A M I C R O S E M I LX8815 Dual Channel 1A Low Dropout Regulator C O M P A N Y P RELIMINARY The LX8815 is a dual channel positive-voltage linear regulator. This dual regulator has either one fixed output coupled with an adjustable output or two fixed outputs. Each channel features low-dropout and high accuracy. The LX8815 provides designers with a flexible power management solution, minimal printed circuit board area, and shorter design cycles. Each channel can supply up to one amp independently with a regulator design optimized for system efficiency by consuming minimal ground current and directing quiescent current to the load. The LX8815 features on-chip trimming of the internal voltage reference enabling precise output voltages, typically 1% of it's specified value, while the BiPolar output transistor has a low dropout voltage even at full output current (VDO < 1.1V typ. @ 1A). Thermal and Short Circuit Current Protection are integrated on-chip and operate independently for each regulator output. The LX8815 regulator is stable with a low-value output capacitor, typically 3.3F tantalum or 4.7F ceramic on the outputs, allowing designers flexibility in external component selection. Linfinity's S-PAK power package offers maximum power dissipation and ease of assembly using surface mount technology. IMPORTANT: For the most current data, consult MICROSEMI's website: http://www.microsemi.com Two Independent Regulated Outputs Accurate Output Voltages Max. Dropout of 1.1V at Rated Current Independent Thermal and Current Limit Protection Low Profile 5 Lead SMT Power Package Low Tolerance Line (0.2%) and Load (0.4%) Regulation Wide DC Supply Voltage of 4.0V W W W . Microsemi . COM to 12.0V Loop Stability Independent of Output Capacitor Type 5V to 3.3V Linear Regulator Low Voltage Logic Supplies Active SCSI Terminators Battery Charging Circuits Instrumentation PC Peripherals V IN 1 R3 0.1 + - C1 10F BIAS VOUT1 5 C2 4.7F 1.25V VREF + - R VOUT 2 = 1.25 x 1 + 1 + I ADJ x R2 R2 VOUT2 4 C3 4.7F 2 GND Adjustable or Fixed 3 R2 Note: Application circuit above using ceramic capacitors, C 1 requires R 3 (0.075 to 0.3). For Tantalum capacitors: R 3 is not used a n d C 1, C 2, and C 3 > 2 F. R1 and R2 used with LX88xx-xx only. Copyright 2000 Rev. 0.2a, 2000-11-20 Microsemi Linfinity Microelectronics Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 1 LX 8 8 1 5 R1 A M I C R O S E M I LX8815 Dual Channel 1A Low Dropout Regulator C O M P A N Y P RELIMINARY TJ (C) OUTPUT V1 OUTPUT V2 0 to 125 3.3V 3.3V 3.3V 2.85V 2.5V 2.5V 1.8V Adj Adj Adj W W W . Microsemi . COM DF Plastic S-PAK 5-PIN LX8815-3325CDF LX8815-3318CDF LX8815-3300CDF LX8815-2800CDF LX8815-2500CDF Note: Available in Tape & Reel. Append the letter "T" to the part number. (i.e. LX8815-3325CDFT) Input Voltage (VBAT)..................................................................................................13.5V Load Current (Internally Limited)................................................................................... 1A Power Dissipation ................................................................................... Internally Limited Short-Circuit Protection ....................................................................................... Indefinite Operating Junction Temperature ................................................................................150C Lead Temperature (Soldering 180 seconds) ...............................................................235C Note: TAB is GND Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of specified terminal. 5 V OUT1 4 V OUT2 3 GND 2 ADJ 1 V IN DF P A C K A G E (Top View) DF PACKAGE THERMAL RESISTANCE-JUNCTION TO TAB, JT THERMAL RESISTANCE-JUNCTION TO AMBIENT, 4.5C/W 24.5C/W JA Junction Temperature Calculation: TJ = TA + (PD x JA). The JA numbers are guidelines for the thermal performance of the device/pc-board system. All of the above assume no ambient airflow. JA can vary from 20C/W to > 40C/W depending on mounting technique. (See Application Notes Section: Thermal considerations) VIN Unregulated input voltage supply. ADJ Adjust control pin for regulator 2 GND Common terminal for ground reference VOUT1 Fixed voltage regulator output (Regulator #1) VOUT2 Fixed or adjustable regulator output (Regulator #2) Copyright 2000 Rev. 0.2a, 2000-11-20 Microsemi Linfinity Microelectronics Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 PACKAGE DATA Page 2 A M I C R O S E M I C O M P A N Y LX8815 Dual Channel 1A Low Dropout Regulator P RELIMINARY Parameter Symbol * LX8815-2800 VIN = 5V, IOUT = 5mA, TJ = 25C 5mA < I1 < 1A, 4.50V < VIN < 10V VIN = 5V, IOUT = 5mA, TJ = 25C 5mA < I1 < 1A, 4.50V < VIN < 10V VIN = 5V, IOUT = 5mA, TJ = 25C 5mA < I1 < 1A, 4.50V < VIN < 10V 4.75V < VIN < 10V, IOUT = 5mA 5mA < I1 < 1A, VIN = 4.75V ILOAD = 1A, V1 = -2% (VIN - V1) = 5V Note 1 3.250 3.234 2.807 2.793 2.462 2.450 VIN = 5V, IOUT = 10mA, TJ = 25C 5mA < I1 < 1A, 4.50V < VIN < 10V VREF(VIN) 4.75V < VIN < 10V, IOUT = 5mA VREF(I2) 5mA < I1 < 1A, VIN = 4.75V V VIN > 4.5V, ILOAD = 1A, V1 = -1% IOUT (MAX) (VIN - V1) = 5V IL Note 1 IADJ 1.238 1.231 V1 * LX8815-2500 Line Regulation Load Regulation Dropout Voltage Current Limit Minimum Load Current Units V1(VIN) V1(I1) V IOUT (MAX) IL 1.0 3.300 3.300 2.850 2.850 2.500 2.500 0.01 0.01 1.1 1.4 0 3.350 3.366 2.893 2.907 2.537 2.550 0.2 0.4 1.25 1.250 1.250 0.01 0.01 1.1 1.4 1 1 1.262 1.269 0.2 0.4 1.3 1.8 75 0.003 140 5 2 V %V1 %V1 V A mA ADJUSTABLE OUTPUT Reference Voltage VREF Line Regulation Load Regulation Dropout Voltage Current Limit Minimum Load Current Adjust Pin Bias Current LX8815-xx00 Min Typ Max FIXED OUTPUT Output Voltage * LX8815-3300 Test Conditions W W W . Microsemi . COM Unless otherwise specified, the following specifications apply over the operating ambient temperature 0C TA 125C except where otherwise noted and the following test conditions: VIN = 5V, IOUT = 10mA, C1 = 4.7F (Tantalum), C2 = 4.7F (Tantalum), and TJ = TA 25C using low duty cycling methods. 1.0 3 5 V %V1 %V1 V A mA A ENTIRE REGULATOR Quiescent Current Ripple Rejection RMS Output Noise (% of VOUT) Thermal Shutdown IQ PSRR VOUT (RMS) TJSD VIN < 10V, I1 = 5mA, I2 = 5mA f=120Hz, VIN = 5V 10Hz < f < 10kHz 60 mA dB %V1 C Note 1: Minimum load current is defined as the amount of output current required to maintain regulation. ELECTRICALS Copyright 2000 Rev. 0.2a, 2000-11-20 Microsemi Linfinity Microelectronics Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 3 A M I C R O S E M I C O M P A N Y LX8815 Dual Channel 1A Low Dropout Regulator P RELIMINARY Unless otherwise specified, the following specifications apply over the operating ambient temperature 0C TA 125C except where otherwise noted and the following test conditions: VIN = 5V, IOUT = 10mA, C1 = 4.7F (Tantalum), C2 = 4.7F (Tantalum), and TJ = TA 25C using low duty cycling methods. Parameter V1 Line Regulation Load Regulation Dropout Voltage Current Limit Minimum Load Current V1(VIN) V1(I1) V IOUT (MAX) IL LX8815-33xx Min Typ Max Units VIN = 5V, IOUT = 5mA, TJ = 25C 5mA < I1 < 1A, 4.50V < VIN < 10V 4.75V < VIN < 10V, IOUT = 5mA 5mA < I1 < 1A, VIN = 4.75V ILOAD = 1A, V1 = -2% (VIN - V1) Note 1 3.250 3.234 VIN = 5V, IOUT = 5mA, TJ = 25C 5mA < I1 < 1A, 4.50V < VIN < 10V VIN = 5V, IOUT = 5mA, TJ = 25C 5mA < I1 < 1A, 4.50V < VIN < 10V 4.75V < VIN < 10V, IOUT = 5mA 5mA < I1 < 1A, VIN = 4.75V VIN > 4.5V, ILOAD = 1A, V1 = -1% (VIN - V1) Note 1 2.462 2.450 1.773 1.764 1.0 3.300 3.300 0.3 0.8 1.1 1.4 0 3.350 3.366 5.0 10 1.25 2.50 2.50 1.80 1.80 0.02 0.04 1.1 1.4 1 2.537 2.550 1.827 1.36 0.15 0.3 1.3 1.8 75 0.003 140 7 2 V mV mV V A mA FIXED OUTPUT 2 Output Voltage * LX8815-3325 V1 * LX8815-3318 Line Regulation Load Regulation Dropout Voltage Current Limit Minimum Load Current Test Conditions FIXED OUTPUT 1 Output Voltage Symbol W W W . Microsemi . COM V1(VIN) V1(I1) V IOUT (MAX) IL 1.0 2 V %mV %mV V A mA ENTIRE REGULATOR Quiescent Current IQ VIN < 10V, I1 = 5mA, I2 = 5mA Ripple Rejection PSRR f=120Hz, VIN = 5V RMS Output Noise (% of VOUT) VOUT (RMS) 10Hz < f < 10kHz Thermal Shutdown TJSD Note 1: Minimum load current is defined as the amount of output current required to maintain regulation. 60 mA dB %V1 C ELECTRICALS Copyright 2000 Rev. 0.2a, 2000-11-20 Microsemi Linfinity Microelectronics Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 4 A M I C R O S E M I LX8815 Dual Channel 1A Low Dropout Regulator C O M P A N Y P RELIMINARY Dim A C I D B K H J F G E A B C D E F G H I J K MILLIMETERS MIN MAX 9.27 9.52 8.89 9.14 1.77 2.03 7.49 7.74 0.12 0.38 0.58 0.84 1.70 BSC 0.79 1.04 4.31 6.86 0.03 0.13 10.41 10.67 INCHES MIN MAX .365 .375 .350 .360 .070 .080 .295 .305 .005 .015 .023 .033 0.067 BSC .031 .041 .170 .270 .001 .005 .410 .420 W W W . Microsemi . COM Note: 1. Dimensions do not include mold flash or protrusions; these shall not exceed 0.155mm(.006") on any side. Lead dimension shall not include solder coverage. MECHANICALS Preliminary Data - Information contained in this document is pre-production data and is proprietary to LinFinity. It may not be modified in any way without the express written consent of LinFinity. Product referred to herein is offered in sample form only and LinFinity reserves the right to change or discontinue this proposed product at any time. Copyright 2000 Rev. 0.2a, 2000-11-20 Microsemi Linfinity Microelectronics Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 5