NFS110-7601PJ - Artesyn Embedded Technologies

313

process

yellow

3405

1797

1375

116

2607

652

242

2985

375

240

Embedded Power for

Business-Critical Continuity

NFS110 Series

Single & Quad output

Special Features

• 7.0 x 4.25 x 1.8 inch package

• Overvoltage and short circuit

protection

• 110 W with 20 CFM

• Adjustable outputs

• EN55022, EN55011 conducted

emissions level B

• UL, VDE and CSA safety

approvals

• CE mark

• Available RoHS compliant

• 2 year warranty

Total Power: 80 - 110 W

Input Voltage: 85 - 264 Vac

120 - 370 Vdc

# of Outputs: Single, quad

Safety

• VDE0805/EN60950/

• IEC950/IEC1010

File No. 10401-3336-0213

• Licence No. 4001467 7

• UL1950 File No. E132002

• CSA C22.2 No. 950

File No. LR41062C

Rev. 11.2.09_69

NFS110 Series

1 of 5

Electrical Specications

All specications are typical at nominal input, full load at 25 °C unless otherwise stated

Output

Voltage adjustability: +5.1 V o/p on multi’s

5.1 V single output

12 V single output

15 V single output

24 V single output

3.0%

12 - 14 V

15 - 18 V

24 - 30 V

Line regulation: LL to HL, FL

All outputs on all units

±0.1% max.

Overshoot/undershoot: At turn-on 0%

Temperature coefcient: All outputs ±0.02%/°C

Overvoltage protection: Multi o/p 5.1 V only

5.1 V single output

12 V single output

15 V single output

24 V single output

6.25 V ± 0.75 V

15.75 V ± 1.0 V

22 V ± 1.5 V

33 V ± 2.5 V

Output power limit: Primary power limited Pin max. 160 W

Pout min. 110 W

Minimum output current: (See Note 13) 0 A

Short circuit protection: Burst mode operation

Input

Input voltage range: 85 - 264 Vac

120 - 370 Vdc

Input frequency range: 47 - 440 Hz

Input surge current: 230 Vac 35 A

Safety ground leakage current: 110 Vac, 50 Hz

230 Vac, 50 Hz

0.2 mA, max.

0.4 mA, max.

Rev. 11.2.09_69

NFS110 Series

2 of 5

Embedded Power for

Business-Critical Continuity

313

process

yellow

3405

1797

1375

116

2607

652

242

2985

375

240

Environmental Specications

Thermal performance: Operating ambient 0° C to +70 °C

(See notes 9, 10) Non-operating -40 °C to +85 °C

0 °C to 50 °C convection cooled 80 W

+50 °C to +70 °C, convection cooled Derate 2 W/°C

0 °C to +50 °C, 20 CFM forced air 110 W

+50 °C to +70 °C, 20CFM forced air Derate 2.75 W/°C

Peak, 0 °C to +50 °C, max. 60 seconds 110W

Relative humidity: Non-condensing 5 to 95% RH

Altitude: Operating 10,000 feet max.

Non-operating 40,000 feet max.

Vibration:

(See Note 11)

5 - 500 Hz 2.4 G rms peak

EMC Characteristics

Conducted emissions: EN55022, FCC part 15 Level B

Radiated emissions: EN55022, FCC part 15 Level A

ESD air: EN61000-4-2, level 3 Perf. criteria 1

ESD contact: EN61000-4-2, level 4 Perf. criteria 1

Surge: EN61000-4-3, level 3 Perf. criteria 1

Fast transients: EN61000-4-4, level 3 Perf. criteria 1

Radiated immunity: EN61000-4-5, level 3 Perf. criteria 2

Conducted immunity: EN61000-4-6, level 3 Perf. criteria 1

General Specications

Hold-up time: 110 Vac @ 80 W

110 Vac @ 110 W

230 Vac @ 80 W

230 Vac @ 100 W

35 ms

17 ms

140 ms

100 ms

Efciency: Multiple outputs

+5.1 V single

12 V and 15 V singles

24 V single

70% typical

72% typical

75% typical

Isolation voltage: Input/output

Input/chassis

3000 Vac

1500 Vac

Approvals and standards:

(see note 12)

VDE0805, EN60950, IEC950, IEC1010, UL1950, CSA C22.2 No. 950

Weight: Singles

Multiple outputs

550 g (19.4 oz)

600 g (21.2 oz)

MTBF (@25 ºC): MIL-HDBK-217E 125,000 hours min.

Rev. 11.2.09_69

NFS110 Series

3 of 5

Embedded Power for

Business-Critical Continuity

313

process

yellow

3405

1797

1375

116

2607

652

242

2985

375

240

Notes

1 Convection cooled, 80 W maximum.

2 Peak outputs lasting less than 60 seconds with duty cycle less than 10%. Total

peak power must not exceed 110 W.

3 Forced air, 20 CFM at 1 atmosphere, 110 W maximum.

4 Figure is peak-to-peak. Output ripple is measured across a 50 MHz bandwidth

using a 12 inch twisted pair terminated with a 47 µF capacitor.

5 Total regulation is dened as the static output regulation at 25 °C, including

initial tolerance, line voltage within stated limits and output voltages adjusted

to their factory settings.

6 To achieve stated regulation on the 24 V output on the NFS110-7602PJ, the

following load condition must be true: IA / IB ≤ 5, where:

IA = +5.1 V output current, and

IB = +24 V output current

The +24 V output will maintain ±5.0% regulation under the following

additional condition: IA ≤ 5 A.

7 Single output models have oating outputs which may be referenced as

either positive or negative. Higher voltage supplies may be adjusted over a

wide output voltage range, as long as the total output power does not exceed

80 Watts (natural convection) or 110 Watts (forced air).

8 Power fail detect not available on single output models.

9 Derating curve is application specic for ambient temperatures >50 °C,

for optimum reliability no part of the heatsink should exceed 90 ºC and no

semiconductor case temperature should exceed 100 ºC.

10 Caution: Allow a minimum of 1 second after disconnecting the power when

making thermal measurements.

11 Three orthogonal axes, random vibration, 10 minute test for each axis.

12 This product is only for inclusion by professional installers within other

equipment and must not be operated as a stand alone product.

13 Recommend a minimum load of 11 W to achieve the design MTBF. See the

derating curve on page 4.

14 Power failure detec is optional by including the sufx “P” to the model

number.

15 The ‘J’ sufx indicates that these parts are Pb-free (RoHS 6/6) compliant.

16 NOTICE: Some models do not support all options. Please contact your

local Emerson Network Power representative or use the on-line model

number search tool at http://www.PowerConversion.com to nd a suitable

alternative.

Ordering Information

Output

Voltage

Output Currents Ripple (4) Total

Regulation (5) Model Numbers (13, 15, F)

Max (1) Peak (2) Fan (3)

+5.1 V 8 A 20 A 10 A 50 mV ± 2.0% NFS110-7601PJ (14)

+12 V 4.5 A 9 A 5 A 120 mV ± 3.0%

–12 V 0.5 A 1.5 A 1 A 120 mV ± 3.0%

–5 V 0.5 A 1.5 A 1 A 50 mV ± 3.0%

+5.1 V (IA) 8 A 20 A 10 A 50 mV ± 2.0% NFS110-7602PJ (6, 14)

+24 V (IB) (6) 3.5 A 4.5 A 4.5 A 240 mV +10/–5.0%

+12 V 4.5 A 9 A 5 A 120 mV ± 3.0%

–12 V 0.5 A 1.5 A 1 A 120 mV ± 3.0%

+5.1 V 8 A 20 A 10 A 50 mV ± 2.0% NFS110-7604PJ (14)

15 V 4 A 7.5 A 5 A 150 mV ± 4.0%

-15 V 0.5 A 1.5 A 1 A 150 mV ± 3.0%

-5 V 0.5 A 1.5 A 1 A 50 mV ± 3.0%

12 V 7 A 9 A 9 A 120 mV ± 2.0% NFS110-7612J (7,8)

15 V 5 A 7.3 A 7.3 A 150 mV ± 2.0% NFS110-7615J (7,8)

24 V 3.5 A 4.5 A 4.5 A 240 mV ± 2.0% NFS110-7624J (7,8)

Transient Response

NFS110-7601PJ +5.1 V (7.5 A to 10 A)

+12 V (2.5 A to 5 A)

-12 V (0.5 A to 1 A)

-5 V (0.5 A to 1 A)

150 mV peak, 1 ms recovery

100 mV peak, 0.5 ms recovery

NFS110-7602PJ +5.1 V (7.5 A to 10 A)

+24 V (1.5 A to 3 A)

+12 V (2.5 A to 5 A)

-12 V (0.5 A to 1 A)

150 mV peak, 1 ms recovery

300 mV peak, 1 ms recovery

100 mV peak, 0.5 ms recovery

NFS110-7604PJ +5.1 V (7.5 A to 10 A)

+15 V (2.5 A to 5 A)

-15 V (0.5 A to 1 A)

-5 V (0.5 A to 1 A)

150 mV peak, 1 ms recovery

100 mV peak, 0.5 ms recovery

NFS110-7605J +5.1 V (10 A to 20 A) 250 mV peak, 1 ms recovery

NFS110-7612J: +12 V (4.5 A to 9 A) 360 mV peak, 1 ms recovery

NFS110-7615J +15 V (3.65 A to 7.3 A) 450 mV peak, 1 ms recovery

NFS110-7624J +24 V (2.25 A to 4.5 A) 720 mV peak, 1 ms recovery

ALL DIMENSIONS IN INCHES (mm)

Optional

Power Fail

Detect Circuit

(Key = Pin 2)

Pin 1

6-32 UNC

(4PL)

PIN 1

1.00 0.005

(25.4)

Voltage Adjust

PIN 1

0.156

DIA. HOLE

(4PL)

5A, 250 VAC

0.475

0.010

(12.07)

1.55 0.005

(39.37)

3.35 0.015 (85.09)

1.80 (45.72) MAX

0.050 0.020

(1.27)

4.250

0.020

(107.95)

3.750

0.005

(95.25)

0.250

0.010

(6.35)

0.250

0.010

(6.35)

6.50 0.005 (165.1)

7.00 0.020 (177.8)

Rev. 11.2.09_69

NFS110 Series

4 of 5

Embedded Power for

Business-Critical Continuity

313

process

yellow

3405

1797

1375

116

2607

652

242

2985

375

240

AC (J1) mating connector

Molex 09-50-3051 or Molex 09-91-0500 mating connector with 2478

or equivalent crimp terminals.

DC (J2) mating connector

Molex 09-50-3131 or Molex 09-91-1300 mating connector with 2478

or equivalent crimp terminals.

Power fail detect signal (Note 8)

50ms ≤ T1 ≤ 200ms

T2 will vary with line and load

T3 ≥ 3ms

Pout: 110W

PFD output is an open collector which

will sink ≤ 40mA in the low state.

HIGH

T1 T2

4.75V

3.5V MIN

0-0.4 MAX

LOW

4.75V

5V OUTPUT

PFD SIGNAL

AC INPUT

OPTIONAL POWER FAIL DETECT TIMING DIAGRAM

80W

20 CFM FORCED AIR COOLING

40W

55W

11W 11W MINIMUM LOAD REQUIRED AT 230VAC

NATURAL

CONVECTION

COOLING

0C 10C 20C 30C 40C 50C 60C 70C

DERATING CURVE (See Notes 9, 10)

Output Power (Watts)

110W

Pin Connections

J1 -7601PJ -7602 P -7604PJ Singles

Pin 1 AC Ground AC Ground AC Ground AC Ground

Pin 2 AC Neutral AC Neutral AC Neutral AC Neutral

Pin 3 AC Line AC Line AC Line AC Line

Pin 1 +5.1 V +5.1 V +5.1 V Vout

Pin 2 +5.1 V +5.1 V +5.1 V Vout

Pin 3 +5.1 V +5.1 V +5.1 V Vout

Pin 4 Return Return Return Return

Pin 5 Return Return Return Return

Pin 6 Return Return Return Return

Pin 7 Return Return Return Return

Pin 8 +12 V +12 V +15 V Vout

Pin 9 +12 V +12 V +15 V Vout

Pin 10 PFD PFD PFD N/C

Pin 11 -12 V -12 V -15 V N/C

Pin 12 Removed for Key

Pin 13 -5 V +24 V -5 V N/C

N/C = no connection

Mechanical Notes:

A Metallic or non-metallic stand-offs (maximum diameter 5.4mm) can be used in all four mounting holes

without effecting safety approval.

B The ground pad of the mounting hole near J1, allows system grounding through a metal stand-off to

the system chassis.

C The heat sink is grounded, and allows system grounding by mechanical connection to the system

chassis.

D The supply must be mechanically supported using the PCB mounting holes and may be additionally

supported by the heatsink mounting holes.

E It is always advisable to attach the power supply heat sink to another thermal dissipator (such as a

chassis or nned heatsink etc). The resulting decrease in heat sink mounted component temperatures

will improve power supply lifetime.

F A standard L-bracket and cover is available for mounting which contains all screws, connectors and

necessary mounting hardware. The kit is available, order part number “NFS110CJ” .

313

process

yellow

3405

1797

1375

116

2607

652

242

2985

375

240

Embedded Power for

Business-Critical Continuity

Rev. 11.2.09_69

NFS110 Series

5 of 5

Americas

5810 Van Allen Way

Carlsbad, CA 92008

USA

Telephone: +1 760 930 4600

Facsimile: +1 760 930 0698

Europe (UK)

Waterfront Business Park

Merry Hill, Dudley

West Midlands, DY5 1LX

United Kingdom

Telephone: +44 (0) 1384 842 211

Facsimile: +44 (0) 1384 843 355

Asia (HK)

14/F, Lu Plaza

2 Wing Yip Street

Kwun Tong, Kowloon

Hong Kong

Telephone: +852 2176 3333

Facsimile: +852 2176 3888

For global contact, visit:

www.PowerConversion.com

techsupport.embeddedpower

@emerson.com

While every precaution has been taken to ensure

accuracy and completeness in this literature, Emerson

Network Power assumes no responsibility, and disclaims

all liability for damages resulting from use of this

information or for any errors or omissions.

Emerson Network Power and the Emerson

Network Power logo are trademarks and

service marks of Emerson Electric Co.

EmersonNetworkPower.com

Embedded Computing

Embedded Power

Monitoring

Outside Plant

Power Switching & Controls

Precision Cooling

Racks & Integrated Cabinets

Services

Surge Protection

Emerson Network Power.

The global leader in enabling

business-critical continuity.

AC Power

Connectivity

DC Power

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Artesyn Embedded Technologies:

NFS110CJ NFS110-7601PJ NFS110-7602PJ