142
Dimensions in millimeters (inch) unless otherwise stated
Other options available. For complete details
on variety, part numbers, installation and
specification, go to
Other options available. For complete details
on variety, part numbers, installation and
specification, go to
ACTUAL SIZE
ACTUAL SIZE
SMALL
MEDIUM
LARGE
24 Cam Latch
Flush T-handle · Adjustable grip
• Concealed mounting type
Material and Finish
Zinc alloy and steel, zinc plated or
stainless steel
Performance Details
Maximum static load:
445 N (100 lbf)
Installation Notes
Maximum tightening torque of
mounting nuts not to exceed
2.8 Nm (25 inlbf)
Keys
See page 130
114.3
(4.50)
57.2
(2.25)
65.1
(2.56)
900
approx.
Cam
Cup
Lock assembly
option
88.9
(3.50)
30.2
(1.19)
82.6
(3.25)
20.6
(.81)
30.2
(1.19)
38.9
(1.53)
65.1
(2.56)
17.5 (.69)
34.9 (1.38)
27.8 (1.09) Minimum
39.7 (1.56) Maximum
Handle
Hex nut
Lock arm
2 Holes, Ø 6.5 (.26) in
actuator for attaching rods
Door 7.9 (0.31) Maximum
Grip range
Part Number
Style
With Mounting Studs
Cup and bracket polished stainless steel.
Handle zinc chrome plated
Cup and bracket steel dacrotized.
Handle zinc dacrotized
Locking keyed alike CH751 supplied 24-20-812-35 24-20-812-10
Non-locking 24-20-302-35 24-20-302-10
Non-locking environmentally sealed 24-20-312-35 24-20-312-10
www.southco.com/69
69 Cam Latch
Arrowhead · Detent design · Adjustable grip
• Arrow indicates cam
orientation
• Single hole installation
• Detented design
• Adjustable grip
Material and Finish
Nylon and steel, zinc plated
Performance Details
Small size working load:
44 N (10 lbf)
Medium size working load:
220 N (50 lbf)
Large size working load:
330 N (75 lbf)
Knob
BE
Mounting nut
Lock nuts
Ferrule Sleeve
Pin
Cam
forward
Cam
reversed
Shaft
C
D
A
Grip range
Lock
washers
G
www.southco.com/24
Size Part Number G Grip Range A B C D E
Minimum Maximum
Small 69-10-301-11 4 (.16) 28.2 (1.11) 12.7 (.50) 12.7 (.50) Max. 38.1 (1.50) 13.5 (.53) 4.75 (.188)
Medium 69-10-401-11 3.2 (.13) 33.3 (.13) 19.1 (.75) 17.5 (.69) Max. 47.5 (1.87)) 15.9 (.63) 6.35 (.25)
Large 69-10-501-11 4.8 (.19) 61.9 (2.44) 28.6 (1.13) 25.4 (1) Max. 79.2 (3.12) 34.1 (1.34) 12.7 (.50)
102 •
Products identified with this symbol are stocked subject to prior sale in one or more of our global locations. If unavailable from our facility nearest you, allow for shipping time from another facility.
Pawl/Cam Action Latches
millimeter (inch)
millimeter
(inch)
Dimensions without tolerances are for reference only.
KNOB
KNOB
HEIGHT
MAX. OUTER
PANEL THICKNESS
MOUNTING
NUT
JAM
NUT
FERRULE
SLEEVE
PIN
PAWL
PAWL
REVERSED
SHAFT
L
P
D
GRIP RANGE
LOCK-
WASHERS
Southco® Pawl/Cam Action Latches
Arrowhead (Pawl Indicator) Design
• Detents in full open and closed positions
• Turn clockwise or counter-clockwise to operate
Material and Finish
KNOB: Nylon, black. SHAFT: Low carbon
steel, zinc plate, chromate plus sealer.
PAWL: 1010 Steel, zinc plate, chromate plus
sealer. FERRULE: 6061 Aluminum, natural.
SLEEVE: Die-cast zinc with chemical
protective film. MOUNTING NUT: (300
SERIES) 303 Stainless steel, passivated.
MOUNTING NUT: (Other series) Steel,
zinc plated plus chromate dip. JAM NUTS:
Steel, zinc plate, chromate plus sealer.
SPRING: 302 Stainless steel, natural. PIN:
303 Stainless steel, natural. WASHER:
Stainless steel, passivated. LOCKWASHERS:
(300 Series) Stainless steel, passivated.
LOCKWASHERS: (Other Series) Spring steel,
zinc immersion coating.
PANEL
PAWL
LATCH
X
W
H
TO
Type
“A”
Turn clockwise
to latch.
Type
“B”
Turn counter-
clockwise
to latch.
FRAME
X
H
TO
LATCH
PAWL
FRAME
W
Panel Preparation Installation
Latch operates through 90° rotation in direction
shown with a positive click stop at both extremes.
Pawl pulls up at both extremes.
1. Adjust ferrule to desired knob height (see table).
2. Remove shaft nuts, lockwashers, pawl and mount-
ing nut (if assembled).
3. Insert shaft through hole in panel to engage flats
of sleeve with shaped hole.
4. Check arrow orientation.
5. Apply and tighten mounting nut.
6. Install pawl and shaft nuts as shown, position pawl
for desired grip and use two wrenches to tighten
nuts firmly against pawl.
DIMENSIONS
L PØD
12.7
(0.50)
19.1
(0.75)
28.6
(1.13)
38.1
(1.50)
47.5
(1.87)
79.2
(3.12)
13.5
(0.53)
15.9
(.63)
34.1
(1.34)
KNOB
HEIGHT
12.7 (.50) MAX.
9.5( .38) MIN.
17.5 (.69) MAX.
12.7 (.50) MIN.
25.4 (1.00) MAX.
19.1 (.75) MIN.
1.59 (.063)
4.75 (.188)
1.59 (.063)
6.35 (.250)
6.35 (.250)
12.70 (.500)
4 (.16)
7.1 (.28)
3.2 (.13)
7.9 (.31)
4.8 (.19)
11.1 (.44)
15 (.59)
18.3 (.72)
15.9 (.63)
20.6 (.81)
30.2 (1.19)
36.5 (1.44)
13.4 (.53)
18.3 (.72)
15.9 (.63)
20.6 (.81)
30.2 (1.19)
36.5 (1.44)
24.6 (.97)
28.2 (1.11)
28.6 (1.13)
33.3 (1.31)
55.6 (2.19)
61.9 (2.44)
69-10-301-11 •
69-10-401-11 •
69-10-501-11 •
300
400
500
8.33
(.328)
11.51
(.453)
16.26
(.640)
6.99
(.275)
9.78
(.385)
13.72
(.540)
9.53
(.375)
12.30
(.484)
22.23
(.875)
11.11
(.438)
13.10
(.516)
25.40
(1.000)
6-32
UNC
10-32
UNF
5/16-24
UNF
shaft
thread
size
X
H
W
INSTALLATION
Series
±0.13
(±0.05)
+0.13
-0.00
(+.005
-0.00) MIN. MAX.
GRIP RANGE
Pawl as shown Pawl reversed
MIN. MAX. MIN. MAX.
Max.
Outer
Panel
Thickness
PART
NUMBERS
Height of knob (from outside surface of
panel) is adjustable within limits shown by
adjusting ferrule on threaded sleeve before in-
stalling latch. MAX. OUTER PANEL THICKNESS
and GRIP RANGE are governed by specific
knob height selected – (see table).
