SN55107A, SN75107A, SN75107B, SN75108A DUAL LINE RECEIVERS SLLS069D - JANUARY 1977 - REVISED APRIL 1998 D D D D D D High Speed Standard Supply Voltage Dual Channels High Common-Mode Rejection Ratio High Input Impedance High Input Sensitivity Differential Common-Mode Input Voltage Range of 3 V Strobe Inputs for Receiver Selection Gate Inputs for Logic Versatility TTL Drive Capability High dc Noise Margin Totem-Pole Outputs B Version Has Diode-Protected Input for Power-Off Condition SN55107A . . . J OR W PACKAGE SN75107A, SN75107B, SN75108A . . . D OR N PACKAGE (TOP VIEW) 1A 1B NC 1Y 1G S GND 1 14 2 13 3 12 4 11 5 10 6 9 7 8 VCC + VCC - 2A 2B NC 2Y 2G SN55107A . . . FK PACKAGE (TOP VIEW) 1B 1A NC VCC + VCC - D D D D D D D description NC NC 1Y NC 1G 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 2A NC 2B NC NC S GND NC 2G 2Y These circuits are TTL-compatible, high-speed line receivers. Each is a monolithic dual circuit featuring two independent channels. They are designed for general use, as well as for such specific applications as data comparators and balanced, unbalanced, and party-line transmission systems. These devices are unilaterally interchangeable with and are replacements for the SN55107, SN75107, and SN75108, but offer diode-clamped strobe inputs to simplify circuit design. 4 NC - No internal connection The essential difference between the A and B versions can be seen in the schematics. Input-protection diodes are in series with the collectors of the differential-input transistors of the B versions. These diodes are useful in certain party-line systems that have multiple VCC + power supplies and can be operated with some of the VCC + supplies turned off. In such a system, if a supply is turned off and allowed to go to ground, the equivalent input circuit connected to that supply would be as follows: Input Input A Version B Version This would be a problem in specific systems that might have the transmission lines biased to some potential greater than 1.4 V. The SN55107A is characterized for operation over the full military temperature range of - 55C to 125C. The SN75107A, SN75107B, and SN75108A are characterized for operation from 0C to 70C. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 1998, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 SN55107A, SN75107A, SN75107B, SN75108A DUAL LINE RECEIVERS SLLS069D - JANUARY 1977 - REVISED APRIL 1998 FUNCTION TABLE DIFFERENTIAL INPUTS A-B VID 25 mV - 25 mV < VID < 25 mV VID - 25 mV STROBES G S OUTPUT Y X X H X L H L X H H H Indeterminate X L H L X H H H L H = high level, L = low level, X = irrelevant logic symbol SN55107A, SN75107A, and SN75107B S 1A 1B 1G 2A 2B 2G 6 1 S EN & 4 2 1A 1Y 1B 5 1G 12 2A 9 11 8 2Y 2B 2G SN75108A 6 EN & 1 2 12 11 9 8 logic diagram (positive logic) 1A 1B 1G 2G 2A 2B 2 6 1 2 4 5 1Y 8 12 11 POST OFFICE BOX 655303 1Y 5 These symbols are in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. Pin numbers shown are for the D, J, N, and W packages. S 4 9 2Y * DALLAS, TEXAS 75265 2Y SN55107A, SN75107A, SN75107B, SN75108A DUAL LINE RECEIVERS SLLS069D - JANUARY 1977 - REVISED APRIL 1998 schematic (each receiver) VCC + See Note 2 14 1 k 400 4 k 1.6 k 1 k See Note 2 120 4.8 k 800 4, 9 A 1, 12 760 R 7 Inputs B Output Y GND 2, 11 5, 8 Strobe G 4.25 k 3 k VCC - 3 k Common to Both Receivers 13 6 Strobe S To Other Receiver Pin numbers shown are for D, J, N, and W packages. R = 1 k for '107A and SN75107B, 750 for SN75108A. NOTES: 1. Resistor values shown are nominal. 2. Components shown with dashed lines in the output circuitry are applicable to the '107A and SN75107B only. Diodes in series with the collectors of the differential input transistors are short circuited on '107A and SN75108A. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 3 SN55107A, SN75107A, SN75107B, SN75108A DUAL LINE RECEIVERS SLLS069D - JANUARY 1977 - REVISED APRIL 1998 absolute maximum ratings over operating free-air temperature (unless otherwise noted) Supply voltage, VCC + (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Supply voltage, VCC - . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 7 V Differential input voltage, VID (see Note 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 V Common-mode input voltage, VIC (see Note 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 V Strobe input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V Continuous total dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65C to 150C Case temperature for 60 seconds, Tc: FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260C Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: J package . . . . . . . . . . . . . . . . . . . . . 300C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D, N, or W package . . . . . . . . . . . . . 260C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 3. All voltage values, except differential voltages, are with respect to network ground terminal. 4. Differential voltage values are at the noninverting (A) terminal with respect to the inverting (B) terminal. 5. Common-mode input voltage is the average of the voltages at the A and B inputs. DISSIPATION RATING TABLE PACKAGE TA 25C POWER RATING DERATING FACTOR ABOVE TA = 25C TA = 70C POWER RATING TA = 125C POWER RATING D 950 mW 7.6 mW/C 608 mW -- FK 1375 mW 11.0 mW/C 880 mW 275 mW 275 mW J 1375 mW 11.0 mW/C 880 mW N 1150 mW 9.2 mW/C 736 mW -- W 1000 mW 8.0 mW/C 640 mW 200 mW recommended operating conditions (see Note 6) SN75107A,, SN75107B,, SN75108A SN55107A UNIT MIN NOM MAX MIN NOM MAX 4.5 5 5.5 4.75 5 5.25 V - 4.5 -5 - 5.5 - 4.75 -5 - 5.25 V 5 5 V - 0.025 0.025 -5 - 0.025 V Common-mode input voltage, VIC (see Notes 7 and 8) -3 3 -3 3 V Input voltage, any differential input to GND (see Note 8) -5 3 -5 3 V High-level input voltage at strobe inputs, VIH(S) 2 5.5 2 5.5 V Low-level input voltage at strobe inputs, VIL(S) 0 0.8 0 0.8 V - 16 mA Supply voltage, VCC + Supply voltage, VCC - High-level input voltage between differential inputs, VIDH (see Note 7) Low-level input voltage between differential inputs, VIDL (see Note 7) 0.025 -5 Low-level output current, IOL - 16 Operating free-air temperature, TA - 55 125 0 70 C The algebraic convention, in which the less positive (more negative) limit is designated as minimum, is used in this data sheet for input voltage levels only. NOTES: 6. When using only one channel of the line receiver, the strobe input (G) of the unused channel should be grounded and at least one of the differential inputs of the unused receiver should be terminated at some voltage between - 3 V and 3 V. 7. The recommended combinations of input voltages fall within the shaded area in Figure 1. 8. The common-mode voltage may be as low as - 4 V provided that the more positive of the two inputs is not more negative than - 3 V. 4 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN55107A, SN75107A, SN75107B, SN75108A DUAL LINE RECEIVERS SLLS069D - JANUARY 1977 - REVISED APRIL 1998 RECOMMENDED COMBINATIONS OF INPUT VOLTAGES 3 Input A to GND Voltage - V 2 1 0 -1 -2 -3 -4 -5 -5 -4 -3 -2 -1 0 1 2 3 Input B to GND Voltage - V NOTE A: Recommended input-voltage combinations are in the shaded area. Figure 1. Recommended Combinations of Input Voltages POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 5 SN55107A, SN75107A, SN75107B, SN75108A DUAL LINE RECEIVERS SLLS069D - JANUARY 1977 - REVISED APRIL 1998 electrical characteristics over recommended free-air temperature range (unless otherwise noted) TEST CONDITIONS PARAMETER VOH High level output voltage High-level VCC = MIN, VIDH = 25 mV, mV VIC = - 3 V to 3 V VIL(S) = 0.8 V, IOH = - 400 A A, VOL Low level output voltage Low-level VCC = MIN, VIDL = - 25 mV mV, VIC = - 3 V to 3 V VIH(S) = 2 V, IOL = 16 mA, mA IIH High level input current High-level IIL Low-level input current A B A B VCC = MAX VID = 5 V VID = - 5 V VCC = MAX VID = - 5 V VID = 5 V '107A, SN75107B MIN TYP SN75108A MAX MIN TYP MAX 24 2.4 UNIT V 04 0.4 04 0.4 30 75 30 75 30 75 30 75 V A - 10 - 10 - 10 - 10 40 40 A 1 1 mA - 1.6 16 - 1.6 16 mA 80 80 A 2 2 mA - 3.2 - 3.2 mA A IIH High-level input current into g 1G or 2G VCC = MAX, VIH(G) = 2.4 V VCC = MAX, VIH(G) = MAX VCC + IIL Low-level input current into 1G or 2G VCC = MAX MAX, IIH High level input current into S High-level VCC = MAX, VIH(S) = 2.4 V VCC = MAX, VIH(S) = MAX VCC + IIL IOH Low-level input current into S High-level output current VCC = MAX, VIL(S)= 0.4 V VCC = MIN, VOH = MAX VCC + IOS Short-circuit output current VCC = MAX ICCH + Supply y current from VCC +, outputs high VCC = MAX MAX, TA = 25C 18 30 18 30 mA ICCH - Supply current from VCC -, outputs high VCC = MAX, TA = 25C - 8.4 - 15 - 8.4 - 15 mA VIL(G) = 0 0.4 4V 250 - 18 - 70 A mA For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions. All typical values are at VCC + = 5 V, VCC - = - 5 V, TA = 25C. Not more than one output should be shorted at a time. switching characteristics, VCC = 5 V, TA = 25C, RL = 390 (see Figure 2) TEST CONDITIONS PARAMETER 6 tPLH(D) Propagation delay output,, g y time,, low- to high-level g from differential inputs A and B CL = 50 pF tPHL(D) Propagation g delay y time,, highg to low-level output,, from differential inputs A and B CL = 50 pF tPLH(S) Propagation g delay y time,, low- to high-level g output,, from strobe input G or S CL = 50 pF tPHL(S) Propagation g delay y time, highg to low-level output, from strobe input G or S CL = 50 pF '107A, SN75107B MIN TYP MAX 17 25 CL = 15 pF 17 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 8 MAX 19 25 19 25 13 20 13 20 15 CL = 15 pF CL = 15 pF TYP 25 CL = 15 pF 10 SN75108A MIN 15 UNIT ns ns ns ns SN55107A, SN75107A, SN75107B, SN75108A DUAL LINE RECEIVERS SLLS069D - JANUARY 1977 - REVISED APRIL 1998 PARAMETER MEASUREMENT INFORMATION Differential Input Output `107A, SN75107B VCC - 1A 1Y 1B Pulse Generator (see Note A) CL 50 pF (see Note C) 50 V ref 100 mV (see Note D) 2A 2B 2Y 390 1G S 2G VCC+ 390 Output SN75108A, CL 15 pF (see Note C) 50 Strobe Input (see Note B) Pulse Generator (see Note A) TEST CIRCUIT 200 mV Input A 100 mV 100 mV 0V t p1 t p2 3V 1.5 V Strobe Input G or S t PHL(D) t PLH(D) 1.5 V t PHL(S) t PLH(S) VOH Output Y 1.5 V 1.5 V 1.5 V 1.5 V VOL VOLTAGE WAVEFORMS NOTES: A. The pulse generators have the following characteristics: ZO = 50 , tr = 10 5 ns, tf = 10 5 ns, tpd1 = 500 ns, PRR 1 MHz, tpd2 = 1 s, PRR 500 kHz. B. Strobe input pulse is applied to Strobe 1G when inputs 1A-1B are being tested, to Strobe S when inputs 1A-1B or 2A-2B are being tested, and to Strobe 2G when inputs 2A-2B are being tested. C. CL includes probe and jig capacitance. D. All diodes are 1N916. Figure 2. Test Circuit and Voltage Waveforms POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 7 SN55107A, SN75107A, SN75107B, SN75108A DUAL LINE RECEIVERS SLLS069D - JANUARY 1977 - REVISED APRIL 1998 TYPICAL CHARACTERISTICS OUTPUT VOLTAGE vs DIFFERENTIAL INPUT VOLTAGE HIGH-LEVEL INPUT CURRENT (1A OR 2A) vs FREE-AIR TEMPERATURE 6 100 VCC = 5 V IIIH IH - High-Level Input Current - A SN75108A VO VO - Output Voltage - V 5 Noninverting Inputs Inverting Inputs 4 '107A, SN75107B 3 AAA AAA 2 1 VCC = 5 V RL = 400 TA = 25 C 0 - 40 - 30 - 20 - 10 0 10 20 30 80 60 40 20 0 - 75 40 - 50 - 25 Figure 3 50 75 100 125 PROPAGATION DELAY TIME (DIFFERENTIAL INPUTS) vs FREE-AIR TEMPERATURE 40 30 VCC = 5 V VCC = 5 V 35 t pd - Propagation Delay Time - ns 25 | I CCH |- Supply Current - mA 25 Figure 4 SUPPPLY CURRENT (OUTPUTS HIGH) vs FREE-AIR TEMPERATURE ICC + 20 15 10 ICC - 5 0 - 75 - 50 - 25 0 25 50 75 100 125 30 RL = 390 CL = 50 pF 25 20 tPLH(D) 15 tPHL(D) 10 5 0 - 75 - 50 TA - Free-Air Temperature - C - 25 0 25 Figure 6 Values below 0C and above 70C apply to SN55107A only. POST OFFICE BOX 655303 50 75 100 TA - Free-Air Temperature - C Figure 5 8 0 TA - Free-Air Temperature - C VID - Differential Input Voltage - mV * DALLAS, TEXAS 75265 125 SN55107A, SN75107A, SN75107B, SN75108A DUAL LINE RECEIVERS SLLS069D - JANUARY 1977 - REVISED APRIL 1998 PROPAGATION DELAY TIME (LOW-TO-HIGH LEVEL) (DIFFERENTIAL INPUTS) vs FREE-AIR TEMPERATURE 120 VCC = 5 V CL = 15 pF 100 RL = 3900 80 60 RL = 1950 40 RL = 390 20 0 - 75 - 50 - 25 0 25 50 75 100 PROPAGATION DELAY TIME (LOW-TO-HIGH LEVEL) (DIFFERENTIAL INPUTS) vs FREE-AIR TEMPERATURE 40 ttPLH(D) PLH(D) - Propagation Delay Time - ns ttPLH(D) PLH(D) - Propagation Delay Time - ns TYPICAL CHARACTERISTICS VCC = 5 V CL = 15 pF 35 30 RL = 390 25 20 15 RL = 1950 RL = 3900 10 5 0 - 75 125 - 50 - 25 TA - Free-Air Temperature - C VCC = 5 V RL = 390 CL = 50 pF 35 t pd - Propagation Delay Time - ns t pd - Propagation Delay Time - ns 100 125 40 30 25 20 tPHL(S) 10 0 - 75 75 SN75108A PROPAGATION DELAY TIME (STROBE INPUTS) vs FREE-AIR TEMPERATURE 40 5 50 Figure 8 SN75108A PROPAGATION DELAY TIME (STROBE INPUTS) vs FREE-AIR TEMPERATURE 15 25 TA - Free-Air Temperature - C Figure 7 35 0 tPLH(S) - 50 VCC = 5 V RL = 390 CL = 15 pF 30 25 20 tPLH(S) 15 10 tPHL(S) 5 - 25 0 25 50 75 100 125 0 - 75 - 50 TA - Free-Air Temperature - C - 25 0 25 50 75 100 125 TA - Free-Air Temperature - C Figure 9 Figure 10 Values below 0C and above 70C apply to SN55107A only. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 9 SN55107A, SN75107A, SN75107B, SN75108A DUAL LINE RECEIVERS SLLS069D - JANUARY 1977 - REVISED APRIL 1998 APPLICATION INFORMATION basic balanced-line transmission system The '107A, SN75107B, and SN75108A dual line devices are designed specifically for use in high-speed data-transmission systems that utilize balanced terminated transmission lines, such as twisted-pair lines. The system operates in the balanced mode, so noise induced on one line is also induced on the other. The noise appears common mode at the receiver input terminals, where it is rejected. The ground connection between the line driver and receiver is not part of the signal circuit; therefore, system performance is not affected by circulating ground currents. The unique driver-output circuit allows terminated transmission lines to be driven at normal line impedances. High-speed system operation is ensured because line reflections are virtually eliminated when terminated lines are used. Crosstalk is minimized by low signal amplitudes and low line impedances. The typical data delay in a system is approximately 30 + 1.3 L ns, where L is the distance in feet separating the driver and receiver. This delay includes one gate delay in both the driver and receiver. Data is impressed on the balanced-line system by unbalancing the line voltages with the driver output current. The driven line is selected by appropriate driver-input logic levels. The voltage difference is approximately: VDIFF 1/2IO(on) * RT High series line resistance causes degradation of the signal. However, the receivers detect signals as low as 25 mV. For normal line resistances, data can be recovered from lines of several thousand feet in length. Line-termination resistors (RT) are required only at the extreme ends of the line. For short lines, termination resistors at the receiver only may be adequate. The signal amplitude is then approximately: VDIFF IO(on) * RT RT RT RT RT A Data Input B C Inhibit Transmission Line Having Characteristic Impedance ZO RT = ZO/2 D Y L Driver SN55110A, SN75110A, SN75112 Strobes Receiver `107A, SN75107B, SN75108A Figure 11. Typical Differential Data Line data-bus or party-line system The strobe feature of the receivers and the inhibit feature of the drivers allow these dual line devices to be used in data-bus or party-line systems. In these applications, several drivers and receivers can share a common transmission line. An enabled driver transmits data to all enabled receivers on the line while other drivers and receivers are disabled. Data is time multiplexed on the transmission line. The device specifications allow widely varying thermal and electrical environments at the various driver and receiver locations. The data-bus system offers maximum performance at minimum cost. 10 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN55107A, SN75107A, SN75107B, SN75108A DUAL LINE RECEIVERS SLLS069D - JANUARY 1977 - REVISED APRIL 1998 APPLICATION INFORMATION Drivers SN55110A, SN75110A, SN75112 Receiver 1 Receiver 2 Receiver 4 Y Y Strobes RT Strobes Y Strobes RT RT RT Location 2 A Data Input Driver 1 Driver 3 B C Inhibit D A B B C C D Location 1 Driver 4 A Location 3 D Receivers `107A, SN75107B, SN75108A Location 4 Figure 12. Typical Differential Party Line unbalanced or single-line systems These dual line circuits also can be used in unbalanced or single-line systems. Although these systems do not offer the same performance as balanced systems for long lines, they are adequate for very short lines where environmental noise is not severe. The receiver threshold level is established by applying a dc reference voltage to one receiver input terminal. The signal from the transmission line is applied to the remaining input. The reference voltage should be optimized so that signal swing is symmetrical about it for maximum noise margin. The reference voltage should be in the range of - 3 V to 3 V. It can be provided by a voltage supply or by a voltage divider from an available supply voltage. A single-ended output from a driver can be used in single-line systems. Coaxial or shielded line is preferred for minimum noise and crosstalk problems. For large signal swings, the high output current (typically 27 mA) of the SN75112 is recommended. Drivers can be paralleled for higher current. When using only one channel of the line drivers, the other channel should be inhibited and/or have its outputs grounded. SN55110A, SN75110A, SN75112 `107A, SN75107B, SN75108A R Output A Input B C Inhibit D Input Vref Output Strobes VO = - IO * R Figure 13. Single-Ended Operation POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 11 SN55107A, SN75107A, SN75107B, SN75108A DUAL LINE RECEIVERS SLLS069D - JANUARY 1977 - REVISED APRIL 1998 APPLICATION INFORMATION SN75108A dot-AND output connections The SN75108A line receiver features an open-collector-output circuit that can be connected in the dot-AND logic configuration with other similar open-collector outputs. This allows a level of logic to be implemented without additional logic delay. SN75108A SN75108A Output Dot-AND Connection SN5401/SN7401 or Equivalent Figure 14. Dot-AND Connection increasing common-mode input voltage range of receiver The common-mode voltage range (CMVR) is defined as the range of voltage applied simultaneously to both input terminals that, if exceeded, does not allow normal operation of the receiver. The recommended operating CMVR is 3 V, making it useful in all but the noisiest environments. In extremely noisy environments, common-mode voltage can easily reach 10 V to 15 V if some precautions are not taken to reduce ground and power supply noise, as well as crosstalk problems. When the receiver must operate in such conditions, input attenuators should be used to decrease the system common-mode noise to a tolerable level at the receiver inputs. Differential noise is also reduced by the same ratio. These attenuators were omitted intentionally from the receiver input terminals so the designer can select resistors that are compatible with his particular application or environment. Furthermore, the use of attenuators adversely affects the input sensitivity, the propagation delay time, the power dissipation, and in some cases (depending on the selected resistor values) the input impedance; thereby reducing the versatility of the receiver. The ability of the receiver to operate with approximately 15 V common-mode voltage at the inputs has been checked using the circuit shown in Figure 15. Resistors R1 and R2 provide a voltage-divider network. Dividers with three different values presenting a 5-to-1 attenuation were used to operate the differential inputs at approximately 3 V common-mode voltage. Careful matching of the two attenuators is needed to balance the overdrive at the input stage. The resistors used are shown in Table 1. Table 1 12 Attenuator 1: R1 = 2 k, Attenuator 2: R1 = 6 k, R2 = 1.5 k Attenuator 3: R1 = 12 k, R2 = 3 k POST OFFICE BOX 655303 R2 = 0.5 k * DALLAS, TEXAS 75265 SN55107A, SN75107A, SN75107B, SN75108A DUAL LINE RECEIVERS SLLS069D - JANUARY 1977 - REVISED APRIL 1998 APPLICATION INFORMATION increasing common-mode input voltage range of receiver (continued) Table 2 shows some of the typical switching results obtained under such conditions. Table 2. Typical Propagation Delays for Receiver With Attenuator Test Circuit Shown in Figure 15 DEVICE PARAMETERS INPUT ATTENUATOR TYPICAL (NS) 1 20 2 32 3 42 1 22 2 31 3 33 1 36 2 47 3 57 1 29 2 38 3 41 tPLH '107A SN75107B tPHL tPLH SN75108A tPHL 16 V 5 V One Attenuator on Each Input Receiver RL = 390 or - 14 V 14 V R1 R2 - 16 V 5 V 15 V or - 15 V R1 R2 Figure 15. Common-Mode Circuit for Testing Input Attenuators With Results Shown in Table 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 13 SN55107A, SN75107A, SN75107B, SN75108A DUAL LINE RECEIVERS SLLS069D - JANUARY 1977 - REVISED APRIL 1998 Two methods of terminating a transmission line to reduce reflections are shown in Figure 16. The first method uses the resistors as the attenuation network and line termination. The second method uses two additional resistors for the line terminations. APPLICATION INFORMATION R1 (see Note A) R1 Method 1 Method 2 R3 R2 (see Note A) R3 R2 R3 R3 R2 R2 (see Note A) R3 R3 R1 R1 R1 + R2 > ZO R3 = ZO /2 R3 = R1 + R2 = ZO /2 NOTE A: To minimize the loading, the values of R1 and R2 should be fairly large. Examples of possible values are shown in Table 1. Figure 16. Termination Techniques For party-line operation, method 2 should be used as shown in Figure 17. Attenuation Network R3 + Z2O R3 + Z2O R3 + Z2O R3 + Z2O Figure 17. Party-Line Termination Technique 14 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN55107A, SN75107A, SN75107B, SN75108A DUAL LINE RECEIVERS SLLS069D - JANUARY 1977 - REVISED APRIL 1998 APPLICATION INFORMATION furnace control using the SN75108A The furnace control circuit in Figure 18 is an example of the possible use of the SN75108A series in areas other than what would normally be considered electronic systems. A description of the operation of this control follows. When the room temperature is below the desired level, the resistance of the room temperature sensor is high and channel 1 noninverting input is below (less positive than) the reference level set on the input differential amplifier. This situation causes a low output, operating the heat-on relay and turning on the heat. The channel 2 noninverting input is below the reference level when the bonnet temperature of the furnace reaches the desired level. This causes a low output, thus operating the blower relay. Normally the furnace is shut down when the room temperature reaches the desired level and the channel 1 output goes high, turning the heat off. The blower remains on as long as the bonnet temperature is high, even after the heat-on relay is off. There is also a safety switch in the bonnet that shuts down the furnace if the temperature there exceeds desired limits. The types of temperature-sensing devices and bias-resistor values used are determined by the particular operating conditions encountered. 5V Bonnet Temp. Sensor +T Room Temp. Sensor Bonnet Upper Limit Switch -T Channel 1 1Y A Room Temp. Setting To Heat-on Relay Return B 2Y 2A Blower on Control To Blower Relay Return 2B Channel 2 Figure 18. Furnace Control Using SN75108A POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 15 SN55107A, SN75107A, SN75107B, SN75108A DUAL LINE RECEIVERS SLLS069D - JANUARY 1977 - REVISED APRIL 1998 APPLICATION INFORMATION repeaters for long lines In some cases, the driven line may be so long that the noise level on the line reaches the common-mode limits or the attenuation becomes too large and results in poor reception. In such a case, a simple application of a receiver and a driver as repeaters [shown in Figure 19(a)] restores the signal level and allows an adequate signal level at the receiving end. If multichannel operation is desired, then proper gating for each channel must be sent through the repeater station using another repeater set as in Figure 19(b). Repeaters Data In Driver P Data In Driver Receiver Driver (a) SINGLE-CHANNEL LINE P Clock In Strobe Ckt Data Out Receiver Data Out P Driver Receiver Receiver P Driver Receiver P Receiver P (b) MULTICHANNEL LINE WIDTH WITH STROBE Figure 19. Receiver-Driver Repeaters receiver as dual differential comparator There are many applications for differential comparators, such as voltage comparison, threshold detection, controlled Schmitt triggering, and pulse-width control. As a differential comparator, a '107A or SN75108A can be connected to compare the noninverting input terminal with the inverting input as shown in Figure 20. The output is high or low, resulting from the A input being greater or less than the reference. The strobe inputs allow additional control over the circuit so that either output, or both, can be inhibited. Strobe 1 1A Reference 1 Output 1 1B Strobe 1, 2 2A Output 2 Reference 2 2B Strobe 2 Figure 20. SN75107A Series Receiver as a Dual Differential Comparator 16 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN55107A, SN75107A, SN75107B, SN75108A DUAL LINE RECEIVERS SLLS069D - JANUARY 1977 - REVISED APRIL 1998 APPLICATION INFORMATION window detector The window detector circuit in Figure 21 has a large number of applications in test equipment and in determining upper limits, lower limits, or both at the same time, such as detecting whether a voltage or signal has exceeded its window limits. Illumination of the upper-limit (lower-limit) indicator shows that the input voltage is above (below) the selected upper (lower) limit. A mode selector is provided for selecting the desired test. For window detecting, the upper-and-lower-limits test position is used. 5V 5 V -5 V 1 k 1 k 500 Set Upper Limit Upper-Limit Indicator 5 k 500 Input From Test Point Lower-Limit Indicator Set Lower Limit 1 k 4 3 4.7 k 2 4.7 k 4.7 k 1 Mode Selector MODE SELECTOR LEGEND POSITION 1 2 3 4 CONDITION Off Test for Upper Limit Test for Lower Limit Test for Upper and Lower Limits Figure 21. Window Detector Using SN75108A POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 17 SN55107A, SN75107A, SN75107B, SN75108A DUAL LINE RECEIVERS SLLS069D - JANUARY 1977 - REVISED APRIL 1998 APPLICATION INFORMATION temperature controller with zero-voltage switching The circuit in Figure 22 switches an electric-resistive heater on or off by providing negative-going pulses to the gate of a triac during the time interval when the line voltage is passing through zero. The pulse generator is the 2N5447 and four diodes. This portion of the circuit provides negative-going pulses during the short time (approximately 100 s) when the line voltage is near zero. These pulses are fed to the inverting input of one channel of the SN75108A. If the room temperature is below the desired level, the resistance of the thermistor is high and the noninverting input of channel 2 is above the reference level determined by the thermostat setting. This provides a high-level output from channel 2. This output is ANDed with the positive-going pulses from the output of channel 1, which are reinverted in the 2N5449. 250 F + 10-V Zener 5-V Zener VCC + 1A 1B 2N5447 VCC - 250 F + Channel 1 Channel 2 2A 2B 120 V to 220 V, 60 Hz -T SN75108A GND 2N5449 Thermostat Setting Heater Load Figure 22. Zero-Voltage Switching Temperature Controller 18 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK. In order to minimize risks associated with the customer's applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI's publication of information regarding any third party's products or services does not constitute TI's approval, warranty or endorsement thereof. Copyright 1999, Texas Instruments Incorporated