IDTQS32390 HIGH-SPEED CMOS QUICKSWITCH 16:8 MULTIPLEXER INDUSTRIAL TEMPERATURE RANGE QUICKSWITCH(R) PRODUCTS HIGH-SPEED CMOS QUICKSWITCH 16:8 MULTIPLEXER IDTQS32390 FEATURES: DESCRIPTION: * * * * * * * * The QS32390 provides a 16:8 multiplexer logic switch. The QS32390 has an internal 25 resistor to reduce reflection noise in high-speed applications. The enable inputs connect one of two inputs to the common I/O pin, respectively. The multiplexer function can be used to select and route logic signals for zero delay, isolate bus capacitance, form crossbar switches, etc. Mux/Demux devices provide an order of magnitude faster speed than equivalent logic devices. The QS32390 is characterized for operation at -40C to +85C. Enhanced N channel FET with no inherent diode to Vcc 16:8 multiplexer function with zero delay bidirectional switches connect inputs to outputs 5 Zero propagation delay, zero ground bounce Undershoot clamp diodes on all switch and control inputs Direct bidirectional connection for mux, demux resistors for low noise 25 Available in QSOP package APPLICATIONS: * Video, audio, graphics switching, muxing * Hot-swapping, hot-docking * Voltage translation (5V to 3.3V) FUNCTIONAL BLOCK DIAGRAM A0 AB 0 A7 AB 7 AEN B0 B7 BEN The IDT logo is a registered trademark of Integrated Device Technology, Inc. INDUSTRIAL TEMPERATURE RANGE MARCH 2002 1 c 2002 Integrated Device Technology, Inc. DSC-5752/2 IDTQS32390 HIGH-SPEED CMOS QUICKSWITCH 16:8 MULTIPLEXER ABSOLUTE MAXIMUM RATINGS(1) PIN CONFIGURATION A0 1 B0 2 AB0 3 A1 B1 INDUSTRIAL TEMPERATURE RANGE Symbol Description Max Unit VTERM(2) Supply Voltage to Ground -0.5 to +7 V 28 27 VCC A7 VTERM(3) DC Switch Voltage Vs -0.5 to +7 V VTERM(3) DC Input Voltage VIN -0.5 to +7 V B7 AB7 VAC AC Input Voltage (pulse width 20ns) -3 V 4 26 25 IOUT DC Output Current 120 mA 5 24 A6 PMAX Maximum Power Dissipation (TA = 85C) AB1 6 23 B6 TSTG Storage Temperature A2 7 22 AB6 B2 8 21 A5 AB2 9 20 B5 10 19 AB5 B3 11 18 A4 AB3 AEN 12 13 17 B4 16 AB4 GND 14 15 BEN A3 0.5 W -65 to +150 C NOTE: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. Vcc terminals. 3. All terminals except Vcc. CAPACITANCE (TA = +25C, f = 1.0MHZ, VIN = 0V, VOUT = 0V) QSOP TOP VIEW Pins Typ. Max. (1) Unit Control Pins 4 5 pF pF Quickswitch Channels Demux 5 7 (Switch OFF) Mux 9 10 NOTE: 1. This parameter is measured at characterization but not tested. PIN DESCRIPTION Pin Names I/O A0 - A9 I/O Bus A Description B0 - B9 I/O Bus B AEN, BEN I Bus Switch Enable FUNCTION TABLE(1) AEN BEN H L H L A0 - A9 B 0 - B9 H Off Off Disconnect H On Off A to AB L Off On B to AB L On On A, B to AB NOTE: 1. H = HIGH Voltage Level L = LOW Voltage Level 2 Function IDTQS32390 HIGH-SPEED CMOS QUICKSWITCH 16:8 MULTIPLEXER INDUSTRIAL TEMPERATURE RANGE DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE Following Conditions Apply Unless Otherwise Specified: Industrial: TA = -40C to +85C, VCC = 5.0V 5% Symbol Parameter Test Conditions VIH Input HIGH Level Guaranteed Logic HIGH for Control Pins VIL Input LOW Level Guaranteed Logic LOW for Control Pins IIN Input LeakageCurrent (Control Inputs)(2) 0V VIN VCC IOZ Off-State Output Current (Hi-Z) Switch ON Resistance RON(3) VP Pass Voltage(2) Min. Typ.(1) Max. Unit 2 -- -- V -- -- 0.8 V -- -- 1 A 0V VOUT VCC, Switches OFF -- -- 1 A VCC = Min., VIN = 0V, ION = 30mA VCC = Min., VIN = 2.4V, ION =15mA VIN = VCC = 5V, IOUT = -5A 15 15 3.7 20 19 4 35 40 4.2 NOTES: 1. Typical values are at VCC = 5.0V, TA = 25C. 2. Pass Voltage is guaranteed but not production tested. 3. ROUT changed on March 8, 2002. See rear page for more information. TYPICAL ON RESISTANCE vs VIN AT VCC = 5V 80 R ON (ohms) 70 60 50 40 30 20 10 0 0.0 0.5 1.0 1.5 2.0 V IN (Volts) 3 2.5 3.0 3.5 V IDTQS32390 HIGH-SPEED CMOS QUICKSWITCH 16:8 MULTIPLEXER INDUSTRIAL TEMPERATURE RANGE POWER SUPPLY CHARACTERISTICS Symbol Test Conditions(1) Parameter Max. Unit ICCQ Quiescent Power Supply Current VCC = Max., VIN = GND or Vcc, f = 0 3 A ICC Power Supply Current per Control Input HIGH (2) VCC = Max., VIN = 3.4V, f = 0 1.5 mA ICCD Dynamic Power Supply Current per MHz(3) VCC = Max., A, B, and AB pins open 0.25 mA/MHz Control Inputs Toggling at 50% Duty Cycle NOTES: 1. For conditions shown as Min. or Max., use the appropriate values specified under DC Electrical Characteristics. 2. Per TLL driven input (VIN = 3.4V, control inputs only). A, B, and AB pins do not contribute to Icc. 3. This current applies to the control inputs only and represents the current required to switch internal capacitance at the specified frequency. The A, B, and AB I/Os generate no significant AC or DC currents as they transition. This parameter is guaranteed but not production tested. SWITCHING CHARACTERISTICS OVER OPERATING RANGE TA = -40C to +85C, VCC = 5.0V 5%; CLOAD = 50pF, RLOAD = 500 unless otherwise noted. Symbol Parameter tPLH Data Propagation Delay (2,4) tPHL AxBx to CxDx, CxDx to AxBx tPZH Switch Turn-on Delay tPZL BE to Ax, Bx, Cx, Dx tPHZ Switch Turn-off Delay (2) tPLZ BE to Ax, Bx, Cx, Dx Min. (1) Typ. Max. Unit -- -- 1.25(3) ns 1.5 -- 7.5 ns -- -- 5.5 ns NOTES: 1. Minimums are guaranteed but not production tested. 2. This parameter is guaranteed but not production tested. 3. The time constant for the switch alone is of the order of 1.25ns for CL = 50pF. 4. The bus switch contributes no propagation delay other than the RC delay of the ON resistance of the switch and the load capacitance. Since this time constant is much smaller than the rise and fall times of typical driving signals, it adds very little propagation delay to the system. Propagation delay of the bus switch, when used in a system, is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. 4 IDTQS32390 HIGH-SPEED CMOS QUICKSWITCH 16:8 MULTIPLEXER INDUSTRIAL TEMPERATURE RANGE ORDERING INFORMATION IDTQS XXXXX Device Type XX Package Q Quarter Size Outline Package 32390 High Speed CMOS QuickSwitch 16:8 Multiplexer As per PCN L0201-02, the Output Resistance (RON) specifications have changed as of March 8, 2002. The original specifications were: Parameter RON Description Min. Typ. Max. Unit VCC = Min, VIN = 0V, ION = 30mA 20 28 40 VCC = Min, VIN = 2.4V, ION = 15mA 24 35 48 CORPORATE HEADQUARTERS 2975 Stender Way Santa Clara, CA 95054 for SALES: 800-345-7015 or 408-727-6116 fax: 408-492-8674 www.idt.com 5 for Tech Support: logichelp@idt.com (408) 654-6459