REVISION V JW-XX-XX-XX-X-XXX-XXX-XX-X DO NOT SCALE FROM THIS PRINT OPTION -P: PICK & PLACE PAD (USE PPP-47, SEE FIG. 2, SHEET 2) (-VS ONLY, 3 POSITION MIN, .275[6.99] MIN POST HEIGHT) No OF POSITIONS -02 THRU -24 (No OF POS x .156[.3.96]) .010[0.25] LEAD STYLE -04: T-1S8-05-X -05: T-1S8-05-X ((NO OF POS -1) x .156 [3.96]) .005 [.13] OPTION -VS: VERTICAL SURFACE MOUNT PLATING SPECIFICATION -T: MATTE TIN CONTACT AND TAIL -TM: MATTE TIN CONTACT AND TAIL .078 1.97 POST HEIGHT -XXX: SPECIFY POST HEIGHT . 000 MIN (SEE NOTE 3) SPACE OPTION -XXX: SPECIFY BOARD SPACING ROW SPECIFICATION -S: SINGLE (USE HFWJ-24-156) .250 6.35 REF .125 3.18 -S: SINGLE HFWJ-24-156 2 MAX SWAY (EITHER DIRECTION) -VS IN-PROCESS -S IN-PROCESS POST HEIGHT V V 24 V SPACE OPTION 01 V POST HEIGHT 1.350 34.29 REF SPACE OPTION -.100 .265 6.73 MIN (SEE NOTE 3) -VS: VERTICAL SURFACE MOUNT C POST HEIGHT -XXX .008[0.20] (.000 MIN) .045 1.14 SQ. REF C C SPACE OPTION -XXX .008[0.20] (1.080[27.43] MAX, .250[6.35] MIN) .125 3.18 REF T-1S8-05-T NOTES: 1. HEIGHT VARIATION BETWEEN ANY TWO PINS SHALL BE .010[0.25] MAX. 2. MAXIMUM PIN ROTATION IN BODY: 2 . 3. TAIL TO BE SHEARED TO .265[6.73] MIN. A SECOND SHEAR STEP WILL BE NEEDED AFTER FORMING TO ACHIEVE THE TAIL TO TAIL DIM. 4. MAXIMUM BURR ALLOWED: .004[0.10]. 5. MAXIMUM BURR ALLOWED: .0015[0.038]. 6. THROUGH HOLE TO BE BULK PACKAGED. 7. VERTICAL SURFACE MOUNT (-VS) TO BE PACKAGED AS FOLLOWS: POSITIONS -04 THRU -24 ARE TO BE PACKAGED IN TUBES (SEE TABLE 1, SHEET 2); POSITIONS -02 AND -03 ARE TO BE LAYER PACKAGED. 8. MIN PUSHOUT FORCE TO BE 3 LBS. 9. MAX CUT FLASH TO BE .020[0.51]. 10. C REPRESENTS A CRITICAL DIMENSION. .09 2.29 ANGLES .XX: .01 [.3] 2 .XXX: .005 [.13] .XXXX: .0020 [.051] MATERIAL: .008[0.20] .31 7.87 -VS: VERTICAL SURFACE MOUNT -S: SINGLE DECIMALS +4 90 - 0 SEE NOTES 3 & 5 SEE NOTES 3 & 4 UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES. TOLERANCES ARE: C SPACE OPTION -XXX .008[0.20] (1.150[29.21] MAX, .350[8.89] MIN) .225 5.72 1.250 [31.75] MAX PROPRIETARY NOTE THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. DO NOT SCALE DRAWING SHEET SCALE: 1.25:1 INSULATOR: LCP, COLOR: NATURAL TERMINAL: PHOSPHOR BRONZE MAX BOW ALLOWED: .002[0.05] IN/IN F:\DWG\MISC\Mktg\JW-XX-XX-XX-X-XXX-XXX-XX-X-MKT.SLDDRW 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PHONE: 812-944-6733 FAX: 812-948-5047 e-Mail: info@SAMTEC.com code: 55322 DESCRIPTION: .156[3.96] POWER STACKER ASSEMBLY DWG. NO. JW-XX-XX-XX-X-XXX-XXX-XX-X BY: KEVIN B 06/12/2002 SHEET 1 OF 2 REVISION V FIG 2 -P: PICK & PLACE PAD OPTION (-VS ONLY, 3 POS. MIN) NOTE: "R" = No OF POS x .156[3.96] REF "S" = {("R" - .450[11.43]) / 2} .020[12.90] "G" = POST HEIGHT (.275[6.99] MIN) + .050[1.27] REF "R" "S" "G" .300 7.62 REF .450 11.43 REF PROPRIETARY NOTE THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. DO NOT SCALE DRAWING SHEET SCALE: 2.5:1 F:\DWG\MISC\Mktg\JW-XX-XX-XX-X-XXX-XXX-XX-X-MKT.SLDDRW 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PHONE: 812-944-6733 FAX: 812-948-5047 e-Mail: info@SAMTEC.com code: 55322 DESCRIPTION: .156[3.96] POWER STACKER ASSEMBLY DWG. NO. JW-XX-XX-XX-X-XXX-XXX-XX-X BY: KEVIN B 06/12/2002 SHEET 2 OF 2