.249 0.243 0.229 0.227 0.218 0.221 0.224 -11.1 -44.1 -5.8 -61.8 -64.6 -66.8 -69.2 -70.9 -72.6 -74.7 -76.0 -77.6 -78.9 -79.9 -85.4 -86.0 -86.6 -87.7 -87.9 -88.9 -93.8 -97.0 -101.4 -106.1 -110.9 -114.8 -117.1 -125.3 -130.1 -137.5 -144.2 0.175 0.592 0.710 0.733 0.751 0.764 0.775 0.783 0.793 0.797 0.799 0.805 0.809 0.811 0.826 0.826 0.825 0.826 0.825 0.825 0.820 0.816 0.810 0.807 0.800 0.793 0.781 0.774 0.764 0.758 0.749 74.9 37.9 22.8 18.9 15.4 12.5 9.7 7.1 4.7 2.7 0.5 -1.5 -3.3 -5.1 -8.5 -10.2 -11.5 -13.2 -14.7 -14.6 -21.2 -27.4 -33.5 -39.3 -45.2 -50.7 -57.0 -62.6 -68.1 -73.5 -79.1 0.175 0.593 0.709 0.732 0.750 0.763 0.774 0.783 0.791 0.796 0.800 0.805 0.809 0.811 0.827 0.827 0.825 0.825 0.824 0.824 0.820 0.815 0.811 0.806 0.800 0.795 0.783 0.773 0.768 0.760 0.753 75.5 38.1 22.9 19.0 15.6 12.4 9.8 7.3 5.0 2.7 0.7 -1.3 -3.1 -5.1 -8.3 -10.0 -11.5 -12.9 -14.4 -14.6 -21.4 -27.4 -33.6 -39.2 -45.2 -50.7 -57.0 -62.6 -67.9 -73.2 -78.9 0.943 0.624 0.470 0.429 0.400 0.371 0.346 0.328 0.309 0.293 0.281 0.267 0.258 0.247 0.243 0.238 0.230 0.228 0.222 0.218 0.206 0.198 0.195 0.192 0.190 0.191 0.260 0.256 0.252 0.243 0.230 -15.1 -51.1 -64.1 -67.3 -69.6 -72.3 -74.0 -75.8 -77.2 -78.2 -79.5 -80.4 -80.9 -81.8 -86.5 -87.8 -88.5 -89.3 -90.6 -90.1 -94.6 -98.8 -103.8 -108.9 -114.5 -119.7 -138.9 -146.5 -153.6 -159.8 -166.5 -0.08 -2.61 -4.74 -5.41 -6.05 -6.60 -7.09 -7.58 -8.06 -8.45 -8.84 -9.14 -9.53 -9.74 -8.96 -9.25 -9.43 -9.73 -9.87 -9.92 -10.81 -11.31 -11.59 -11.84 -12.07 -12.30 -12.81 -12.88 -13.25 -13.11 -12.98 -15.12 -4.55 -2.97 -2.70 -2.49 -2.34 -2.22 -2.12 -2.02 -1.98 -1.94 -1.88 -1.84 -1.82 -1.66 -1.66 -1.67 -1.66 -1.67 -1.67 -1.72 -1.76 -1.83 -1.86 -1.94 -2.01 -2.14 -2.23 -2.34 -2.40 -2.51 -15.16 -4.54 -2.99 -2.71 -2.50 -2.35 -2.22 -2.13 -2.04 -1.98 -1.94 -1.89 -1.84 -1.82 -1.65 -1.65 -1.67 -1.67 -1.69 -1.68 -1.72 -1.77 -1.82 -1.88 -1.93 -2.00 -2.13 -2.23 -2.30 -2.39 -2.46 -0.51 -4.09 -6.57 -7.34 -7.95 -8.61 -9.21 -9.68 -10.19 -10.65 -11.03 -11.46 -11.75 -12.13 -12.29 -12.47 -12.77 -12.86 -13.06 -13.24 -13.74 -14.06 -14.18 -14.33 -14.41 -14.39 -11.69 -11.83 -11.99 -12.28 -12.75 5 MGA-725M4 Typical Scattering Parameters and Noise Parameters TC = 25C, Vd = 3.0V, Id = 5 mA, ZO = 50 (test circuit of Figure 2) Freq (GHz) S11 Mag. S11 Ang. S21 Mag. S21 Ang. S12 Mag. S12 Ang. S22 Mag. S22 Ang. S21 (dB) RLin (dB) RLout (dB) Gmax (dB) Isolation (dB) 0.10 0.50 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50 1.60 1.70 1.80 1.90 2.00 2.10 2.20 2.30 2.40 2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00 0.83 0.73 0.71 0.71 0.69 0.69 0.68 0.67 0.67 0.66 0.66 0.66 0.66 0.65 0.65 0.65 0.64 0.64 0.64 0.64 0.63 0.62 0.61 0.60 0.60 0.59 0.57 0.58 0.56 0.53 0.54 -8 -24 -35 -39 -42 -45 -49 -52 -55 -59 -62 -65 -68 -71 -74 -77 -80 -82 -85 -88 -100 -112 -123 -133 -142 -151 -160 -162 -174 175 170 4.17 4.32 4.19 4.14 4.09 4.03 3.99 3.94 3.89 3.83 3.79 3.74 3.69 3.63 3.58 3.54 3.50 3.43 3.39 3.35 3.12 2.91 2.72 2.55 2.40 2.27 2.15 1.93 1.88 1.83 1.77 175 164 156 153 151 148 146 143 141 139 136 134 132 130 127 125 123 121 119 117 107 98 90 82 74 67 59 49 46 40 34 0.05 0.06 0.06 0.06 0.07 0.07 0.07 0.07 0.07 0.08 0.08 0.08 0.08 0.08 0.09 0.09 0.09 0.09 0.10 0.10 0.11 0.12 0.12 0.13 0.13 0.14 0.14 0.14 0.14 0.15 0.15 20 13 18 19 20 22 23 23 24 25 25 26 26 26 26 26 27 26 26 26 24 22 20 18 15 13 9 7 5 3 1 0.58 0.51 0.51 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.49 0.49 0.49 0.49 0.49 0.48 0.48 0.48 0.47 0.47 0.46 0.44 0.43 0.42 0.40 0.39 0.38 0.38 0.36 0.36 0.35 -7 -13 -19 -21 -23 -26 -28 -30 -32 -34 -36 -38 -40 -42 -44 -46 -48 -50 -52 -54 -62 -70 -78 -85 -91 -97 -109 -123 -128 -133 -134 12.4 12.7 12.4 12.3 12.2 12.1 12.0 11.9 11.8 11.7 11.6 11.5 11.3 11.2 11.1 11.0 10.9 10.7 10.6 10.5 9.9 9.3 8.7 8.1 7.6 7.1 6.6 5.7 5.5 5.2 4.9 -1.6 -2.7 -3.0 -3.0 -3.2 -3.3 -3.4 -3.5 -3.5 -3.6 -3.6 -3.7 -3.7 -3.7 -3.8 -3.8 -3.8 -3.9 -3.9 -3.9 -4.0 -4.2 -4.3 -4.4 -4.5 -4.6 -4.9 -4.8 -5.0 -5.5 -5.4 -4.7 -5.8 -5.9 -6.0 -6.0 -6.0 -6.0 -6.0 -6.1 -6.1 -6.2 -6.2 -6.2 -6.3 -6.3 -6.4 -6.5 -6.4 -6.5 -6.6 -6.8 -7.1 -7.4 -7.6 -7.9 -8.2 -8.4 -8.5 -8.8 -8.9 -9.1 18.7 16.6 16.5 16.6 16.5 16.7 16.7 17.4 17.3 17.1 16.9 16.7 16.5 16.4 16.2 16.0 15.9 15.7 15.5 15.4 14.7 14.0 13.5 13.0 12.6 12.2 11.8 11.0 10.0 8.9 8.6 -25.8 -24.4 -24.0 -23.9 -23.6 -23.3 -23.2 -23.0 -22.7 -22.5 -22.2 -21.9 -21.7 -21.5 -21.3 -21.1 -20.9 -20.6 -20.4 -20.3 -19.5 -18.8 -18.3 -17.9 -17.5 -17.2 -17.0 -17.3 -16.9 -16.6 -16.4 Freq (GHz) NFmin (dB) GAMMA OPT Mag Ang Rn Ga (dB) 0.8 0.9 1.0 1.5 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 1.24 1.26 1.34 1.42 1.45 1.48 1.53 1.56 1.58 1.58 1.58 1.61 1.63 1.69 1.69 1.74 1.80 1.81 1.89 0.40 0.40 0.36 0.33 0.30 0.29 0.26 0.24 0.23 0.24 0.23 0.23 0.23 0.24 0.26 0.26 0.27 0.28 0.32 16.5 14.5 13.9 13.0 12.6 12.3 11.9 11.6 11.3 11.4 10.9 10.7 10.1 9.5 9.1 8.8 7.8 7.2 6.4 16.0 15.3 15.0 14.4 14.0 13.8 13.3 13.2 13.0 12.9 12.8 12.6 12.1 11.5 11.0 10.3 9.8 9.3 8.7 6 30 34 42 53 58 62 61 62 68 69 69 76 84 101 108 122 134 144 156 MGA-725M4 Typical Scattering Parameters and Noise Parameters TC = 25C, Vd = 3.0V, Id = 10 mA, ZO = 50 (test circuit of Figure 2) Freq (GHz) S11 Mag. S11 Ang. S21 Mag. S21 Ang. S12 Mag. S12 Ang. S22 Mag. S22 Ang. S21 (dB) RLin (dB) RLout (dB) Gmax (dB) Isolation (dB) 0.10 0.50 0.80 0.90 1.00 1.10 1.20 1.30 1.40 1.50 1.60 1.70 1.80 1.90 2.00 2.10 2.20 2.30 2.40 2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00 0.79 0.68 0.65 0.66 0.64 0.64 0.63 0.63 0.62 0.62 0.62 0.61 0.61 0.61 0.60 0.60 0.60 0.60 0.59 0.59 0.59 0.58 0.57 0.57 0.57 0.56 0.55 0.55 0.54 0.50 0.51 -9 -26 -39 -43 -46 -50 -54 -58 -61 -64 -68 -71 -74 -77 -81 -84 -87 -89 -92 -95 -108 -119 -130 -140 -149 -157 -166 -172 -179 170 164 5.57 5.68 5.47 5.40 5.33 5.25 5.18 5.10 5.03 4.95 4.88 4.81 4.73 4.65 4.58 4.51 4.45 4.36 4.29 4.23 3.91 3.62 3.36 3.13 2.93 2.76 2.58 2.30 2.25 2.19 2.09 174 163 154 152 149 147 144 142 139 137 134 132 130 128 125 123 121 119 117 115 105 96 88 80 73 66 57 48 45 39 33 0.05 0.05 0.06 0.06 0.06 0.06 0.06 0.06 0.07 0.07 0.07 0.07 0.07 0.07 0.07 0.08 0.08 0.08 0.08 0.08 0.09 0.09 0.10 0.10 0.11 0.11 0.11 0.11 0.12 0.13 0.13 19 13 16 18 19 20 21 21 22 23 23 23 24 24 24 24 24 24 24 24 23 23 22 21 20 20 17 17 17 16 15 0.48 0.40 0.39 0.39 0.39 0.39 0.38 0.38 0.38 0.38 0.38 0.37 0.37 0.37 0.37 0.37 0.36 0.36 0.36 0.36 0.35 0.34 0.34 0.33 0.33 0.32 0.32 0.32 0.31 0.31 0.31 -9 -15 -21 -24 -26 -28 -31 -33 -35 -37 -39 -42 -44 -46 -48 -50 -51 -54 -55 -57 -66 -73 -81 -88 -94 -100 -113 -122 -133 -137 -139 14.9 15.1 14.8 14.6 14.5 14.4 14.3 14.2 14.0 13.9 13.8 13.6 13.5 13.4 13.2 13.1 13.0 12.8 12.7 12.5 11.8 11.2 10.5 9.9 9.3 8.8 8.2 7.2 7.0 6.8 6.4 -2.0 -3.4 -3.7 -3.7 -3.9 -3.9 -4.1 -4.1 -4.2 -4.2 -4.2 -4.3 -4.3 -4.3 -4.4 -4.4 -4.5 -4.5 -4.5 -4.5 -4.6 -4.7 -4.8 -4.9 -5.0 -5.1 -5.1 -5.3 -5.4 -6.0 -5.8 -6.4 -8.1 -8.2 -8.2 -8.3 -8.3 -8.3 -8.4 -8.4 -8.4 -8.5 -8.5 -8.6 -8.6 -8.7 -8.7 -8.8 -8.8 -8.8 -8.9 -9.1 -9.3 -9.5 -9.6 -9.8 -9.9 -9.9 -9.9 -10.1 -10.1 -10.1 20.7 18.2 17.9 18.0 17.8 17.8 17.8 17.9 17.9 18.2 18.6 18.4 18.2 18.0 17.9 17.7 17.6 17.5 17.3 17.2 16.5 15.9 15.4 14.9 14.4 14.0 12.5 10.5 10.3 9.6 9.3 -26.6 -25.4 -24.9 -24.7 -24.6 -24.4 -24.2 -24.0 -23.7 -23.5 -23.3 -23.1 -23.0 -22.7 -22.6 -22.4 -22.3 -22.2 -21.9 -21.8 -21.2 -20.6 -20.3 -19.9 -19.5 -19.2 -18.9 -19.1 -18.4 -17.9 -17.5 Freq (GHz) NFmin (dB) GAMMA OPT Mag Ang Rn Ga (dB) 0.8 0.9 1.0 1.5 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 1.20 1.20 1.24 1.28 1.30 1.31 1.34 1.36 1.38 1.40 1.40 1.40 1.42 1.47 1.50 1.54 1.61 1.64 1.72 0.35 0.35 0.34 0.29 0.26 0.24 0.20 0.19 0.19 0.19 0.18 0.18 0.19 0.20 0.22 0.23 0.23 0.25 0.29 14.5 11.9 11.5 10.5 10.2 10.1 9.5 9.1 9.0 9.0 8.7 8.6 8.1 7.7 7.3 7.2 6.6 6.1 5.7 17.5 16.6 16.5 15.9 15.4 15.3 14.6 14.4 14.2 14.2 13.9 13.9 13.4 12.6 12.1 11.4 10.9 10.4 9.8 7 36 39 48 60 64 68 66 68 74 76 75 83 91 109 117 130 144 153 167 MGA-725M4 Typical Scattering Parameters and Noise Parameters TC = 25C, Vd = 3.0 V, Id = 20 mA, ZO = 50 (test circuit of Figure 2) Freq (GHz) S11 Mag. S11 Ang. S21 Mag. S21 Ang. S12 Mag. S12 Ang. S22 Mag. S22 Ang. S21 (dB) RLin (dB) RLout (dB) Gmax (dB) Isolation (dB) 0.1 0.5 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0 0.75 0.62 0.60 0.60 0.59 0.58 0.58 0.57 0.57 0.57 0.57 0.56 0.56 0.56 0.56 0.55 0.55 0.55 0.55 0.55 0.54 0.54 0.53 0.53 0.52 0.52 0.51 0.50 0.49 0.46 0.47 -11 -28 -42 -46 -50 -54 -58 -62 -65 -69 -72 -76 -79 -82 -86 -89 -92 -95 -98 -100 -113 -125 -135 -145 -153 -162 -169 -176 178 166 161 6.78 6.81 6.53 6.44 6.34 6.24 6.14 6.05 5.95 5.85 5.75 5.66 5.56 5.46 5.36 5.27 5.19 5.08 4.99 4.91 4.51 4.15 3.84 3.56 3.33 3.12 2.91 2.58 2.54 2.47 2.35 174 162 153 151 148 145 143 140 138 135 133 130 128 126 124 122 119 117 115 113 104 95 87 79 72 65 57 49 45 39 33 0.04 0.05 0.05 0.05 0.05 0.05 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.07 0.07 0.07 0.07 0.07 0.07 0.08 0.08 0.08 0.09 0.09 0.10 0.10 0.10 0.11 0.12 0.12 12 12 16 17 18 19 20 21 21 22 23 23 23 23 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 23 0.39 0.30 0.30 0.30 0.30 0.30 0.29 0.29 0.29 0.29 0.29 0.29 0.28 0.28 0.28 0.28 0.28 0.28 0.28 0.27 0.27 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.27 0.27 -11 -16 -23 -26 -28 -31 -33 -36 -38 -40 -42 -45 -47 -49 -51 -53 -55 -57 -58 -60 -68 -76 -83 -89 -95 -100 -114 -124 -135 -134 -138 16.6 16.7 16.3 16.2 16.0 15.9 15.8 15.6 15.5 15.3 15.2 15.0 14.9 14.7 14.6 14.4 14.3 14.1 14.0 13.8 13.1 12.4 11.7 11.0 10.4 9.9 9.3 8.2 8.1 7.9 7.4 -2.5 -4.1 -4.4 -4.4 -4.6 -4.7 -4.8 -4.8 -4.9 -4.9 -4.9 -5.0 -5.0 -5.0 -5.1 -5.1 -5.1 -5.2 -5.2 -5.2 -5.3 -5.4 -5.5 -5.6 -5.6 -5.8 -5.8 -6.0 -6.2 -6.8 -6.6 -8.1 -10.4 -10.5 -10.5 -10.6 -10.6 -10.6 -10.7 -10.7 -10.8 -10.8 -10.9 -10.9 -11.0 -11.0 -11.1 -11.2 -11.2 -11.2 -11.2 -11.4 -11.6 -11.6 -11.7 -11.8 -11.8 -11.6 -11.7 -11.6 -11.4 -11.3 20.8 19.1 18.7 18.8 18.6 18.5 18.4 18.4 18.3 18.2 18.2 18.1 18.0 18.0 17.9 17.8 17.7 17.5 17.4 17.3 16.6 15.7 14.9 14.1 13.4 12.7 12.0 10.6 10.4 9.9 9.6 -27.1 -26.2 -25.8 -25.7 -25.5 -25.4 -25.0 -24.9 -24.7 -24.6 -24.3 -24.2 -24.0 -23.9 -23.6 -23.5 -23.3 -23.2 -23.1 -23.0 -22.4 -21.9 -21.5 -21.1 -20.7 -20.4 -19.9 -19.6 -19.4 -18.8 -18.3 Freq (GHz) NFmin (dB) GAMMA OPT Mag Ang Rn Ga (dB) 0.8 0.9 1.0 1.5 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 1.16 1.18 1.19 1.19 1.24 1.26 1.28 1.31 1.31 1.31 1.32 1.33 1.32 1.36 1.40 1.43 1.51 1.55 1.62 0.34 0.33 0.32 0.28 0.23 0.22 0.18 0.17 0.15 0.16 0.16 0.16 0.18 0.18 0.20 0.22 0.23 0.25 0.29 12.1 12.0 11.5 10.7 10.0 9.6 9.8 9.3 9.2 9.1 8.9 8.7 8.3 8.1 7.9 7.9 7.7 7.6 7.7 18.0 17.6 17.6 16.6 16.0 15.8 15.7 15.4 15.2 15.1 14.9 14.8 14.2 13.5 12.8 12.2 11.6 11.1 10.6 8 40 46 50 60 69 73 72 75 81 83 81 89 97 116 123 136 150 158 172 MGA-725M4 Typical Scattering Parameters and Noise Parameters TC = 25C, Vd = 3.0 V, Id = 40 mA, ZO = 50 (test circuit of Figure 2) Freq (GHz) S11 Mag. S11 Ang. S21 Mag. S21 Ang. S12 Mag. S12 Ang. S22 Mag. S22 Ang. S21 (dB) RLin (dB) RLout (dB) Gmax (dB) Isolation (dB) 0.1 0.5 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0 0.75 0.62 0.60 0.60 0.59 0.58 0.58 0.57 0.57 0.57 0.57 0.56 0.56 0.56 0.56 0.55 0.55 0.55 0.55 0.55 0.54 0.54 0.53 0.53 0.52 0.52 0.51 0.50 0.49 0.46 0.47 -11 -29 -43 -47 -51 -55 -60 -63 -67 -71 -74 -78 -81 -85 -88 -91 -94 -97 -100 -103 -115 -127 -137 -147 -155 -164 -172 -176 177 165 160 7.39 7.38 7.06 6.95 6.84 6.73 6.62 6.51 6.40 6.29 6.18 6.07 5.96 5.85 5.74 5.64 5.54 5.43 5.34 5.24 4.79 4.40 4.06 3.77 3.52 3.30 3.06 2.73 2.69 2.61 2.49 173 162 153 150 147 145 142 140 137 135 132 130 128 125 123 121 119 117 115 113 103 95 87 79 72 65 57 49 46 40 34 0.04 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.07 0.07 0.08 0.08 0.08 0.09 0.09 0.09 0.10 0.11 0.12 18 11 15 16 17 18 19 20 21 22 22 23 23 24 24 24 24 25 25 25 26 26 26 27 27 28 27 25 28 28 27 0.35 0.26 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.24 0.24 0.24 0.24 0.24 0.24 0.23 0.24 0.24 0.23 0.23 0.23 0.23 0.23 0.23 0.23 0.23 0.23 0.23 0.24 0.25 -12 -16 -23 -26 -28 -31 -33 -36 -38 -40 -42 -45 -47 -49 -51 -53 -54 -56 -58 -60 -67 -74 -81 -86 -91 -96 -112 -125 -132 -130 -134 17.4 17.4 17.0 16.8 16.7 16.6 16.4 16.3 16.1 16.0 15.8 15.7 15.5 15.3 15.2 15.0 14.9 14.7 14.5 14.4 13.6 12.9 12.2 11.5 10.9 10.4 9.7 8.7 8.6 8.3 7.9 -2.5 -4.1 -4.4 -4.4 -4.6 -4.7 -4.8 -4.8 -4.9 -4.9 -4.9 -5.0 -5.0 -5.0 -5.1 -5.1 -5.1 -5.2 -5.2 -5.2 -5.3 -5.4 -5.5 -5.6 -5.6 -5.8 -5.8 -6.0 -6.2 -6.8 -6.6 -9.2 -11.8 -12.0 -12.0 -12.0 -12.1 -12.1 -12.1 -12.2 -12.2 -12.3 -12.3 -12.4 -12.4 -12.4 -12.5 -12.6 -12.6 -12.6 -12.7 -12.8 -12.9 -12.9 -13.0 -12.9 -12.9 -12.7 -12.7 -12.6 -12.3 -12.1 22.1 19.8 19.4 19.4 19.1 19.0 18.9 18.8 18.7 18.6 18.5 18.4 18.3 18.2 18.1 17.9 17.7 17.6 17.4 17.3 16.6 15.7 14.9 14.2 13.5 12.8 12.2 10.8 10.7 10.2 9.9 -27.7 -26.7 -26.6 -26.4 -26.2 -26.0 -25.8 -25.7 -25.5 -25.4 -25.2 -25.0 -24.9 -24.6 -24.4 -24.3 -24.3 -24.2 -24.0 -23.9 -23.2 -22.7 -22.4 -21.9 -21.5 -21.1 -20.7 -20.8 -19.9 -19.3 -18.7 Freq (GHz) NFmin (dB) GAMMA OPT Mag Ang Rn Ga (dB) 0.8 0.9 1.0 1.5 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 1.23 1.24 1.27 1.28 1.32 1.32 1.37 1.40 1.40 1.40 1.40 1.42 1.43 1.47 1.51 1.56 1.65 1.64 1.77 0.36 0.35 0.35 0.28 0.25 0.24 0.22 0.20 0.21 0.20 0.20 0.20 0.22 0.22 0.24 0.25 0.26 0.29 0.32 14.7 12.4 11.5 10.3 10.1 9.9 9.4 9.2 9.1 9.0 8.7 8.6 8.0 7.5 7.0 6.7 6.1 5.6 5.3 19.0 18.2 18.2 17.3 16.7 16.4 16.2 16.0 15.8 15.7 15.5 15.4 14.7 14.0 13.3 12.7 12.1 11.6 11.1 9 33 42 50 63 68 72 72 74 79 82 81 88 97 115 124 138 151 160 173 MGA-725M4 Typical Scattering Parameters and Noise Parameters TC = 25C, Vd = 3.0 V, Id = 60 mA, ZO = 50 (test circuit of Figure 2) Freq (GHz) S11 Mag. S11 Ang. S21 Mag. S21 Ang. S12 Mag. S12 Ang. S22 Mag. S22 Ang. S21 (dB) RLin (dB) RLout (dB) Gmax (dB) Isolation (dB) 0.1 0.5 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0 0.76 0.64 0.61 0.62 0.60 0.60 0.59 0.59 0.58 0.58 0.58 0.58 0.57 0.57 0.57 0.57 0.57 0.57 0.56 0.56 0.56 0.55 0.54 0.54 0.54 0.53 0.52 0.51 0.50 0.47 0.48 -11 -29 -42 -47 -50 -55 -59 -63 -66 -70 -73 -77 -80 -84 -87 -90 -93 -96 -99 -102 -115 -126 -137 -146 -155 -163 -171 -177 177 165 161 7.09 7.08 6.78 6.69 6.58 6.48 6.38 6.28 6.17 6.07 5.96 5.86 5.76 5.66 5.56 5.46 5.36 5.26 5.17 5.07 4.65 4.27 3.95 3.67 3.42 3.21 2.98 2.66 2.63 2.55 2.43 174 162 153 151 148 145 143 140 137 135 133 130 128 126 123 121 119 117 115 113 103 95 87 79 72 65 57 49 45 39 33 0.04 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.07 0.07 0.07 0.08 0.08 0.08 0.09 0.09 0.10 0.10 0.11 17 10 14 15 17 18 19 19 20 21 21 22 22 23 23 24 24 24 24 24 25 26 26 27 28 29 28 27 30 30 30 0.35 0.26 0.26 0.26 0.26 0.26 0.26 0.26 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.24 0.24 0.24 0.24 0.24 0.24 0.24 0.24 0.24 0.24 0.24 0.25 0.24 0.25 0.26 -11 -15 -21 -24 -26 -28 -31 -33 -35 -37 -39 -41 -43 -45 -47 -48 -50 -52 -53 -55 -62 -69 -75 -80 -85 -90 -106 -118 -125 -130 -127 17.0 17.0 16.6 16.5 16.4 16.2 16.1 16.0 15.8 15.7 15.5 15.4 15.2 15.1 14.9 14.7 14.6 14.4 14.3 14.1 13.3 12.6 11.9 11.3 10.7 10.1 9.5 8.5 8.4 8.1 7.7 -2.4 -3.9 -4.2 -4.2 -4.4 -4.5 -4.6 -4.6 -4.7 -4.7 -4.7 -4.8 -4.8 -4.8 -4.9 -4.9 -5.0 -5.0 -5.0 -5.0 -5.1 -5.2 -5.3 -5.4 -5.4 -5.5 -5.7 -5.8 -6.0 -6.6 -6.4 -9.1 -11.6 -11.7 -11.8 -11.8 -11.8 -11.8 -11.9 -11.9 -11.9 -12.0 -12.0 -12.1 -12.1 -12.1 -12.2 -12.3 -12.3 -12.3 -12.3 -12.5 -12.5 -12.6 -12.6 -12.5 -12.5 -12.4 -12.1 -12.4 -12.0 -11.8 21.7 19.5 19.1 19.0 18.8 18.7 18.6 18.5 18.3 18.2 18.1 18.0 17.9 17.8 17.7 17.5 17.4 17.2 17.1 17.0 16.2 15.4 14.6 13.9 13.3 12.7 11.9 10.7 10.5 10.0 9.8 -28.0 -26.9 -26.7 -26.6 -26.4 -26.4 -26.2 -26.0 -25.8 -25.7 -25.5 -25.4 -25.2 -25.0 -24.9 -24.7 -24.6 -24.4 -24.3 -24.2 -23.7 -23.2 -22.9 -22.4 -22.0 -21.6 -21.2 -21.3 -20.4 -19.7 -19.2 Freq (GHz) NFmin (dB) GAMMA OPT Mag Ang Rn Ga (dB) 0.8 0.9 1.0 1.5 1.8 1.9 2.0 2.1 2.2 2.3 2.4 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 1.47 1.47 1.51 1.55 1.56 1.59 1.62 1.65 1.66 1.67 1.67 1.70 1.70 1.76 1.83 1.90 2.00 2.05 2.19 0.38 0.38 0.38 0.34 0.31 0.30 0.29 0.28 0.28 0.27 0.27 0.27 0.27 0.29 0.31 0.32 0.34 0.36 0.39 19.0 17.8 17.3 16.1 14.9 14.6 14.4 14.3 14.2 14.1 13.9 13.6 12.9 12.7 12.4 12.2 11.8 11.7 11.6 18.8 18.2 18.1 17.4 17.0 16.8 16.2 16.0 15.8 15.7 15.5 15.4 14.7 14.0 13.4 12.7 12.2 11.7 11.2 10 42 48 49 60 64 68 69 71 76 78 79 84 96 113 124 137 150 159 173 MGA-725M4 Typical Scattering Parameters-- Zero Bias TC = 25C, Vd = 0 V, Id = 0 mA, ZO = 50 (test circuit of Figure 2) Freq (GHz) S11 Mag. S11 Ang. S21 Mag. S21 Ang. S12 Mag. S12 Ang. S22 Mag. S22 Ang. S21 (dB) RLin (dB) RLout (dB) Isolation (dB) 0.1 0.5 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6 3.8 4.0 4.4 4.8 5.2 5.6 6.0 0.07 0.31 0.42 0.52 0.58 0.62 0.64 0.66 0.67 0.69 0.69 0.69 0.70 0.71 0.72 0.72 0.72 -116 -136 -143 -154 -163 -170 -176 178 173 168 166 163 159 154 150 145 142 0.04 0.06 0.07 0.09 0.09 0.10 0.11 0.11 0.12 0.12 0.12 0.13 0.13 0.14 0.15 0.16 0.16 10 28 30 28 26 24 24 23 23 23 23 23 22 22 22 20 17 0.04 0.06 0.07 0.09 0.09 0.10 0.11 0.11 0.12 0.12 0.13 0.13 0.13 0.14 0.15 0.16 0.16 10 29 30 28 26 25 24 23 23 23 23 23 23 22 22 21 17 0.83 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.85 0.84 0.84 0.84 0.84 0.83 0.83 179 176 174 171 168 165 162 159 156 153 151 149 146 143 139 135 135 -27.3 -24.7 -22.9 -21.4 -20.5 -20.0 -19.5 -19.2 -18.7 -18.3 -18.1 -17.9 -17.5 -17.0 -16.5 -16.0 -15.7 -23.2 -10.2 -7.5 -5.6 -4.7 -4.2 -3.8 -3.6 -3.4 -3.3 -3.2 -3.2 -3.1 -3.0 -2.9 -2.8 -2.9 -1.6 -1.4 -1.4 -1.4 -1.4 -1.4 -1.4 -1.4 -1.4 -1.5 -1.5 -1.5 -1.5 -1.5 -1.5 -1.6 -1.6 -27.3 -24.7 -22.9 -21.4 -20.5 -19.9 -19.5 -19.1 -18.7 -18.3 -18.1 -17.9 -17.5 -17.0 -16.5 -16.0 -15.7 Ordering Information Part Number Devices Per Container Container MGA-725M4-TR1 3000 7" Reel MGA-725M4-TR2 10000 13"Reel MGA-725M4-BLK 100 antistatic bag MiniPak Package Outline Drawing Solder Pad Dimensions 1.44 (0.058) 1.40 (0.056) GROUND OUTPUT 1.12 (0.045) 1.08 (0.043) 0.82 (0.033) 0.78 (0.031) 1.20 (0.048) 1.16 (0.046) INPUT GROUND 0.32 (0.013) 0.28 (0.011) 0.00 -0.07 (-0.003) -0.03 (-0.001) 0.00 -0.07 (-0.003) -0.03 (-0.001) 0.42 (0.017) 0.38 (0.015) 0.92 (0.037) 0.88 (0.035) 1.32 (0.053) 1.28 (0.051) 0.70 (0.030) MAX Note: Pad orientation is shown as viewed from top of package. 11 Package 4T -- MiniPak 1412 Device Orientation REEL TOP VIEW END VIEW 4 mm CARRIER TAPE AA AA AA AA 8 mm USER FEED DIRECTION COVER TAPE Note: "AA" represents package marking code. Package marking is right side up with carrier tape perforations at top. Conforms to Electronic Industries RS-481, "Taping of Surface Mounted Components for Automated Placement." Standard quantity is 3,000 devices per reel. Tape Dimensions For Outline 4T P P2 D P0 E F W C D1 t1 (CARRIER TAPE THICKNESS) Tt (COVER TAPE THICKNESS) K0 5 MAX. A0 DESCRIPTION 12 5 MAX. B0 SYMBOL SIZE (mm) SIZE (INCHES) CAVITY LENGTH WIDTH DEPTH PITCH BOTTOM HOLE DIAMETER A0 B0 K0 P D1 1.40 0.05 1.63 0.05 0.80 0.05 4.00 0.10 0.80 0.05 0.055 0.002 0.064 0.002 0.031 0.002 0.157 0.004 0.031 0.002 PERFORATION DIAMETER PITCH POSITION D P0 E 1.50 0.10 4.00 0.10 1.75 0.10 0.060 0.004 0.157 0.004 0.069 0.004 CARRIER TAPE WIDTH THICKNESS W t1 8.00 + 0.30 - 0.10 0.254 0.02 0.315 + 0.012 - 0.004 0.010 0.001 COVER TAPE WIDTH TAPE THICKNESS C Tt 5.40 0.10 0.062 0.001 0.213 0.004 0.002 0.00004 DISTANCE CAVITY TO PERFORATION (WIDTH DIRECTION) F 3.50 0.05 0.138 0.002 CAVITY TO PERFORATION (LENGTH DIRECTION) P2 2.00 0.05 0.079 0.002 Application Information: Designing with the MGA-725M4 RFIC Amplifier/Bypass Switch Description The MGA-725M4 is a single stage GaAs RFIC amplifier with an integrated bypass switch. A functional diagram of the MGA-725M4 is shown in Figure 1. RF INPUT BYPASS MODE RF OUTPUT AMPLIFIER Figure 1. MGA-725M4 Functional Diagram. The MGA-725M4 is designed for receivers and transmitters operating from 100 MHz to 6 GHz with an emphasis on 800 MHz and 1.9 GHz CDMA applications. The MGA-725M4 combines low noise performance with high linearity to make it especially advantageous for use in receiver front-ends. The purpose of the switch feature is to prevent distortion of high signal levels in receiver applications by bypassing the amplifier altogether. The bypass switch can be thought of as a 1-bit digital AGC circuit that not only prevents distortion by bypassing the MGA-725M4 amplifier, but also reduces front-end system gain by approximately 16 dB to avoid overdriving subsequent stages in the receiver such as the mixer. An additional feature of the MGA-725M4 is the ability to externally set device current to balance output power capability and high linearity with low DC power consumption. The adjustable current feature of the MGA-725M4 allows it to deliver output power levels in excess of +15 dBm (P1dB), thus extending its use to other system application such as transmitter driver stages. 13 The MGA-725M4 is designed to operate from a +3-volt power supply and is contained in miniature Minipak 1412 package to minimize printed circuit board space. LNA Application For low noise amplifier applications, the MGA-725M4 is typically biased in the 10-20 mA range. Minimum NF occurs at 20 mA as noted in the performance curve of NFmin vs Id. Biasing at currents significantly less than 10 mA is not recommended since the characteristics of the device begin to change very rapidly at lower currents. The MGA-725M4 is matched internally for low NF. Over a current range of 10-30 mA, the magnitude of Gopt at 1900 MHz is typically less than 0.25 and additional impedance matching would only net about 0.1 dB improvement in noise figure. Without external matching, the input return loss for the MGA-725M4 is approximately 5 dB at 1900 MHz. If desired, a small amount of NF can be traded off for a significant improvement in input match. For example, the addition of a series inductance of 2.7 to 3.9 nH at the input of the MGA-725M4 will improve the input return loss to grater than 10 dB with a sacrifice in NF of only 0.1 dB. The output of the MGA-725M4 is internally matched to provide an output SWR of approximately 2:1 at 1900 MHz. Input and output matches both improve at higher frequencies. Driver Amplifier Applications The flexibility of the adjustable current feature makes the MGA-725M4 suitable for use in transmitter driver stages. Biasing the amplifier at 40-50 mA enables it to deliver an output power at 1 dB gain compression of up to +16 dBm. Power efficiency in the unsaturated driver mode is on the order of 30%. If operated as a saturated amplifier, both output power and efficiency will increase. Since the MGA-725M4 is internally matched for low noise figure, it may be desirable to add external impedance matching at the input to improve the power match for driver applications. Since the reactive part of the input of the device impedance is capacitive, a series inductor at the input is often all that is needed to provide a suitable match for many applications. For 1900 MHz circuits, a series inductance of 3.9 nH will match the input to return loss of approximately 13 dB. As in the case of low noise bias levels, the output of the MGA-725M4 is already well matched to 50 and no additional matching is needed for most applications. When used for driver stage applications, the bypass switch feature of the MGA-725M4 can be used to shut down the amplifier to conserve supply current during non-transmit period. Supply current in the bypass stage is nominally 2 mA. Biasing Biasing the MGA-725M4 is similar to biasing a discrete GaAs FET. Passive biasing of the MGA-725M4 may be accomplished by either of two conventional methods, either by biasing the gate or by using a source resistor. Gate Bias Using this method, Pins 1 and 3 of the amplifier are DC grounded and a negative bias voltage is applied to Pin 2 as shown in figure 2. This method has the advantage of not only DC, but also RF grounding both of the ground pins of the MGA-725M4. Direct RF grounding The gate bias method would not normally be used unless a negative supply voltage was readily available. For reference, this is the method used in the characterization test circuits shown in Figures 1 and 2 of the MGA-725M4 data sheet. OUTPUT & Vd INPUT Figure 2. Gate Bias Method. DC access to the input terminal for applying the gate bias voltage can be made through either a RF or high impedance transmission line as indicated in Figure 2. The device current, Id, is determined by the voltage at Vref (Pin 2) with respect to ground. A plot of typical Id vs Vref is shown in Figure 3. Maximum device current (approximately 65 mA) occurs at Vref = 0. Source Resistor Bias The source resistor method is the simplest way of biasing the MGA-725M4 using a single, positive supply voltage. This method, shown in Figure 4, places the RF input at DC ground and requires both of the device grounds to be RF bypassed. Device current, Id, is determined by the value of the source resistance, Rbias, between either Pin 1 and Pin 3 of the MGA-725M4 and DC ground. Pin 1 and Pin 3 are connected internally in the RFIC. Maximum device current (approximately 65 mA) occurs for Rbias= 0. INPUT 2 4 1 The device current may also be estimated from the following equation: Vref = 0.11 Id - 0.96 Id (mA) 40 30 20 10 -0.5 -0.4 Vref (V) Figure 3. Device Current vs. Vref . 14 -0.3 3 Figure 4. Source Resistor Bias. 50 -0.6 OUTPUT & Vd Rbias where Id is in mA and Vref is in volts. -0.7 50 40 30 20 10 Vref 0 -0.8 60 Id (mA) of device's ground pins results in slightly improved performance while decreasing potential instabilities, especially at higher frequencies. The disadvantage is that a negative supply voltage is required. -0.2 A simple method recommended for DC grounding the input terminal is to merely add a resistor from Pin 2 to ground, as shown in Figure 4. The value of the shunt R can be comparatively high since the only voltage drop across it is due to minute leakage currents that in the mA range. A value of 1k would adequately DC ground the input while loading the RF signal by only 0.2 dB loss. A plot of typical Id vs Rbias is shown in Figure 5. 0 0 20 40 60 80 100 120 140 Rbias () Figure 5. Device Current vs. Rbias. The approximate value of the external resistor, Rbias, may also be calculated from: Rbias = 964 (1 - 0.112 Id) Id where Rbias is in ohms and Id is the desired device current in mA. The source resistor technique is the preferred and most common method of biasing the MGA-725M4. Adaptive Biasing For applications in which input power levels vary over a wide range, it may be useful to dynamically adapt the bias of the MGA-725M4 to match the signal level. This involves sensing the signal level at some point in the system and automatically adjusting the bias current of the amplifier accordingly. The advantage of adaptive biasing is conservation of supply current (longer battery life) by using only the amount of current necessary to handle the input signal without distortion. Adaptive biasing of the MGA-725M4 can be accomplished by either analog or digital means. For the analog control case, an active current source (discrete device or IC) is used in lieu of the source bias resistor. For simple digital control, electronic switches can be used to control the value of the source resistor in discrete increments. Both methods of adaptive biasing are depicted in Figure 6. Applying the Device Voltage Common to all methods of biasing, voltage Vd is applied to the MGA-725M4 through the RF Output connection (Pin 4). A RF choke is used to isolate the RF signal from the DC supply. The bias line is capacitively bypassed to keep RF from the DC supply lines and prevent resonant dips or peaks in the response of the amplifier. Where practical, it may be cost effective to use a length of high impedance transmission line (Preferably /4) in place of the RFC. When using the gate bias method, the overall device voltage is equal to the sum of Vref at Pin 2 and voltage Vd at Pin 4. As an example, to bias the device at the typical operating voltage of 3 volts, Vd would be set to 2.5 volts for a Vref of -0.5 volts. Figure 7 shows a DC schematic of a gate bias circuit. Just as for the gate bias method, the overall device voltage for source resistor biasing is equal to Vref + Vd. Since Vref is zero when using a source resistor, Vd is the same as the device operating voltage, typically 3 volts. A source resistor bias circuit is shown in Figure 8. Input 2 4 1 Output & Vd Vd = +2.5 V RFC RF Output RF Input Vref = -0.5 V Figure 7. DC Schematic for Gate Bias. Vd = +2.5 V RFC RF Output RF Input Rbias Figure 8. DC Schematic of Source Resistor Biasing. A DC blocking capacitor at the output of the RFIC isolates the supply voltage from succeeding circuits. If the source resistor method of biasing is used, the RF input terminal of the MGA-725M4 is at DC ground potential and a blocking capacitor is not required unless the input is connected directly to a preceding stage that has a DC voltage present. Input 2 3 2 1 3 Analog Control Analog Control Vref Vref (a) Analog Figure 6. Adaptive Bias Control. 15 Output & Vd (b) Digital Biasing for Higher Linearity or Output Power While the MGA-725M4 is designed primarily for use up to 50 mA in 3 volt applications, the output power can be increased by using higher currents and/or higher supply voltages. If higher bias levels are used, appropriate caution should be observed for both the thermal limits and the Absolute Maximum Ratings. As a guideline for operation at higher bias levels, the Maximum Operating conditions shown in the data sheet table of Absolute Maximum Ratings should be followed. This set of conditions is the maximum combination of bias voltage, bias current, and device temperature that is recommended for reliable operation. Note: In contrast to Absolute Maximum Ratings, in which exceeding may one parameter may result in damage to the device, all of the Maximum Operating conditions may reliably be applied to the MGA-725M4 simultaneously. Controlling the Switch The state of the MGA-725M4 (amplifier or bypass mode) is controlled by the device current. For device currents greater than 5 mA, the MGA-725M4 functions as an amplifier. If the device current is set to zero, the MGA-725M4 is switched into bypass mode in which the amplifier is turned off and the signal is routed around the amplifier with a loss of approximately 2.5 dB. The bypass state is normally engaged in the presence of high input levels to prevent distortion of the signal that might occur in the amplifier. In the bypass state the input TOI is very high, typically +39 dBm at 1900 MHz. The simplest method of placing the MGA-725M4 into the bypass mode is to open-circuit the ground terminals at Pins 1 and 3. With the ground connection open, the internal control circuit of the MGA-725M4 auto-switches from the amplifier mode into a bypass state and the device current drops to near zero. Nominal current in the bypass state is 2 A with a maximum of 15 A. Input 2 4 1 Output & Vd 3 Rbias Bypass Switch Enable Figure 9. MGA-725M4 Amplifier/Bypass State Switching. An electronic switch can be used to control states as shown in Figure 9. The control switch could be implemented with either a discrete transistor or simple IC. The speed at which the MGA-725M4 switches between states is extremely fast and will normally be limited by the time constants of external circuit components, such as the bias circuit and the bypass and blocking capacitors. The input and output of the MGA-725M4 while in the bypassed state are internally matched to 50. The input return loss can be further improved at 1900 MHz by adding a 2.9 to 3.9 nH series inductor added to the input. This is the same approximate value of inductor that is used to improve input match when the MGA-725M4 is in the amplifier state. 16 Thermal Considerations Good thermal design is always an important consideration in the reliable use of any device, since the Mean Time To Failure (MTTF) of semiconductors is inversely proportional to the operating temperature. PCB Layout and Grounding When laying out a printed circuit board for the MGA-725M4, several points should be considered. Of primary concern is the RF bypassing of the ground terminals when the device is biased using the source resistor method. The MGA-725M4 is a comparatively low power dissipation device. When biased at 3 volts and 20 mA for LNA application, the power dissipation is 3.0 volts x 20 mA or 60 mW. The temperature increment from the RFIC channel to its case is then 0.060 watt x 200C/Watt, or only 12C. Subtracting the channel to case temperature rise from the suggested maximum junction temperature of 150C, the resulting maximum allowable case temperature is 138C. Package Footprint A suggested PCB pad print for the miniature, Minipak 1412 package used by the MGA-725M4 is shown in Figure 10. The worst case thermal situation occurs when the MGA-725M4 is operated at its Maximum Operating Conditions in an effort to maximize output power or to achieve minimum distortion. A similar calculation for the Maximum Operating bias of 4.2 volts and 60 mA yields a maximum allowable case temperature of 100C. This calculation further assumes the worst case of no RF power being extracted from the device. When operated in a saturated mode, both power added efficiency and the maximum allowable case temperature will increase. Note "Case" temperature for surface mount packages such as the SOT-343 refers to the interface between the package pins and the mounting surface, i.e., the temperature at the PCB mounting pad. The primary heat path from the RFIC chip to the system heat sink is by means of conduction through the package leads and ground vias to the ground plane of the PCB. 0.4 0.016 0.3 0.012 0.5 0.020 1.1 0.043 0.3 0.012 0.4 0.016 0.5 0.020 Figure 10. PCB Pad Print for Minipak 1412 Package (mm [inches]). This pad print provides allowance for package placement by automated assembly equipment without adding excessive parasitics that could impair the high frequency performance of the MGA-725M4. The layout is shown with a footprint of the MGA-725M4 superimposed on the PCB pads for reference. RF Bypass For layouts using the source resistor method of biasing, both of the ground terminals of the MGA-725M4 must be well by-passed to maintain device stability. Beginning with the package pad print in Figure 10, a RF layout similar to the one shown in Figure 11 is a good starting point for using the MGA-725M4 with capacitor-bypassed ground terminals. It is a best practice to use multiple vias to minimize overall ground path inductance. A complete evaluation amplifier optimized for use at 1900 MHz is shown with all related components and SMA connectors in Figure 13. A schematic diagram of the evaluation circuit is shown in Figure 14 with component values in Table 1. that are greater than this are not recommended due to excessive inductance in the vias. Application Example An example evaluation PCB layout for the MGA-725M4 is shown in Figure 12. This evaluation circuit is designed for operation from a +3-volts supply and includes provision for a 2-bit DIP switch to set the state of the MGA-725M4. For evaluation purposes, the 2-bit switch is used to set the device to either of four states: (1) bypass mode-switch bypasses the amplifier, (2) low noise amplifier mode-low bias current, (3) and (4) driver amplifier modes-high bias currents. Table 1. Component Values for 1900 MHz Amplifier. R1 R2 R3 R4 L1 RFC SW1, SW2 SC Figure 12. PCB Layout for Evaluation Circuit. Vd AGILENT MGA-71,72 9/00 C C0 RFC C4 SC C3 CSP IN C1 R1 C2 C6 L1 C5 C C Out R3 R2 C0 Vin PCB material FR-4 or G-10 type dielectric materials are typical choices for most low cost wireless applications using single or multi-layer printed circuit boards. The thickness of single-layer boards usually range from 0.020 to 0.031 inches. Circuit boards should be constructed so that distance to ground for RF signals are less than 0.031 inches. Using PCB layer stacks SW C0 Figure 13. Complete Amplifier with Component Reference Designators. 17 C C0 C1 C2 C3 C4 C5 C6 =100 pF =1000 pF =100 pF =47 pF =30 pF =22 pF =22 pF =30 pF The on-board resistors R3 and R4 form the equivalent source bias resistor Rbias as indicated in the schematic diagram in Figure 14. In this example, resistor values of R3 = 10 and R4 =24 were chosen to set the nominal device current for the four states: (1) bypass mode, 0 mA, (2) LNA mode, 20 mA, (3) driver, 35 mA, and (4) driver, 40 mA. Figure 11. Layout for RF Bypass. If the source resistor biasing method is used, a ground pad located near either Pin 1 or Pin 3 may be used to connect the current-setting resistor (Rbias) directly to DC ground. If the Rbias resistor is not located immediately adjacent to the MGA-725M4 (as may be the case of dynamic control of the device's linearity), then a small series resistor (e.g. 10) located near the ground terminal will help de-Q the connection from the MGA-725M4 to an external current-setting circuit. =5.1 k =5.1 k =10 =24 =3.9 nH =22 nH DIP switch Short Vcon Two capacitors are used at each of the PCB pads for both Pins 1 and 3. The value of the bypass capacitors is a balance between providing a small reactance for good RF grounding, yet not being so large that the capacitor's parasitics introduce undesirable resonances or loss. bias circuits to ensure stable operation. In multistage circuits, feedback through bias lines can also lead to oscillation. Vd C0 C RFC C2 C3 RF Input RF Output C4 C1 L1 C C5 C6 R1 C R2 SW1 R3 SW2 R4 C0 C0 Rbias Components of insufficient quality for the frequency range of the amplifier can sometimes lead to instability. Also, component values that are chosen to be much higher in value than is appropriate for the application can present a problem. In both of these cases, the components may have reactive parasitics that make their impedances very different than expected. Chip capacitors may have excessive inductance or chip inductors can exhibit resonances at unexpected frequencies. Vcon Figure 14. Schematic Diagram of 1900 MHz Evaluation Amplifier. Other currents can be set by positioning the DIP switch to the bypass state and adding an external bias resistor to Vcon. Unless an external resistor is used to set the current, the Vcon terminal is left open. DC blocking capacitors are provided for the both the input and output. The 2-pin, 0.100" centerline single row headers attached to the Vd and Vcon connections on the PCB provide a convenient means of making connections to the board using either a mating connector or clip leads. A Note on Performance Actual performance of the MGA-725M4 as measured in an evaluation circuit may not exactly match the datasheet specifications. The circuit board material, passive components, RF bypasses and connectors all introduce losses and parasitics that degrade device performance. 18 For the evaluation circuit above, fabricated on 0.031-inch thick GETEK G200D (er=4.2) dielectric material, circuit losses of about 0.3 dB would be expected at both the input and output sides of the RFIC at 1900 MHz. Measured noise figure (3 volts, 20 mA bias) would then be approximately 1.8 dB and gain 13.8 dB. Hints and Troubleshooting Preventing Oscillation Stability of the MGA-725M4 is dependent on having very good RF grounding. Inadequate device grounding or poor PCB layout techniques could cause the device to be potentially unstable. Even though a design may be unconditionally stable (K>1 and B1>0) over its full frequency range, other possibilities exist that may cause an amplifier circuit to oscillate. One condition to check for is feedback in the bias circuit. It is important to capacitively bypass the connections to active A Note on Supply Line Bypassing Multiple bypass capacitors are normally used throughout the power distribution within a wireless system. Consideration should be given to potential resonances formed by the combination of these capacitors and the inductance of the DC distribution lines. The addition of a small value resistor in the bias supply line between bypass capacitors will often de-Q the bias circuit and eliminate resonance effects. Statistical Parameters Several categories of parameters appear within the electrical specification portion of the MGA-725M4 data sheet. Parameters may be described with values that are either "minimum or maximum", "typical" or "standard deviation". The values for parameters are based on comprehensive product characterization data, in which automated measurements are made on a statistically significant number of parts taken from nonconsecutive process lots of semiconductor wafers. The data derived from product characterization tends to be normally distributed, e.g., fits the standard bell curve. Parameters considered to be the most important to system performance are bounded by minimum or maximum values. For the MGA-725M4, these parameters are: Vc test, NFtest, Ga test, IIP3test, and ILtest. Each of the guaranteed parameters is 100% tested as part of normal manufacturing and test process. Values for most of the parameters in the table of Electrical Specifications that are described by typical data are mathematical mean (), of the normal distribution taken from the characterization data. For parameters where measurements of mathematical averaging may not be practical, such as S-parameters or Noise Parameters and the performance curve, the data represents a nominal part taken from the center of the characterization distribution. Typical values are intended to be used as a basis for electrical design. To assist designers in optimizing not only the immediate amplifier circuit using the MGA-725M4, but to also evaluate and optimize trade-offs that affect a complete wireless system, the standard deviation () is provided for many of the Electrical Specification parameters (at 25C). The standard deviation is a measure of variability about the mean. It will be recalled that a normal distribution is completely described by the mean and standard deviation. Standard statistics tables or calculations provide the probability of a parameter falling between any two values, usually symmetrically located about the mean. 19 Referring to Figure 15 for example, the probability of a parameter being between 1 is 68.3%; between 2 is 95.4%; and between 3 is 99.7%. 68% 95% 99% -3 -2 -1 Mean () +1 (typical) +2 +3 Parameter Value Figure 15. Normal Distribution Curve. Phase Reference Planes The positions of the reference planes used to specify S-parameters and Noise Parameters for the MGA-725M4 are shown in Figure 16. As seen in the illustration, the reference planes are located at centre of package solder pads. S and Noise Parameter data was taken with the package mounted to 50 ohm lines on 10 mil alumina substrates, and the ground pads were connected directly to the substrate ground plane through a solid metal rib. Designers should include the parasitics of the grounding system used in their application. Reference Planes Bottom View Figure 16. Phase Reference Planes. SMT Assembly The package can be soldered using either lead-bearing or leadfree alloys. Reliable assembly of surface mount components is a complex process that involves many material, process, and equipment factors, including: method of heating (e.g. IR or vapor phase reflow, wave soldering, etc) circuit board material, conductor thickness and pattern, type of solder alloy, and the thermal conductivity and thermal mass of components. Components with a low mass, such as the Minipak 1412 package, will reach solder reflow temperatures faster than those with a greater mass. The MGA-725M4 has been qualified to the time-temperature profile shown in Figure 17. This profile is representative of an IR reflow type of surface mount assembly process. After ramping up from room temperature, the circuit board with components attached to it (held in place with solder paste) passes through one or more preheat zones. The preheat zones increase the temperature of the board and components to prevent thermal shock and begin evaporating solvents from the solder paste. The reflow zone briefly elevates the temperature sufficiently to produce a reflow of the solder. The rates of change of temperature for the ramp-up and cooldown zones are chosen to be low enough to not cause deformation of board or damage to components due to thermal shock. The maximum temperature in the reflow zone (Tmax) should not exceed 235C. Any user-accessible points in wireless equipment (e.g. antenna or battery terminals) provide an opportunity for ESD damage. 250 TMAX TEMPERATURE (C) 200 150 Reflow Zone 100 Preheat Zone Cool Down Zone 50 0 0 60 120 180 240 300 TIME (seconds) Figure 17. Surface Mount Assembly Profile. These parameters are typical for a surface mount assembly process for the MGA-725M4. As a general guideline, the circuit board and components should only be exposed to the minimum temperatures and times necessary to achieve a uniform reflow of solder. Electrostatic Sensitivity RFIC are electrostatic discharge (ESD) sensitive devices. Although the MGA-725M4 is robust in design, permanent damage may occur to these devices if they are subjected to high-energy electrostatic discharges. Electrostatic charges as high as several thousand volts (which readily accumu- www.semiconductor.agilent.com Data subject to change. Copyright (c) 2001 Agilent Technologies, Inc. Obsoletes 5988-1547EN October 1, 2001 5988-4278EN late on the human body and on test equipment) can discharge without detection and may result in failure or degradation in performance and reliability. For circuit applications is which the MGA-725M4 is used as an input or output stage with close coupling to an external antenna, the RFIC should be protected from high voltage spikes due to human contact with the antenna. A best practice, illustrated in Figure 18, is to place a shunt inductor (RFC) at the antenna connection to protect the receiver and transmitter circuits. It is often advantageous to integrate the RFC into a diplexer or T/R switch control circuitry. Electronic devices may be subjected to ESD damage in any of the following areas : * * * * Storage & handling Inspection Assembly & testing In-circuit use The MGA-725M4 is an ESD Class 1 device. Therefore, proper ESD precautions are recommended when handling, inspection, testing, assembling, and using these devices to avoid damage. Figure 18. In-circuit ESD Protection.