VNQ86013TR-E - STMicroelectronics, Inc.

September 2010 Doc ID 10964 Rev 6 1/19

VNQ860-E

VNQ860SP-E

Quad channel high side driver

Features

■CMOS compatible I/Os

■Undervoltage and overvoltage shutdown

■Shorted load protection

■Thermal shutdown

■Very low standby current

■Protection against loss of ground

Description

The VNQ860-E, VNQ860SP-E are monolithic

devices made using STMicroelectronics VIPower

M0-3 technology, intended for driving any kind of

load with one side connected to ground. Active

current limitation combined with thermal

shutdown and automatic restart protect the device

against overload. Device automatically turns OFF

in case of ground pin disconnection. This device

is especially suitable for industrial applications in

norms conformity with IEC 61131,

(Programmable controllers international

standard).

Type RDS(on)(1)

1. Per each channel

Iout VCC

VNQ860-E

VNQ860SP-E 270 mΩ0.25 A 36 V

SO 20 PowerSO-10TM

Figure 1. Block diagram

www.st.com

Contents VNQ860-E, VNQ860SP-E

2/19 Doc ID 10964 Rev 6

Contents

1 Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2 Pin connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

4 Truth table and switching characteristics . . . . . . . . . . . . . . . . . . . . . . . . 7

5 Typical application schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

6 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

7 PowerSO-10™ thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

8 Reverse polarity protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

9 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

10 Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

11 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

VNQ860-E, VNQ860SP-E Maximum rating

Doc ID 10964 Rev 6 3/19

1 Maximum rating

Table 1. Absolute maximum rating

Symbol Parameter

Value

Unit

SO20 PowerSO-10

VCC DC supply voltage 41 V

-VCC Reverse DC supply voltage -0.3 V

-IGND DC reverse ground pin -200 mA

IOUT DC output current Internally limited A

-IOUT Reverse DC output current -2 A

IIN DC input current ± 10 mA

VIN Input voltage range -3/+VCC V

ISTAT DC status voltage + VCC V

VESD Electrostatic discharge (R = 1.5 kΩ; C = 100 pF) 2000 V

Ptot Power dissipation at Tc <= 25 °C 16 90 W

TJJunction operating temperature Internally limited °C

TcCase operating temperature -40 to 150 °C

Tstg Storage temperature -55 to 150 °C

Table 2. Thermal data

Symbol Parameter

Values

Unit

SO20 PowerSO-10

RthJP Thermal resistance junction-pins Max 8 - °C/W

RthJA Thermal resistance junction-ambient Max 58 52 (1)

1. When mounted on FR4 printed circuit board with 0.5 cm2 of copper area (at least 35µ thick) connected to

all VCC pins.

°C/W

37 (2)

2. When mounted on FR4 printed circuit board with 6 cm2 of copper area (at least 35µ thick) connected to all

VCC pins.

RthJC Thermal resistance junction-case Max - 1.4 °C/W

Pin connection VNQ860-E, VNQ860SP-E

4/19 Doc ID 10964 Rev 6

2 Pin connection

Figure 2. Configuration diagram (top view)

Figure 3. Current and voltage conventions

Table 3. Pin connection

Connection / pin Status N.C. Output Input

Floating X X X X

To ground X Through 10 kΩ resistor

VNQ860-E, VNQ860SP-E Electrical characteristics

Doc ID 10964 Rev 6 5/19

3 Electrical characteristics

8 V < VCC < 36 V; -40 °C < TJ < 150 °C; unless otherwise specified.

Table 4. Power section

Symbol Parameter Test conditions Min. Typ. Max. Unit

VCC

Operating supply

voltage 5.5 36 V

VUSD Undervoltage shutdown 3 4 5.5 V

VOV Overvoltage shutdown 36 42 48 V

RON

On state resistance

(per channel)

IOUT = 0.25 A; TJ = 25 °C;

IOUT = 0.25 A;

270

540 mΩ

ISSupply current

OFF state; VCC = 24 V;

TC = 25 °C

ON state (all channels ON)

120

µA

ILGND Output current

VCC - VSTAT = VIN =

VGND = 24 V;

VOUT = 0 V

1mA

IL(OFF)

OFF state output

current VIN = VOUT = 0 V 0 10 µA

IOUTleak

OFF state output

leakage current

VIN = VGND = 0 V;

VCC = VOUT = 24 V; TA = 25 °C 240 µA

IOUTleak

OFF state output

leakage current

VIN = VGND = 0 V; VCC = 24 V;

VOUT = 10 V; TA = 25 °C 100 µA

Table 5. Switching (VCC = 24 V)

Symbol Parameter Test conditions Min. Typ. Max. Unit

t(ON)

Turn-on delay time of

Output current

RL = 96 Ω from VIN rising edge

to VOUT = 2.4 V -10-µs

t(OFF)

Turn-off delay time of

Output current

RL = 96 Ω from VIN rising edge

to VOUT = 21.6 V -40-µs

(dVOUT/dt)on Turn-on voltage slope RL = 96 Ω from VOUT = 2.4 V to

19.2 V -0.75-V/µs

(dVOUT/dt)off Turn-off voltage slope RL = 96 Ω from VOUT = 21.6 V to

2.4 V -0.25-V/µs

Electrical characteristics VNQ860-E, VNQ860SP-E

6/19 Doc ID 10964 Rev 6

Table 6. Protections (per channel)

Symbol Parameter Test conditions Min. Typ. Max. Unit

Ilim Current limitation 0.35 0.7 1.1 A

T(hyst) Thermal hysteresis 7 15 °C

TTSD

Thermal shutdown

temperature 150 175 200 °C

TRReset temperature 135 °C

Vdemag

Turn-off output clamp

voltage IOUT = 0.25 A, VCC = 24 V VCC-

VCC-

47 V

Table 7. Logical input (per channel)

Symbol Parameter Test conditions Min. Typ. Max. Unit

VIL Low level input voltage - 1.25 V

IIL Low level input current VIN = 1.25 V 1 - µA

VIH

High level input

voltage 3.25 - V

IIH

High level input

current VIN = 3.25 V - 10 µA

VI(HYST)

Input hysteresis

voltage 0.5 - V

IIN Input current VIN = VCC = 36 V - 200 µA

VOL I/O output voltage IIN = 5 mA (fault condition) - 1 V

Table 8. Status pin

Symbol Parameter Test conditions Min. Typ. Max. Unit

VSTAT

Status low output

voltage ISTAT = 5 mA (fault condition) - - 1 V

ILSTAT

Status leakage

current

Normal operation;

VSTAT = VCC = 36 V --10µA

CSTAT

Status pin input

capacitance

Normal operation;

VSTAT = 5 V --100pF

Table 9. VCC - output diode

Symbol Parameter Test conditions Min. Typ. Max. Unit

VFForward on voltage -IOUT = 0.3 A; TJ = 150 °C - - 1 V

VNQ860-E, VNQ860SP-E Truth table and switching characteristics

Doc ID 10964 Rev 6 7/19

4 Truth table and switching characteristics

Figure 4. Switching characteristics

Table 10. Truth table

Conditions MCOUTn I/On OUTPUTn STATUS

Normal operation L

Current limitation L

Overtemperature L

Driven low

Undervoltage L

Overvoltage L

Typical application schematic VNQ860-E, VNQ860SP-E

8/19 Doc ID 10964 Rev 6

5 Typical application schematic

Figure 5. Typical application schematic

VNQ860-E, VNQ860SP-E Waveforms

Doc ID 10964 Rev 6 9/19

6 Waveforms

Figure 6. Waveforms

PowerSO-10™ thermal data VNQ860-E, VNQ860SP-E

10/19 Doc ID 10964 Rev 6

7 PowerSO-10™ thermal data

Figure 7. PowerSO-10™ PC board

Figure 8. RthJA vs PBC copper area in open box free air condition

VNQ860-E, VNQ860SP-E Reverse polarity protection

Doc ID 10964 Rev 6 11/19

8 Reverse polarity protection

A schematic solution to protect the IC against a reverse polarity condition is proposed.

This schematic is effective with any type of load connected to the outputs of the IC.

The RGND resistor value can be selected according to the following conditions to be met:

1. RGND ≤ 600 mV / (IS in ON state max).

2. RGND ≥ (-VCC) / (-IGND)

where -IGND is the DC reverse ground pin current and can be found in the absolute

maximum rating section of the device datasheet.

The power dissipation associated to RGNG during reverse polarity condition is:

PD = (-VCC)2/RGND

This resistor can be shared by several different ICs. In such case IS value on formula (1) is

the sum of the maximum ON-state currents of the different devices.

Please note that if the microprocessor ground and the device ground are separated then the

voltage drop across the RGND (given by IS in ON state max * RGND) produce a difference

between the generated input level and the IC input signal level. This voltage drop will vary

depending on how many devices are ON in the case of several high side switches sharing

the same RGND.

Figure 9. Reverse polarity protection

Statusi

Inputi

GND

Outputi

+ Vcc

RGND

(Optional)

Load

Statusi

Inputi

GND

Outputi

+ Vcc

RGND

(Optional)

Load

Package mechanical data VNQ860-E, VNQ860SP-E

12/19 Doc ID 10964 Rev 6

9 Package mechanical data

In order to meet environmental requirements, ST offers these devices in different grades of

ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®

specifications, grade definitions and product status are available at: www.st.com.

ECOPACK® is an ST trademark.

Table 11. PowerSO-10™ mechanical data

Dim.

mm inch

Min Typ Max Min Typ Max

A 3.35 3.65 0.132 0.144

A1 0.00 0.10 0.000 0.004

B 0.40 0.60 0.016 0.024

c 0.35 0.55 0.013 0.022

D 9.40 9.60 0.370 0.378

D1 7.40 7.60 0.291 0.300

E 9.30 9.50 0.366 0.374

E1 7.20 7.40 0.283 0.291

E2 7.20 7.60 0.283 0.300

E3 6.10 6.35 0.240 0.250

E4 5.90 6.10 0.232 0.240

e 1.27 0.050

F 1.25 1.35 0.049 0.053

H 13.80 14.40 0.543 0.567

h 0.50 0.002

L 1.20 1.80 0.047 0.071

q 1.70 0.067

a 0° 8°

VNQ860-E, VNQ860SP-E Package mechanical data

Doc ID 10964 Rev 6 13/19

Figure 10. PowerSO-10™ package dimensions

Figure 11. PowerSO-10™ suggested pad and tube shipment (no suffix)

Package mechanical data VNQ860-E, VNQ860SP-E

14/19 Doc ID 10964 Rev 6

Figure 12. Tape and reel shipment (suffix “TR“)

VNQ860-E, VNQ860SP-E Package mechanical data

Doc ID 10964 Rev 6 15/19

Figure 13. SO20 mechanical data and package dimensions

OUTLINE AND

MECHANICAL DATA

DIM.

mm inch

MIN. TYP. MAX. MIN. TYP. MAX.

A 2.35 2.65 0.093 0.104

A1 0.10 0.30 0.004 0.012

B 0.33 0.51 0.013 0.200

C 0.23 0.32 0.009 0.013

(1)

12.60 13.00 0.496 0.512

E 7.40 7.60 0.291 0.299

e 1.27 0.050

H 10.0 10.65 0.394 0.419

h 0.25 0.75 0.010 0.030

L 0.40 1.27 0.016 0.050

k 0˚ (min.), 8˚ (max.)

ddd 0.10 0.004

(1) “D” dimension does not include mold flash, protusions or gate

burrs. Mold flash, protusions or gate burrs shall not exceed

0.15mm per side.

SO20

0016022 D

Package mechanical data VNQ860-E, VNQ860SP-E

16/19 Doc ID 10964 Rev 6

Figure 14. SO20 tube shipment (no suffix)

Figure 15. Tape and reel shipment (suffix “13TR“)

VNQ860-E, VNQ860SP-E Order codes

Doc ID 10964 Rev 6 17/19

10 Order codes

Table 12. Ordering information

Order codes Package Packaging

VNQ860-E SO20 Tu b e

VNQ860SP-E PowerSO-10™

VNQ86013TR-E SO20 Tape and reel

VNQ860SP13TR-E PowerSO-10™

Revision history VNQ860-E, VNQ860SP-E

18/19 Doc ID 10964 Rev 6

11 Revision history

Table 13. Document revision history

Date Revision Changes

14-Jul-2005 1 Updates, new template

7-Nov-2005 2 Few updates

07-Jul-2008 3 Added Section 8 on page 11

28-Apr-2009 4 Updated Figure 13 on page 15

05-May-2010 5 Updated coverpage

01-Sep-2010 6 Updated Table 10 on page 7

VNQ860-E, VNQ860SP-E

Doc ID 10964 Rev 6 19/19

Please Read Carefully:

Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the

right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any

time, without notice.

All ST products are sold pursuant to ST’s terms and conditions of sale.

Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no

liability whatsoever relating to the choice, selection or use of the ST products and services described herein.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this

document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products

or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such

third party products or services or any intellectual property contained therein.

UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED

WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED

WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS

OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.

UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT

RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING

APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,

DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE

GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.

Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void

any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any

liability of ST.

ST and the ST logo are trademarks or registered trademarks of ST in various countries.

Information in this document supersedes and replaces all information previously supplied.

The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.

STMicroelectronics group of companies

Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -

Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America