TGL2206 S-Band 100W VPIN Limiter Applications * Receive Chain Protection * Commercial and Military Radar Product Features * * * * * * * * Frequency Range: 2 - 4.5 GHz Insertion Loss: <0.5 dB Peak Power Handling: 100W (pulsed) Flat Leakage: 15 dBm Return Loss: 15 dB Passive (no DC bias required) Integrated DC Block on output Chip Dimensions: 2.2 x 2.5 x 0.1 mm 2 1 RF In RF Out General Description Pad Configuration The TriQuint TGL2206 is a high power, wideband MMIC GaAs VPIN limiter capable of protecting sensitive receive channel components against high power incident signals. The TGL2206 does not require DC bias and achieves a low insertion loss all in a small form factor. These features allow for simple integration with minimal impact to system performance. Pad No. Symbol 1 2 RF In RF Out The TGL2206 operates from 2 to 4.5 GHz and achieves low insertion loss of 0.5 dB and return loss of 15 dB. It can limit up to 100 W incident pulsed-power with a low flat leakage of 15 dBm. The TGL2206 has a protective surface passivation layer providing environmental robustness and is ideally suited to support both commercial and defense related applications. Lead-free and RoHS compliant. Preliminary Datasheet: Rev - 09-21-13 (c) 2013 TriQuint Ordering Information Part ECCN Description TGL2206 EAR99 S-Band 100W VPIN Limiter - 1 of 7 - Disclaimer: Subject to change without notice www.triquint.com TGL2206 S-Band 100W VPIN Limiter Absolute Maximum Ratings Parameter Recommended Operating Conditions Value Incident Power, CW or Pulsed, 50, 25C 100W Incident Power, CW or Pulsed, 50, 85C 70W Mounting Temperature (30 Seconds) 320 C Storage Temperature -40 to 150C Parameter Value Passive - no bias Electrical specifications are measured at specified test conditions. Specifications are not guaranteed over all recommended operating conditions. Operation of this device outside the parameter ranges given above may cause permanent damage. These are stress ratings only, and functional operation of the device at these conditions is not implied. Electrical Specifications 0 Test conditions unless otherwise noted: 25 C Parameter Operational Frequency Range Insertion Loss Input Return Loss Output Return Loss Flat Leakage Power @ Pin > 30 dBm Insertion Loss Temperature Coefficient Min Typical 2 Max Units 4.5 GHz dB dB dB dBm dB/C < 0.5 15 15 15 0.003 Thermal and Reliability Information Parameter Incident Power - 168hr RF Operational Life Test* Test Conditions Value Units Frequency = 4.5 GHz, CW, 50, 25C 50 W Frequency = 4.5 GHz, Pulsed, PW = 10us, DC = 10%, 50, 25C 100 W *Test was terminated at 168 Hrs. Insertion Loss remained 1 dB for device under test. Preliminary Datasheet: Rev - 09-21-13 (c) 2013 TriQuint - 2 of 7 - Disclaimer: Subject to change without notice www.triquint.com TGL2206 S-Band 100W VPIN Limiter Typical Performance Insertion Loss vs. Frequency vs. Temp S-Parameters vs. Frequency +25C 0.0 0.4 5 0.5 0.8 10 1.2 15 20 IL IRL 2.0 Return Loss (dB) Insertion Loss (dB) 1.6 Insertion Loss (dB) 0 0.0 25 ORL 2.4 2 3 4 Frequency (GHz) 5 1.0 -40C +25C +85C 1.5 2.0 2.5 3.0 30 1 Temp varies 1 6 CW, +25 0C 15.5 15.0 15.0 Pout (dBm) Pout (dBm) 5 6 Pulse: PW = 1ms, DC = 10%, +25 0C 16.0 15.5 14.5 2.1 GHz 14.0 3 4 Frequency (GHz) Output Power vs. Pin vs. Frequency Output Power vs. Pin vs. Frequency 16.0 2 2.5 GHz 14.5 3.0 GHz 3.5 GHz 14.0 3.7 GHz 3.0 GHz 13.5 13.5 3.5 GHz 3.7 GHz 13.0 13.0 30 32 34 36 38 40 42 Pin (dBm) 44 46 48 30 50 Output Power vs. Pin vs. Frequency 15.0 15.0 Pout (dBm) Pout (dBm) 15.5 14.5 2.1 GHz 2.5 GHz 38 40 42 Pin (dBm) 44 46 48 50 CW, +85 0C 14.5 2.1 GHz 14.0 2.5 GHz 3.0 GHz 13.5 36 16.0 15.5 14.0 34 Output Power vs. Pin vs. Frequency CW, -40 0C 16.0 32 3.0 GHz 13.5 3.5 GHz 3.5 GHz 3.7 GHz 3.7 GHz 13.0 13.0 30 32 34 36 38 40 42 Pin (dBm) Preliminary Datasheet: Rev - 09-21-13 (c) 2013 TriQuint 44 46 48 50 29 - 3 of 7 - 31 33 35 37 39 41 Pin (dBm) 43 45 47 49 Disclaimer: Subject to change without notice www.triquint.com TGL2206 S-Band 100W VPIN Limiter Typical Performance Spike Leakage PW = 0.1 ms, DC = 10%, Freq = 3.5 GHz, +25 0C 16 Pout (dBm) 15 14 13 Pin = 30 dBm Pin = 35 dBm Pin = 40 dBm Pin = 45 dBm Pin = 50 dBm 12 11 10 0 Preliminary Datasheet: Rev - 09-21-13 (c) 2013 TriQuint 1 2 3 Time (us) - 4 of 7 - 4 5 Disclaimer: Subject to change without notice www.triquint.com TGL2206 S-Band 100W VPIN Limiter Assembly Drawing Mechanical Drawing 2 1 Unit: millimeters Thickness: 0.10 Die x, y size tolerance: 0.050 Chip edge to bond pad dimensions are shown to center of pad Ground is backside of die Pad Number 1 2 Symbol Description Pad Size RF In RF Out Input; matched to 50 . Output; matched to 50 . 0.100 x 0.200 0.100 x 0.200 Preliminary Datasheet: Rev - 09-21-13 (c) 2013 TriQuint - 5 of 7 - Disclaimer: Subject to change without notice www.triquint.com TGL2206 S-Band 100W VPIN Limiter Assembly Notes Component placement and adhesive attachment assembly notes: * Vacuum pencils and/or vacuum collets are the preferred method of pick up. * Air bridges must be avoided during placement. * The force impact is critical during auto placement. * Solder or Organic Adhesive attachment can be used for TGL2205. * Curing should be done in a convection oven; proper exhaust is a safety concern. Solder attachment reflow process assembly notes: * Use AuSn (80/20) solder and limit exposure to temperatures above 300C to 3-4 minutes, maximum. * An alloy station or conveyor furnace with reducing atmosphere should be used. * Do not use any kind of flux. * Coefficient of thermal expansion matching is critical for long-term reliability. * Devices must be stored in a dry nitrogen atmosphere. Organic adhesive attachment assembly notes: * The organics such as epoxy or polyimide can be used. * Epoxies cure at temperatures of 100C to 200C. Interconnect process assembly notes: * Thermosonic ball bonding is the preferred interconnect technique. * Force, time, and ultrasonics are critical parameters. * Aluminum wire should not be used. * Devices with small pad sizes should be bonded with 0.0007-inch wire. Preliminary Datasheet: Rev - 09-21-13 (c) 2013 TriQuint - 6 of 7 - Disclaimer: Subject to change without notice www.triquint.com TGL2206 S-Band 100W VPIN Limiter Product Compliance Information ESD Sensitivity Ratings Solderability Caution! ESD-Sensitive Device This part is compliant with EU 2002/95/EC RoHS directive (Restrictions on the Use of Certain Hazardous Substances in Electrical and Electronic Equipment). This product also has the following attributes: * Lead Free * Halogen Free (Chlorine, Bromine) * Antimony Free * TBBP-A (C15H12Br402) Free * PFOS Free * SVHC Free ESD Rating: TBD Value: TBD Test: Human Body Model (HBM) Standard: JEDEC Standard JESD22-A114 ECCN US Department of Commerce: EAR99 Contact Information For the latest specifications, additional product information, worldwide sales and distribution locations, and information about TriQuint: Web: www.triquint.com Email: info-sales@triquint.com Tel: Fax: For technical questions and application information: +1.972.994.8465 +1.972.994.8504 Email: info-products@triquint.com Important Notice The information contained herein is believed to be reliable. TriQuint makes no warranties regarding the information contained herein. TriQuint assumes no responsibility or liability whatsoever for any of the information contained herein. TriQuint assumes no responsibility or liability whatsoever for the use of the information contained herein. The information contained herein is provided "AS IS, WHERE IS" and with all faults, and the entire risk associated with such information is entirely with the user. All information contained herein is subject to change without notice. Customers should obtain and verify the latest relevant information before placing orders for TriQuint products. The information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by such information. TriQuint products are not warranted or authorized for use as critical components in medical, life-saving, or lifesustaining applications, or other applications where a failure would reasonably be expected to cause severe personal injury or death. Preliminary Datasheet: Rev - 09-21-13 (c) 2013 TriQuint - 7 of 7 - Disclaimer: Subject to change without notice www.triquint.com Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Qorvo: TGL2206