DAC121C081, DAC121C085 www.ti.com SNAS395D - DECEMBER 2007 - REVISED MARCH 2013 DAC121C081/ DAC121C085 12-Bit Micro Power Digital-to-Analog Converter with an I2CCompatible Interface Check for Samples: DAC121C081, DAC121C085 FEATURES DESCRIPTION * * * The DAC121C081 is a 12-bit, single channel, voltageoutput digital-to-analog converter (DAC) that operates from a +2.7V to 5.5V supply. The output amplifier allows rail-to-rail output swing and has an 8.5sec settling time. The DAC121C081 uses the supply voltage as the reference to provide the widest dynamic output range and typically consumes 132A while operating at 5.0V. It is available in 6-lead SOT and WSON packages and provides three address options (pin selectable). 1 23 * * * Guaranteed Monotonicity to 12-Bits Low Power Operation: 156 A Max @ 3.3V Extended Power Supply Range (+2.7V to +5.5V) I2C-Compatible 2-Wire Interface Which Supports Standard (100kHz), Fast (400kHz), and High Speed (3.4MHz) Modes Rail-to-Rail Voltage Output Very Small Package APPLICATIONS * * * * * Industrial Process Control Portable Instruments Digital Gain and Offset Adjustment Programmable Voltage & Current Sources Test Equipment KEY SPECIFICATIONS * * * * * * * Resolution: 12 bits INL: 8 LSB (max) DNL: +0.6 / -0.5 LSB (max) Settling Time: 8.5 s (max) Zero Code Error: +10 mV (max) Full-Scale Error: -0.7 %FS (max) Supply Power - Normal: 380 W (3V) / 730 W (5V) typ - Power Down: 0.5 W (3V) / 0.9 W (5V) typ As an alternative, the DAC121C085 provides nine I2C addressing options and uses an external reference. It has the same performance and settling time as the DAC121C081. It is available in an 8-lead VSSOP. The DAC121C081 and DAC121C085 use a 2-wire, I2C-compatible serial interface that operates in all three speed modes, including high speed mode (3.4MHz). An external address selection pin allows up to three DAC121C081 or nine DAC121C085 devices per 2-wire bus. Pin compatible alternatives to the DAC121C081 are available that provide additional address options. The DAC121C081 and DAC121C085 each have a 16-bit register that controls the mode of operation, the power-down condition, and the output voltage. A power-on reset circuit ensures that the DAC output powers up to zero volts. A power-down feature reduces power consumption to less than a microWatt. Their low power consumption and small packages make these DACs an excellent choice for use in battery operated equipment. Each DAC operates over the extended industrial temperature range of -40C to +125C. The DAC121C081 and DAC121C085 are each part of a family of pin compatible DACs that also provide 8 and 10 bit resolution. For 8-bit DACs see the DAC081C081 and DAC081C085. For 10-bit DACs see the DAC101C081 and DAC101C085. 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. I C is a registered trademark of Phillips Corporation.. All other trademarks are the property of their respective owners. 2 2 3 PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2007-2013, Texas Instruments Incorporated DAC121C081, DAC121C085 SNAS395D - DECEMBER 2007 - REVISED MARCH 2013 www.ti.com Pin-Compatible Alternatives All devices are fully pin and function compatible. Resolution SOT-6 and WSONP-6 Packages VSSOP-8 Package w/ External Reference 12-bit DAC121C081 DAC121C085 10-bit DAC101C081 DAC101C085 8-bit DAC081C081 DAC081C085 Connection Diagrams 6 VOUT ADR0 1 SCL SDA 2 WSON 5 3 4 VOUT 1 VA VA GND 2 6 SOT 3 GND DAC121C081 5 4 ADR0 ADR0 1 8 VOUT ADR1 2 7 VREF VSSOP SCL SDA SCL 3 6 VA SDA 4 5 GND DAC121C081 DAC121C085 Block Diagram VA* VREF* GND DAC121C081 / DAC121C085 POWER-ON RESET REF DAC REGISTER 12 BIT DAC VOUT BUFFER 12 12 2.5k 100k POWER-DOWN CONTROL LOGIC 2 I C INTERFACE * NOTE: ADR1 and VREF are for the DAC121C085 only. The DAC121C085 uses an external reference (VREF), whereas, the DAC121C081 uses the supply (VA) as the reference. ADR1* ADR0 2 SCL SDA Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: DAC121C081 DAC121C085 DAC121C081, DAC121C085 www.ti.com SNAS395D - DECEMBER 2007 - REVISED MARCH 2013 PIN DESCRIPTIONS Symbol Type Equivalent Circuit VOUT Analog Output VA Supply Power supply input. For the SOT and WSON versions, this supply is used as the reference. Must be decoupled to GND. GND Ground Ground for all on-chip circuitry. SDA Digital Input/Output Analog Output Voltage. Serial Data bi-directional connection. Data is clocked into or out of the internal 16-bit register relative to the clock edges of SCL. This is an open drain data line that must be pulled to the supply (VA) by an external pull-up resistor. PIN D1 Snap Back SCL Description Serial Clock Input. SCL is used together with SDA to control the transfer of data in and out of the device. Digital Input GND ADR0 Digital Input, three levels PIN ADR1 Tri-state Address Selection Input. Sets the two Least Significant Bits (A1 & A0) of the 7-bit slave address. (see Table 1) V+ Snap Back Digital Input, three levels 2.1k D1 41.5k Tri-state Address Selection Input. Sets Bits A6 & A3 of the 7-bit slave address. (see Table 1) 41.5k GND VREF Supply Unbufferred reference voltage. For the VSSOP, this supply is used as the reference. VREF must be free of noise and decoupled to GND. PAD (LLP only) Ground Exposed die attach pad can be connected to ground or left floating. Soldering the pad to the PCB offers optimal thermal performance and enhances package self-alignment during reflow. Package Pinouts VOUT VA GND SDA SCL ADR0 ADR1 VREF PAD (WSON only) SOT 1 2 3 4 5 6 N/A N/A N/A WSON 6 5 4 3 2 1 N/A N/A 7 VSSOP 8 6 5 4 3 1 2 7 N/A These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: DAC121C081 DAC121C085 Submit Documentation Feedback 3 DAC121C081, DAC121C085 SNAS395D - DECEMBER 2007 - REVISED MARCH 2013 www.ti.com Absolute Maximum Ratings (1) (2) (3) Supply Voltage, VA -0.3V to +6.5V Voltage on any Input Pin -0.3V to +6.5V Input Current at Any Pin (4) 10 mA Package Input Current (4) 20 mA See (5) Power Consumption at TA = 25C Human Body Model VA, GND, VREF, VOUT, ADR0, ADR1 pins ESD Susceptibility (6) SDA, SCL pins Machine Model 2500V 250V Charged Device Model (CDM) 1000V Human Body Model 5000V Machine Model Charged Device Model (CDM) 350V 1000V Junction Temperature +150C Storage Temperature -65C to +150C (1) (2) (3) (4) (5) (6) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Operation of the device beyond the maximum Operating Ratings is not recommended. All voltages are measured with respect to GND = 0V, unless otherwise specified. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. When the input voltage at any pin exceeds 5.5V or is less than GND, the current at that pin should be limited to 10 mA. The 20 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 10 mA to two. The absolute maximum junction temperature (TJmax) for this device is 150C. The maximum allowable power dissipation is dictated by TJmax, the junction-to-ambient thermal resistance (JA), and the ambient temperature (TA), and can be calculated using the formula PDMAX = (TJmax - TA) / JA. The values for maximum power dissipation will be reached only when the device is operated in a severe fault condition (e.g., when input or output pins are driven beyond the operating ratings, or the power supply polarity is reversed). Human body model is a 100 pF capacitor discharged through a 1.5 k resistor. Machine model is a 220 pF capacitor discharged through 0 . Charge device model simulates a pin slowly acquiring charge (such as from a device sliding down the feeder in an automated assembler) then rapidly being discharged. Operating Ratings (1) (2) -40C TA +125C Operating Temperature Range Supply Voltage, VA +2.7V to 5.5V Reference Voltage, VREFIN Digital Input Voltage +1.0V to VA (3) 0.0V to 5.5V Output Load (1) (2) (3) 0 to 1500 pF Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Operation of the device beyond the maximum Operating Ratings is not recommended. All voltages are measured with respect to GND = 0V, unless otherwise specified. The inputs are protected as shown below. Input voltage magnitudes up to 5.5V, regardless of VA, will not cause errors in the conversion result. For example, if VA is 3V, the digital input pins can be driven with a 5V logic device. I/O TO INTERNAL CIRCUITRY GND 4 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: DAC121C081 DAC121C085 DAC121C081, DAC121C085 www.ti.com SNAS395D - DECEMBER 2007 - REVISED MARCH 2013 Package Thermal Resistances (1) (2) (1) (2) Package JA 6-Lead SOT 250C/W 6-Lead WSON 190C/W 8-Lead VSSOP 240C/W Soldering process must comply with Texas Instruments' Reflow Temperature Profile specifications. Refer to http://www.ti.com/packaging (SNOA549) Reflow temperature profiles are different for lead-free packages. Electrical Characteristics Values shown in this table are design targets and are subject to change before product release. The following specifications apply for VA = +2.7V to +5.5V, VREF = VA, CL = 200 pF to GND, input code range 48 to 4047. Boldface limits apply for TMIN TA TMAX and all other limits are at TA = 25C, unless otherwise specified. Limits (1) Units (Limits) Resolution 12 Bits (min) Monotonicity 12 Bits (min) +2.2 +8 LSB (max) -1.5 -8 LSB (min) +0.18 +0.6 LSB (max) LSB (min) Symbol Parameter Conditions Typical (1) STATIC PERFORMANCE INL DNL Integral Non-Linearity Differential Non-Linearity -0.12 -0.5 ZE Zero Code Error IOUT = 0 +1.1 +10 mV (max) FSE Full-Scale Error IOUT = 0 -0.1 -0.7 %FSR (max) GE Gain Error All ones Loaded to DAC register -0.2 -0.7 %FSR (max) ZCED TC GE -20 V/C VA = 3V -0.7 ppm FSR/C VA = 5V -1.0 ppm FSR/C Zero Code Error Drift Gain Error Tempco ANALOG OUTPUT CHARACTERISTICS (VOUT) Output Voltage Range ZCO Zero Code Output FSO Full Scale Output DAC121C085 0 VREF V (min) V (max) DAC121C081 0 VA V (min) V (max) (2) VA = 3V, IOUT = 200 A 1.3 mV VA = 5V, IOUT = 200 A 7.0 mV VA = 3V, IOUT = 200 A 2.984 V VA = 5V, IOUT = 200 A 4.989 V 56 mA IOS Output Short Circuit Current (ISOURCE) VA = 3V, VOUT = 0V, Input Code = FFFh. VA = 5V, VOUT = 0V, Input Code = FFFh. 69 mA IOS Output Short Circuit Current (ISINK) VA = 3V, VOUT = 3V, Input Code = 000h. -52 mA VA = 5V, VOUT = 5V, Input Code = 000h. -75 mA IO CL ZOUT Continuous Output Current (2) Available on the DAC output Maximum Load Capacitance 11 mA (max) RL = 1500 pF RL = 2k 1500 pF 7.5 DC Output Impedance REFERENCE INPUT CHARACTERISTICS- (DAC121C085 only) Input Range Minimum VREF 0.2 Input Range Maximum Input Impedance (1) (2) 120 1.0 V (min) VA V (max) k Typical figures are at TJ = 25C, and represent most likely parametric norms. Test limits are specified to AOQL (Average Outgoing Quality Level). This parameter is specified by design and/or characterization and is not tested in production. Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: DAC121C081 DAC121C085 Submit Documentation Feedback 5 DAC121C081, DAC121C085 SNAS395D - DECEMBER 2007 - REVISED MARCH 2013 www.ti.com Electrical Characteristics (continued) Values shown in this table are design targets and are subject to change before product release. The following specifications apply for VA = +2.7V to +5.5V, VREF = VA, CL = 200 pF to GND, input code range 48 to 4047. Boldface limits apply for TMIN TA TMAX and all other limits are at TA = 25C, unless otherwise specified. Symbol Parameter Typical (1) Conditions Limits (1) Units (Limits) LOGIC INPUT CHARACTERISTICS (SCL, SDA) VIH Input High Voltage 0.7 x VA V (min) VIL Input Low Voltage 0.3 x VA V (max) IIN Input Current 1 A (max) CIN Input Pin Capacitance (3) 3 pF (max) 0.1 x VA V (min) V (min) VHYST Input Hysteresis LOGIC INPUT CHARACTERISTICS (ADR0, ADR1) VIH Input High Voltage VA- 0.5V VIL Input Low Voltage 0.5 V (max) IIN Input Current 1 A (max) ISINK = 3 mA 0.4 V (max) ISINK = 6 mA 0.6 V (max) 1 A (max) LOGIC OUTPUT CHARACTERISTICS (SDA) VOL Output Low Voltage IOZ High-Impedence Output Leakage Current POWER REQUIREMENTS VA Supply Voltage Minimum 2.7 V (min) Supply Voltage Maximum 5.5 V (max) Normal -- VOUT set to midscale. 2-wire interface quiet (SCL = SDA = VA). (output unloaded) VA = 2.7V to 3.6V 105 156 A (max) VA = 4.5V to 5.5V 132 214 A (max) VA = 2.7V to 3.6V 86 118 A (max) VA = 4.5V to 5.5V 98 152 A (max) VREF Supply Current (DAC121C085 only) VA = 2.7V to 3.6V 37 43 A (max) VA = 4.5V to 5.5V 53 61 A (max) Power Consumption (VA & VREF for DAC121C085) (4) VA = 3.0V 380 W VA = 5.0V 730 W IST_VA-1 VADAC121C081 Supply Current IST_VA-5 VADAC121C085 Supply Current IST_VREF PST Continuous Operation -- 2-wire interface actively addressing the DAC and writing to the DAC register. (output unloaded) fSCL=400kHz ICO_VA-1 VADAC121C081 Supply Current fSCL=3.4MHz fSCL=400kHz ICO_VA-5 VADAC121C085 Supply Current fSCL=3.4MHz ICO_VREF VREF Supply Current (DAC121C085 only) fSCL=400kHz PCO Power Consumption (VA & VREF for DAC121C085) fSCL=3.4MHz (3) (4) 6 VA = 2.7V to 3.6V 134 220 A (max) VA = 4.5V to 5.5V 192 300 A (max) VA = 2.7V to 3.6V 225 320 A (max) VA = 4.5V to 5.5V 374 500 A (max) VA = 2.7V to 3.6V 101 155 A (max) VA = 4.5V to 5.5V 142 220 A (max) VA = 2.7V to 3.6V 193 235 A (max) VA = 4.5V to 5.5V 325 410 A (max) VA = 2.7V to 3.6V 33.5 55 A (max) VA = 4.5V to 5.5V 49.5 71.4 A (max) VA = 3.0V 480 W VA = 5.0V 1.06 mW VA = 3.0V 810 W VA = 5.0V 2.06 mW This parameter is specified by design and/or characterization and is not tested in production. To ensure accuracy, it is required that VA and VREF be well bypassed. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: DAC121C081 DAC121C085 DAC121C081, DAC121C085 www.ti.com SNAS395D - DECEMBER 2007 - REVISED MARCH 2013 Electrical Characteristics (continued) Values shown in this table are design targets and are subject to change before product release. The following specifications apply for VA = +2.7V to +5.5V, VREF = VA, CL = 200 pF to GND, input code range 48 to 4047. Boldface limits apply for TMIN TA TMAX and all other limits are at TA = 25C, unless otherwise specified. Symbol Parameter Conditions Typical (1) Limits (1) Units (Limits) Power Down -- 2-wire interface quiet (SCL = SDA = VA) after PD mode written to DAC register. (output unloaded) IPD PPD Supply Current (VA & VREF for DAC121C085) All Power Down Modes Power Consumption (VA & VREF for DAC121C085) All Power Down Modes VA = 2.7V to 3.6V 0.13 1.52 A (max) VA = 4.5V to 5.5V 0.15 3.25 A (max) VA = 3.0V 0.5 W VA = 5.0V 0.9 W A.C. and Timing Characteristics Values shown in this table are design targets and are subject to change before product release. The following specifications apply for VA = +2.7V to +5.5V, VREF = VA, RL = Infinity, CL = 200 pF to GND. Boldface limits apply for TMIN TA TMAX and all other limits are at TA = 25C, unless otherwise specified. Symbol Typical (2) Limits (1) (2) Units (Limits) 400h to C00h code change RL = 2k, CL = 200 pF 6 8.5 s (max) 1 V/s Code change from 800h to 7FFh 12 nV-sec 0.5 nV-sec VREF = 2.5V 0.1Vpp 160 kHz VREF = 2.5V 0.1Vpp input frequency = 10kHz 70 dB VA = 3V 0.8 sec VA = 5V 0.5 sec Conditions (1) Parameter ts Output Voltage Settling Time (3) SR Output Slew Rate Glitch Impulse Digital Feedthrough Multiplying Bandwidth (4) Total Harmonic Distortion tWU (4) Wake-Up Time DIGITAL TIMING SPECS (SCL, SDA) Serial Clock Frequency Standard Mode Fast Mode High Speed Mode, Cb = 100pF High Speed Mode, Cb = 400pF 100 400 3.4 1.7 kHz (max) kHz (max) MHz (max) MHz (max) SCL Low Time Standard Mode Fast Mode High Speed Mode, Cb = 100pF High Speed Mode, Cb = 400pF 4.7 1.3 160 320 s (min) s (min) ns (min) ns (min) tHIGH SCL High Time Standard Mode Fast Mode High Speed Mode, Cb = 100pF High Speed Mode, Cb = 400pF 4.0 0.6 60 120 s (min) s (min) ns (min) ns (min) tSU;DAT Data Setup Time Standard Mode Fast Mode High Speed Mode 250 100 10 ns (min) ns (min) ns (min) fSCL tLOW (1) (2) (3) (4) Cb refers to the capacitance of one bus line. Cb is expressed in pF units. Typical figures are at TJ = 25C, and represent most likely parametric norms. Test limits are specified to AOQL (Average Outgoing Quality Level). This parameter is specified by design and/or characterization and is not tested in production. Applies to the Multiplying DAC configuration. In this configuration, the reference is used as the analog input. The value loaded in the DAC Register will digitally attenuate the signal at Vout. Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: DAC121C081 DAC121C085 Submit Documentation Feedback 7 DAC121C081, DAC121C085 SNAS395D - DECEMBER 2007 - REVISED MARCH 2013 www.ti.com A.C. and Timing Characteristics (continued) Values shown in this table are design targets and are subject to change before product release. The following specifications apply for VA = +2.7V to +5.5V, VREF = VA, RL = Infinity, CL = 200 pF to GND. Boldface limits apply for TMIN TA TMAX and all other limits are at TA = 25C, unless otherwise specified. Symbol tHD;DAT Limits (1) (2) Units (Limits) Standard Mode 0 3.45 s (min) s (max) Fast Mode 0 0.9 s (min) s (max) High Speed Mode, Cb = 100pF 0 70 ns (min) ns (max) High Speed Mode, Cb = 400pF 0 150 ns (min) ns (max) Conditions (1) Parameter Typical (2) Data Hold Time tSU;STA Setup time for a start or a repeated start condition Standard Mode Fast Mode High Speed Mode 4.7 0.6 160 s (min) s (min) ns (min) tHD;STA Hold time for a start or a repeated start condition Standard Mode Fast Mode High Speed Mode 4.0 0.6 160 s (min) s (min) ns (min) tBUF Bus free time between a stop and start condition Standard Mode Fast Mode 4.7 1.3 s (min) s (min) tSU;STO Setup time for a stop condition Standard Mode Fast Mode High Speed Mode 4.0 0.6 160 s (min) s (min) ns (min) Standard Mode 1000 ns (max) 20+0.1Cb 300 ns (min) ns (max) High Speed Mode, Cb = 100pF 10 80 ns (min) ns (max) High Speed Mode, Cb = 400pF 20 160 ns (min) ns (max) Standard Mode 250 ns (max) 20+0.1Cb 250 ns (min) ns (max) High Speed Mode, Cb = 100pF 10 80 ns (min) ns (max) High Speed Mode, Cb = 400pF 20 160 ns (min) ns (max) Standard Mode 1000 ns (max) 20+0.1Cb 300 ns (min) ns (max) High Speed Mode, Cb = 100pF 10 40 ns (min) ns (max) High Speed Mode, Cb = 400pF 20 80 ns (min) ns (max) 1000 ns (max) 20+0.1Cb 300 ns (min) ns (max) High Speed Mode, Cb = 100pF 10 80 ns (min) ns (max) High Speed Mode, Cb = 400pF 20 160 ns (min) ns (max) Fast Mode trDA Rise time of SDA signal Fast Mode tfDA Fall time of SDA signal Fast Mode trCL Rise time of SCL signal Standard Mode trCL1 8 Rise time of SCL signal after a repeated start condition and after an acknowledge bit. Submit Documentation Feedback Fast Mode Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: DAC121C081 DAC121C085 DAC121C081, DAC121C085 www.ti.com SNAS395D - DECEMBER 2007 - REVISED MARCH 2013 A.C. and Timing Characteristics (continued) Values shown in this table are design targets and are subject to change before product release. The following specifications apply for VA = +2.7V to +5.5V, VREF = VA, RL = Infinity, CL = 200 pF to GND. Boldface limits apply for TMIN TA TMAX and all other limits are at TA = 25C, unless otherwise specified. Symbol Limits (1) (2) Units (Limits) 300 ns (max) 20+0.1Cb 300 ns (min) ns (max) High Speed Mode, Cb = 100pF 10 40 ns (min) ns (max) High Speed Mode, Cb = 400pF 20 80 ns (min) ns (max) 400 pF (max) 50 10 ns (max) ns (max) 270 60 ns (max) ns (max) Conditions (1) Parameter Typical (2) Standard Mode Fast Mode tfCL Fall time of a SCL signal Cb Capacitive load for each bus line (SCL and SDA) tSP Pulse Width of spike suppressed (5) (6) Fast Mode High Speed Mode toutz SDA output delay (see the ADDITIONAL TIMING INFORMATION: toutz section) Fast Mode High Speed Mode (5) (6) 87 38 Spike suppression filtering on SCL and SDA will supress spikes that are less than 50ns for standard-fast mode and less than 10ns for hs-mode. This parameter is specified by design and/or characterization and is not tested in production. Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: DAC121C081 DAC121C085 Submit Documentation Feedback 9 DAC121C081, DAC121C085 SNAS395D - DECEMBER 2007 - REVISED MARCH 2013 www.ti.com Specification Definitions DIFFERENTIAL NON-LINEARITY (DNL) is the measure of the maximum deviation from the ideal step size of 1 LSB, which is VREF / 4096 = VA / 4096. DIGITAL FEEDTHROUGH is a measure of the energy injected into the analog output of the DAC from the digital inputs when the DAC output is not updated. It is measured with a full-scale code change on the data bus. FULL-SCALE ERROR is the difference between the actual output voltage with a full scale code (FFFh) loaded into the DAC and the value of VA x 4095 / 4096. GAIN ERROR is the deviation from the ideal slope of the transfer function. It can be calculated from Zero and Full-Scale Errors as GE = FSE - ZE, where GE is Gain error, FSE is Full-Scale Error and ZE is Zero Error. GLITCH IMPULSE is the energy injected into the analog output when the input code to the DAC register changes. It is specified as the area of the glitch in nanovolt-seconds. INTEGRAL NON-LINEARITY (INL) is a measure of the deviation of each individual code from a straight line through the input to output transfer function. The deviation of any given code from this straight line is measured from the center of that code value. The end point method is used. INL for this product is specified over a limited range, per the Electrical Characteristics. LEAST SIGNIFICANT BIT (LSB) is the bit that has the smallest value or weight of all bits in a word. This value is LSB = VREF / 2n (1) where VREF is the supply voltage for this product, and "n" is the DAC resolution in bits, which is 12 for the DAC121C081. MAXIMUM LOAD CAPACITANCE is the maximum capacitance that can be driven by the DAC with output stability maintained. MONOTONICITY is the condition of being monotonic, where the DAC has an output that never decreases when the input code increases. MOST SIGNIFICANT BIT (MSB) is the bit that has the largest value or weight of all bits in a word. Its value is 1/2 of VA. MULTIPLYING BANDWIDTH is the frequency at which the output amplitude falls 3dB below the input sine wave on VREFIN with a full-scale code loaded into the DAC. POWER EFFICIENCY is the ratio of the output current to the total supply current. The output current comes from the power supply. The difference between the supply and output currents is the power consumed by the device without a load. SETTLING TIME is the time for the output to settle to within 1/2 LSB of the final value after the input code is updated. TOTAL HARMONIC DISTORTION (THD) is the measure of the harmonics present at the output of the DACs with an ideal sine wave applied to VREFIN. THD is measured in dB. WAKE-UP TIME is the time for the output to exit power-down mode. This time is measured from the rising edge of SCL during the ACK bit of the lower data byte to the time the output voltage deviates from the power-down voltage of 0V. ZERO CODE ERROR is the output error, or voltage, present at the DAC output after a code of 000h has been entered. 10 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: DAC121C081 DAC121C085 DAC121C081, DAC121C085 www.ti.com SNAS395D - DECEMBER 2007 - REVISED MARCH 2013 Transfer Characteristic FSE 4095 x VREF 4096 GE = FSE - ZE FSE = GE + ZE OUTPUT VOLTAGE ZE 0 0 4095 DIGITAL INPUT CODE Figure 1. Input / Output Transfer Characteristic Timing Diagrams SDA tLOW tf tr tHD;STA tr tf tBUF tSP SCL tSU;STA tHD;STA tHIGH tHD;DAT tSU;DAT REPEATED START START tSU;STO STOP START Figure 2. Serial Timing Diagram Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: DAC121C081 DAC121C085 Submit Documentation Feedback 11 DAC121C081, DAC121C085 SNAS395D - DECEMBER 2007 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics VREF = VA, fSCL = 3.4MHz, TA = 25C, Input Code Range 48 to 4047, unless otherwise stated. 12 INL DNL Figure 3. Figure 4. INL/DNL vs Temperature at VA = 3.0V INL/DNL vs Temperature at VA = 5.0V Figure 5. Figure 6. INL/DNL vs VREFIN at VA = 3.0V INL/DNL vs VREFIN at VA = 5.0V Figure 7. Figure 8. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: DAC121C081 DAC121C085 DAC121C081, DAC121C085 www.ti.com SNAS395D - DECEMBER 2007 - REVISED MARCH 2013 Typical Performance Characteristics (continued) VREF = VA, fSCL = 3.4MHz, TA = 25C, Input Code Range 48 to 4047, unless otherwise stated. INL/DNL vs VA Zero Code Error vs. VA Figure 9. Figure 10. Zero Code Error vs. Temperature Full Scale Error vs. VA Figure 11. Figure 12. Full Scale Error vs. Temperature Total Supply Current vs. VA Figure 13. Figure 14. Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: DAC121C081 DAC121C085 Submit Documentation Feedback 13 DAC121C081, DAC121C085 SNAS395D - DECEMBER 2007 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics (continued) VREF = VA, fSCL = 3.4MHz, TA = 25C, Input Code Range 48 to 4047, unless otherwise stated. VREF Supply Current vs. VA Total Supply Current vs. Temperature @ VA = 3V Figure 15. Figure 16. Total Supply Current vs. Temperature @ VA = 5V 5V Glitch Response Figure 17. Figure 18. Power-On Reset Figure 19. 14 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: DAC121C081 DAC121C085 DAC121C081, DAC121C085 www.ti.com SNAS395D - DECEMBER 2007 - REVISED MARCH 2013 FUNCTIONAL DESCRIPTION DAC SECTION The DAC121C081 is fabricated on a CMOS process with an architecture that consists of switches and resistor strings that are followed by an output buffer. For simplicity, a single resistor string is shown in Figure 20. This string consists of 4096 equal valued resistors with a switch at each junction of two resistors, plus a switch to ground. The code loaded into the DAC register determines which switch is closed, connecting the proper node to the amplifier. The input coding is straight binary with an ideal output voltage of: VOUT = VREF x (D / 4096) (2) where D is the decimal equivalent of the binary code that is loaded into the DAC register. D can take on any integer value between 0 and 4095. This configuration ensures that the DAC is monotonic. VREF R R R To Output Amplifier R R Figure 20. DAC Resistor String OUTPUT AMPLIFIER The output amplifier is rail-to-rail, providing an output voltage range of 0V to VA when the reference is VA. All amplifiers, even rail-to-rail types, exhibit a loss of linearity as the output approaches the supply rails (0V and VA, in this case). For this reason, linearity is specified over less than the full output range of the DAC. However, if the reference is less than VA, there is only a loss in linearity in the lowest codes. The output capabilities of the amplifier are described in the Electrical Characteristics. The output amplifiers are capable of driving a load of 2 k in parallel with 1500 pF to ground or to VA. The zerocode and full-scale outputs for given load currents are available in the Electrical Characteristics. REFERENCE VOLTAGE The DAC121C081 uses the supply (VA) as the reference. With that said, VA must be treated as a reference. The Analog output will only be as clean as the reference (VA). It is recommended that the reference be driven by a voltage source with low output impedance. Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: DAC121C081 DAC121C085 Submit Documentation Feedback 15 DAC121C081, DAC121C085 SNAS395D - DECEMBER 2007 - REVISED MARCH 2013 www.ti.com The DAC121C085 comes with an external reference supply pin (VREF). For the DAC121C085, it is important that VREF be kept as clean as possible. The Applications Information section describes a handful of ways to drive the reference appropriately. Refer to the USING REFERENCES AS POWER SUPPLIES section for details. SERIAL INTERFACE The I2C-compatible interface operates in all three speed modes. Standard mode (100kHz) and Fast mode (400kHz) are functionally the same and will be referred to as Standard-Fast mode in this document. High-Speed mode (3.4MHz) is an extension of Standard-Fast mode and will be referred to as Hs-mode in this document. The following diagrams describe the timing relationships of the clock (SCL) and data (SDA) signals. Pull-up resistors or current sources are required on the SCL and SDA busses to pull them high when they are not being driven low. A logic zero is transmitted by driving the output low. A logic high is transmitted by releasing the output and allowing it to be pulled-up externally. The appropriate pull-up resistor values will depend upon the total bus capacitance and operating speed. Basic I2C Protocol The I2C interface is bi-directional and allows multiple devices to operate on the same bus. To facilitate this bus configuration, each device has a unique hardware address which is referred to as the "slave address." To communicate with a particular device on the bus, the controller (master) sends the slave address and listens for a response from the slave. This response is referred to as an acknowledge bit. If a slave on the bus is addressed correctly, it Acknowledges (ACKs) the master by driving the SDA bus low. If the address doesn't match a device's slave address, it Not-acknowledges (NACKs) the master by letting SDA be pulled high. ACKs also occur on the bus when data is being transmitted. When the master is writing data, the slave ACKs after every data byte is successfully received. When the master is reading data, the master ACKs after every data byte is received to let the slave know it wants to receive another data byte. When the master wants to stop reading, it NACKs after the last data byte and creates a Stop condition on the bus. All communication on the bus begins with either a Start condition or a Repeated Start condition. The protocol for starting the bus varies between Standard-Fast mode and Hs-mode. In Standard-Fast mode, the master generates a Start condition by driving SDA from high to low while SCL is high. In Hs-mode, starting the bus is more complicated. Please refer to the High-Speed (Hs) Mode section for the full details of a Hs-mode Start condition. A Repeated Start is generated to either address a different device, or switch between read and write modes. The master generates a Repeated Start condition by driving SDA low while SCL is high. Following the Repeated Start, the master sends out the slave address and a read/write bit as shown in Figure 21. The bus continues to operate in the same speed mode as before the Repeated Start condition. All communication on the bus ends with a Stop condition. In either Standard-Fast mode or Hs-Mode, a Stop condition occurs when SDA is pulled from low to high while SCL is high. After a Stop condition, the bus remains idle until a master generates a Start condition. Please refer to the Phillips I2C(R) Specification (Version 2.1 Jan, 2000) for a detailed description of the serial interface. SDA 1 2 6 MSB R/W Direction Bit Acknowledge from the Device 7-bit Slave Address SCL ACK LSB MSB 7 8 9 LSB N/ACK Data Byte *Acknowledge or Not-ACK 1 2 8 Repeated for the Lower Data Byte and Additional Data Transfers START or REPEATED START 9 STOP *Note: In continuous mode, this bit must be an ACK from the data receiver. Immediately preceding a STOP condition, this bit must be a NACK from the master. Figure 21. Basic Operation. 16 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: DAC121C081 DAC121C085 DAC121C081, DAC121C085 www.ti.com SNAS395D - DECEMBER 2007 - REVISED MARCH 2013 Standard-Fast Mode In Standard-Fast mode, the master generates a start condition by driving SDA from high to low while SCL is high. The Start condition is always followed by a 7-bit slave address and a Read/Write bit. After these eight bits have been transmitted by the master, SDA is released by the master and the DAC121C081 either ACKs or NACKs the address. If the slave address matches, the DAC121C081 ACKs the master. If the address doesn't match, the DAC121C081 NACKs the master. For a write operation, the master follows the ACK by sending the upper eight data bits to the DAC121C081. Then the DAC121C081 ACKs the transfer by driving SDA low. Next, the lower eight data bits are sent by the master. The DAC121C081 then ACKs the transfer. At this point, the DAC output updates to reflect the contents of the 16-bit DAC register. Next, the master either sends another pair of data bytes, generates a Stop condition to end communication, or generates a Repeated Start condition to communicate with another device on the bus. For a read operation, the DAC121C081 sends out the upper eight data bits of the DAC register. This is followed by an ACK by the master. Next, the lower eight data bits of the DAC register are sent to the master. The master then produces a NACK by letting SDA be pulled high. The NACK is followed by a master-generated Stop condition to end communication on the bus, or a Repeated Start to communicate with another device on the bus. High-Speed (Hs) Mode For Hs-mode, the sequence of events to begin communication differ slightly from Standard-Fast mode. Figure 22 describes this in further detail. Initially, the bus begins running in Standard-Fast mode. The master generates a Start condition and sends the 8-bit Hs master code (00001XXX) to the DAC121C081. Next, the DAC121C081 responds with a NACK. Once the SCL line has been pulled to a high level, the master switches to Hs-mode by increasing the bus speed and generating a Repeated Start condition (driving SDA low while SCL is pulled high). At this point, the master sends the slave address to the DAC121C081, and communication continues as shown above in the "Basic Operation" Diagram (see Figure 21). When the master generates a Repeated Start condition while in Hs-mode, the bus stays in Hs-mode awaiting the slave address from the master. The bus continues to run in Hs-mode until a Stop condition is generated by the master. When the master generates a Stop condition on the bus, the bus must be started in Standard-Fast mode again before increasing the bus speed and switching to Hs-mode. ns16705 SDA NACK MSB 8-ELW 0DVWHU FRGH 00001[[[ 7-bit Slave Address Not-Acknowledge from the Device 1 SCL 2 5 6 7 8 9 1 2 Repeated START START Standard-Fast Mode Hs-Mode Figure 22. Beginning Hs-Mode Communication I2C Slave (Hardware) Address The DAC has a seven-bit I2C slave address. For the VSSOP version of the DAC, this address is configured by the ADR0 and ADR1 address selection inputs. For the DAC121C081, the address is configured by the ADR0 address selection input. ADR0 and ADR1 can be grounded, left floating, or tied to VA. If desired, the address selection inputs can be set to VA/2 rather than left floating. The state of these inputs sets the address the DAC responds to on the I2C bus (see Table 1). In addition to the selectable slave address, there is also a broadcast address (1001000) for all DAC121C081's and DAC121C085's on the 2-wire bus. When the bus is addressed by the broadcast address, all the DAC121C081's and DAC121C085's will respond and update synchronously. Figure 23 and Figure 24 describe how the master device should address the DAC via the I2C-Compatible interface. Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: DAC121C081 DAC121C085 Submit Documentation Feedback 17 DAC121C081, DAC121C085 SNAS395D - DECEMBER 2007 - REVISED MARCH 2013 www.ti.com Keep in mind that the address selection inputs (ADR0 and ADR1) are only sampled until the DAC is correctly addressed with a non-broadcast address. At this point, the ADR0 and ADR1 inputs TRI-STATE and the slave address is "locked". Changes to ADR0 and ADR1 will not update the selected slave address until the device is power-cycled. Table 1. Slave Addresses DAC121C085 (VSSOP) DAC121C081 (SOT & WSON) * Slave Address [A6 - A0] ADR1 ADR0 ADR0 0001100 Floating Floating Floating 0001101 Floating GND GND 0001110 Floating VA VA 0001000 GND Floating --------------- 0001001 GND GND --------------- 0001010 GND VA --------------- 1001100 VA Floating --------------- 1001101 VA GND --------------- 1001110 VA VA --------------- 1001000 --------------- Broadcast Address --------------- * Pin-compatible alternatives to the DAC121C081 options are available with additional address options. Writing to the DAC Register To write to the DAC, the master addresses the part with the correct slave address (A6-A0) and writes a "zero" to the read/write bit. If addressed correctly, the DAC returns an ACK to the master. The master then sends out the upper data byte. The DAC responds by sending an ACK to the master. Next, the master sends the lower data byte to the DAC. The DAC responds by sending an ACK again. At this point, the master either sends the upper byte of the next data word to be converted by the DAC, generates a Stop condition to end communication, or generates a Repeated Start condition to begin communication with another device on the bus. Until generating a Stop condition, the master can continuously write the upper and lower data bytes to the DAC register. This allows for a maximum DAC conversion rate of 188.9 kilo-conversions per second in Hs-mode. 1 9 1 9 1 9 SCL SDA A6 Start by Master A5 A4 A3 A2 A1 A0 R/W 0 ACK by DAC121C081 Frame 1 Address Byte from Master 0 PD1 PD0 D11 D10 D9 Frame 2 Data Byte from Master D7 ACK by DAC121C081 D8 D6 D5 D4 D3 D2 Frame 3 Data Byte from Master D1 D0 ACK Stop by by Master DAC121C081 Repeat Frames 2 & 3 for Continuous Mode Figure 23. Typical Write to the DAC Register Reading from the DAC Register To read from the DAC register, the master addresses the part with the correct slave address (A6-A0) and writes a "one" to the read/write bit. If addressed correctly, the DAC returns an ACK to the master. Next, the DAC sends out the upper data byte. The master responds by sending an ACK to the DAC to indicate that it wants to receive another data byte. Then the DAC sends the lower data byte to the master. Assuming only one 16-bit data word is read, the master sends a NACK after receiving the lower data byte. At this point, the master either generates a Stop condition to end communication, or a Repeated Start condition to begin communication with another device on the bus. 18 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: DAC121C081 DAC121C085 DAC121C081, DAC121C085 www.ti.com SNAS395D - DECEMBER 2007 - REVISED MARCH 2013 1 9 1 9 1 9 SCL SDA A6 A5 A4 A3 A2 A1 A0 R/W 0 ACK by DAC121C081 Start by Master Frame 1 Address Byte from Master 0 PD1 PD0 D11 D10 D9 Frame 2 Data Byte from DAC121C081 D8 D7 D6 D5 ACK by Master D4 D3 D2 Frame 3 Data Byte from DAC121C081 D1 D0 NACK by Master Stop by Master Figure 24. Typical Read from the DAC Register DAC REGISTER The DAC register, Figure 25, has sixteen bits. The first two bits are always zero. The next two bits determine the mode of operation (normal mode or one of three power-down modes). The final twelve bits of the shift register are the data bits. The data format is straight binary (MSB first, LSB last), with twelve 0's corresponding to an output of 0V and twelve 1's corresponding to a full-scale output of VA - 1 LSB. When writing to the DAC Register, VOUT will update on the rising edge of the ACK following the lower data byte. LSB MSB X X PD1 PD0 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 DATA BITS 0 0 1 1 0 1 0 1 Normal Operation. 2.5kO to GND. 100kO to GND. High Impedance. Power-Down Modes Figure 25. DAC Register Contents POWER-ON RESET The power-on reset circuit controls the output voltage of the DAC during power-up. Upon application of power, the DAC register is filled with zeros and the output voltage is 0 Volts. The output remains at 0V until a valid write sequence is made to the DAC. When resetting the device, it is crutial that the VA supply be lowered to a maximum of 200mV before the supply is raised again to power-up the device. Dropping the supply to within 200mV of GND during a reset will ensure the ADC performs as specified. SIMULTANEOUS RESET The broadcast address allows the I2C master to write a single word to multiple DACs simultaneously. Provided that all of the DACs exist on a single I2C bus, every DAC will update when the broadcast address is used to address the bus. This feature allows the master to reset all of the DACs on a shared I2C bus to a specific digital code. For instance, if the master writes a power-down code to the bus with the broadcast address, all of the DACs will power-down simultaneously. POWER-DOWN MODES The DAC121C081 has three power-down modes. In power-down mode, the supply current drops to 0.13A at 3V and 0.15A at 5V (typ). The DAC121C081 is put into power-down mode by writing a one to PD1 and/or PD0. The outputs can be set to high impedance, terminated by 2.5 k to GND, or terminated by 100 k to GND (see Figure 25). The bias generator, output amplifier, resistor string, and other linear circuitry are all shut down in any of the power-down modes. When the DAC121C081 is powered down, the value written to the DAC register, including the power-down bits, is saved. While the DAC is in power-down, the saved DAC register contents can be read back. When the DAC is brought out of power-down mode, the DAC register contents will be overwritten and VOUT will be updated with the new 12-bit data value. The time to exit power-down (Wake-Up Time) is typically 0.8sec at 3V and 0.5sec at 5V. Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: DAC121C081 DAC121C085 Submit Documentation Feedback 19 DAC121C081, DAC121C085 SNAS395D - DECEMBER 2007 - REVISED MARCH 2013 www.ti.com ADDITIONAL TIMING INFORMATION: toutz The toutz specification is provided to aid the design of the I2C bus. After the SCL bus is driven low by the I2C master, the SDA bus will be held for a short time by the DAC121C081. This time is referred to as toutz. The following figure illustrates the relationship between the fall of SCL, at the 30% threshold, to the time when the DAC begins to transition the SDA bus. The toutz specification only applies when the DAC is in control of the SDA bus. The DAC is only in control of the bus during an ACK by the DAC121C081 or a data byte read from the DAC (see Figure 24). SCL SDA toutz Figure 26. Data Output Timing The toutz specification is typically 87nsec in Standard-Fast Mode and 38nsec in Hs-Mode. Applications Information USING REFERENCES AS POWER SUPPLIES While the simplicity of the DAC121C081 implies ease of use, it is important to recognize that the path from the reference input (VA for the DAC121C081 & VREF for the DAC121C085) to VOUT will have essentially zero Power Supply Rejection Ratio (PSRR). Therefore, it is necessary to provide a noise-free supply voltage to the reference. In order to use the full dynamic range of the DAC121C085, the supply pin (VA) and VREF can be connected together and share the same supply voltage. Since the DAC121C081 consumes very little power, a reference source may be used as the supply voltage. The advantages of using a reference source over a voltage regulator are accuracy and stability. Some low noise regulators can also be used. Listed below are a few reference and power supply options for the DAC121C081. When using the DAC121C081, it is important to treat the analog supply (VA) as the reference. LM4132 The LM4132, with its 0.05% accuracy over temperature, is a good choice as a reference source for the DAC121C081. The 4.096V version is useful if a 0 to 4.095V output range is desirable or acceptable. Bypassing the LM4132 VIN pin with a 0.1F capacitor and the VOUT pin with a 2.2F capacitor will improve stability and reduce output noise. The LM4132 comes in a space-saving 5-pin SOT-23. Input Voltage LM4132-4.1 C1 0.1 PF C2 2.2 PF C3 0.1 PF VA VREF DAC121C081/5 VOUT = 0V to 4.092V SDA SCL Figure 27. The LM4132 as a power supply LM4050 Available with accuracy of 0.44%, the LM4050 shunt reference is also a good choice as a reference for the DAC121C081. It is available in 4.096V and 5V versions and comes in a space-saving 3-pin SOT-23. 20 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: DAC121C081 DAC121C085 DAC121C081, DAC121C085 www.ti.com SNAS395D - DECEMBER 2007 - REVISED MARCH 2013 Input Voltage R IDAC VZ IZ 0.1 PF 0.47 PF VA VREF LM4050-4.1 or LM4050-5.0 DAC121C081/5 VOUT = 0V to 5V SDA SCL Figure 28. The LM4050 as a power supply The minimum resistor value in the circuit of Figure 28 must be chosen such that the maximum current through the LM4050 does not exceed its 15 mA rating. The conditions for maximum current include the input voltage at its maximum, the LM4050 voltage at its minimum, and the DAC121C081 drawing zero current. The maximum resistor value must allow the LM4050 to draw more than its minimum current for regulation plus the maximum DAC121C081 current in full operation. The conditions for minimum current include the input voltage at its minimum, the LM4050 voltage at its maximum, the resistor value at its maximum due to tolerance, and the DAC121C081 draws its maximum current. These conditions can be summarized as R(min) = ( VIN(max) - VZ(min) ) /IZ(max) (3) R(max) = ( VIN(min) - VZ(max) ) / ( (IDAC(max) + IZ(min) ) (4) and where VZ(min) and VZ(max) are the nominal LM4050 output voltages the LM4050 output tolerance over temperature, IZ(max) is the maximum allowable current through the LM4050, IZ(min) is the minimum current required by the LM4050 for proper regulation, and IDAC(max) is the maximum DAC121C081 supply current. LP3985 The LP3985 is a low noise, ultra low dropout voltage regulator with a 3% accuracy over temperature. It is a good choice for applications that do not require a precision reference for the DAC121C081. It comes in 3.0V, 3.3V and 5V versions, among others, and sports a low 30 V noise specification at low frequencies. Since low frequency noise is relatively difficult to filter, this specification could be important for some applications. The LP3985 comes in a space-saving 5-pin SOT-23 and 5-bump DSBGA packages. Input Voltage LP3985 0.1 PF 1 PF 0.01 PF 0.1 PF VA VREF DAC121C081/5 VOUT = 0V to 5V SDA SCL Figure 29. Using the LP3985 regulator An input capacitance of 1.0F without any ESR requirement is required at the LP3985 input, while a 1.0F ceramic capacitor with an ESR requirement of 5m to 500m is required at the output. Careful interpretation and understanding of the capacitor specification is required to ensure correct device operation. Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: DAC121C081 DAC121C085 Submit Documentation Feedback 21 DAC121C081, DAC121C085 SNAS395D - DECEMBER 2007 - REVISED MARCH 2013 www.ti.com LP2980 The LP2980 is an ultra low dropout regulator with a 0.5% or 1.0% accuracy over temperature, depending upon grade. It is available in 3.0V, 3.3V and 5V versions, among others. VIN Input Voltage VOUT LP2980 1 PF ON /OFF 0.1 PF VA VREF DAC121C081/5 VOUT = 0V to 5V SDA SCL Figure 30. Using the LP2980 regulator Like any low dropout regulator, the LP2980 requires an output capacitor for loop stability. This output capacitor must be at least 1.0F over temperature, but values of 2.2F or more will provide even better performance. The ESR of this capacitor should be within the range specified in the LP2980 data sheet. Surface-mount solid tantalum capacitors offer a good combination of small size and ESR. Ceramic capacitors are attractive due to their small size but generally have ESR values that are too low for use with the LP2980. Aluminum electrolytic capacitors are typically not a good choice due to their large size and have ESR values that may be too high at low temperatures. BIPOLAR OPERATION The DAC121C081 is designed for single supply operation and thus has a unipolar output. However, a bipolar output may be obtained with the circuit in Figure 31. This circuit will provide an output voltage range of 5 Volts. A rail-to-rail amplifier should be used if the amplifier supplies are limited to 5V. 10 pF R2 +5V R1 +5V 10 PF + - 0.1 PF 5V + DAC121C081 SDA -5V VOUT SCL Figure 31. Bipolar Operation The output voltage of this circuit for any code is found to be VO = (VA x (D / 4096) x ((R1 + R2) / R1) - VA x R2 / R1) (5) where D is the input code in decimal form. With VA = 5V and R1 = R2, VO = (10 x D / 4096) - 5V (6) A list of rail-to-rail amplifiers suitable for this application are indicated in Table 2. Table 2. Some Rail-to-Rail Amplifiers 22 AMP PKGS LMP7701 SOT-23 Typ VOS 37 uV Typ ISUPPLY 0.79 mA LMV841 SC70-5 50 uV 1 mA LMC7111 SOT-23 0.9 mV 25 A LM7301 SO-8, SOT-23 0.03 mV 620 A LM8261 SOT-23 0.7 mV 1 mA Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: DAC121C081 DAC121C085 DAC121C081, DAC121C085 www.ti.com SNAS395D - DECEMBER 2007 - REVISED MARCH 2013 DSP/MICROPROCESSOR INTERFACING Interfacing the DAC121C081 to microprocessors and DSPs is quite simple. The following guidelines are offered to simplify the design process. Interfacing to the 2-wire Bus Figure 32 shows a microcontroller interfacing to the DAC121C081 via the 2-wire bus. Pull-up resistors (Rp) should be chosen to create an appropriate bus rise time and to limit the current that will be sunk by the opendrain outputs of the devices on the bus. Please refer to the I2C(R) Specification for further details. Typical pull-up values to use in Standard-Fast mode bus applications are 2k to 10k. SCL and SDA series resisters (RS) near the DAC121C081 are optional. If high-voltage spikes are expected on the 2-wire bus, series resistors should be used to filter the voltage on SDA and SCL. The value of the series resistance must be picked to ensure the VIL threshold can be achieved. If used, RS is typically 51. DAC121C081/5 10 PF VREF 4.7 PF VA 0.1 PF Regulated Supply RP RP VDD uController R S* SDA SDA SCL SCL R S* ADC121C021 SDA SCL I2C Device SDA SCL *NOTE: RS is optional. Figure 32. Serial Interface Connection Diagram Interfacing to a Hs-mode Bus Interfacing to a Hs-mode bus is very similar to interfacing to a Standard-Fast mode bus. In Hs-mode, the specified rise time of SCL is shortened. To create a faster rise time, the master device (microcontroller) can drive the SCL bus high and low. In other words, the microcontroller can drive the line high rather than leaving it to the pull-up resistor. It is also possible to decrease the value of the pull-up resistors or increase the pull-up current to meet the tighter timing specs. Please refer to the I2C(R) Specification for further details. Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: DAC121C081 DAC121C085 Submit Documentation Feedback 23 DAC121C081, DAC121C085 SNAS395D - DECEMBER 2007 - REVISED MARCH 2013 www.ti.com LAYOUT, GROUNDING, AND BYPASSING For best accuracy and minimum noise, the printed circuit board containing the DAC121C081 should have separate analog and digital areas. The areas are defined by the locations of the analog and digital power planes. Both of these planes should be located on the same board layer. There should be a single ground plane. A single ground plane is preferred if digital return current does not flow through the analog ground area. Frequently a single ground plane design will utilize a "fencing" technique to prevent the mixing of analog and digital ground current. Separate ground planes should only be utilized when the fencing technique is inadequate. The separate ground planes must be connected in one place, preferably near the DAC121C081. Special care is required to ensure that digital signals with fast edge rates do not pass over split ground planes. They must always have a continuous return path below their traces. The DAC121C081 power supply should be bypassed with a 4.7F and a 0.1F capacitor as close as possible to the device with the 0.1F right at the device supply pin. The 4.7F capacitor should be a tantalum type and the 0.1F capacitor should be a low ESL, low ESR type. The power supply for the DAC121C081 should only be used for analog circuits. Avoid crossover of analog and digital signals and keep the clock and data lines on the component side of the board. These clock and data lines should have controlled impedances. 24 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: DAC121C081 DAC121C085 DAC121C081, DAC121C085 www.ti.com SNAS395D - DECEMBER 2007 - REVISED MARCH 2013 REVISION HISTORY Changes from Revision C (March 2013) to Revision D * Page Changed layout of National Data Sheet to TI format .......................................................................................................... 24 Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: DAC121C081 DAC121C085 Submit Documentation Feedback 25 PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (C) Top-Side Markings (3) (4) DAC121C081CIMK/NOPB ACTIVE SOT DDC 6 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 X84C DAC121C081CIMKX/NOPB ACTIVE SOT DDC 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 X84C DAC121C081CISD ACTIVE WSON NGF 6 1000 TBD Call TI Call TI -40 to 125 X87 DAC121C081CISD/NOPB ACTIVE WSON NGF 6 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 X87 DAC121C081CISDX ACTIVE WSON NGF 6 4500 TBD Call TI Call TI -40 to 125 X87 DAC121C081CISDX/NOPB ACTIVE WSON NGF 6 4500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 X87 DAC121C085CIMM ACTIVE VSSOP DGK 8 1000 TBD Call TI Call TI -40 to 125 X90C DAC121C085CIMM/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 X90C DAC121C085CIMMX ACTIVE VSSOP DGK 8 3500 TBD Call TI Call TI -40 to 125 X90C DAC121C085CIMMX/NOPB ACTIVE VSSOP DGK 8 3500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 X90C (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com (3) 11-Apr-2013 MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 21-Mar-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device DAC121C081CIMK/NOPB Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant SOT DDC 6 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 SOT DDC 6 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 WSON NGF 6 1000 178.0 12.4 2.8 2.5 1.0 8.0 12.0 Q1 DAC121C081CISD/NOPB WSON NGF 6 1000 178.0 12.4 2.8 2.5 1.0 8.0 12.0 Q1 WSON NGF 6 4500 330.0 12.4 2.8 2.5 1.0 8.0 12.0 Q1 WSON NGF 6 4500 330.0 12.4 2.8 2.5 1.0 8.0 12.0 Q1 VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 VSSOP DGK 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 VSSOP DGK 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 DAC121C081CIMKX/NOP B DAC121C081CISD DAC121C081CISDX DAC121C081CISDX/NOP B DAC121C085CIMM DAC121C085CIMM/NOP B DAC121C085CIMMX DAC121C085CIMMX/NO PB Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 21-Mar-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) DAC121C081CIMK/NOPB SOT DDC 6 1000 210.0 185.0 35.0 SOT DDC 6 3000 210.0 185.0 35.0 DAC121C081CIMKX/NOP B DAC121C081CISD WSON NGF 6 1000 210.0 185.0 35.0 DAC121C081CISD/NOPB WSON NGF 6 1000 210.0 185.0 35.0 DAC121C081CISDX WSON NGF 6 4500 367.0 367.0 35.0 WSON NGF 6 4500 367.0 367.0 35.0 DAC121C085CIMM VSSOP DGK 8 1000 210.0 185.0 35.0 DAC121C085CIMM/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0 DAC121C085CIMMX VSSOP DGK 8 3500 367.0 367.0 35.0 VSSOP DGK 8 3500 367.0 367.0 35.0 DAC121C081CISDX/NOP B DAC121C085CIMMX/NOP B Pack Materials-Page 2 MECHANICAL DATA NGF0006A www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2013, Texas Instruments Incorporated