Keysight Technologies
InniiVision Oscilloscope Probes
and Accessories
For 2000 X-, 3000 X-, 4000 X-, 6000 X-, 5000,
6000, and 7000 Series
Selection Guide
Data Sheet
02 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
Probe Compatibility Table .................................................................................................. 3
Passive Probes .................................................................................................................... 5
High-voltage Passive Probes ............................................................................................ 7
InniiMax Active Probes and Accessories ......................................................................... 8
InniiMode Active Probes and Accessories....................................................................... 10
High-voltage Differential Active Probes ........................................................................... 12
Single-ended Active Probes ............................................................................................... 15
Mixed Signal Oscilloscope Logic Probes .......................................................................... 17
Clamp-on Current Probes ................................................................................................. 19
High-Sensitivity Current Probes ....................................................................................... 21
Wedge Probe Adapters ...................................................................................................... 23
Miscellaneous Accessories ............................................................................................... 24
N2744A T2A Probe Interface Adapter ............................................................................... 26
Recommended Probes for Low-/Mid-Speed Bus Measurements .................................. 27
Table of Contents
To achieve the best results from your scope, you need the right probes and accessories
for your particular application. That’s why Keysight Technologies, Inc. offers a complete
family of innovative probes and accessories for InniiVision oscilloscopes. For the most
up-to-date and complete information about Keysight’s accessories, please visit our Web
site at: www.keysight.com/nd/probes
03 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
Probe Compatibility Table
For ordering information when replacing your probe or probe accessory: Refer directly to the page number listed in the table of
contents for your probe model.
To assist you in selecting the proper probe for your application: Use our probe compatibility table below to nd the probes that are
recommended for use with your 2000 X-, 3000 X-, 4000 X-, 6000 X-, 5000, 6000, and 7000 Series InniiVision oscilloscope.
Probe type Probe model MSO/DSO
2000 X1
MSO/DSO
3000 X
MSO/DSO
4000 X/6000 X2
Passive probes,
page 4
N2862B 10:1 150 MHz
(included in 70/100 MHz models)
N2863B 10:1 300 MHz
(included in 200 MHz models)
N2890A 10:1 500 MHz
(included in 350/500 MHz/1 GHz models)
Recommended Recommended Recommended
N2894A 10:1 700 MHz (included in 4000 X models) Compatible Compatible Compatible
N2889A 1:1/10:1 350 MHz Recommended Recommended Recommended
High-voltage passive
probes, page 7
10076C 4 kV Recommended Recommended Recommended
N2771B 30 kV Recommended Recommended Recommended
1130A - 1134A 1.5 GHz - 7 GHz Incompatible Recommended Recommended
Differential active probes,
page 8
N2750A - N2752A 1.5 GHz - 6 GHz Incompatible Recommended Recommended
1141A 200 MHz (use with 1142A) Incompatible Recommended Recommended
N2791A 25 MHz Recommended Recommended Recommended
N2891A 70 MHz Recommended Recommended Recommended
N2790A 100 MHz (with AutoProbe) Incompatible Recommended Recommended
N2792A 200 MHz Incompatible Recommended Recommended
N2818A 200 MHz (with AutoProbe) Incompatible Recommended Recommended
N2793A 800 MHz Incompatible Recommended Recommended
N2819A 800 MHz (with AutoProbe) Incompatible Recommended Recommended
N2804A 300 MHz Incompatible Recommended Recommended3
N2805A 200 MHz Incompatible Recommended Recommended3
Single-ended active probes,
page 15
N2795A 1 GHz (with AutoProbe) Incompatible Recommended Recommended
N2796A 2 GHz (with AutoProbe) Incompatible Recommended Recommended
N2797A 1.5 GHz (with AutoProbe) Incompatible Recommended Recommended
N7020A 2 GHz Incompatible Incompatible Recommended3
MSO logic probes,
page 17
01650-61607 16-channel Incompatible Recommended Recommended
N6459-60001 8-channel MSO cable
(included in 2000 X-Series MSOs)
Recommended Incompatible Incompatible
N6450-60001 16-channel MSO cable
(included in 3000 and 4000 X-Series MSOs)
Incompatible Recommended Recommended
N2756A 16-Channel MSO cable
(included in 6000 X-Series MSOs)
Incompatible Recommended Recommended
Current probes,
page 19
1146B 100 kHz Recommended Recommended Recommended
N2780B 2 MHz (use with N2779A) Recommended Recommended Recommended
N2781B 10 MHz (use with N2779A) Recommended Recommended Recommended
N2782B 50 MHz (use with N2779A) Recommended Recommended Recommended
N2783B 100 MHz (use with N2779A) Recommended Recommended Recommended
1147B 50 MHz (with AutoProbe) Incompatible Recommended Recommended
N2893A 100 MHz (with AutoProbe) Incompatible Recommended Recommended
N2820A 3 MHz/50 uA High Sensitivity,
2 channel (with AutoProbe)
Incompatible Recommended Recommended
N2821A 3 MHz/50 uA High Sensitivity,
1 channel (with AutoProbe)
Incompatible Recommended Recommended
1. The 2000 X-Series does not support AutoProbe interface active probes.
2. The 4000 X- and 6000 X-Series comes with the Inniium AutoProbe interface for higher probe power support.
3. Recommended with 4000 X-Series only.
04 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
Probe Compatibility Table (continued)
Probe type Probe model DSO5000A
100 MHz
DSO5000A
300 - 500 MHz
MSO/DSO6000A4
100 MHz
MSO/DSO6000A4
300 MHz - 1 GHz
MSO/DSO7000A/B
100 MHz - 1 GHz
Passive probes,
page 5
N2863B 10:1 300 MHz
(included in 5000 Series
100/300 MHz)
Recommended Recommended Recommended Compatible
10070D 1:1 20 MHz Recommended Recommended Recommended Recommended
10073D 10:1 500 MHz (included in
6000/7000 Series 300 MHz to
1 GHz and 5000 Series 500 MHz)
Compatible Recommended Compatible Recommended
10074D 10:1 150 MHz
(included in 6000 Series 100 MHz)
Recommended Compatible Recommended Compatible
N2873A 10: 1 500 MHz
(optional to 7000B)
Recommended Recommended Compatible Recommended
High-voltage
passive probes
page 7
10076C 4 kV Recommended Recommended Recommended Recommended
N2771B 30 kV Recommended Recommended Recommended Recommended
Differential
active probes
page 8
1130A 1.5 GHz1Compatible Recommended Incompatible Recommended
N2750A 1.5 GHz Incompatible Incompatible Incompatible Incompatible
1141A 200 MHz (use with 1142A) Compatible Recommended Compatible Recommended
N2791A 25 MHz Recommended Recommended Recommended Recommended
N2891A 70 MHz Recommended Recommended Recommended Recommended
N2790A 100 MHz (with AutoProbe) Recommended Recommended Incompatible Recommended
N2792A 200 MHz Recommended Recommended Incompatible Recommended
N2818A 200 MHz (with AutoProbe) Incompatible Incompatible Incompatible Incompatible
N2793A 800 MHz Recommended Recommended Incompatible Recommended
N2819A 800 MHz (with AutoProbe) Incompatible Incompatible Incompatible Incompatible
N2804A 300 MHz Incompatible Incompatible Incompatible Incompatible
N2805A 200 MHz Incompatible Incompatible Incompatible Incompatible
Single-ended
active probes
page 15
N2795A 1 GHz (with AutoProbe) Recommended Recommended Incompatible Recommended
N2796A 2 GHz (with AutoProbe) Recommended Recommended Incompatible Recommended
N2797A 1.5 GHz (with AutoProbe) Incompatible Incompatible Incompatible Incompatible
N7020A 2 GHz Incompatible Incompatible Incompatible Incompatible
Mixed signal
oscilloscope
logic probes2
page 17
01650-61607 16-channel
N6450-60001 2x8-channel
(included in MSO6000A, MSO7000A/B)
Incompatible Incompatible Recommended Recommended
Current probes
page 19
1146B 100 kHz Recommended Recommended Recommended Recommended
N2780B 2 MHz (use with N2779A) Recommended Recommended Recommended Recommended
N2781B 10 MHz (use with N2779A) Recommended Recommended Recommended Recommended
N2782B 50 MHz (use with N2779A) Recommended Recommended Recommended Recommended
N2783B 100 MHz (use with N2779A) Recommended Recommended Recommended Recommended
1147B 50 MHz (with AutoProbe) Recommended Recommended Incompatible Recommended
N2893A 100 MHz (with AutoProbe) Recommended Recommended Incompatible Recommended
N2820A 3 MHz/50 uA High Sensitivity, 2
channel (with AutoProbe)
Incompatible Incompatible Incompatible Incompatible
N2821A 3 MHz/50 uA High Sensitivity, 1
channel (with AutoProbe)
Incompatible Incompatible Incompatible Incompatible
1. The 1130A probe amplier supports both single- and differential-ended measurements. Higher bandwidth InniiMax probe model 1131A, 1132A, and 1134A
are also supported by 3000 X-, 4000 X-, 6000 X-, 5000, 6000 300 MHz - 1 GHz models and, 7000 Series.
2. Recommended for InniiVision MSOs only.
3. These Inniium active probes are not supported by InniiVision Series scopes – 1152A, 1153A, 1154A, 1155A, 1159A, 1168A, 1169A, N2800A, N2801A,
N2802A, N2803A, N2830A, N2831A and N2832A..
4. MSO/DSO6000A 100-MHz models do not support any Keysight active probes with AutoProbe interface.
05 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
Passive Probes
– Designed for optimal performance with
your Keysight InniiVision Series oscil-
loscopes
– 1:1 and 10:1 attenuation
– 20 to 500 MHz
Rugged, high-quality probes at a
reasonable price
Keysight 10070-family passive probes are
a great choice if you’re looking for high
quality at a very reasonable price. These
general-purpose probes are designed
specically to give you optimal
performance with your InniiVision Series
oscilloscopes. Ruggedized for
general-purpose measurements, they
feature adurable cable and a solid
stainless steel probe body encased with
a hard, fracture-resistant plastic. They’re
designed and tested to ensure the probes
operate in the toughest of conditions
The N2862B, N2863B, N2889A, and
N2890A low-cost, general-purpose
passive probes provide up to 500 MHz
bandwidth and feature a high input
resistance of 10 MΩ for low probe loading.
These probes provide a 10:1 attenuation
ratio except for the N2889A which provides
a switch in the probe handle for switching
the attenuation ratio between 1:1 and 10:1.
The N2873A/N2894A are
500-MHz/700 MHz 10:1 miniature passive
probes that can be used with all
InniiVision Series. Compact 2.5-mm probe
head diameter, low input capacitance, and
various ne-pitch probe tip
accessories make the N2873A/N2894A
passive probes ideal for probing densely
populated IC components or
surface-mount devices used in today’s
high-speed digital applications. The
N2894A provides 700 MHz system
bandwidth when used in conjunction
with the 4000 X- and 6000 X-Series ≥ 1
GHz models. For more information about
N2870A Series passive probes and
accessories, check out Keysight’s literature
number, 5990-3930EN.
Accessories available for
10070D/73D/74D passive
probes
Accessories available for
N2873A/N2894A (and other
N287xA Series passive probes)
Standard accessories that come with each probe
N4848A Probe-tip-to-BNC (m) adapter,
qty 2
5081-7696 Ground lead with
alligator clip for 1007x and
N2862B/63B/89A/90A
N4847A Retractable hook tip for
1007xC/D (not compatible with
10076A/B), qty 2
N4849A Dual-test lead adapter
(for 10070/3/4x), qty 2
5081-7690 Replacement parts accessory kit
10072A Fine-pitch probing kit includes
10 SMT clips and 2 dual-lead
adapters
10075A 0.5 mm IC probing kit.
Contains four 0.5 mm IC clips
and 2 dual-lead adapters
0960-2900 Retractable hook tip for
N2862B/63B/89A/90A
N4827A PCB socket adapter for
N2862B/63B/89A/90A, qty 2
N4826A Dual-lead adapter for
N2862B/63B/89A/90A, qty 2
N4828A 5 mm ground spring for
N2862B/63B/89A/90A, qty 2
1250-3978 BNC adapter
10070D/10073C/10074C N2862B/N2863B/N2880A/
N2890A
N2873A /N2894A
Retractable hook tip, Qty 1
Colored identication tag,
2 each of 4 colors
Ground bayonet, Qty 1
IC insulation cap, Qty 1
Adjustment tool, Qty 1
Ground lead, Qty 1
BNC adapter, Qty 1
Retractable hook tip, qty
Colored identication tag,
2 each of 4 colors
Spring ground, qty 1
IC insulation cap, qty 1
Insulation cap, qty 1
Adjustment tool, qty 1
(with N2862B/63B),
qty 2 (with N2889A/90A)
Ground lead, qty 1
BNC adapter, qty 1
Probe tip, qty 1
Spring loaded probe tips, qty 2
Rigid probe tips, qty 2
Ground blade, qty 1
Ground spring, qty 1
Sprung hook, qty 1
Ground lead, qty 1
Copper pads, qty 2
IC cap – 0.5 mm,
0.65 mm, 0.8 mm,
1 mm, 1.27 mm, qty 1 each
BNC adapter, qty 1
Insulating cap, qty 1
Protection cap, qty 1
Trimmer tool, qty 1
Color coded rings, 3x4 colors
N4829A Probe tip kit (rigid and spring
loaded), 10 each
N4831A Sprung hook adapter
2.5 mm for N2870A/71A/
72A/73A/75A, N2894A, qty 2
N4837A Ground lead 15 cm, qty 2
0960-2908 10 self-adhesive copper pads
2x2
N4836A Dual lead-adapter, 2.5 mm,
10 cm, qty 2
0960-2977 Ground lead 11 cm to Miniclip
0960-2978 Ground lead 11 cm to 0.8mm
socket
0960-2979 Rigid probe tips, qty 5
N4838A Ground spring 2.5 mm, qty 2
0960-2981 Spring-loaded probe tip, qty 5
0960-2982 Ground blade 2.5mm
0960-2983 IC cap 2.5 - 0.5mm Green
0960-2984 IC cap 2.5 - 0.65mm Blue
0960-2985 Insulating cap 2.5mm
0960-2986 IC cap 2.5 - 1.27mm Black
0960-2987 IC cap 2.5 - 1.27mm Black
0960-2988 IC cap 2.5 - 0.8mm Gray
0960-2989 IC cap 2.5 - 1.0mm Brown
0960-2990 Adapter 2.5 to 0.8mm socket
N4863A 2.5mm probe tip-to-PCB
adapter, horizontal
N4864A 2.5mm probe tip-to-PCB
adapter, vertical
Accessories available for
N2862B, N2863B, N2889A, and
N2890A passive probe
06 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
Passive Probes (continued)
Ordering information for Keysight
passive probes
10070D 1:1 20 MHz passive probe
N2862B 10:1 150 MHz passive probe
10074D 10:1 150 MHz passive probe
N2863B 10:1 300 MHz passive probe
N2889A 10:1/1:1 350 MHz passive probe
10073D 10:1 500 MHz passive probe
N2890A 10:1 500 MHz passive probe
N2873A 10:1 500 MHz miniature
passive probe
N2894A 10:1 700 MHz miniature passive
probe
10070D 10073D 10074D N2862B/63B N2889A N2890A N2873A/
N2894A
Bandwidth 20 MHz 500 MHz 150 MHz 150 MHz/
300 MHz
350 MHz (at 10:1),
10 MHz (at 1:1)
500 MHz 500 /700 MHz
Risetime (calculated) < 17.5 ns < 700 ps < 2.33 ns < 2.33 ns/
< 1.16 ns
<1 ns (at 10:1),
< 35 ns (at 1:1)
< 700 ps < 700 ps/
< 500 ps
Attenuation ratio 1:1 10:1 10:1 10:1 1:1/10:1 switchable 10:1 10:1
Input resistance 1 MΩ 2.2 MΩ 10 MΩ 10 MΩ 10 MΩ (at 10:1)
1 MΩ (at 1:1)
10 MΩ 10 MΩ
Input capacitance Approx 70 pF Approx 12 pF Approx 15 pF Approx 15 pF Approx 11 pF (at 10:1),
60 pF (at 1:1)
Approx 11 pF Approx 9.5 pF
Maximum input
(dc + peak ac)
300 Vpk CAT I
150 Vpk CAT II
500 Vpk CAT I
400 Vpk CAT II
500 Vpk CAT I
400 Vpk CAT II
300 V
CAT I/II
300 V CAT I/II (at 10:1),
150 V CAT I/II (at 1:1)
300 V
CAT I/II
400 V CAT I,
300 V CAT II
Compensation range None 6 to 15 pF 9 to 17 pF 5 to 30 pF 5 to 30 pF (at 10:1) 5 to 30 pF 10 to 25 pF
Probe readout Yes Yes Yes Yes No YES Yes
Cable length 1.5 m 1.5 m 1.5 m 1.2 m 1.3 m 1.3 m 1.2 m
Note 1: 700 MHz BW only available on DSOX/MSOX 4000 X-Series oscilloscopes with 1 GHz or 1.5 GHz bandwidth models
10073D/74D passive probe N2873A/N2894A passive probe with standard
accessories
N2862B/63B passive probe N2889A 10:1/1:1 passive probe N2890A passive probe
Characteristics for Keysight passive probes
07 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
High-voltage Passive
Probes
– Ideal for measuring up to 30 kV
– Up to 500 MHz bandwidth
– 100:1 or 1000:1 attenuation
10076C high-voltage probe
The Keysight 10076C 4 kV 100:1 passive
probe gives you the voltage and
bandwidth you need for making
high-voltage measurements. Its compact
design makes it easier to probe today’s
small power electronics components and
its rugged construction means it can
withstand rough handling without
breaking.
N2771B high-voltage probe
The N2771B is a 1000:1 divider probe for
the measurement of fast high voltage
signals up to 30 kV dc + peak ac, 10 kV
rms.
The probe’s large size and rugged
construction provide superior protection.
The ground lead is fed through the body of
the probe and protrudes behind the safety
barrier, keeping the ground
connection away from the high voltage.
Typical applications include PMTs, motor
drives, high voltage switches, magnatrons,
and modern projection systems.
Characteristics 10076C
Characteristics for N2771B
Ordering information for
Keysight high-voltage probe
Bandwidth 500 MHz (–3 dB)
Risetime (calculated) < 0.7 ns
Attenuation ratio 100:1
Input resistance 66.7 MΩ (when
terminated into 1 MΩ)
Input capacitance Approx 3 pF
Maximum input 4000 Vpk
Compensation 6 to 20 pF
range
Probe readout Yes
Cable length 1.8 m
Bandwidth 50 MHz (–3 dB)
Risetime < 7 ns
Attenuation ratio 1000:1
Input resistance 100 MΩ (when terminated
into 1 MΩ)
Input capacitance 1 pF
Compensation
range
6 to 20 pF
Max. voltage 15 kV dc, 10 kV rms,
30 kV dc + peak ac
Operating
temperature
0 to +50 °C,
80% RH
Storage tempera-
ture
–20 to +70
Dimensions 2 cm (max width of probe
stem after handle) x 33 cm
7.5 cm (max probe width
at probe handle) x 33 cm
10076C High-voltage probe: includes
one retractable hook tip,
one-ground-bayonet, one IC
probing tip, one-alligator ground
lead, one-spring ground tip and a
compensation screwdriver
N2771B High-voltage probe:
includes alligator ground lead,
1-sharp-probe tip
10077A Accessory kit for 10076A/C:
includes one retractable
pincher tip, one ground lead, one
insulation cap, two measuring
pins and two colored tags
N2789A Spring ground tip for 10076B/C
10076C passive probe
N2771B high-voltage probe
10077A accessory kit for 10076A/B
N2771B derating curve
10076C derating curve
08 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
InniiMax Active Probes
and Accessories
1130A-34A InniiMax
high-performance active probe
system
– 1.5 - 7 GHz InniiMax probe system
– InniiMax probe amplier supports
both differential- and single-ended
measurements for a more
cost-effective solution
– Unrivaled InniiMax probing
accessories support browsing,
solder-in, and socketed use models at
the maximum performance available
– Compatible with 3000 X-, 4000 X-,
6000 X-, 5000, 6000, and 7000 Series
oscilloscopes (except for 6000 Series
100-MHz models)
The InniiMax 1130A Series probe
amplier is a perfect complement to the
InniiVision 1 GHz or higher bandwidth
models. Its bandwidth, extremely low
input capacitance (0.32 pF), high
common mode rejection, and patented
resistor probe tip technology provide ultra
low loading of the DUT and superior signal
delity. Keysight’s innovative InniiMax
1130A Series differential probe is the
easiest-to-use, and highest performance
probing system available for high-speed
digital design, and represents a new
industry standard for accuracy, exibility,
and reliability. Designers can achieve full
system bandwidth in conjunction with
InniiVision Series oscilloscopes even
when manually browsing with the probe or
making hands-off measurements.
Optional solder-in probe heads and
solder-in sockets, as well as browser
conguration provide full bandwidth at the
probe tip.
Operating characteristics
Probe bandwidth (–3 dB) 1134A: > 7 GHz
1132A: > 5 GHz
1131A: > 3.5 GHz
1130A: > 1.5 GHz
Rise and fall time
(10 to 90%)
1134A: 60 psec
1132A: 86 psec
1131A: 100 psec
1130A: 233 psec
Input capacitance Cm = 0.1 pF Cm is between tips
Cg = 0.34 pF Cg is ground for each tip
Cdiff = 0.27 pF Differential mode capacitance = Cm + Cg/2
Cse = 0.44 pF Single-ended mode capacitance = Cm + Cg
Input resistance Differential mode resistance = 50 kΩ ± 2%
Single-ended mode resistance = 25 kΩ ± 2%
Input dynamic range ±2.5 V
Input common mode range ±6.75 Vdc to 100 Hz; ±1.25 V > 100 Hz
Maximum signal slew rate 18 V/ns when probing a single-ended signal
30 V/ns when probing a differential signal
DC attenuation 10:1 ± 3% before calibration on oscilloscope
10:1 ± 1% after calibration on oscilloscope
Offset range ±12.0 V when probing single-ended signal
Maximum input voltage 30 Vpeak, CAT I
ESD tolerance > 8 kV from 100 pF, 300 Ω HBM
Maximum number of probes
supported by
3000 X-/5000/6000/7000 Series
2
Maximum number of probes
supported by 4000 X- and 6000
X-Series
4
Keysight 1130A InniiMax probe offers you the highest performance available for measuring differential and
single-ended signals
09 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
InniiMax Active Probes and Accessories (continued)
1130A-34A InniiMax high-performance active probe system
Ordering information for Keysight InniiMax 1130A probe and accessories
Probe amplier
1130A 1.5 GHz InniiMax probe amplier (order one or more probe heads or connectivity kits per amplier)
Connectivity kits
E2669A InniiMax connectivity kit for differential/single-ended measurements
E2668A InniiMax connectivity kit for single-ended measurements
Individual probe heads
E2675A InniiMax differential browser probe head and accessories
E2676A InniiMax single-ended browser probe head and accessories
E2677A InniiMax differential solder-in probe head and accessories
E2678A InniiMax single-ended/differential socketed probe head and accessories
E2679A InniiMax single-ended socketed probe head and accessories
E2695A Differential SMA probe head
N5425A/N5426A 12-GHz differential ZIF solder-in probe head and ZIF probe tips
N5451A InniiMax long-wire ZIF probe tips (for use with N5425A ZIF probe head)
N5450B InniiMax extreme temperature extension cable (that allows for probing in environments from –55 to +150 °C)
N2880A InniiMax in-line attenuator kit (pairs of 6 dB, 12 dB and 20 dB attenuator in a kit)
N2881A InniiMax DC blocking caps (a pair of 30 Vdc blocking cap)
For more comprehensive information about the 1130A InniiMax probe amplier and its accessories, refer to the Keysight Inniium
Osclloscope Probes, Accessories, and Options data sheet with Keysight literature number 5968-7141EN.
InniiMax browser head on board InniiMax ZIF tip soldered on board InniiMax solder-in probe head with long wires
10 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
InniiMode Active Probes
and Accessories
N2750A-52A InniiMode probe
– 1.5 - 6 GHz bandwidth
– Dual attenuation ratio (2:1/10:1)
– InniiMode probing for making
differential, single-ended and
common mode measurements with a
single probe
– Built-in quick action scope control
for quick access to a variety of scope
functions
– Built-in headlight
– Includes solder-in, browser, and
socketed tips standard
– AutoProbe interface for auto
conguration and probe power
N2750A 1.5 GHz InniiMode
differential probe
N2751A 3.5 GHz InniiMode
differential probe
N2752A 6 GHz InniiMode
differential probe
N2776A Differential browser tips
(qty 3)
N2777A InniiMode solder-in tips (qty 3)
N2778A InniiMode socketed tips (qty 3)
N4822A Socketed tip for USB/
Ethernet application xtures
(qty 1)
The N2750A Series InniiMode differential
probe is a new generation of low-cost,
differential active probe compatible with
InniiVision 3000 X-, 4000 X-, 6000
X-Series and Inniium oscilloscope’s
AutoProbe interface.
Measurement versatility
The N2750A Series InniiMode probe offer
2:1 and 10:1 dual attenuation settings,
allowing them to be used for a broad
range of applications. Dual attenuation
range is automatically congured
depending on the size of the input signal.
The new differential probe has an input
resistance of 200 kΩ (differential) or 100
kΩ (each input to ground) and an
extremely low input capacitance of 700 fF
to minimize circuit loading.
This, accompanied with superior signal
delity, makes these probes useful for
most digital design and debug
applications. And with their wide dynamic
range (10 Vpp) and offset range (±15 V),
these probes can be used in a wide variety
of analog signal measurements as well.
InniiMode usability
The N2750A comes with new InniiMode
operation modes. The InniiMode allows
convenient measurements of differential,
single-ended, and common mode signals
with a single probe tip without
reconnecting the probe to change the
connection. The N2750A probe’s
InniiMode provides the following modes
of operation.
– A – B (differential),
– A – ground (single-ended A)
– B – ground (single-ended B)
– (A+B)/2 – ground (common mode)
Quick action scope control
The N2750A Series InniiMode probe
provides convenient and quick access to
various functions on the scope. You often
have a need to control the scope while you
hold a probe in your hand. With the quick
action scope control feature built into the
probe, you can turn the built-in headlight
of the probe on and off, or control some
frequently used scope functions such as
RUN/STOP, auto scale, quick print, quick
save, etc. with only a button press on the
probe. Get control of your most needed
function with a push of the quick action
control button on the probe.
Flexibility in probe use models is also a
vital necessity. The probes come standard
with three different types of exchangeable
probe tips that allow for easy
connections to the circuit under test.
These probe tips enable you to access
multiple signals on anything from header
connectors to hard-to-reach, high-density
circuitry. The probes are equipped with
a white LED headlight to illuminate the
circuit under test which will help you see
where you are probing.
This probe is compatible with InniiVision
3000 X-Series with software ver 2.2 or
above, 4000 X-Series with software ver
3.01 or above, and 6000 X-Series with
software ver. 6.00.
Ordering information for
InniiMode probes and
accessories
Each probe includes two solder-in tips, one
socketed tip and one browser tip.
11 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
InniiMode Active Probes and Accessories (continued)
Characteristics and specications for N2750A Series InniiMode probes
Model number N2750A N2751A N2752A
Probe bandwidth* (–3 dB) 1.5 GHz 3.5 GHz 6 GHz
Rise time, probe only (10-90%) 233 psec 100 psec 58.3 psec
Input resistance (@DC)* 200kΩ ± 2% (differential mode)
100kΩ ± 2% (single-ended mode)
50kΩ ± 2% (common mode)
Input capacitance 700 fF (with browser)
Attenuation ratio (@DC) 2:1 / 10:1
Input dynamic range ±1 V, 2 Vpp (@2:1) / ±5 V, 10 Vpp (@10:1)
Input common mode range ±15 V (from DC to 100 Hz), ±2.5 V (for >100 Hz) ***
Offset range ±15 V
Offset accuracy** < 3%
Maximum non-destructive
Input Voltage
±30 V (DC + peak AC)
Maximum number of probes supported by
3000 X-Series
1
Maximum number of probes supported by
4000 X-Series
4
For more information about the N2750A Series InniiMode probes, refer to the data sheet with the Keysight literature number,
5991-0560EN.
N2750A with browser tip N2750A with socketed tip N2750A with solder-in tip
* Denotes warranted electrical specications at 2:1 attenuation mode after 20 minute warm-up, All others are typical.
** When calibrated on the oscilloscope, these characteristics are determined by the oscilloscope characteristics.
*** Assumes symmetric differential signals.
12 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
High-voltage Differential
Active Probes
– 25 to 800 MHz bandwidth
– Switchable attenuation
– Measure up to 1,400 V CAT II and 7 kV
CAT I
N2790A/91A and N2891A high
voltage differential probes
Oscilloscope users often need to make
oating measurements where neither point
of the measurement is at earth ground.
Use N2790A, N2791A, or N2891A high
voltage differential probes to make safe
and accurate oating measurements with
an oscilloscope. The N2790A, N2791A,
and N2891A high voltage differential
probes allow conventional earth-grounded
Keysight oscilloscope to be used for
oating signal measurements.
Each probe offers user-selectable
attenuation settings that make it highly
versatile, allowing it to be used for a
broad range of applications. The probe
comes with probe tip accessories for use
with small and large components in tight
spaces.
The N2791A and N2891A are
compatible with any oscilloscope with 1
MΩ BNC input. The N2791A and N2891A
probe power is supplied by included 4x AA
batteries or USB host port of the scope or
PC via a supplied USB power cable. The
N2790A is compatible with the Keysight’s
AutoProbe interface where the probe
power is supplied by the Keysight
oscilloscope’s probe interface.
1141A 200 MHz differential
probe
The 1141A is a 1x FET differential probe
with 200-MHz bandwidth and a 3000:1
CMRR. The probe has a high-input
resistance and low-input capacitance of 7
pF to minimize circuit loading. The 1141A
must be used with 1142A probe control
and power module, which controls input
coupling modes dc, dc with variable offset,
and dc reject. Two attenuators, 10x and
100x are provided to expand the linear
differential input range to ±30 V. This
probe works with any 50-Ω input
oscilloscope including 3000 X-, 4000 X-,
5000, 6000X, 6000 300 MHz - 1 GHz, and
7000 Series.
1141A 200-MHz differential probe with 1142A probe
control and power module
N2790A N2791A N2891A
Bandwidth 100 MHz 25 MHz 70 MHz
Risetime 3.5 ns 14 ns 5 ns
Attenuation ratio 50:1 / 500:1 10:1 / 100:1 100:1 / 1000:1
CMRR –80 dB at 50/60 Hz
–50 dB at 1 kHz
-–50 dB at 1 MHz
–80 dB at 50/60 Hz
–40 dB at 1 MHz
–80 dB at 50/60 Hz
–60 dB at 20 kHz
Input impedance
(between inputs)
8 MΩ//3.5 pF 8 MΩ//8 pF 100 MΩ//5 pF
Max input voltage
to ground
±1000 V (CAT II)
±600 V (CAT III)
±700 V at 100:1
±70 V at 10:1
±7000 V at 1000:1
±700 V at 100:1
Max input voltage
between two
inputs
±1400 V at 500:1
±140 V at 50:1
±700 V at 100:1
±70 V at 10:1
±7000 V at 1000:1
±700 V at 100:1
Max number of
probes supported
by 3000 X-/4000
X-/ 5000/6000
/7000 Series
4 4 4
1141A
Bandwidth 200 MHz
Risetime 1.75 ns
Attenuation ratio 1:1 without attenuator,
10:1 and 100:1
with attenuater
CMRR 3000:1 at 1 MHz
10:1 at 100 MHz
Input
impedance
Between inputs:
1 MΩ//7 pF
Max input voltage 200 Vdc + peak ac
(probe alone)
500 Vdc + peak ac
(with attenuator)
Max number
of probes
supported by
3000 X-/4000 X-
/6000 X-
/5000/6000/7000
Series
4
Characteristics for N2790A, N2791A and N2891A differential probe
Characteristics for 1141A
differential probe
13 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
High-voltage Differential Active Probes (continued)
N2804A/N2805A high-voltage high-speed differential probes
The N2804A and N2805A differential probes provide the superior general-purpose
differential signal measurements that are required for high-speed power measurements
such as measuring characteristics of switching power devices, DC-DC converters or
class D ampliers, vehicle bus measurements, and high-speed digital system designs.
The N2804A 300-MHz differential probe offers 100:1 attenuation ratio, allowing it to be
used adequately for high voltage signal measurements. The differential probe has a
differential input resistance of 4 MΩ and low input capacitance of 4 pF to minimize circuit
loading. The probe comes with a pair of extension leads (30 cm long) with a damping
resistor built-in to damp out the in-band resonance and provide at frequency response
even while using the extension leads and probe tip accessories.
The N2805A is a 200-MHz differential probe designed to provide superior differential
signal measurements with long cable length (5 m), making it ideal in an environment
where extended cable length is required. This probe comes with an extensive set of
probe tip accessories for use with small and large components in tight spaces. N2804A 300 MHz differential probe
N2805A 200 MHz differential probe
Characteristics for N2804A and N2805A
N2804A N2805A
Bandwidth 300 MHz (without extension leads)
120 MHz (with extension leads)
200 MHz
Attenuation ratio 100:1 50:1
CMRR -80 dB at 50/60 Hz
-75 dB at 1 MHz
-75 dB at 50/60 Hz
-80 dB at 1 MHz
Input impedance
(between inputs)
4 MΩ // 4 pF 4 MΩ // 4 pF
Max input voltage
(between two inputs)
±300 V (DC+ peak AC) and ±200
Vrms
±200 V (DC+ peak AC) and ±200
Vrms CAT II
Max input voltage ±300 V (DC+ peak AC) and ±200
Vrms CATII
±1000 V (DC+ peak AC) and ±1000
Vrms CATI
±500 V (DC+ peak AC) and ±500
Vrms CAT I
±300 V (DC+ peak AC) and ±200
Vrms CATII
Cable length 1.2 m 5 m
Max number of probes
supported by InniiVision
Series
4 4
Compatible InniiVision
oscilloscopes
4000X Series with software 4.0 or higher, 3000X Series with software
2.38 or higher
For more information about the N7020A power rail probe, check out the Keysight data
sheet with the publication number 5992-0141EN.
14 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
High-voltage Differential Active Probes (continued)
N2792A/N2818A 200-MHz and N2793A/N2819A 800-MHz
general-purpose differential probe
The N2792A/N2818A 200-MHz and N2793A/N2819A 800-MHz differential probes
provide the superior general-purpose differential signal measurements required for
today’s high-speed power measurements, vehicle bus measurements, and digital system
designs.
The N2792A/N2818A and N2793A/N2819A probes offer a 10:1 attenuation setting and
high input resistance and low input capacitance to minimize circuit loading.
The N2792A/93A are compatible with any oscilloscope with 50 Ω BNC input. The probe
can be powered by any USB port on a scope or computer, or by a 9 V battery. The
N2818A/19A are the AutoProbe interface versions of the N2792A/93A. They are
compatible with the InniiVision 3000 X-, 4000 X- and 6000 X-Series only.
Characteristics for N2792A/N2818A and N2793A/N2819A
differential probes
Ordering information for Keysight high voltage differential probes,
power supply and accessories
N2792A/N2818A N2793A/N2819A
Bandwidth 200 MHz 800 MHz
Risetime 1.75 ns 437 ps
Attenuation ratio 10:1 10:1
CMRR 80 dB at 50/60 Hz
–50 dB at 10 MHz
–60 dB at 50/60 Hz
–15 dB at 500 MHz
Input impedance (between inputs) 1 MΩ//3.5 pF 200 kΩ//1 pF
Max input voltage to ground ±60 V ±40 V
Max input voltage between two inputs ±20 V ±15 V
Max number of probes supported by
InniiVision Series
4 4
1141A 200-MHz differential probe
1142A Probe control and power module for 1141A
N2790A 100-MHz, 1.4 kV differential probe with AutoProbe interface
N2791A 25-MHz, 700-V differential probe
N2792A 200-MHz, 20-V differential probe
N2818A 200-MHz, 20-V differential probe with AutoProbe interface
N2793A 800-MHz, 15-V differential probe
N2819A 800-MHz, 15-V differential probe with AutoProbe interface
N2891A 70-MHz, 7,000-V differential probe
N4853A Variable pitch browser for N2793A/N2819A, qty 2
N4854A DC blocking capacitor for N2793A/N2819A, qty 2
N2804A 300 MHz high voltage differential probe
N2805A 200 MHz high voltage differential probe with extended cable length
N2816A Probe tip accessory kit for N2804A including 2 each alligator clips, 2 each pincer
clips, and 2 each extension leads (30 cm)
N2817A Probe tip accessory kit for N2805A including 2 each alligator clips, 2 each hook
clips, 2 each pincer clips, and 2 each browser tips
N2790A 100-MHz, 1.4-kV differential probe with
AutoProbe interface
N2791A 25-MHz, 700-V differential probe
N2792A 200-MHz, 20-V differential probe
N2793A 800-MHz, 15-V differential probe
15 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
Model number N2795A N2796A N2797A
Probe bandwidth* (–3 dB) 1 GHz 2 GHz 1.5 GHz
Risetime 350 ps 175 ps 233 psec
System bandwidth 500/600 MHz with
Keysight’s 500/600 MHz
InniiVision/Inniium,
1 GHz with 1 GHz
InniiVision 3000 X, 4000 X
1 GHz with Keysight’s
1 GHz InniiVision/Inniium, 1.5 GHz
with Keysight’s 1.5 GHz InniiVision
4000 X,
6000 X
Attenuation ratio (at dc) 10:1 ± 0.5%
Input dynamic range –8 to +8 V (DC or peak AC)
Non-destructive input voltage –20 to +20 V
Offset range ±8 V ±12 V
DC offset error (output zero) ±1 mV
Low frequency accuracy 0.5% at 70 Hz, 1 Vpp
Input resistance* 1 MΩ
Input capacitance 1 pF
Output impedance 50 Ω
Max number of probes
supported by InniiVision 3000
X-/5000/6000/7000 Series**
2
Max number of probes
supported by InniiVision
4000X, 6000X
4
* Denotes warranted electrical specications after 20 minute warm-up, all others are typical
** The N2797A is compatible with 3000 X-, 4000 X- and 6000 X-Series only.
N4839A Dual lead socketed adapter, 6 cm, qty 2
N4840A Dual lead solder-in adapter, 5 cm, qty 2
N4841A Dual lead socketed adapter, 9 cm, qty 2
N4842A Dual pin PCB header, qty 2
N4843A Solderable tips, qty 10
N4844A Right angle ground lead, 5 cm, qty 2
N4845A Ground blade, qty 2
N4846A Offset ground, qty 2
Single-ended Active
Probes
N2795A/96A/97A low-cost
single-ended active voltage
– High resistance (1MΩ) and low
capacitance (1 pF) input for low
loading
– Wide input dynamic range (±8 V) and
offset range (±12 V for N2796A/97A,
±8 V for N2795A)
– Built-in headlight
– Direct connection to AutoProbe
interface (no power supply required)
– N2797A for extreme temperature
environmental chamber testing at –40
to +85 °C
The N2795A/96A are a new generation of
low-cost, 1 to 2 GHz single-ended active
probes with the AutoProbe interface
(compatible with Keysight’s InniVision
and Inniium family of oscilloscopes).
These probes integrate many of the
characteristics needed for today’s
general-purpose, high-speed
probing–especially in digital system
design, component design/
characterization, and educational research
applications. Its 1 MΩ input resistance and
extremely low input capacitance (1 pF)
provide ultra low loading of the DUT. This,
accompanied with superior signal delity,
makes these probes useful for most of
today’s digital logic voltages. Testing
devices over extreme temperature ranges
is quite common these days. The N2797A
1.5 GHz single-ended active probe is the
industry’s rst low-cost high input
impedance active probe with rugged
probe tips for environmental chamber
testing of ICs and devices. It gives the
ability to probe signals at drastic
temperature swings ranging from –40 to
+85 °C. The probe provides a 2 m long
cable. Order N2798A for re-ordering
accessories.
The N2795A/96A/97A are equipped with
a white LED headlight to illuminate the
circuit under test. The probes are powered
directly by the InniiVision and Inniium
Autoprobe interface, eliminating the need
for an additional power supply. The probes
also come with a number of accessories
that allow for easy connections to the
circuit under test.
For more information about N2795A/96A/97A active probe, refer to the Keysight
N2795A/96A/97A active probe data sheet, literature number 5990-6480EN.
Replacement accessories
16 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
Single-ended Active Probes (continued) N7020A
power rail probe
– 2-GHz single-ended active probe for power rail noise measurement
– 1:1 attenuation ratio ensures low noise signal measurement
– ±24V of probe offset range enables effective elimination of DC component of a
power supply.
The N7020A power rail probe is a low noise, large offset range oscilloscope probe that
enables users to measure small signals riding on top of DC power rails.
– Low noise: The N7020A power rail probe is a 1:1 attenuation ratio active probe. As
a general rule, the higher a probes attenuation ratio, the nosier the signal will be on
the oscilloscope.
– Large offset range: The N7020A power rail probe provides ±24V of probe offset. This
enables users to center the signal on screen while placing the oscilloscope at its
maximum vertical sensitivity and zoom in on the signal.
– Low DC loading: The N7020A power rail probe has 50 kΩ input impedance at DC,
minimizing the probe’s DC loading of the power rail.
– Large input dynamic range: The N7020A power rail probe’s ±850 mV input dynamic
range means that users can measure up to ±850 mV deviations of their DC supplies.
This is very useful for measuring programmable supplies like those used in micro-
controller power saving modes.
Characteristics and specications
Probe bandwidth (-3dB) 2 GHz
Attenuation ratio 1:1
Offset range ±24 V
Input impedance at DC 50 kΩ
At >1 MHz 50 Ω
Input dynamic range ± 850 mV
Probe noise 10% of oscilloscope noise
Included accessories N7021A coaxial probe head (qty. 3), N7022A SMA main cable
Max number of probes supported
by InniiVision
4
Compatible InniiVision
oscilloscopes
4000 X-Series with software rev 4.0 or higher
For more information about the N7020A power rail probe, check out the Keysight data
sheet with the publication number 5992-0141EN.
17 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
Input impedance 100 kΩ
Input capacitance 8 pF
N2756A 16-ch MSO cable kit for 6000
X-Series MSO
N6450-60001 Logic probe with 2 x 8 ying
leads. Includes 20 IC clips and
5 ground extension leads
N6459-60001 Logic probe with 1 x 8
ying leads. Includes 10 IC
clips and 3 ground extension
leads
01650-61607 40-pin (F) to 40-pin (F) logic
probe cable
Input impedance 100 kΩ
Input capacitance 12 pF
Characteristics for Keysight
54620-68701, N6450-60001,
N6459-60001 logic probes
Ordering information for Keysight
logic probes
Characteristics for Keysight
01650-61607 logic probe
Mixed Signal Oscilloscope
Logic Probes
– Compatible with all 40-pin logic probe
– Flying leads offer exibility and
convenience
MSO probes offer great value
and performance
These logic probes for the InniiVision
mixed signal oscilloscopes (MSOs) are the
same ones used with Keysight industry-
leading high-performance logic analyzers.
This means we can offer the best
performance, great value and access to
the industry’s broadest range of logic
probing accessories.
The N6450-60001 2 x 8-signal logic
probes are divided into two sets of eight
channels so you can probe pins that are
far apart and work conveniently with only
one set if that’s all you require. For optimal
signal delity, connect ground at each
logic probe, in addition to taking a
common ground to all eight signals via a
separate ground connector on the probe
pod. The N6450-60001 probe is included
with 6000, 7000, 3000 X- and 4000
X-Series MSOs.
The N6459-60001 is an 8-channel MSO
logic probe designed to work with the
2000 X-Series MSOs.
The N2756A is the 16-ch MSO cable kit
that comes with the 6000 X-Series MSOs.
The 01650-61607 is the 40-pin (F) to
40-pin (F) logic probe cable for Keysight’s
InniiVision and 54600 Series MSOs. This
cable gives the MSO the standard 40-pin
female input connector that many Keysight
logic analyzers have. With this cable, a
user can connect a wide variety of logic
analyzer probes such as Mictor, Samtec,
and Soft Touch probes.
01650-61607 logic probe
N2756A 16-ch MSO cable kitn
N6450-60001
18 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
Mixed Signal Oscilloscope Logic Probes (continued)
The InniiVision MSO digital channels were architected to be compatible with a wide
variety of probing accessories developed over 20 years for logic analyzers. There’s a
good chance that the logic analyzer accessories you already own work with your MSO.
With the addition of an optional 40-pin cable, 01650-61607, the MSO accepts numerous
logic analyzer accessories:
– E5346A 34-channel Mictor connector probe
– E5385A 34-channel Samtec connector
– E5383A 16-channel ying lead set
– 01650-63203 16-channel termination adaptor (also available as a bundle of both the
termination adapter and the 40-pin cable with PN 10085-68701)
– E5404A 34-channel soft touch pro connectorless probe
– E5394A 34-channel soft touch connectorless probe
– E5396A 16-channel soft touch connectorless probe
– Any other accessory that connects to a logic analyzer via a 40-pin cable
For logic accessories of greater channel width than MSO digital channels (> 16 channels),
there are two use models.
– Route up to 16 signals to the probe and don’t use the additional probe channels.
– Route up to 32 signals to the probe and measure 1/2 of them at a time. Simply plug
the 40-pin cable to the other side of the probe to see the other 1/2 of the signals. E5396A 16-channel soft touch connectorless probe
E5346A 34-channel Mictor connector probe E5385A 34-channel Samtec connector probe
19 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
Clamp-on Current Probes
– Up to 100 MHz bandwidth and 500
Arms current
– Hybrid technology to measure ac and
dc
– Compatible with 1 MΩ scope input
Accurate current measurements
without breaking the circuit
Compatible with any scope or voltage
measuring instruments with BNC input,
the 1146B and N2780B Series current
probes offer accurate and reliable
solutions for measuring dc and ac
currents. The probes use a hybrid
technology that includes a Hall effect
sensor, which senses the dc current and a
current transformer, which senses the ac
current, making it unnecessary to make an
electrical connection to the circuit.
1146B 100 kHz current probe
The 1146B ac/dc current probe provides
accurate display and measurement of
currents from 100 mA to 100 Arms, dc to
100 kHz, without breaking into the circuit.
A battery level indicator and overload
indicator help ensure proper readings. It
connects directly to the scope through a
2-m coaxial cable with an insulated BNC.
1147B/N2893A 50-MHz/
100-MHz current probe with
AutoProbe interface
The 1147B/N2893A is a wide bandwidth,
dc to 50-MHz/100-MHz current probe.
The probe offers at frequency response
across the entire dc to 50-MHz/100-MHz
bandwidth, low noise (< –2.5 mArms) and
low circuit insertion loss.
The 1147B/N2893A probe is compatible
with the AutoProbe interface, which
completely congures the oscilloscope
for the probe when used with the 3000
X-, 4000 X-, 5000, 6000 300 MHz - 1
GHz, 7000 Series scopes. Probe power is
provided by the scope, so there is no need
for an external power supply. The N2893A
uniquely provides auto demagnetization
and offset elimination feature when used
in conjuction with InniiVision or Inniium
scopes.
N2780B/81B/82B/83B/83L
2-MHz/10-MHz/50-MHz/
100-MHz current probe
The N2780B Series current probes are
high bandwidth, active current probes,
featuring at bandwidth, low noise (2.5
mArms) and low circuit insertion loss. In
conjunction with the power supply (model
N2779A), this probe can be used with any
oscilloscope having a high-impedance
BNC input. The companion power supply
N2779A (3 x 12 Vdc output) lets you
connect up to any three N2780B-83B
current probes to a single power supply.
The N2783L 80 MHz current probe
offers 5 m long cable, which allows you to
reach DUTs in long distances very easily.
Other than the bandwidth performance,
the N2783A and N2783L have the same
electrical performance. The N2783L also
requires the N2779A power supply to
power the probe.
1147B 50-MHz current probe with AutoProbe
interface
1146B 100-kHz current probe
N2893A 100-MHz current probe with AutoProbe
interface
N2780B Series current probes with N2779A power supply
20 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
Bandwidth* dc to 100 kHz (–3 dB)
Current range* 100 mV/A:100 mA to
10 A peak
10 mV/A:1 to 100 A peak
Output signal 1000 mV peak max
AC current
accuracy*
Range 100 mV/A
(50 mA to 10 A peak)
Accuracy
Range
3% of reading ±50 mA
10 mV/A
(500 mA to 40 A peak)
Accuracy
Range
4% of reading ±50 mA
10 mV/A
(40 A to 100 A peak)
Accuracy (40 A to 100 A peak)
15% max at 100 A
Noise Range 10 mV/A: 480 μV
Range 100 mV/A: 3 mV
Insertion impedance 0.01 Ω (50/60 Hz)
Maximum working
voltage
600 Vrms CAT II or
300 Vrms CAT III
Maximum common
mode voltage
600 Vrms CAT II or
300 Vrms CAT III
Inuence of adjacent
conductor
< 0.2 mA/A AC
Inuence of
conductor position
< 0.2 mA/A AC
Battery 9 V alkaline (NEDA
1604A, IEC 6LR61)
Low battery Green LED on when
≤ 6.5 V
Battery life 55 hours typical
Bandwidth
(–3 dB)
dc to 50 MHz (1147B)
dc to 100 MHz (N2893A)
Risetime 7 ns or less (1147B), 3.5 ns
or less (N2893A)
Maximum
current
(continuous)
15 A peak, 15 A DC,
10 Arms (when two probes
are used with InniiVision
scope)
30A peak, 30 A DC, 24 Arms
(when one probe is used
with InniiVision 3000X,
5000/6000/7000 scope)
Maximum peak
current
(non-continuous)
30 A peak (when two probes
are used with InniiVision
scope) 32 A peak (when one
probe is used with
InniiVision scope)
Output voltage
rate
0.1 V/A
Amplitude
accuracy
±1% rdg, ±10 mA (dc and 45
to 66 Hz, rated current)
Noise Equivalent to 2.5 mArms or
less (for 20 MHz bandwidth
measuring instrument)
Temperature
coefcient for
sensitivity
±2% or less (within a range
of 0 to 40 °C or 32 to 104 °F)
Effect of
external
magnetic elds
Equivalent to a
maximum of 20 mA (in a dc
to 60 Hz, 400 A/m magnetic
eld)
Maximum rated
power
3 VA (with rated
current)
Maximum input
voltage
300 V CAT I
Diameter of
measurable
:conductors
5 mm dia. (0.2 in dia.)
Probe interface AutoProbe interface
Cable lengths Sensor cable:
Appox. 1.5 m (59.0n in)
Power supply cable:
Appox. 1 m (39.4 in)
Maximum
number of
probes
supported
2
Bandwidth (–3 dB) dc to 2 MHz (N2780B)
dc to 10 MHz (N2781B)
dc to 50 MHz (N2782B)
dc to 80 MHz (N2783L)
dc to 100 MHz (N2783A)
Maximum current
(continuous)
500 A (N2780B)
150 A (N2781B)
30 A (N2782B/83B/83L)
Maximum peak
current (non-
continuous)
700 A peak (N2780B)
300 A peak (N2781B)
50 A peak
(N2782B/83B/83L)
Maximum input
voltage
300 V CAT I
(N2782B/83B/83L)
300 V CAT III, 600 V
CAT II (N2780B/81B)
Output voltage rate 0.01 V/A
(N2780B/81B)
0.1 V/A
(N2782B/83B/83L)
Amplitude accuracy ±1.0 % rdg ±500 mA
(N2780B)
±1.0 % rdg ±100 mA
(N2781B)
±1.0 % rdg ±10 mA
( N2782B)
±1.0 % rdg ±10 mA
(N2783B/83L)
1146B 100-kHz current probe
1147B 50-MHz current probe with
AutoProbe interface
N2893A 100-MHz current probe with
AutoProbe interface
N2780B 2-MHz current probe
N2781B 10-MHz current probe
N2782B 50-MHz current probe
N2783L 80-MHz current probe with
5 m long cable
N2783B 100-MHz current probe
N2779A 3-channel power supply for
N2780B/81B/82B/83B/83L
Clamp-on Current Probes (continued)
Characteristics of the 1146B
current probe
Characteristics of the 1147B/
N2893A current probe
Characteristics of N2780B
Series current probes
Ordering information for
Keysight current probes
Note: Reference conditions 23 ±5 °C,
(73.4 ±41 °C) 20 to 75% relative humidity, dc to 1
kHz, probe zeroed, 1-minute warmup, batteries at
9 V + 0.1 V, external magnetic eld <40 A/m, no dc
component, no external current carrying
conductor, 1 MΩ/100 pF load, conductor centered
in jaw.
* Characteristics marked with asterisks are
specied performance. Others are typical
characteristics.
For more information about the N2780B
Series current probes, refer to the Keysight
N2780B Series current probe data sheet,
literature number 5989-6432EN.
Note: The above specications are guaranteed at
23 ±3 °C (or 73 ±5 °F)
21 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
High-Sensitivity Current
Probes
– Measure AC/DC currents as low as
50 uA
– Ideal for capturing and analyzing low
level current ow in the DUT to
characterize sub-circuits or measure
current consumption of battery-
powered devices or integrated circuits
– Simultaneous high- and low-gain
views of the current waveform for
more precise wide dynamic range
measurement (with N2820A)
As modern battery-powered devices and
integrated circuits become more green
and energy efcient, there is a growing
need to make high-sensitivity,
low-level current measurements to ensure
the current consumption of these devices
is in acceptable limits. The N2820A
high-sensitivity probe is engineered to
make high-dynamic-range, high-
sensitivity measurements to meet today’s
challenging current measurement needs.
The ultra-sensitive N2820A AC/DC current
probe can support measurements from 50
uA to 5 A on Keysight oscilloscopes. The
N2820A interface uses a make-before-
break (MBB) connector, allowing you to
quickly probe multiple locations on your
DUT without having to solder or unsolder
the leads. The N2820A 2-channel current
probe connects to two oscilloscope
channels to provide simultaneous low-and
high-gain views for wider dynamic range
measurement, while the N2821A
1-channel current probe provides one
user-selectable view at a time.
The N2820A 2-channel current probe connects to two oscilloscope channels to provide simultaneous low- and
high-gain views for wider dynamic range measurement
Use an area-under-the-curve
measurement (Charge) on InniiVision
oscilloscopes to easily calculate the
integrated current consumptions over time
in Ah.
The N2820A/21A high-sensitivity current
probes are compatible with InniiVision
3000 X-, 4000 X- and 6000 X-Series
oscilloscopes.
22 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
Probe characteristics and specication
Bandwidth (–3 dB) Zoom-out channel: DC to 3 MHz
Zoom-in channel: DC to 500 kHz
Risetime (Tr = 0.35/bandwidth, 10% - 90%) Zoom-out channel: < 0.116 μsec
Zoom-in channel: < 0.7 μsec
Minimum measurable current* 250 μA (with N2822A 20 mΩ, 500 mW)
50 μA (with N2824A 100 mΩ, 500 mW)
5 mA (with N2825A user-dened 1 mΩ, 500 mW)
50 μA (with N2825A user-dened 1 kΩ, 500 mW)
Maximum measurable current 5 A (with N2822A 20 mΩ, 500 mW)
2.2 A (with N2824A 100 mΩ, 500 mW)
5 A** (with N2825A user-dened 1 mΩ, 500 mW)
1.2 mA** (with N2825A user-dened 1 kΩ, 500 mW)
DC amplitude accuracy ± 3% or 10 μA (whichever is greater)
Gain*** Zoom-in channel: 300 ± 3%
Zoom-out channel: 1.97 ± 3%
Max input voltage ± 12 V
Output impedance 1 MΩ
Standard accessories – 1 each 20 mΩ resistor sensor head
– 1 each 100 mΩ resistor sensor head
– 1 each user dened resistor sensor head
– 5 each twisted leads (22 AWG) with sockets
– 5 each twisted leads (22 AWG) without sockets
– 5 each MBB headers
– 5 each MBB receptacles
– 1 each ground lead
– 1 each screw driver
– 1 each passive cable (with N2820A only)
– 1 each user guide manual (English)
Compatible InniiVision oscilloscopes InniiVision 3000 X-Series (with software version 2.30 or higher)
InniiVision 4000 X-Series (with software version 3.10 or higher)
InniiVision 6000 X-Series (with software version 6.00 or higher)
Max number of probes supported by 3000 X-Series Two N2820A probes using both pods or two N2821A probes
Max number of probes supported by 4000 X-Series Two N2820A probes using both pods, four N2820A probes using only the primary pod, or
four N2821A probes
Model numbers Descriptions
N2820A High-sensitivity 2-ch current probe
N2821A High-sensitivity 1-ch current probe
Replacement part numbers
N2822A 20 mΩ resistor tips
N2824A 100 mΩ resistor tips
N2825A User-dened resistor tips
N2826A Replacement wires (15.5 cm, 22 AWG bare wires) (qty 5)
N2827A Passive cable (for N2820A secondary channel)
N2828A Replacement MBB (Make Before Break) headers (qty 5)
N2829A Replacement MBB (Make Before Break) receptacles and 15.5 cm, AWG 22 socketed wires (qty 5 each)
High-Sensitivity Current Probes (continued)
* Vsupply is equal to 5 V, solder attached.
** Max current varies with max resistor power rating. The examples in the table assume 500 mW power rating.
*** Denotes warrantied specication after 20-minute warm up. All others entries in the table are characteristics
Ordering information for Keysight current probes
23 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
Wedge Probe Adapters
Easy connection to surface
mount ICs
Safe, with no chance of shorting
Mechanically non-invasive contact
3-, 8-, and 16-signal versions
Supports 0.5 and 0.65-mm
TQFP and PQFP packages
Problem-free probing
The Keysight wedge probe adapter
eliminates many of the frustrations
associated with probing surface mount
components. If you’ve ever accidentally
shorted IC pins together, experienced
electrical and/or mechanical problems
with soldering small wires onto leads, or
gotten frustrated juggling multiple probes
while you’re trying to operate your scope,
the Wedge was designed with you in mind.
Make the inaccessible accessible
When you use the Wedge, you don’t have
to worry about shorting IC pins together
on a delicate component–or worse yet on
an irreplaceable prototype. The Wedge
is easy to insert and it stays put. There’s
no need to solder small wires onto leads.
The Wedge is mechanically non-invasive,
so you won’t damage the legs of the IC.
Instead, you’ll have easy access to
hard-to-reach components.
Electrical reliability
The Wedge makes two contact points with
each leg of the IC. This redundant physical
connection increases the electrical
reliability of the connection. And the
Wedge’s low capacitance and inductance
provides superior performance to many
other alternatives.
The wedge probe adapter connects
directly to 1145A/1155A active probes
and the dual lead adapter provided with
the 1160A-65A passive probe family and
N2877A/N2879A accessory kits for use
with N287xA Series passive probes.
IC clip kits
An inexpensive solution for probing
ne-pitch ICs, the 10072A SMT Kit
includes 10 IC clips and 2 dual-lead
adapters that connect the clips directly to
10070-family probes.
The 10075A 0.5-mm IC clip kit is ideal
for connecting to IC’s as ne as 0.5 mm.
The clip body allows many clips to be
mounted side-by-side. The kit includes
four 0.5-mm IC clips and two dual-lead
adapters that connect the IC clips directly
to 10070-family probes.
Keysight Wedge electrical
characteristics
Operating
voltage
< 40 Vdc + peak ac
Operating
current
0.5 A maximum
Capacitance
between
contacts
2 pF typical (all except
Keysight-E2643A/44A)
4.33 pF typical at 1 MHz
(Keysight-E2643A/44A)
Self-
inductance
15 nH typical (all except Keysight
E2643A/44A)
37 nH typical at 1 MHz
(Keysight E2642A/44A)
Cross
coupling
–31 dB typical at 100 MHz
(Keysight E2643A/44A)
Contact
resistance
< 0.1 Ω
E2613A 0.5 mm Wedge probe adapter,
3 signal, qty 1
E2614A 0.5 mm Wedge probe adapter,
8 signal, qty 1
E2643A 0.5 mm Wedge probe adapter,
16 signal, qty 1
E2615A 0.65 mm Wedge probe adapter,
3 signal, qty 1
E2616A 0.65 mm Wedge probe adapter,
8 signal, qty 1
E2644A 0.65 mm Wedge probe adapter,
16 signal, qty 1
10072A SMT kit for 10070 probe family
10075A 0.5 mm IC clip kit
Ordering information
24 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
Testmobile
The sturdy Keysight 1180CZ Testmobile for
use with 6000 Series oscilloscopes makes
sharing your scope easy. Its large wheels
make it easy to roll from place to place.
For use with the Keysight 6000 Series
scope, the 1180CZ Testmobile scope cart
with the N2919A bracket provides
convenient mobility and secure mounting
of your scope.
Specications for the Keysight
Testmobiles
Miscellaneous Accessories
1180CZ
Total load
capacity
59 kg (130 lbs)
Tilt tray 45.7 cm wide x
45.7 cm deep
(18 in Wide x 18 in Deep)
Carrying cases
The Keysight N6457A soft carrying case
makes transporting and shipping your
2000 X- and 3000 X-Series oscilloscope
safe and simple. An oscilloscope and other
accessories t neatly inside the padded
shell for shipment. For use with the 7000,
4000 X-, and 6000 X-Series, order
N2733B soft carrying case.
Rackmount kit
The Keysight N2916B rackmount kit
positions your 5000 and 6000 Series
scope in the center of the rack. Each kit
includes a custom shelf with rails, 6 BNC
pass-throughs and all necessary screws.
For mounting the 7000 Series in the rack,
order N2732A. For mounting all 2000
X- and 3000 X-Series in a rack, order
N6456A.For mounting any 4000 X-Series
in a rack, order N2763A. For mounting a
6000 X-Series in a rack, order the N2111A.
1180CZ Testmobile for 6000 Series
N2919A Bracket for 1180CZ
Testmobile and 6000 Series
scope
N2917B Hard carrying case for 5000 and
6000 Series
N6457A Soft carrying case for
2000 X- and 3000 X-Series
N2733B Soft carrying case for
7000, 4000 X- and 6000 X-
Series
N2760A Soft carrying case for 5000
Series
N2916B Rackmount kit for 5000 and
6000 Series
N2732A Rackmount kit for 7000 Series
N6456A Rackmount kit for 2000 and
3000 X-Series
N2763A Rackmount kit for
4000 X- Series
N2111A Rack mount kit for 6000 X-Series
Ordering information
N2760A soft carrying case for the 5000 Series
N2733B soft carrying case for 7000, 4000 X-, and
6000 X-Series
N2916B rackmount kit for 5000/6000 Series
25 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
Product number Description
N2784A11-arm probe positioner
N2785A12-arm probe positioner
N2786A 2-leg probe positioner
N2787A 3D probe positioner
Ordering information
Miscellaneous Accessories (continued)
Probe positioners
– Easy-to-manipulate probe arms for
hands-free browsing
– One- or two-articulated arms with
stable high-mass base (N2784A and
N2785A)
– Quick and stable XY positioning
(N2786A)
– Stable 3D probe positioning for
hard-to-reach XYZ access (N2787A)
– Compatible with most scope probes
– Applications: Hands-free browsing for
electronic components on PC board
The N2784A and N2785A probe
positioners provide quick and stable X-Y
positioning for PC boards and devices that
require hands-free probing.
Unlike other probe positioners that require
multiple adjustments to lock the probe
holder into position, the N2784A and
N2785A need only the “lift and drop”
motion to put the probe in place. The
weight stabilization technique used in
these probe holders keeps constant
pressure at the probing point so the probe
tip stays in position even when the target
board is bumped.
The N2786A is a low cost, easy-to-use
XY axis probe holder for general purpose
probing appliactions. The two-leffed
positioner is designed to be easy to use–
the positioner itself has no controls to
positioner it in place.
The N2787A is a 3D probe positioner with
a exible, articulating arm that can be
quickly positioned in a variety of
congurations.
For more information about Keysight’s
probe positioners, refer to literature
number 5989-9131EN.
1. Includes 3x magnifying glass, arm strap, cable
tie, probe rest, and manual.
N2784A one-arm probe positioner
N2786A 2-leg probe positioner N2787A 3D probe positioner
26 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
N2744A T2A Probe Interface Adapter
– Enables Tektronix® TekProbe-BNC®
level 2 probes to connect to Keysight’s
AutoProbe interface on InniiVision
3000 X-, 4000 X-, 6000 X-, 5000,
6000, and 7000 oscilloscopes
– An easy-to-use plug-on adapter to
the Keysight oscilloscope’s AutoProbe
interface
– Provides necessary probe power,
calibration, and offset control as
needed to the attached TekProbe
probe
The N2744A T2A interface adapter
enables selected TekProbe® interface
level 2 probes to be used with Keysight
oscilloscopes with AutoProbe interface.
Existing TekProbe-BNC probe types can
simply be plugged into the T2A adapter
which is then plugged directly into any
AutoProbe input channel on an InniiVision
or Inniium oscilloscope. Select the probe
model in the scope menu and the Keysight
oscilloscope sets up the attenuation factor
and the probe type automatically. The T2A
interface adapter supplies the necessary
probe power, calibration (for selected
models only) and offset control as used by
the connected TekProbe probe. The
adapter is targeted for customers using
both Tek active probes with TekProbe-BNC
level 2 interfaces and Keysight
oscilloscopes with the AutoProbe
interface.
Tek probe compatibility
The N2744A T2A adapter supports only
the probes listed below with TekProbe
interfaces.
TCP202 50-MHz AC/DC current probe
P6243 Single-ended active probe, 1
GHz, 10:1 without offset control
P6245 Single-ended active probe,
1.5 GHz, 10:1 with offset control
P6205 Single-ended active probe, 750
MHz, 10:1 without offset control
P6241 Single-ended active probe,
4 GHz, 10:1 with offset control
P6249 Single-ended active probe,
4 GHz, 5:1 with offset control
P6701B 1 GHz Optical-to-electrical
converter with FC/PC connector
P6703B 1.2 GHz Optical-to-electrical
converter with FC/PC connector
P6711 250 MHz Optical-to-electrical
converter
P6713 300 MHz Optical-to-electrical
converter
P5205 or
P5205A
Differential probe, 100 MHz,
50:1/500:1 with offset control
P5210 or
P5210A
Differential probe, 50 MHz,
100:1/1000:1 with offset control
P6246 400 MHz, 10:1/1:1 with offset
control
P6247 1 GHz, 10:1/1:1 with offset control
P6248 1.5 GHz, 10:1/1:1 with offset control
P6250 500 MHz, 50:1/5:1 with offset
control
P6251 1 GHz, 50:1/5:1 with offset control
AC/DC current probe
Single-ended active probes
Differential active probes
Keysight scope compatibility
– Keysight InniiVision 6000 X-Series
with sofware version 6.00 or higher
– Keysight InniiVision 3000 X-/4000
X-Series with software version 1.10 or
higher
– Keysight InniiVision 5000, 6000,
and 7000 Series and future revisions
(except 6000 100-MHz) with software
version 06.16 or higher
Optical-to-Electrical Converters
(works with InniiVision 5000,
6000 and 7000 with version 6.16
software only)
N2744A T2A probe interface adapter
Ordering information
27 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
Applications Speed and signal type Recommended probe Required probe bandwidth
LIN 10 kHz, single-ended SE passive > 100 MHz
ARINC 425 1000 kbps, differential N2792A/N2818A 200 MHz
CAN 1 Mbps, differential N2792A/N2818A 200 MHz
MIL-S TD 15 53 1 Mbps, differential
±25 Vpp
N2792A/N2818A 200 MHz
I²S (audio) ~2.8 MHz, single-ended SE passive > 100 MHz
I²C/SMbus < 4 MHz, single-ended SE passive > 100 MHz
RS232/UART < 10 Mbps, single-ended SE passive > 100 MHz
RS422/485 10 Mbps, differential N2792A/N2818A 200 MHz
FlexRay 10 Mbps, differential N2792A/N2818A 200 MHz
SPI 1 – 100 MHz, single-ended SE passive or N2795A > 100 MHz passive or 1 GHz active
MOST 150 Mbps, differential N2750A 1.5 GHz
USB 2.0 480 Mbps, differential N2750A 1.5 GHz
Recommended Probes for Low-/Mid-Speed Bus Measurements
28 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
Keysight Oscilloscopes
Multiple form factors from 20 MHz to > 90 GHz | Industry leading specs | Powerful applications
myKeysight
www.keysight.com/find/mykeysight
A personalized view into the information most relevant to you.
www.axiestandard.org
AdvancedTCA® Extensions for Instrumentation and Test (AXIe) is an
open standard that extends the AdvancedTCA for general purpose and
semiconductor test. Keysight is a founding member of the AXIe consortium.
ATCA®, AdvancedTCA®, and the ATCA logo are registered US trademarks of
the PCI Industrial Computer Manufacturers Group.
www.lxistandard.org
LAN eXtensions for Instruments puts the power of Ethernet and the
Web inside your test systems. Keysight is a founding member of the LXI
consortium.
www.pxisa.org
PCI eXtensions for Instrumentation (PXI) modular instrumentation delivers a
rugged, PC-based high-performance measurement and automation system.
Three-Year Warranty
www.keysight.com/find/ThreeYearWarranty
Keysight’s commitment to superior product quality and lower total cost
of ownership. The only test and measurement company with three-year
warranty standard on all instruments, worldwide.
Keysight Assurance Plans
www.keysight.com/find/AssurancePlans
Up to five years of protection and no budgetary surprises to ensure your
instruments are operating to specification so you can rely on accurate
measurements.
www.keysight.com/go/quality
Keysight Technologies, Inc.
DEKRA Certified ISO 9001:2008
Quality Management System
Keysight Channel Partners
www.keysight.com/find/channelpartners
Get the best of both worlds: Keysight’s measurement expertise and product
breadth, combined with channel partner convenience.
TekProbe®, TEKTRONIX® and TEK® are registered trademarks of Tektronix, Inc
www.keysight.com/find/probes
29 | Keysight | InniiVision Oscilloscope Probes and Accessories - Data Sheet
This information is subject to change without notice.
© Keysight Technologies, 2012 - 2014
Published in USA, December 10, 2014
5968-8153EN
www.keysight.com
For more information on Keysight
Technologies’ products, applications or
services, please contact your local Keysight
office. The complete list is available at:
www.keysight.com/find/contactus
Americas
Canada (877) 894 4414
Brazil 55 11 3351 7010
Mexico 001 800 254 2440
United States (800) 829 4444
Asia Pacic
Australia 1 800 629 485
China 800 810 0189
Hong Kong 800 938 693
India 1 800 112 929
Japan 0120 (421) 345
Korea 080 769 0800
Malaysia 1 800 888 848
Singapore 1 800 375 8100
Taiwan 0800 047 866
Other AP Countries (65) 6375 8100
Europe & Middle East
Austria 0800 001122
Belgium 0800 58580
Finland 0800 523252
France 0805 980333
Germany 0800 6270999
Ireland 1800 832700
Israel 1 809 343051
Italy 800 599100
Luxembourg +32 800 58580
Netherlands 0800 0233200
Russia 8800 5009286
Spain 800 000154
Sweden 0200 882255
Switzerland 0800 805353
Opt. 1 (DE)
Opt. 2 (FR)
Opt. 3 (IT)
United Kingdom 0800 0260637
For other unlisted countries:
www.keysight.com/find/contactus
(BP-09-23-14)