Product Specification RoHS-6 Compliant 10GBASE-LR X2 Transponder FTLX1442E2/FTLX1442F2 PRODUCT FEATURES Hot pluggable X2 MSA form factor Total power consumption: 3.5 W maximum RoHS-6 compliant (lead-free) Temperature range 0C to 70C Transmission distance of 10km Uncooled directly modulated Distributed Feedback (DFB) laser at 1310 nm SC connector, single mode fiber Full duplex transmission mode Digital Optics Monitoring (DOM) Power supply: +5.0 V, +3.3 V, Adaptable Power Supply (APS: +1.2 V) XAUI electrical interface 4x 3.125 Gb/s Ethernet (FTLX1442E2) 4x 3.1875 Gb/s Fibre Channel (FTLX1442F2) Management and control via MDIO 2-wire bus 70-pin connector Separated signal/chassis ground Mid Pak module variance for front panel mounting De-latch mechanism with low extraction force APPLICATIONS 10GBASE-LR 10G Ethernet (FTLX1442E2) 1200-SM-LL-L 10G Fibre Channel (FTLX1442F2) PRODUCT SELECTION Part Number Application FTLX1442E2 10G Ethernet FTLX1442F2 10G Fibre Channel (c) Finisar Corporation - July 2009 Rev. B Page 1 FTLX1442 Product Specification - July 2009 I. PIN DESCRIPTION Signal Name Level I/O Management and Monitoring Ports MDIO Open Drain I/O Pin No. Description 17 MDC I 18 Management Data I/O. Requires external 10 - 22 k pull-up to the APS on host. Management Data Clock Input 1 19 Port Address Input bit 4 I 20 Port Address Input bit 3 I 21 Port Address Input bit 2 I 22 Port Address Input bit 1 I 23 Port Address Input bit 0 LASI 1.2 V CMOS 1.2 V CMOS 1.2 V CMOS 1.2 V CMOS 1.2 V CMOS 1.2 V CMOS Open Drain O 9 RESET Open Drain I 10 Link Alarm Status Interrupt Output. Open Drain Compatible Output with 10 - 20 k pull-up on host. Logic high = Normal Operation Logic low = Status Flag Triggered Reset Input. Open Drain Compatible Input with 22 k pull-up to APS internal to transponder. Logic high = Normal Operation Logic low = RESET Vendor Specific Pins. Leave unconnected when not used. TX ON/OFF Input. Open Drain Compatible Input with 22 k pull-up to APS internal to transponder. Logic high = Transmitter On Logic low = Transmitter Off Pulled low inside transponder through a 1 k resistor to Ground PRTAD4 PRTAD3 PRTAD2 PRTAD1 PRTAD0 Vendor Specific TX ON/OFF 11,15,16,24 Open Drain MOD DETECT Transmit Functions Reserved Reserved TX LANE 3- AC-coupled, TX LANE 3+ Internally biased differential TX LANE 2- XAUI TX LANE 2+ TX LANE 1- TX LANE 1+ TX LANE 0- TX LANE 0+ (c) Finisar Corporation - July 2009 I 12 O 14 I I I I 68 67 65 64 Reserved For Future Use Reserved For Future Use Module XAUI Input Lane 3- Module XAUI Input Lane 3+ I I I I I I 62 61 59 58 56 55 Module XAUI Input Lane 2- Module XAUI Input Lane 2+ Module XAUI Input Lane 1- Module XAUI Input Lane 1+ Module XAUI Input Lane 0- Module XAUI Input Lane 0+ Rev. B Page 2 FTLX1442 Product Specification - July 2009 Receive Functions Reserved Reserved RX LANE 0+ AC-coupled, RX LANE 0- Internally biased differential RX LANE 1+ XAUI RX LANE 1- RX LANE 2+ RX LANE 2- RX LANE 3+ RX LANE 3- DC Power GND 0 V DC APS APS SENSE +1.2 V +1.2 V APS SET O O O O 38 39 41 42 Reserved For Future Use Reserved For Future Use Module XAUI Output Lane 0+ Module XAUI Output Lane 0- O O O O O O 44 45 47 48 50 51 Module XAUI Output Lane 1+ Module XAUI Output Lane 1- Module XAUI Output Lane 2+ Module XAUI Output Lane 2- Module XAUI Output Lane 3+ Module XAUI Output Lane 3- 1, 2, 3, 33, 34, 35, 36, 37, 40, 43, 46, 49, 52, 53, 54, 57, 60, 63, 66, 69, 70 7, 8, 28, 29 27 Ground connection for signal ground on the module 25 3.3 V +3.3 V DC 5, 6, 30, 31 5.0 V +5.0 V DC 4, 32 Reserved Reserved 26 13 (c) Finisar Corporation - July 2009 Rev. B Input from Adaptive Power Supply APS Sense Output. Connected to the APS input inside transponder. Feedback input from APS. Connected to GND through a 1180 resistor inside the transponder. DC Power Input, +3.3 V DC, Nominal DC Power Input, +5.0 V DC, Nominal Reserved for APD. Reserved. Page 3 FTLX1442 Product Specification - July 2009 Electrical Pad Layout Fig 1-X2 Transponder Electrical Pad Layout II. Absolute Maximum Ratings Parameter Storage Ambient Temperature1) Operating Case Temperature1) Supply Voltage +5.0 V Supply Voltage +3.3 V Supply Voltage APS Static Discharge Voltage, All Pins2) Average Receive Optical Power Notes: 1) 2) Symbol TS TC V5 V3 Vaps STd RxP max Limit Values min. max. -40 85 0 70 0 6 0 4 0 1.5 500 1.5 Unit C C V V V V dBm Non-condensing. HBM Exceeding any one of these values may permanently destroy the device. (c) Finisar Corporation - July 2009 Rev. B Page 4 FTLX1442 Product Specification - July 2009 III. Electrical Characteristics Recommended Operating Conditions Parameter Operating Case Temperature1) Transponder Total Power Consumption Supply Voltage +5.0 V Supply Current +5.0 V Supply Voltage +3.3 V Supply Current +3.3 V Supply Voltage APS Supply Current APS Values typ. Symbol TC P min. 0 VCC5 ICC5 VCC3 ICC3 VCC aps ICC aps 4.75 5.0 3.14 3.3 1.152 1.2 2.2 max. 70 3.5 Unit C W 5.25 10 3.47 550 1.248 1000 V mA V mA V mA 1) Worst case thermal location, see Figure 11. See also Environmental Performance. Electrical DC Characteristics (VCC5 = 4.75 V to 5.25 V, VCC3 = 3.14 V to 3.47 V, VCC aps = 1.152 V to 1.248 V, TC = 0C to 70C) Parameter Symbol min. 1.2 V CMOS (1.8 V CMOS Compatible1)) I/O DC Characteristics (PRTAD; LASI; RESET; TX_ONOFF) External Pull-up Resistor for Open Drain Rpullup 10 Output High Voltage2) Voh 1 Output Low Voltage2) Vol Input High Voltage Vih 0.84 Input Low Voltage Vil Input Pull-down Current3) Ipd 20 XAUI I/O DC Characteristics (TXLANE[0..3]; RXLANE[0..3]) Values typ. max. Unit 22 0.15 1.5 0.36 120 k V V V V A Differential Input Amplitude (pk-pk) 4) Vin_xaui Differential Output Amplitude (pk-pk) 4) Vout_xaui MDIO I/O DC Characteristics (MDIO; MDC) 200 800 2500 1600 mV mV Output Low Voltage5) Output Low Current Input High Voltage Input Low Voltage Pull-up Supply Voltage Input Capacitance Load Capacitance External Pull-up Resistance -0.3 0.2 4 1.5 0.36 1.248 10 470 V mA V V V pF pF 1) 2) 3) 4) 5) VOL IOL VIH VIL VPU CIN CLOAD RLOAD 0.84 -0.3 1.152 200 1.2 For 1.8 V CMOS Voh = 1.65 V min., Vol = 0.15 V max., Vih = 1.17 V min., Vil = 0.63 V max. Rpull-up = 10 k to 1.8 V. Vin = 1.2 V. AC coupled. IOL = 100 A. (c) Finisar Corporation - July 2009 Rev. B Page 5 FTLX1442 Product Specification - July 2009 Electrical AC Characteristics (VCC5 = 4.75 V to 5.25 V, VCC3 = 3.14 V to 3.47 V, VCC aps = 1.152 V to 1.248 V, TC = 0C to 70C) Values Parameter Symbol Unit min. typ. max. XAUI Input AC Characteristics (TXLANE[0..3]) Baud Rate RXAUIIN Gbit/s Fibre Channel 3.1875 Ethernet 3.125 Baud Rate Tolerance RTOLXAUI -100 100 ppm Differential Input Impedance ZINXAUI 80 100 120 Differential Return Loss1) |SDD11| 10 dB Common Mode Return Loss1) |SCC11| 6 dB Input Differential Skew2) tSKEWIN 75 ps Jitter Amplitude Tolerance3) JXAUITOL 0.65 UIp-p XAUI Output AC Characteristics (RXLANE[0..3]) Baud Rate RXAUIOUT Gbit/s Fibre Channel 3.1875 Ethernet 3.125 Baud Rate Variation RXAUIVAR -100 100 ppm XAUI Eye Mask (far-end) According to IEEE 802.3ae and Fibre Channel 1200-SM-LL-L Output Differential Skew tSKEWOUT 15 ps Output Differential Impedance ZOUTXAUI 80 100 120 Differential Output Return Loss4) |S22| 10 dB Total Jitter5) TJXAUI 0.35 UI Deterministic Jitter5) DJXAUI 0.37 UI Power-On Reset AC Characteristics Power-On Reset and TX_ONOFF According to XENPAK MSA Issue 3.0, 2002-9-18 Characteristics MDIO I/O AC Characteristics (MDIO; MDC) MDIO Data Hold Time tHOLD 10 ns MDIO Data Setup Time tSU 10 ns Delay from MDC Rising Edge to tDELAY 300 ns MDIO Data Change MDC Clock Rate MAX 2.5 MHz 1) 2) 3) 4) 5) 100 MHz to 2.5 GHz, with 100 reference for Differential, 25 reference for Common Mode. At crossing point. Per IEEE Std 802.3ae. 312.5 MHz to 625 MHz. See IEEE 802.3ae for 625MHz to 3.125 GHz. At near-end, No pre-equalization, 1 UI = 320 ps. (c) Finisar Corporation - July 2009 Rev. B Page 6 FTLX1442 Product Specification - July 2009 IV. Optical Characteristics (VCC5 = 4.75 V to 5.25 V, VCC3 = 3.14 V to 3.47 V, VCC aps = 1.152 V to 1.248 V, TC = 0C to 70C, BER 1E-12, Bit Rate 10.3125) Values Parameter Symbol Unit min. typ. max. Transmitter Launch Power in OMA PO-OMA -5.2 dBm Average Launch Power PO-Avg -8.2 0.5 dBm Center Wavelength Range C-Tx 1290 1330 nm Spectral Width (-20 dB) 0.6 nm I Side Mode Suppression Ratio SMSR 30 dB Extinction Ratio ER 3.5 dB Relative Intensity Noise12OMA RIN -128 dB/Hz Launch Power minus TDP PO-TDP -6.2 dBm Transmitter and Dispersion Penalty TDP 3.2 dB Average Launch Power of OFF PO-OFF -30 dBm Transmitter Optical Return Loss Tolerance ORLT 12 dB Transmitter Reflectance REFTX -12 dB Eye Mask Definition According to IEEE 802.3ae and Fibre Channel 1200-SM-LL-L Receiver Stressed Receiver Sensitivity PIN-S -10.3 dBm Rx Sensitivity in OMA1) PIN-O -12.6 dBm Average Receiver Power1) PIN -14.4 0.5 dBm Receiver Damage Power PIN-dmg 1.5 dBm Loss Of Signal Assert Level PLOSa -13 dBm Loss Of Signal Hysteresis PLOSh 1 dB Receiver Reflectance REFRX -12 dB Receive Electrical 3dB Upper Cutoff FC 12.3 GHz Frequency Center Wavelength Range C-RX 1260 1355 nm Stressed Signal Calibration Vertical Eye Closure Penalty 2.2 dB Stressed Eye Jitter 0.3 UIpp 1) Average Receiver Power (min), which is defined for an ideal input signal, is informative only. V. General Specifications Optical Interface Standard Specifications Standard B1.1 SMF B1.3 SMF Differential Group Delay Maximum (ps) 10 10 Operating Range 1) (meters) 2 to 10,000 2 to 10,000 Notes: 1) Operating range as defined by IEEE and Fibre Channel standards. Longer reach possible depending upon link implementation. (c) Finisar Corporation - July 2009 Rev. B Page 7 FTLX1442 Product Specification - July 2009 Environmental Performance Operating case temperature: Operating humidity: 0C to +70C 0% -95% RH non-condensing Fibers and Connectors The transponder has SC receptacles for both Tx and Rx. The transponder is designed for single mode SC cables, 0 polished endface (PC). 70-pin Connector The module interface connector is a 70-pin, printed circuit board edge connection with a 0.5 mm pitch. The appropriate mating connector for the customer PCB is a 70-pin SMT, dual row, right angled, edge connector, 0.5 mm pitch (Tyco Electronics part number 1367337-1, Molex part number 74441-0003 or equivalent). Rail Requirement The X2 rail system required to mount the X2 module is fully defined by the MSA. (Tyco Electronics part number 1367608-1: designed for belly to belly applications; and 1367610-1: designed for single sided board mount to fit into the standard host PCB footprint, or equivalent). For further details, please refer to vendor-supplied information. Aqueous Wash Finisar X2 transponders are neither solderable nor aqueous washable and are not intended for these processes. VI. Regulatory Compliance Feature ESD: Electrostatic Discharge to the Electrical Pins (HBM) Immunity: Against Electrostatic Discharge (ESD) to the Module Receptacle Standard EIA/JESD22-A114-B (MIL-STD 883D Method 3015.7) EN 61000-4-2 IEC 61000-4-2 Immunity: Against Radio Frequency Electromagnetic Field EN 61000-4-3 IEC 61000-4-3 Emission: Electromagnetic Interference (EMI) FCC 47 CFR Part 15, Class B EN 55022 Class B CISPR 22 (c) Finisar Corporation - July 2009 Rev. B Comments Class 1a (> 500 V) Discharges ranging from 2 kV to 25 kV to the front end / faceplate / receptacle cause no damage to module (under recommended conditions). With a field strength of 10 V/m, noise frequency ranges from 10 MHz to 2 GHz. No effect on module performance between the specification limits. Noise frequency range: 30 MHz to 40 GHz Radiated emission does not exceed specified limits when measured inside a shielding enclosure with MSA conform cutout. Page 8 FTLX1442 Product Specification - July 2009 Eye Safety Finisar FTLX1442 transponders are Class 1 Laser Products. They are certified per the following standards: Feature Agency Standard Laser Eye Safety Laser Eye Safety FDA/CDRH CDRH 21 CFR 1040 and Laser Notice 50 TUV R72082131 Electrical Safety Electrical Safety TUV EN 60825-1: 1994+A11:1996+A2:2001 IEC 60825-1: 1993+A1:1997+A2:2001 IEC 60825-2: 2000, Edition 2 EN 60950 CLASS 3862.07 CLASS 3862.87 1439230 UL/CSA Certificate Number 9210176 R72082131 Copies of the referenced certificates will be available at Finisar Corporation upon request. VII. DOM Parameters Parameter Transponder Temperature Monitor Accuracy1) Laser Bias Current Monitor Accuracy2) Transmit Power Monitor Accuracy3) Receive Power Monitor Accuracy3) 1) 2) 3) min. -5 -10 -3 -3 Values typ. max. +5 +10 +3 +3 Unit C % dB dB 0 to 70C case temperature. 0 to 12.5 mA. -8.2 dBm to +0.5 dBm. VIII. Mechanical Characteristics Parameter Symbol min. Module Retention Force (latch strength) Module Insertion Force Module Extraction Force (with kick-out) Module Extraction Force (without kick-out) FRET FIN FEXT-K FEXT Values typ. 200 40 16 25 Unit max. N N N N Pull Sleeve front face color is blue. (c) Finisar Corporation - July 2009 Rev. B Page 9 FTLX1442 Product Specification - July 2009 Package Outline Figure 2-X2 Mechanical Dimensions IX. References The following references are provided for informational purposes only. The parameters and operational behavior outlined in this specification describe the complete functionality of the 10G Transponder. Contact Finisar for any items concerning the operational characteristics of this device. X. IEEE Std 802.3ae-2002 clause 52, 10GBASE-LR Fibre Channel 10GFC Draft 4.0, 1200-SM-LL-L X2 MSA Issue 2.0b For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 sales@finisar.com www.finisar.com (c) Finisar Corporation - July 2009 Rev. B Page 10