REGULATORY COMPLIANCE (Data Sheet downloaded on Jan 19, 2018)
2011/65 +
2015/863 174 SVHC
EC3700ETTTS-100.000M TR
ITEM DESCRIPTION
Quartz Crystal Clock Oscillators XO (SPXO) LVCMOS (CMOS) 2.5Vdc 4 Pad 3.2mm x 5.0mm Ceramic Surface Mount (SMD)
100.000MHz ±100ppm -40°C to +85°C
ELECTRICAL SPECIFICATIONS
Nominal Frequency 100.000MHz
Frequency Tolerance/Stability ±100ppm Maximum (Inclusive of all conditions: Calibration Tolerance at 25°C, Frequency Stability over the Operating
Temperature Range, Supply Voltage Change, Ouput Load Change, First Year Aging at 25°C, Shock, and Vibration)
Operating Temperature Range -40°C to +85°C
Supply Voltage 2.5Vdc ±5%
Input Current 13mA Maximum
Output Voltage Logic High (Voh) 90% of Vdd Minimum (IOH = -4mA)
Output Voltage Logic Low (Vol) 10% of Vdd Maximum (IOL = +4mA)
Rise/Fall Time 3nSec Maximum (Measured at 20% to 80% of waveform)
Duty Cycle 50 ±5(%) (Measured at 50% of waveform)
Load Drive Capability 15pF Maximum
Output Logic Type CMOS
Pin 1 Connection Tri-State (High Impedance)
Tri-State Input Voltage (Vih and Vil) 90% of Vdd Minimum or No Connect to Enable Output, 10% of Vdd Maximum to Disable Output (High Impedance)
Standby Current 10µA Maximum (Disabled Output: High Impedance)
RMS Phase Jitter 1pSec Maximum (12kHz to 20MHz offset frequency)
Start Up Time 10mSec Maximum
Storage Temperature Range -55°C to +125°C
ENVIRONMENTAL & MECHANICAL SPECIFICATIONS
ESD Susceptibility MIL-STD-883, Method 3015, Class 1, HBM: 1500V
Fine Leak Test MIL-STD-883, Method 1014, Condition A
Flammability UL94-V0
Gross Leak Test MIL-STD-883, Method 1014, Condition C
Mechanical Shock MIL-STD-883, Method 2002, Condition B
Moisture Resistance MIL-STD-883, Method 1004
Moisture Sensitivity J-STD-020, MSL 1
Resistance to Soldering Heat MIL-STD-202, Method 210, Condition K
Resistance to Solvents MIL-STD-202, Method 215
Solderability MIL-STD-883, Method 2003
Temperature Cycling MIL-STD-883, Method 1010, Condition B
Vibration MIL-STD-883, Method 2007, Condition A
www.ecliptek.com | Specification Subject to Change Without Notice | Revision I 03/12/2015 | Page 1 of 5
Ecliptek, LLC 5458 Louie Lane, Reno, NV 89511 1-800-ECLIPTEK or 714.433.1200
EC3700ETTTS-100.000M TR
MECHANICAL DIMENSIONS (all dimensions in millimeters)
3.20
±0.20
5.00
±0.20
1.3
MAX
1.20
±0.20 (x4)
1.00 ±0.20 (x4)
1.20 ±0.20
2.54
±0.15
MARKING
ORIENTATION
3
4
1
2
PIN CONNECTION
1 Tri-State
2 Ground
3 Output
4 Supply Voltage
LINE MARKING
1E100.00
E=Ecliptek Designator
2XXXXX
XXXXX=Ecliptek
Manufacturing Identifier
All Tolerances are ±0.1
Suggested Solder Pad Layout
Solder Land
(X4)
All Dimensions in Millimeters
1.14
1.00
1.20 (X4)
1.40 (X4)
www.ecliptek.com | Specification Subject to Change Without Notice | Revision I 03/12/2015 | Page 2 of 5
Ecliptek, LLC 5458 Louie Lane, Reno, NV 89511 1-800-ECLIPTEK or 714.433.1200
EC3700ETTTS-100.000M TR
OUTPUT DISABLE
(HIGH IMPEDANCE
STATE)
OUTPUT WAVEFORM & TIMING DIAGRAM
VOH
VOL
80% of Waveform
50% of Waveform
20% of Waveform
Fall
Time
Rise
Time TW
T
Duty Cycle (%) = TW/T x 100
VIH
VIL
tPLZ tPZL
CLOCK OUTPUT TRI-STATE INPUT
www.ecliptek.com | Specification Subject to Change Without Notice | Revision I 03/12/2015 | Page 3 of 5
Ecliptek, LLC 5458 Louie Lane, Reno, NV 89511 1-800-ECLIPTEK or 714.433.1200
EC3700ETTTS-100.000M TR
Supply
Voltage
(VDD)
Test Circuit for CMOS Output
Output
No Connect
or Tri-State
Ground
+ +
+_
__
Power
Supply 0.01µF
(Note 1) 0.1µF
(Note 1) CL
(Note 3)
Note 1: An external 0.1µF low frequency tantalum bypass capacitor in parallel with a 0.01µF high frequency
ceramic bypass capacitor close to the package ground and VDD pin is required.
Note 2: A low capacitance (<12pF), 10X attenuation factor, high impedance (>10Mohms), and high bandwidth
(>300MHz) passive probe is recommended.
Note 3: Capacitance value CL includes sum of all probe and fixture capacitance.
Voltage
Meter
Current
Meter
Oscilloscope Frequency
Counter
Probe
(Note 2)
www.ecliptek.com | Specification Subject to Change Without Notice | Revision I 03/12/2015 | Page 4 of 5
Ecliptek, LLC 5458 Louie Lane, Reno, NV 89511 1-800-ECLIPTEK or 714.433.1200
PART NUMBER DATA SHEET
Tape & Reel Dimensions
All Dimensions in Millimeters
Compliant to EIA-481
DIA 50 MIN
DIA 20.20 MIN
DIA 13.00 ±0.20
2.50 MIN Width
10 MIN Depth
Tape slot in Core
for Tape Start
DIA 40 MIN
Access Hole at
Slot Location
1.50 MIN
Direction of Unreeling
MARKING
ORIENTATION
EC3700ETTTS-100.000M TR
16.00 ±0.30
7.50 ±0.10
DIA 1.50 MIN
4.00 ±0.10
2.00 ±0.10
8.00 ±0.10 A0
DIA 1.50 +0.10/-0.00
1.75 ±0.10
B0
0.60 MAX
0.10 MAX
K0
22.40 MAX
Quantity Per Reel: 1,000 units
180 MAX
16.40 +2.00/-0.00
www.ecliptek.com | Specification Subject to Change Without Notice | Revision I 03/12/2015 | Page 5 of 5
Ecliptek, LLC 5458 Louie Lane, Reno, NV 89511 1-800-ECLIPTEK or 714.433.1200
