High Speed Type Photocoupler 6N135 / 6N136 Series Features Package Dimensions High speed response tPHL, tPLH ( 6N135 MAX. 1.5 s at RL=4.1k ) ( 6N136 MAX. 0.8 s at RL=1.9k ) High common mode rejection voltage ( CMH : TYP. 1kV / s) Options Available : - Leads with 0.4" (10.16mm) Spacing (M Type) - Lead Bends for Surface Mounting (S Type) - Tape and Reel of Type I for SMD (Add "-TA" Suffix) - Tape and Reel of Type II for SMD (Add "-TA1" Suffix) - VDE 0884 Approvals (Add "-V" Suffix) Y R A N I M I L E R P 1. Computers, measuring instruments, control equipment 2. High speed line receivers, high speed logic 3. Telephone sets 4. Signal transmission between circuits of different potentials and impedances NOTES : 1. Year date code. 2. 2-digit work week. 3. Factory code shall be marked (Z Taiwan, Y Thailand). 4. Model No.: 6N135 ; 6N136 5. All dimensions are in millimeters (inches). 6. Tolerance is 0.25mm (.010") unless otherwise noted. 7. Specifications are subject to change without notice. Ordering Information Part Number Application part number Package 6N135 6N135M 6N135S 6N135S-TA 6N135S-TA1 8-pin DIP 8-pin (leads with 0.4" spacing) 8-pin (lead bends for surface mount) 8-pin (tape and reel packaging of type I) 8-pin (tape and reel packaging of type II) 6N136 6N136M 6N136S 6N136S-TA 6N136S-TA1 6N135-V 6N135M-V 6N135S-V 6N135STA-V 6N135STA1-V 6N136-V 6N136M-V 6N136S-V 6N136STA-V 6N136STA1-V 8-pin DIP 8-pin (leads with 0.4" spacing) 8-pin (lead bends for surface mount) 8-pin (tape and reel packaging of type 8-pin (tape and reel packaging of type 8-pin DIP 8-pin (leads with 0.4" spacing) 8-pin (lead bends for surface mount) 8-pin (tape and reel packaging of type 8-pin (tape and reel packaging of type 8-pin DIP 8-pin (leads with 0.4" spacing) 8-pin (lead bends for surface mount) 8-pin (tape and reel packaging of type 8-pin (tape and reel packaging of type PHOTOCOUPLER Applications 6N135 6N136 I) II) 6N135 I) II) 6N136 I) II) 12-133 Ratings and Characteristics Absolute Maximum Ratings (Ta=25 Symbol Rating Unit Forward Current IF 25 mA Reverse Voltage VR 5 V Power Dissipation P 45 mW Supply Voltage VCC -0.5~+15 V Output Voltage VO -0.5~+15 V VEBO 5 V Average Output Current IO 8 mA Peak Output Current I OP 16 mA Parameter Input Emitter-base Reverse Withstand Voltage (pin 5 to 7) Output Y R A N I M I L E R P Base Current (Pin 7) IB 5 mA PO 100 mW Vrms Power Dissipation *1.Isolation Voltage V iso 2,500 Operating Temperature Topr -55~+100 Storage Temperature Tstg -55~+125 Tsol 260 *2.Soldering Temperature ) *1. AC for 1 minute, R.H. = 40 ~ 60% Isolation voltage shall be measured using the following method. (1) Short between anode and cathode on the primary side and between collector and emitter on the secondary side. (2) The isolation voltage tester with zero-cross circuit shall be used. (3) The waveform of applied voltage shall be a sine wave. *2. For 10 seconds Electrical / Optical Characteristics Parameter ( Ta = 0 ~ +70 Symbol Input Forward Voltage Temperature Coefficient VF / Input Reverse Current BVR Input Capacitance CIN *1 Current Transfer Ratio Min. VF Input Forward Voltage Ta unless otherwise specified ) Typ. Max. unit 1.8 1.95 V -1.9 mV/ 5.0 IF=16mA V Ta=25 60 pF VF=0, f=1MHz , IR=10 A 6N135 CTR(1) 7.0 30 % 6N136 CTR(1) 19 40 % Ta=25 , IF=16mA VO=0.4V, VCC=4.5V 6N135 CTR(2) 5.0 33 % IF=16mA, VO=0.5V 6N136 CTR(2) 15 43 % VCC=4.5V IF=16mA VCC=4.5V IO=1.1mA Ta=25 , IF=0 VCC=VO=5.5V Ta=25 , IF=0 VCC=VO=15V Logic (0) Output Voltage Logic (1) Output Current Logic (0) Output Voltage VOL 0.1 0.4 V IOH(1) 3.0 500 nA IOH(2) 0.01 1.0 A IOH(3) 50 A I CCL 200 A 1.0 A 2.0 A ICCH(1) 0.02 Logic (1) Output Current ICCH(2) *2 Isolation Resistance (Input-Output) RI-O 1012 Capacitance (Input-Output) CI-O 0.6 Transistor Current Amplification Factor hFE 150 *1. Current transfer ratio is the ratio of input current and output current expressed in %. *2. Measured as 2-pin element ( Short 1, 2, 3, 4 and 5, 6, 7, 8 ) 12-134 Conditions Ta=25 , IF=16mA pF IF=0, VCC=VO=15V IF=16mA, VCC=15V VO=open Ta=25 , VCC=15V VO=open, IF=0 VCC=15V VO=open, IF=0 VI-O=500VDC f=1MHz VO=5V, IO=3mA Electrical / Optical Characteristics Parameter Symbol 6N135 *3 Propagation Delay time Output 6N136 *4 Instantaneous common mode rejection voltage output(1) *5 Instantaneous common mode rejection voltage output(0) *7 Bandwidth ( Ta = 25 Min. Typ. Max. unit t PHL 0.2 1.5 t PLH 1.1 1.5 t PHL 0.2 0.8 t PLH 0.5 0.8 CMH 1000 V/ s CML -1000 V/ s BW 2.0 VCC = 5V, IF = 16mA ) Conditions s RL=4.1k s RL=1.9K MHz IF=0, VCM=10VP-P RL=*6 VCM=10VP-P IF=16mA , RL=*6 RL=100 Y R A N I M I L E R P PHOTOCOUPLER *3 RL = 4.1k is equivalent to one LSTTL and 6.1k pull-up resistor. *4 Instantaneous common mode rejection voltage "output (1)" represents a common mode voltage variation that can hold the output above (1) level (Vo>2.0V). *5 Instantaneous common mode rejection voltage "output (0)" represents a common mode voltage variation that can hold the output above (0) level (Vo<0.8V). *6 6N135 : RL=4.1k 6N136 : RL=1.9k *7 Bandwidth represents a point where AC input goes down by 3dB. 12-135 Typical Electrical/Optical Characteristic Curves (25 Ambient Temperature Unless Otherwise Noted) Y R A N I M I L E R P 12-136 PHOTOCOUPLER Y R A N I M I L E R P 12-137