AFBR-2CAR01Z - AVAGO TECHNOLOGIES

AFBR-2CARxxZ

10G Ethernet SFP+ Active Optical Cable (AOC)

Data Sheet

Description

The Avago Technologies’ AFBR-2CARxxZ Active Opti-

cal Cable (AOC) is part of a family of SFP+ products to

serve 10Gb Ethernet (10GbE) applications. The letters

“xx” of the part number AFBR-2CARxxZ denoted the

cable length in meters. The AFBR-2CARxxZ AOC enables

10GbE equipment designs with very high port density

based on the new electrical and mechanical specica-

tion enhancements to the well known SFP specications

developed by the SFF Committee. The specications are

referred to as “SFP+” to represent the enhancements

over previous SFP specications. The SFP+ AOC have a

cable length up to 20m. These AOCs can be used as an

alternative solution to SFP+ passive and active copper

cables, while providing improved signal integrity, longer

distances, superior electromagnetic immunity and bet-

ter bit error rate performance.

Related Products

• The AFBR-703SDZ (AFBR-703ASDZ) is an SFP+ 10

Gigabit Ethernet 10GBASE-SR transceiver with case

temperature operated at 0-70 (0-85) °C for use on

multimode ber cables. It is best suited for OM3 high

bandwidth MMF link applications with link lengths up

to 300 meters.

• AFBR-707SDZ SFP+ 10 Gigabit Ethernet 10GBASE-

LRM transceiver for 220 meter operation in all MMF

link applications including OM1 and OM2 legacy ber

cables and new high bandwidth OM3 ber cables.

• The AFBR-704SDZ is an SFP+ transceiver for 10GbE

10GBASE-USR applications with case temperature

0-70 °C for use on multimode ber cables up to 100m.

• AFCT-5016Z SFP+ Evaluation Board The purpose of

this SFP+ evaluation board is to provide the designer

with a convenient means for evaluating SFP+ ber

optic transceivers.

Features

• Proven High Reliability 850 nm technology: Avago

VCSEL transmitter and Avago PIN receiver

• Maximum power dissipation 350mW per Active Cable

end

• Avago SFP+ package design enables equipment EMI

performance in high port density applications with

margin to Class B limits

Specications

• Electrical specications per SFF-8431 Specications

for Enhanced Small Form Factor Pluggable Module

SFP+

• 0 to 70 °C case temperature operating range

• Rx_LOS and Tx_DISABLE supported

• Mechanical specications per SFF Committee SFF

8432 Improved Pluggable Formfactor “IPF”

• Compliant to Restriction on Hazardous Substances

(RoHS) per EU and China requirements

• Class 1 eye safe per requirement of EN 60825-1 2007,

EN 60825-2 A2 2010

• 1E-15 BER performance

Applications

• 1/10 Gigabit Ethernet (1/10GbE)

• 1/2/4/8G Fibre Channel (1/2/4/8GFC), Fibre Channel

over Ethernet (FCoE)

• InniBand (QDR/DDR/SDR)

• Data Center Networking

- Converged Enhanced Ethernet Data Centers

- Data Center Bridging

• Networked storage systems

• High Performance Computing

• Proprietary Interconnects

Patent - www.avagotech.com/patents

Installation

The AFBR-2CARxxZ Active Optical Cable package is com-

pliant with the SFF-8432 Improved Pluggable Formfac-

tor housing specication for the SFP+. It can be installed

in any INF-8074 or SFF-8431/2 compliant Small Form

Pluggable (SFP) port regardless of host equipment op-

erating status The AFBR-2CARxxZ is hot-pluggable, al-

lowing both active cable ends to be installed while the

host system is operating and on-line. Upon insertion, the

housing makes initial contact with the host board SFP

cage, mitigating potential damage due to Electro-Static

Discharge (ESD).

Digital Interface and Serial Identication

The two-wire interface protocol and signaling detail are

based on SFF-8431. Conventional EEPROM memory,

bytes 0-255 at memory address 0xA0, is organized in

compliance with SFF-8431. The EEPROM contents of

AFBR-2CARxxZ are such that it can directly replace the

Active Copper Cable.

Transmitter Section

The transmitter section includes an 850 nm VCSEL (Verti-

cal Cavity Surface Emitting Laser) light source designed

and manufactured by Avago Technologies. The VCSEL is

driven by an IC which uses the incoming dierential high

speed logic signal to modulate the laser diode driver

current. This Tx laser driver circuit regulates the optical

power at a constant level provided the incoming data

pattern is DC balanced. DC blocking capacitors are lo-

cated inside the AOC package and are not required on

the system board.

Transmit Disable (TX_DISABLE)

Each end of the AFBR-2CARxxZ AOC has a TX_DISABLE

hardware pin, which accepts an input LVTTL compatible

control signal that shuts down the transmitter optical

output. A logic high signal implements the transmitter

disable function, while a low signal allows normal trans-

mitter operation. An internal pull up resistor disables

the transmitter until the host pulls the input low.

Receiver Section

The receiver section includes a PIN photodiode and cus-

tom amplication and quantization IC. DC blocking ca-

pacitors are located inside the AOC package and are not

required on the system board.

Receiver Loss of Signal (Rx_LOS)

The Rx portion of the IC includes detection circuitry

which monitors the average input Rx optical power and

provides a LVTTL/CMOS compatible status signal to the

host via the Rx_LOS pin. A logic high status on this Rx_

LOS output pin indicates a loss of signal, indicating a link

failure such as a broken ber, or the far-end cable-end is

not plugged in, or the far-end Tx has failed or has been

disabled.

Functional Data I/O

The AFBR-2CARxxZ interfaces with the host circuit board

through the twenty contact SFP+ electrical connector.

See Table 2 for contact descriptions. The device edge

connector is shown in Figure 2.

The AFBR-2CARxxZ high speed transmit and receive in-

terfaces require SFF-8431 compliant signal lines on the

host board. The TX_DISABLE and RX_LOS signals require

LVTTL signals on the host board (per SFF-8431) if used.

If an application does not take advantage of these func-

tions, care must be taken to ground TX_DISABLE to en-

able normal operation.

Part Number Description

AFBR-2CAR01Z 1 meter SFP+ Active Optical Cable

AFBR-2CAR02Z 2 meter SFP+ Active Optical Cable

AFBR-2CAR03Z 3 meter SFP+ Active Optical Cable

AFBR-2CAR05Z 5 meter SFP+ Active Optical Cable

AFBR-2CAR07Z 7 meter SFP+ Active Optical Cable

AFBR-2CAR10Z 10 meter SFP+ Active Optical Cable

AFBR-2CAR15Z 15 meter SFP+ Active Optical Cable

AFBR-2CAR20Z 20 meter SFP+ Active Optical Cable

AFCT-5016Z SFP+ Evaluation Board

Application Support

An Evaluation Kit and Reference Designs are available to

assist in evaluation of the AFBR-2CARxxZ. Please contact

your local Field Sales representative for availability and

ordering details.

Caution

There are no user serviceable parts nor maintenance

requirements for the AFBR-2CARxxZ. All mechanical

adjustments are made at the factory prior to shipment.

Tampering with, modifying, misusing or improperly han-

dling the AFBR-2CARxxZ will void the product warranty.

It may also result in improper operation and possibly

overstress the device. Performance degrada tion or de-

vice failure may result. Operating above maximum op-

erating conditions or in a manner inconsistent with it’s

design and function may result in exposure to hazardous

light radiation and may constitute an act of modifying or

manufacturing a laser product. Persons performing such

an act are required by law to recertify and re-identify the

laser product under the provisions of U.S. 21 CFR (Sub-

chapter J) and TUV.

Customer Manufacturing Processes

This AOC is pluggable and is not designed for aqueous

wash, IR reow, or wave soldering processes.

Ordering Information

Please contact your local eld sales engineer or one of

Avago Technologies franchised distributors for ordering

information. For technical information, please visit Ava-

go Technologies’ WEB page at www.avagotech.com. For

information related to SFF Committee documentation

visit www.scommittee.org.

Regulatory Compliance

The AFBR-2CARxxZ complies with all applicable laws

and regulations as detailed in Table 1. Certication level

is dependent on the overall conguration of the host

equipment. The AOC performance is oered as a gure

of merit to assist the designer.

Electrostatic Discharge (ESD)

The AFBR-2CARxxZ is compatible with ESD levels found

in typical manufacturing and operating environments as

described in Table 1. In the normal handling and opera-

tion of optical cables, ESD is of concern in two circum-

stances.

The rst case is during handling of the AOC prior to inser-

tion into an SFP+ compliant cage. To protect the device,

it’s important to use normal ESD handling pre-cautions.

These include use of grounded wrist straps, work-bench-

es and oor wherever a optical cable is handled.

The second case to consider is static discharges to the

exterior of the host equipment chassis after installation.

If the optical interface is exposed to the exterior of host

equipment cabinet, the optical cable may be subject to

system level ESD requirements.

Electromagnetic Interference (EMI)

Equipment incorporating 10 gigabit transceivers or ac-

tive optical cables is typically subject to regulation by the

FCC in the United States, CENELEC EN55022 (CISPR 22) in

Europe and VCCI in Japan. The AFBR-2CARxxZ enables

equipment compliance to these standards detailed in

Table 1. The metal housing and shielded design of the

AFBR-2CARxxZ minimizes the EMI challenge facing the

equipment designer. For superior EMI performance it

is recommended that equipment designs utilize SFP+

cages per SFF 8432.

RF Immunity (Susceptibility)

The EMI immunity of the AFBR-2CARxxZ exceeds typical

industry standards.

Eye Safety

The AFBR-2CARxxZ provides Class 1 (single fault toler-

ant) eye safety by design and has been tested for com-

pliance with the requirements listed in Table 1. The eye

safety circuit continuously monitors the optical output

power level and will disable the transmitter upon de-

tecting a condition beyond the scope of Class 1 certi-

cation. Such conditions can be due to inputs from the

host board (Vcc uctuation, unbalanced code) or a fault

within the transceiver. US CDRH and EU TUV certicates

are listed in table 1.

Flammability

The AFBR-2CARxxZ optical cable is made of metal and

high strength, heat resistant, chemical resistant and UL

94V-0 ame retardant plastic.

Table 1. Regulatory Compliance

Feature Test Method Performance

Electrostatic Discharge (ESD)

to the Electrical Contacts

MIL-STD-883C

Method 3015.4

Class 1 (> 2000 Volts)

Life Trac ESD Immunity IEC 61000-4-2 10 contacts of 8 kV on the electrical faceplate

with device inserted into a panel.

Life Trac ESD Immunity IEC 61000-4-2 Air discharge of 15 kV (min.) contact to con-

nector without damage.

Electromagnetic

Interference (EMI)

FCC Class B

CENELEC EN55022 Class B

(CISPR 22A)

VCCI Class A

System margins are dependent on customer

board and chassis design.

RF Immunity IEC 61000-4-3 Typically shows no measurable eect from a

10 V/m eld swept from 80MHz to 1 GHz

Laser Eye Safety and

Equipment Type Testing

EN 60825-1 2007, EN 60825-2 A2:2010 Pout: IEC AEL & US FDA CDRH Class 1

Component Recognition Underwriters Laboratories and Canadian Stan-

dards Association Joint Component Recogni-

tion for Information Technology Equipment

including Electrical Business Equipment

RoHS Compliance RoHS Directive 2002/95/EC and it’s amend-

ment directives 6/6

SGS Test Report No. LPC/13392 (AD-1)/07

CTS Ref. CTS/07/3283/Avago

Flammability Module: UL 94V-0

Cable: OFNR

BAUART

GEPRUFT

TYPE

APPROVED

TUV

Rheinland

Product Safety

Figure 1. Recommended power supply lter

4.7 µH

0.1 µF

VCC R

SFP+ AOC end

22 µF

VCC T

0.1 µF

3.3 V

HOST BOARD

0.1 µF

NOTE: INDUCTORS MUST HAVE LESS THAN 1Ω SERIES RESISTANCE TO LIMIT VOLTAGE DROP TO THE SFP MODULE.

22 µF

Table 2. Contact Description

Contact Symbol Function/Description Notes

1VeeT Transmitter Signal Ground Note 1

2 TX_FAULT Transmitter Fault (LVTTL-O) – Not used. Grounded inside the module Note 2

3 TX_DISABLE Transmitter Disable (LVTTL-I) – High or open disables the transmitter Note 3

4SDA Two Wire Serial Interface Data Line (LVCMOS – I/O)

(same as MOD-DEF2 in INF-8074)

Note 4

5 SCL Two Wire Serial Interface Clock Line (LVCMOS – I/O)

(same as MOD-DEF1 in INF-8074)

Note 4

6 MOD_ABS Module Absent (Output), connected to VeeT or VeeR in the module Note 5

7 RS0 Rate Select 0 - Not used, Presents high input impedance.

8 RX_LOS Receiver Loss of Signal (LVTTL-O) Note 2

9 RS1 Rate Select 1 - Not used, Presents high input impedance.

10 VeeR Receiver Signal Ground Note 1

11 VeeR Receiver Signal Ground Note 1

12 RD- Receiver Data Out Inverted (CML-O)

13 RD+ Receiver Data Out (CML-O)

14 VeeR Receiver Signal Ground

15 VccR Receiver Power + 3.3 V

16 VccT Transmitter Power + 3.3 V

17 VeeT Transmitter Signal Ground Note 1

18 TD+ Transmitter Data In (CML-I)

19 TD- Transmitter Data In Inverted (CML-I)

20 VeeT Transmitter Signal Ground Note 1

Notes:

1. The module signal grounds are isolated from the module case.

2. This is an open collector/drain output that on the host board requires a 4.7 kΩ to 10 kΩ pullup resistor to VccHost. See Figure 2.

3. This input is internally biased high with a 4.7 kΩ to 10 kΩ pullup resistor to VccT.

4. Two-Wire Serial interface clock and data lines require an external pullup resistor dependent on the capacitance load.

5. This is a ground return that on the host board requires a 4.7 kΩ to 10 kΩ pullup resistor to VccHost.

Figure 2. Module edge connector contacts

TOP VIEW

OF BOARD

TOWARD

HOST

BOTTOM OF

BOARD AS

VIEWED FROM

TOP THROUGH

BOARD

Table 3. Absolute Maximum Ratings

Stress in excess of any of the individual Absolute Maximum Ratings can cause immediate catastrophic damage to the module

even if all other parameters are within Recommended Operating Conditions. It should not be assumed that limiting values of

more than one parameter can be applied concurrently. Exposure to any of the Absolute Maximum Ratings for extended periods

can adversely aect reliability.

Parameter Symbol Minimum Maximum Unit Notes

Storage Temperature TS-40 85 C

Relative Humidity RH 5 95 %

Supply Voltage VccT, VccR -0.3 3.8 V Note 1

Low Speed Input Voltage -0.5 Vcc+0.5 V

Two-Wire Interface Input Voltage -0.5 Vcc+0.5 V

High Speed Input Voltage, Single Ended -0.3 Vcc+0.5 V

High Speed Input Voltage, Dierential 2.5 V

Low Speed Output Current -20 20 mA

Table 4. Recommended Operating Conditions

Recommended Operating Conditions specify parameters for which the electrical and optical characteristics hold unless other-

wise noted. Optical and electrical charactristics are not dened for operation outside the Recommended Operating Conditions,

reliability is not implied and damage to the module may occur for such operation over an extended period of time.

Parameter Symbol Minimum Maximum Unit Notes

Case Operating Temperature TC0 70 °C Note 2

Module Supply Voltage VccT, VccR 3.135 3.465 V Figure 3

Host Supply Voltage VccHost 3.14 3.46 V

Signal Rate 1-10.3125 GBd -100 100 ppm

Power Supply Noise Tolerance 66 10Hz to 10MHz Figure 3

Tx Input Single Ended DC

Voltage Tolerance (Ref VeeT)

V -0.3 4.0 V

Rx Output Single Ended Voltage Tolerance V -0.3 4.0 V

Bend Radius 30 mm

Table 5. Low Speed Signal Electrical Characteristics

The following characteristics are dened over the Recommended Operating Conditions unless otherwise noted. Typical values

are for Tc = 40°C. VccT and VccR = 3.3 V.

Parameter Symbol Minimum Typical Maximum Unit Notes

Module Supply Current ICC 83 107 mA Note 3

Power Dissipation PDISS 275 350 mW Note 4

TX_FAULT, RX_LOS IOH - 50 + 37.5 mANote 5

VOL - 0.3 0.4 V

TX_DISABLE VIH 2.0 VccT + 0.3 V Note 6

VIL -0.3 0.8 V

Notes:

1. The module supply voltages, VccT and VccR must not dier by more than 0.5 V or damage to the device may occur.

2. Ambient operating temperature limits are based on the Case Operating Temperature limits and are subject to the host system thermal design.

3. Supply current includes both VccT and VccR connections.

4. Per port

5. Measured with a 4.7 k Ω load to VccHost.

6. TX_DISABLE has an internal 4.7 kΩ to 10 kΩ pull-up to VccT

Table 6. High Speed Signal Electrical Characteristics

The following characteristics are dened over the Recommended Operating Conditions unless otherwise noted. Typi-

cal values are for Tc = 40°C. VccT and VccR = 3.3 V.

Parameter Symbol Minimum Typical Maximum Unit Notes

Tx Input Dierential Voltage (TD +/-) VI180 700 mV Note 1;

see Figure 3b

Tx Input Mask See Figure 3b

Tx Input AC Common Mode Voltage Tolerance 15 mV (RMS)

Tx Input Dierential S-parameter (100 Ω Ref.) SDD11 Note 3

Tx Input Dierential to Common

Mode Conversion (25 Ω Ref.)

SCD11 -10 dB 0.01-11.1 GHz

Rx Output Dierential Voltage (RD +/-) Vo 300 850 mV Note 2

Rx Output Termination Mismatch @ 1MHz DZm5 %

Rx Output AC Common Mode Voltage 7.5 mV (RMS) Note 5

Rx Output Output Rise and Fall Time

(20% to 80%)

tr, tf 28 ps

Rx Output Total Jitter TJ 0.70 Ulp-p Note 7

Rx Output Deterministic Jitter DJ 0.42 Ulp-p

Rx Output Dierential S-parameter SDD22 Note 4

Rx Output Common Mode Reection

Coecient (25 Ω Ref.)

SCC22 Note 6

-3

0.01-2.5 GHz

2.5-11.1 GHz

Receiver Output Eye Mask See Figure 3b

Notes:

1. Internally AC coupled and terminated (100 Ohm dierential).

2. Internally AC coupled but requires an external load termination (100 Ohm dierential).

3. Maximum reection coecient is expressed as SDD11=Max(-12+2*sqrt(f ) , -6.3+13*log10(f/5.5)), for f in GHz.

4. Maximum reection coecient is expressed as SDD22=Max(-12+2*sqrt(f ) , -6.3+13*log10(f/5.5)), for f in GHz.

5. The RMS value is measured by calculating the standard deviation of the histogram for one UI of the common mode signal.

6. Maximum reection coecient given by equation SCC22(dB) < -7 + 1.6 × f, with f in GHz.

7. TJ measured at 1e-12

Figure 3a. Receiver Electrical Optical Eye Mask Denition Figure 3b. Transmitter Dierential Input Compliance Mask at B

150

-150

-425

00.35 1.00.65

ABSOLUTE AMPLITUDE - mV

NORMALIZED TIME (UNIT INTERVAL)

425

-350

-95

350

0.0 0.12 0.33 0.67 0.88 1.0

NORMALIZED TIME (UNIT INTERVAL)

VOLTAGE - mV

Table 7. Two-Wire Interface Electrical Characteristics

Parameter Symbol Minimum Maximum Unit Conditions

Host Vcc Range VccHTWI 3.135 3.465 V

SCL and SDA VOL 0.0 0.40 V Rp[1] pulled to VccHTWI,

measured at host side of

connector

VOH VccHTWI - 0.5 VccHTWI + 0.3 V

SCL and SDA VIL -0.3 VccT*0.3 V

VIH VccT*0.7 VccT + 0.5 V

Input Current on the

SCL and SDA Contacts

Il-10 10 µA

Capacitance on SCL

and SDA Contacts

Ci[2] 14 pF

Total bus capacitance

for SCL and for SDA

Cb[3] 100 pF At 400 kHz, 3.0 kΩ Rp, max

At 100 kHz, 8.0 kΩ Rp, max

290 pF At 400 kHz, 1.1 kΩRp, max

At 100 kHz, 2.75 kΩ Rp, max

Notes:

1. Rp is the pull up resistor. Active bus termination may be used by the host in place of a pullup resistor. Pull ups can be connected to various

power supplies, however the host board design shall ensure that no module contact has voltage exceeding VccT or VccR by 0.5 V nor requires

the module to sink more than 3.0 mA current.

2. Ci is the capacitance looking into the module SCL and SDA contacts

3. Cb is the total bus capacitance on the SCL or SDA bus.

Table 8. Control Functions: Low Speed Signals Timing Characteristics

Parameter Symbol Maximum Units Notes

Time to Initialize t_inti 300 ms Note 1

TX_DISABLE Assert + RX_LOS Assert Time t_los_on 110 us Note 2

TX_DISABLE Negate + RX_LOS Deassert Time t_los_o 2.1 ms Note 3

Notes:

1. Time from power on or falling edge of TX_DISABLE to when the modulated optical output rises above 90% of nominal (not measurable in the

Active Optical Cable) and the Two-Wire interface is available.

2. The maximum time between (a) when the near-end AOC-end has TX_DISABLE asserted until (b) RX_LOS is declared/asserted on the far-end

AOC-end. There is also a small delay for the signal transit time through the optical cable, however, this is a small eect: light propagating

through ber ~ 5ns per meter. A 10 ms interval between assertions of TX_DISABLE is required.

3. The maximum time between (a) when the near-end AOC-end has TX_DISABLE negated until (b) RX_LOS is deasserted on the far-end AOC-end.

There is also a small delay for the signal to transit time through the optical cable, however, this is a small eect: light propagating through ber

~ 5 ns per meter

Table 9. EEPROM Serial ID Memory Contents – Address A0h

Page A0h only, per SFF-8472 Revision 11.0

Byte #

Decimal

Byte #

Hex

Default Value

(Hex) Notes Type

0 0 03 Physical Device SFP/SFP+ = “03h” Read-Only

1 1 04 Two Wire Serial Interface Function = “04h” Read-Only

2 2 21 Copper pigtail Read-Only

3 3 00 Not Applicable Read-Only

4 4 00 Not Applicable Read-Only

5 5 00 Not Applicable Read-Only

6 6 00 Not Applicable Read-Only

7 7 00 Unspecied Read-Only

8 8 08 Active cable Read-Only

9 9 00 Unspecied Read-Only

10 A 00 Unspecied Read-Only

11 B 00 Unspecied Read-Only

12 C 67 10312.5 MB/s nominal rate = “67h” Read-Only

13 D 00 Rate Select not implemented Read-Only

14 E 00 Not Applicable Read-Only

15 F 00 Not Applicable Read-Only

16 10 00 Not Applicable Read-Only

17 11 00 Not Applicable Read-Only

18 12 Link length cable, units of meters (decimal) Read-Only

19 13 00 Not Applicable Read-Only

20 14 41 “A” - Vendor Name ASCII character Read-Only

21 15 56 “V” - Vendor Name ASCII character Read-Only

22 16 41 “A” - Vendor Name ASCII character Read-Only

23 17 47 “G” - Vendor Name ASCII character Read-Only

24 18 4F “O” - Vendor Name ASCII character Read-Only

25 19 20 “ “- Vendor Name ASCII character Read-Only

26 1A 20 “ “- Vendor Name ASCII character Read-Only

27 1B 20 “ “- Vendor Name ASCII character Read-Only

28 1C 20 “ “- Vendor Name ASCII character Read-Only

29 1D 20 “ “- Vendor Name ASCII character Read-Only

30 1E 20 “ “- Vendor Name ASCII character Read-Only

31 1F 20 “ “- Vendor Name ASCII character Read-Only

32 20 20 “ “- Vendor Name ASCII character Read-Only

33 21 20 “ “- Vendor Name ASCII character Read-Only

34 22 20 “ “- Vendor Name ASCII character Read-Only

35 23 20 “ “- Vendor Name ASCII character Read-Only

36 24 00 Not Used Read-Only

37 25 00 Hex Byte of Vendor OUI[1] Read-Only

38 26 17 Hex Byte of Vendor OUI[1] Read-Only

39 27 6A Hex Byte of Vendor OUI[1] Read-Only

Table 9. EEPROM Serial ID Memory Contents – Address A0h (Cont.)

Byte #

Decimal

Byte #

Hex

Default Value

(Hex) Notes Type

40 28 41 “A” - Vendor Part Number ASCII character Read-Only

41 29 46 “F” - Vendor Part Number ASCII character Read-Only

42 2A 42 “B” - Vendor Part Number ASCII character Read-Only

43 2B 52 “R” - Vendor Part Number ASCII character Read-Only

44 2C 2D “-“ - Vendor Part Number ASCII character Read-Only

45 2D 32 “2” - Vendor Part Number ASCII character Read-Only

46 2E 43 “C” - Vendor Part Number ASCII character Read-Only

47 2F 41 “A” - Vendor Part Number ASCII character Read-Only

48 30 52 “R” - Vendor Part Number ASCII character Read-Only

49 31 x Cable Length in meters - Vendor Part Number ASCII character Read-Only

50 32 x Cable Length in meters - Vendor Part Number ASCII character Read-Only

51 33 5A “Z” - Vendor Revision Number ASCII character Read-Only

52 34 20 “ ” - Vendor Part Number ASCII character Read-Only

53 35 20 “ ” - Vendor Part Number ASCII character Read-Only

54 36 20 “ ” - Vendor Part Number ASCII character Read-Only

55 37 20 “ ” - Vendor Part Number ASCII character Read-Only

56 38 20 “ ” - Vendor Revision Number ASCII character Read-Only

57 39 20 “ ” - Vendor Revision Number ASCII character Read-Only

58 3A 20 “ ” - Vendor Revision Number ASCII character Read-Only

59 3B 20 “ ” - Vendor Revision Number ASCII character Read-Only

60 3C 04 Compliant to SFF-8431 Limiting = “04h” Read-Only

61 3D 00 Not Applicable Read-Only

62 3E 00 Not Used Read-Only

63 3F Checksum (Hex LSB Only) Bytes 0-62[2] Read-Only

64 40 00 Uncooled Laser. Power Level 1 operation (1.0 Watt max). Limiting

receiver output. = “00h”

Read-Only

65 41 12 Tx_Disable implemented & SFP Rx_LOS implemented = “12h” Read-Only

66 42 00 Not Specied Read-Only

67 43 00 Not Specied Read-Only

68-83 44-53 Vendor Serial Number ASCII characters[3] Read-Only

84-91 54-5B Vendor Date Code ASCII characters[4] Read-Only

92 5C 00 No Diagnostics = “00h” Read-Only

93 5D 00 No Enhanced Options = “00h” Read-Only

94 5E 00 Unspecied Read-Only

95 5F Checksum (Hex LSB Only) Bytes 64-94[2] Read-Only

96-255 60-FF 00 VENDOR SPECIFIC ID FIELDS Read-Only

Notes:

1. The IEEE Organizationally Unique Identier (OUI) assigned to Avago Technologies is 00-17-6A (3 bytes hex).

2. Addresses 63 and 95 are checksums calculated (per SFF-8472) and stored prior to product shipment.

3. Addresses 68-83 specify the AFBR-2CARxxZ ASCII serial number and will vary on a per unit basis.

4. Addresses 84-91 specify the AFBR-2CARxxZ ASCII date code and will vary on a per date code basis.

Figure 4. Module drawing

Measurement Minimum Maximum Units Comments

Insertion 0 18 N

Extraction 0 12.5 N

Retention 90 170 N No functional damage to device below 90N

Front-1

Top-1

Bottom-1

65 30

2.55±0.1 1.4±0.1

51 8.6±0.1

2±0.1

COLOR TAGLABEL

Right-1

15.2 Uncompressed T_CASE REFERENCE POINT

For product information and a complete list of distributors, please go to our website: www.avagotech.com

Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.

AV02-4397EN - March 21, 2014

Table 11. Optical Fiber Specications

Parameter Specication

Tight buer color orange, yellow

Tight buer material PVC

Tight buer diameter mm 0.60 ± 0.05

Fiber type 62.5/125 (OFS)

Bandwith:160 MHz.km @ 850 nm

Strength member Aramid yarns

Jacket color Orange

Jacket material PVC

Cable diameter mm 3.0 ± 0.1

Cable weight Kg/km 7.0

Min. bending radius mm 30

Attenuation dB/km ≤ 3.5 at 850 nm

≤1.5 at 1300 nm

Short tension N 120

Short crush N/100mm 500

Operation temperature °C-20~70

Figure 6. Optical ber details

Optical ber

Tight layer

Aramid yarns

Jacket

78.7

R30

∅3

13.8 13.65

Figure 5. Bend Radius Denition

Length Cable Length Tolerance

1 m +20/-0 cm

2 m +20/-0 cm

3 m +20/-0 cm

5 m +20/-0 cm

7 m +20/-0 cm

10 m +20/-0 cm

15 m +2%/-0 cm

20 m +2%/-0 cm

Note:

Cable Length is dened as the length of the ber only

(not including the SFP+ module-ends).

Table 10. SFP+ AOC Cable Assembly Length Tolerances