Features * Fast Read Access Time - 120 ns * Automatic Page Write Operation * * * * * * * * * * - Internal Address and Data Latches for 128 Bytes - Internal Control Timer Fast Write Cycle Time - Page Write Cycle Time - 10 ms Maximum - 1 to 128-byte Page Write Operation Low Power Dissipation - 40 mA Active Current - 200 A CMOS Standby Current Hardware and Software Data Protection DATA Polling for End of Write Detection High Reliability CMOS Technology - Endurance: 104 or 105 Cycles - Data Retention: 10 Years Single 5V 10% Supply CMOS and TTL Compatible Inputs and Outputs JEDEC Approved Byte-wide Pinout Industrial Temperature Ranges Green (Pb/Halide-free) Packaging Option Only 1-megabit (128K x 8) Paged Parallel EEPROM AT28C010 1. Description The AT28C010 is a high-performance electrically-erasable and programmable readonly memory. Its 1 megabit of memory is organized as 131,072 words by 8 bits. Manufactured with Atmel's advanced nonvolatile CMOS technology, the device offers access times to 120 ns with power dissipation of just 220 mW. When the device is deselected, the CMOS standby current is less than 200 A. The AT28C010 is accessed like a Static RAM for the read or write cycle without the need for external components. The device contains a 128-byte page register to allow writing of up to 128 bytes simultaneously. During a write cycle, the address and 1 to 128 bytes of data are internally latched, freeing the address and data bus for other operations. Following the initiation of a write cycle, the device will automatically write the latched data using an internal control timer. The end of a write cycle can be detected by DATA polling of I/O7. Once the end of a write cycle has been detected a new access for a read or write can begin. Atmel's AT28C010 has additional features to ensure high quality and manufacturability. The device utilizes internal error correction for extended endurance and improved data retention characteristics. An optional software data protection mechanism is available to guard against inadvertent writes. The device also includes an extra 128 bytes of EEPROM for device identification or tracking. 0353I-PEEPR-08/09 AT28C010 2. Pin Configurations CE Chip Enable OE Output Enable WE Write Enable I/O0 - I/O7 Data Inputs/Outputs NC No Connect DC Don't Connect A12 A15 A16 DC VCC WE NC Addresses A7 A6 A5 A4 A3 A2 A1 A0 I/O0 4 3 2 1 32 31 30 A0 - A16 5 6 7 8 9 10 11 12 13 29 28 27 26 25 24 23 22 21 14 15 16 17 18 19 20 Function 32-lead PLCC Top View A14 A13 A8 A9 A11 OE A10 CE I/O7 I/O1 I/O2 GND I/O3 I/O4 I/O5 I/O6 Pin Name 2.2 Note: 2.1 PLCC package pin 1 is Don't Connect. 32-lead TSOP Top View A11 A9 A8 A13 A14 NC WE VCC NC A16 A15 A12 A7 A6 A5 A4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 OE A10 CE I/O7 I/O6 I/O5 I/O4 I/O3 GND I/O2 I/O1 I/O0 A0 A1 A2 A3 2 0353I-PEEPR-08/09 AT28C010 3. Block Diagram 4. Device Operation 4.1 Read The AT28C010 is accessed like a Static RAM. When CE and OE are low and WE is high, the data stored at the memory location determined by the address pins is asserted on the outputs. The outputs are put in the high impedance state when either CE or OE is high. This dual-line control gives designers flexibility in preventing bus contention in their system. 4.2 Byte Write A low pulse on the WE or CE input with CE or WE low (respectively) and OE high initiates a write cycle. The address is latched on the falling edge of CE or WE, whichever occurs last. The data is latched by the first rising edge of CE or WE. Once a byte write has been started it will automatically time itself to completion. Once a programming operation has been initiated and for the duration of tWC, a read operation will effectively be a polling operation. 4.3 Page Write The page write operation of the AT28C010 allows 1 to 128 bytes of data to be written into the device during a single internal programming period. A page write operation is initiated in the same manner as a byte write; the first byte written can then be followed by 1 to 127 additional bytes. Each successive byte must be written within 150 s (tBLC) of the previous byte. If the tBLC limit is exceeded the AT28C010 will cease accepting data and commence the internal programming operation. All bytes during a page write operation must reside on the same page as defined by the state of the A7 - A16 inputs. For each WE high to low transition during the page write operation, A7 - A16 must be the same. The A0 to A6 inputs are used to specify which bytes within the page are to be written. The bytes may be loaded in any order and may be altered within the same load period. Only bytes which are specified for writing will be written; unnecessary cycling of other bytes within the page does not occur. 4.4 DATA Polling The AT28C010 features DATA Polling to indicate the end of a write cycle. During a byte or page write cycle an attempted read of the last byte written will result in the complement of the written data to be presented on I/O7. Once the write cycle has been completed, true data is valid on all outputs, and the next write cycle may begin. DATA Polling may begin at anytime during the write cycle. 3 0353I-PEEPR-08/09 4.5 Toggle Bit In addition to DATA Polling the AT28C010 provides another method for determining the end of a write cycle. During the write operation, successive attempts to read data from the device will result in I/O6 toggling between one and zero. Once the write has completed, I/O6 will stop toggling and valid data will be read. Reading the toggle bit may begin at any time during the write cycle. 4.6 Data Protection If precautions are not taken, inadvertent writes may occur during transitions of the host system power supply. Atmel(R) has incorporated both hardware and software features that will protect the memory against inadvertent writes. 4.6.1 Hardware Protection Hardware features protect against inadvertent writes to the AT28C010 in the following ways: (a) VCC sense - if VCC is below 3.8V (typical) the write function is inhibited; (b) VCC power-on delay - once VCC has reached 3.8V the device will automatically time out 5 ms (typical) before allowing a write; (c) write inhibit - holding any one of OE low, CE high or WE high inhibits write cycles; and (d) noise filter--pulses of less than 15 ns (typical) on the WE or CE inputs will not initiate a write cycle. 4.6.2 Software Data Protection A software controlled data protection feature has been implemented on the AT28C010. When enabled, the software data protection (SDP), will prevent inadvertent writes. The SDP feature may be enabled or disabled by the user; the AT28C010 is shipped from Atmel with SDP disabled. SDP is enabled by the host system issuing a series of three write commands; three specific bytes of data are written to three specific addresses (refer to Software Data Protection Algorithm). After writing the 3-byte command sequence and after tWC the entire AT28C010 will be protected against inadvertent write operations. It should be noted, that once protected the host may still perform a byte or page write to the AT28C010. This is done by preceding the data to be written by the same 3-byte command sequence used to enable SDP. Once set, SDP will remain active unless the disable command sequence is issued. Power transitions do not disable SDP and SDP will protect the AT28C010 during power-up and power-down conditions. All command sequences must conform to the page write timing specifications. The data in the enable and disable command sequences is not written to the device and the memory addresses used in the sequence may be written with data in either a byte or page write operation. After setting SDP, any attempt to write to the device without the 3-byte command sequence will start the internal write timers. No data will be written to the device; however, for the duration of tWC, read operations will effectively be polling operations. 4.7 Device Identification An extra 128 bytes of EEPROM memory are available to the user for device identification. By raising A9 to 12V 0.5V and using address locations 1FF80H to 1FFFFH the bytes may be written to or read from in the same manner as the regular memory array. 4.8 Optional Chip Erase Mode The entire device can be erased using a 6-byte software code. Please see Software Chip Erase application note for details. 4 AT28C010 0353I-PEEPR-08/09 AT28C010 5. DC and AC Operating Range Operating Temperature (Case) Ind. AT28C010-12 AT28C010-15 -40C - 85C -40C - 85C 5V 10% 5V 10% VCC Power Supply 6. Operating Modes Mode CE OE WE I/O Read VIL VIL VIH DOUT VIL VIH VIL DIN VIH X(1) X High Z Write Inhibit X X VIH Write Inhibit X VIL X Output Disable X VIH X Write (2) Standby/Write Inhibit Notes: High Z 1. X can be VIL or VIH. 2. Refer to AC Programming Waveforms. 7. Absolute Maximum Ratings* Temperature Under Bias................................ -55C to +125C *NOTICE: Storage Temperature ..................................... -65C to +150C All Input Voltages (including NC Pins) with Respect to Ground ...................................-0.6V to +6.25V All Output Voltages with Respect to Ground .............................-0.6V to VCC + 0.6V Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability Voltage on OE and A9 with Respect to Ground ...................................-0.6V to +13.5V 8. DC Characteristics Symbol Parameter Condition ILI Input Load Current ILO Min Max Units VIN = 0V to VCC + 1V 10 A Output Leakage Current VI/O = 0V to VCC 10 A ISB1 VCC Standby Current CMOS CE = VCC - 0.3V to VCC + 1V 200 A ISB2 VCC Standby Current TTL CE = 2.0V to VCC + 1V 3 mA ICC VCC Active Current f = 5 MHz; IOUT = 0 mA 40 mA VIL Input Low Voltage 0.8 V VIH Input High Voltage VOL Output Low Voltage IOL = 2.1 mA VOH1 Output High Voltage IOH = -400 A 2.4 V VOH2 Output High Voltage CMOS IOH = -100 A; VCC = 4.5V 4.2 V 2.0 V 0.45 V 5 0353I-PEEPR-08/09 9. AC Read Characteristics AT28C010-12 Min Max AT28C010-15 Symbol Parameter Min Max Units tACC Address to Output Delay 120 150 ns tCE(1) CE to Output Delay tOE(2) 120 150 ns OE to Output Delay 0 50 tDF(3)(4) 0 55 ns CE or OE to Output Float 0 50 0 55 ns tOH Output Hold from OE, CE or Address, Whichever Occurred First 0 0 ns tCEPH(5) CE Pulse High Time 50 50 ns 10. AC Read Waveforms(1)(2)(3)(4) tCEPH Notes: 1. CE may be delayed up to tACC - tCE after the address transition without impact on tACC. 2. OE may be delayed up to tCE - tOE after the falling edge of CE without impact on tCE or by tACC - tOE after an address change without impact on tACC. 3. tDF is specified from OE or CE whichever occurs first (CL = 5 pF). 4. This parameter is characterized and is not 100% tested. 5. If CE is de-asserted, it must remain de-asserted for at least 50ns during read operations otherwise incorrect data may be read. 6 AT28C010 0353I-PEEPR-08/09 AT28C010 11. Input Test Waveforms and Measurement Level tR, tF < 5 ns 12. Output Test Load 13. Pin Capacitance f = 1 MHz, T = 25C(1) Symbol Typ Max Units Conditions CIN 4 10 pF VIN = 0V COUT 8 12 pF VOUT = 0V Note: 1. This parameter is characterized and is not 100% tested. 7 0353I-PEEPR-08/09 14. AC Write Characteristics Symbol Parameter Min Max Units tAS, tOES Address, OE Set-up Time 0 ns tAH Address Hold Time 50 ns tCS Chip Select Set-up Time 0 ns tCH Chip Select Hold Time 0 ns tWP Write Pulse Width (WE or CE) 100 ns tDS Data Set-up Time 50 ns tDH, tOEH Data, OE Hold Time 0 ns 15. AC Write Waveforms 15.1 WE Controlled 15.2 CE Controlled 8 AT28C010 0353I-PEEPR-08/09 AT28C010 16. Page Mode Characteristics Symbol Parameter Min Max Units tWC Write Cycle Time 10 ms tAS Address Set-up Time 0 ns tAH Address Hold Time 50 ns tDS Data Set-up Time 50 ns tDH Data Hold Time 0 ns tWP Write Pulse Width 100 ns tBLC Byte Load Cycle Time tWPH Write Pulse Width High 150 50 s ns 17. Page Mode Write Waveforms(1)(2) Notes: 1. A7 through A16 must specify the same page address during each high to low transition of WE (or CE). 2. OE must be high only when WE and CE are both low. 18. Chip Erase Waveforms tS = 5 sec (min.) tW = tH = 10 msec (min.) VH = 12.0V 0.5V 9 0353I-PEEPR-08/09 19. Software Data Protection Enable Algorithm(1) Notes: 20. Software Data Protection Disable Algorithm(1) LOAD DATA AA TO ADDRESS 5555 LOAD DATA AA TO ADDRESS 5555 LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA A0 TO ADDRESS 5555 LOAD DATA 80 TO ADDRESS 5555 WRITES ENABLED(2) LOAD DATA XX TO ANY ADDRESS(4) LOAD DATA AA TO ADDRESS 5555 LOAD LAST BYTE TO LAST ADDRESS LOAD DATA 55 TO ADDRESS 2AAA ENTER DATA PROTECT STATE 1. Data Format: I/O7 - I/O0 (Hex); Address Format: A14 - A0 (Hex). 2. Write Protect state will be activated at end of write even if no other data is loaded. 3. Write Protect state will be deactivated at end of write period even if no other data is loaded. LOAD DATA 20 TO ADDRESS 5555 EXIT DATA PROTECT STATE(3) LOAD DATA XX TO ANY ADDRESS(4) 4. 1 to 128 bytes of data are loaded. LOAD LAST BYTE TO LAST ADDRESS 21. Software Protected Write Cycle Waveforms(1)(2)(3) Notes: 1. A0 through A14 must conform to the addressing sequence for the first 3 bytes as shown above. 2. After the command sequence has been issued and a page write operation follows, the page address inputs (A7 - A16) must be the same for each high to low transition of WE (or CE). 3. OE must be high only when WE and CE are both low. 10 AT28C010 0353I-PEEPR-08/09 AT28C010 22. Data Polling Characteristics(1) Symbol Parameter tDH Data Hold Time 10 ns tOEH OE Hold Time 10 ns tOE OE to Output Delay(2) tWR Write Recovery Time Notes: Min Typ Max Units ns 0 ns 1. These parameters are characterized and not 100% tested. 2. See AC Read Characteristics. 23. Data Polling Waveforms 24. Toggle Bit Characteristics(1) Symbol Parameter Min tDH Data Hold Time 10 ns tOEH OE Hold Time 10 ns tOE OE to Output Delay(2) tOEHP OE High Pulse tWR Notes: Write Recovery Time Typ Max Units ns 150 ns 0 ns 1. These parameters are characterized and not 100% tested. 2. See AC Read Characteristics. 25. Toggle Bit Waveforms Notes: 1. Toggling either OE or CE or both OE and CE will operate toggle bit. 2. Beginning and ending state of I/O6 will vary. 3. Any address location may be used but the address should not vary. 11 0353I-PEEPR-08/09 26. Ordering Information 26.1 26.1.1 tACC (ns) 120 150 26.1.2 Green Package Option (Pb/Halide-free) AT28C010 ICC (mA) Active Standby 40 0.2 40 0.2 Package 32J AT28C010-12TU 32T AT28C010-15JU 32J AT28C010-15TU 32T Ordering Code Package AT28C010E-12JU 32J AT28C010E-12TU 32T AT28C010E-15JU 32J AT28C010E-15TU 32T Operation Range Industrial (-40 to 85 C) AT28C010E ICC (mA) tACC (ns) Active Standby 120 40 0.2 150 Ordering Code AT28C010-12JU 40 0.2 Operation Range Industrial (-40 to 85 C) Package Type 32J 32-lead, Plastic J-leaded Chip Carrier (PLCC) 32T 32-lead, Plastic Thin Small Outline Package (TSOP) Options Blank Standard Device: Endurance = 10K Write Cycles; Write Time = 10 ms E High-endurance Option: Endurance = 100K Write Cycles 26.2 Die Products Reference Section: Contact Atmel Sales for Parallel EEPROM Die Product availability. 12 AT28C010 0353I-PEEPR-08/09 AT28C010 27. Packaging Information 27.1 32J - PLCC 1.14(0.045) X 45 PIN NO. 1 IDENTIFIER 1.14(0.045) X 45 0.318(0.0125) 0.191(0.0075) E1 E E2 B1 B e A2 D1 A1 D A 0.51(0.020)MAX 45 MAX (3X) COMMON DIMENSIONS (Unit of Measure = mm) D2 Notes: 1. This package conforms to JEDEC reference MS-016, Variation AE. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is .010"(0.254 mm) per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. 3. Lead coplanarity is 0.004" (0.102 mm) maximum. SYMBOL MIN NOM MAX A 3.175 - 3.556 A1 1.524 - 2.413 A2 0.381 - - D 12.319 - 12.573 D1 11.354 - 11.506 D2 9.906 - 10.922 E 14.859 - 15.113 E1 13.894 - 14.046 E2 12.471 - 13.487 B 0.660 - 0.813 B1 0.330 - 0.533 e NOTE Note 2 Note 2 1.270 TYP 10/04/01 R 2325 Orchard Parkway San Jose, CA 95131 TITLE 32J, 32-lead, Plastic J-leaded Chip Carrier (PLCC) DRAWING NO. REV. 32J B 13 0353I-PEEPR-08/09 27.2 32T - TSOP PIN 1 0 ~ 8 c Pin 1 Identifier D1 D L b e L1 A2 E A GAGE PLANE SEATING PLANE COMMON DIMENSIONS (Unit of Measure = mm) A1 MIN NOM MAX A - - 1.20 A1 0.05 - 0.15 A2 0.95 1.00 1.05 D 19.80 20.00 20.20 D1 18.30 18.40 18.50 Note 2 E 7.90 8.00 8.10 Note 2 L 0.50 0.60 0.70 SYMBOL Notes: 1. This package conforms to JEDEC reference MO-142, Variation BD. 2. Dimensions D1 and E do not include mold protrusion. Allowable protrusion on E is 0.15 mm per side and on D1 is 0.25 mm per side. 3. Lead coplanarity is 0.10 mm maximum. L1 0.25 BASIC b 0.17 0.22 0.27 c 0.10 - 0.21 e NOTE 0.50 BASIC 10/18/01 R 14 2325 Orchard Parkway San Jose, CA 95131 TITLE 32T, 32-lead (8 x 20 mm Package) Plastic Thin Small Outline Package, Type I (TSOP) DRAWING NO. REV. 32T B AT28C010 0353I-PEEPR-08/09 AT28C010 Revision History Doc. Rev. Date Comments 0353I 08/2009 Updated AC Charcteristisitics and ordering information. 0353I 07/2009 Add a revision history page and update this version `I' with the changes (AC charactertistics and ordering info from the word file). 15 0353I-PEEPR-08/09 Headquarters International Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Asia Unit 1-5 & 16, 19/F BEA Tower, Millennium City 5 418 Kwun Tong Road Kwun Tong, Kowloon Hong Kong Tel: (852) 2245-6100 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309 78054 Saint-Quentin-enYvelines Cedex France Tel: (33) 1-30-60-70-00 Fax: (33) 1-30-60-71-11 Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Technical Support p_eeprom@atmel.com Sales Contact www.atmel.com/contacts Product Contact Web Site www.atmel.com Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL'S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL'S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel's products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. (c) 2009 Atmel Corporation. All rights reserved. Atmel(R), Atmel logo and combinations thereof, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. 0353I-PEEPR-08/09