Rev.01.09.13_78
iMP Series
1 of 9
Embedded Power for
Business-Critical Continuity
Electrical Specifications
Input
Input ra nge: 85 - 264 Vac 120 - 350 Vdc
(limited to 300 Vdc in medical applications)
Frequency: 47 - 440 Hz
Inrush current: 40 A peak max. (soft start)
Efficiency: Up to 85% @ full case load
Power Factor: 0.99 typ. meets EN61000-3-2 (n/a @ 440 Hz)
Turn-on time: AC on 2.0 sec typ., inhibit/enable 150 ms typical
Programmable delay; 50 ms internal turn-on delay (Dual Output only)
EMI filter: CISPR 22/EN55022 Level “B”**
Leakage current: 300 µA max. @ 240 Vac; 47 - 63 Hz
Radiated EMI: CISPR 22/EN55022 Level “B”**
Holdover storage: 20 ms minimum (independent of input Vac) additional 34ms holdover
storage with optional HUP module
(SEMI F47 compatible). For iMP4 15 ms (low-line), 10 ms (high-line)
AC OK: > 5 ms early warning min. before outputs lose regulation
Full cycle ride thru (50 Hz) (n/a on iMP4 > 750 W @ 90 Vac)
Harmonic distortion: Meets EN61000-3-2
Isolation: Meets EN60950 and EN60601
Global Inhibit/Enable: TTL, Logic “1” and Logic “0”; configurable
Input fuse (internal): iMP4: 16 A; iMP8: 20 A; iMP1: 25 A (both lines fused)
Warranty: 2 years
Intelligent MP
Series
Up to 1500 Watts
Special Features
• Full Medical EN60601 approval
• IntelligentI2C control
• Voltageadjustmentonalloutputs
(Manual or I2C)
• Configurableinputandoutput
(case and module) OK signals and
indicators
• Configurableinhibit/enable
• Configurableoutput
UP/DOWN sequencing
• Configurablecurrentlimit
(foldback or constant current)
• Highpowerdensity(8.8W/cu-in)
• Intelligentfan
(speed control/fault status)
• DownloadableGUIfromwebsite
• Customerprovidedairoption
• uPcontrolledPFCinputwithactive
inrush protection
• I2C monitor of voltage, current, and
temp
• Programmablevoltage,currentlimit,
inhibit/enable through I2C
• Optionalextendedhold-upmodule
(SEMI F47 compliance)
• Increasedpowerdensityto50%over
standard MP
• Externalswitchingfrequencysync
input
• Optionalconformalcoating
• Industrialtemprange(-40ºC to 70 ºC)
• Nopreloadrequired
• Industrialshock/vibration(>50G’s)
Total Power: Up to 1500 Watts
Input Voltage: 85 - 264 Vac
120-300 Vdc
# of Outputs: Up to 21
Safety
• UL UL60950/UL2601**
• CSA CSA22.2 No. 234 Level 5
• VDE EN60950/EN60601-1**
• BABT Compliance to
EN60950/EN60601 BS7002
• CB Certificate and report
• CE Mark to LVD
Rev.01.09.13_78
iMP Series
2 of 9
Embedded Power for
Business-Critical Continuity
Output Module Line-up
Operating temperature: -40 ° to 70 °C ambient. Derate each output 2.5% per degree from 50 °C to 70 °C. ( -20 °C start up)
Storage temperature: -40 °C to 85 °C
Electromagnetic susceptibility: Designed to meet EN61000-4; -2, -3, -4, -5, -6, -8, -11 Level 3
Humidity: Operating; non-condensing 10% to 95% RH
Vibration: IEC68-2-6 to the levels of IEC721-3-2
MTBF demonstrated > 550,000 hours at full load, 220 Vac and 25 °C ambient conditions
Environmental Specifications
Output
Adjustment range:* ± 10% minimum all outputs (manual)
(fullmoduleadjustmentrangeusingI2C)
Factory set point accuracy: ± 1%
I2C output program
accuracy:
± 5%
Margining: ± 4 - 6% nominal analog
(single output module only)
Overall regulation: 0.4% or 20 mV max. (1500W modules 1% max.)
(36 W modules 4% maximum)
Ripple: RMS: 0.1% or 10mV, whichever is greater
Pk-Pk: 1.0% or 50mV, whichever is greater
Bandwidth limited to 20 MHz
Dynamic response: < 2% or 100 mV, with 25% load step
Recovery time: To within 1% in < 300 µsec
Overcurrent
protection:**
Configurable through I2C (calibration required).
Single output module and main output of the
dual output module 105 - 120% of rated output
current. Aux output of dual output module 105
- 140% of rated output current
Short-circuit protection: Protected for continuous short-circuit
Recovery is automatic upon removal of short
Overvoltage protection:* Configurable through I2C
Single output module: 2 - 5.5 V 122 - 134% ; 6 - 60 V 110 - 120%
Dual output module: 2 - 6 V 122 - 134% ; 8 - 28 V 110 - 120%
Triple output module: 110 - 120% of highest voltage rating
Output Continued
Reverse voltage protection: 100% of rated output current
Thermal protection:*
(OTP and OTW)
Configurable through I2C
All outputs disabled when internal temp
exceeds safe operating range. > 5 ms warning
(AC OK signal) before shutdown
Remote sense: Up to 0.5 V total drop (not available on triple
output module)
Single wire parallel: Current share to within 2% of total rated
current
DC OK:* ± 5% of nominal. Configurable through I2C
Minimum load: Not required
Housekeeping standby: 5 Vdc @ 1.0 A max. present whenever AC input
is applied (Optional 2.0 A available)
Module inhibit:* Configured and controlled through I2C
Switching frequency: 250k Hz accepts external sync signal
Output/Output isolation: >1 Megohm, 500 V
External sync: TTLclockinputsignalusedtoadjustswitching
frequency. Frequency 500 kHz ± 20%; Duty
cycle 40 - 55%
* Can be controlled via I2C
** Controlled via I2C but requires load calibration
Module Code 1 2 3 5 4—
Module Type Single Single Single Single Dual Triple
Max output power 210 W 360 W 750 W 1500 W 144 W 36 W
Max output current 35 A 60 A 150 A 140 A 10 A 2 A
Output voltages available* 2-60 V 2-60 V 2-60 V 6-60 V
8 - 15*, 24 - 28; 8 - 15*, 8 - 15*; 8 - 15*,
2 - 6; 2 - 6, 2 - 6; 24 - 28, 24 - 28;
24 - 28, 2 - 6
8-15, 8-15, 2-6; 8-15, 8-15, 8-15;
8-15, 8-15, 18-28; 8-15, 18-28, 2-6
Standard voltage increments 25 25 25 18 16 18
Remote sense Yes Yes Yes Yes Yes Yes No
Remote margin Yes Yes Yes Yes No No No
V-Program - I2C Control Yes Yes Yes Yes Yes Yes No
Active Current Share Yes Yes Yes Yes Yes No No
Module Inhibit - I2C Control Yes Yes Yes Yes Yes Yes Yes
Module Inhibit - Analog Yes Yes Yes Yes Yes No No
Overvoltage/Overcurrent
protection Yes Yes Yes Yes Yes Yes Yes
Minimum load required No No No No No No No
Slots occupied in any iVS case 1 2 3 4 1 1
* Note: Contact Factory for extended range down to 6 V
Rev.01.09.13_78
iMP Series
3 of 9
Embedded Power for
Business-Critical Continuity
7 6 5 4 3 2 1
iMP4
available slots
iMP8
available slots
Slot 1
Slot 2
Slot 3
Slot 4
Slot 5
Slot 1
Slot 2
Slot 3
Slot 4
Slot 5
Slot 6
Slot 1
Slot 2
Slot 3
Slot 4
Slot 6
Slot 7
Slot 5
iMP1
available slots
Parallel Codes
0 = no parallel
1 = 1 & 2
2 = 2 & 3
3 = 3 & 4
4 = 4 & 5
5 = 3 & 4 & 5
6 = 5 & 6
7 = 4 & 5 & 6
8 = 6 & 7
9 = 3 & 4, 6 & 7
A = 1 & 2, 3 & 4, 5 & 6
C = 2 & 3, 4 & 5
E = 3 & 4, 5 & 6
F = 2 & 3, 4 & 5, 6 & 7
Output Module Voltage/Current
Ordering Note:
1. The cases and modules of both MP and iMP
series can be interchanged to allow more
flexibility. If intelligent modules are used
with non-intelligent cases, a numeric code
“4” is placed at the end of the module code
(ex. 4LL0 becomes 4LL4).
2. USB to I2C module order code 73-769-001
iMP1* - 3L0 - 2E2 - 1Q1 - 4LL0 - 00 - A - ###
Case Size (mm)
4 = 2.5” x 5” x 10”; 750 W-1158 W, 5 Slots
(63.5 x 127 x 254)
8 = 2.5” x 7” x 10”; 1000 W-1200 W, 6 Slots
(63.5 x 177.8 x 254)
1 = 2.5” x 8” x 11”; 1200 W-1500 W, 7 Slots
(63.5 x 203.2 x 279.4)
*Note: Add “E” after iMP4 to denote IEC
input option. e.g. iMP4E
(Not available on iMP8 or iMP1)
Module Codes
Module/voltage/option codes
Module codes:
(None) = 36 W triple O/P (1 slot)
1 = 210 W single O/P (1 slot)
2 = 360 W single O/P (2 slot)
3 = 750 W single O/P (3 slot)
4 = 144 W dual O/P (1 slot)
5 = 1500 W single O/P (4 slot)
6 - 9 = future
Case Option Codes
First digit
0 - 9, A-Z parallel code
(See Parallel Codes table above)
Second digit
0 = No options
1 = Reverse air
3 = Global enable
4 = Fan idle with inhibit
5 = Opt 1 + Opt 3
6 = Opt 1 + Opt 4
7 = Opt 3 + Opt 4
8 = Opt 1 +3 +4
9 = CAN BUS/RS485 73-544-002
C = Opt 3 + Opt 9
Software Code
Voltage Codes:
See Output Module Voltage/Current
table above
Option Codes:
0 = Standard
1 = Module enable
2 = Constant current
3 = 1 & 2 combined
4 = Set for use in standard
(non-intelligent case)
5 = Shutdown mode for 1500W
6 = 1 & 5 combined
7 - 9 = future
Module/Voltage/Option Codes
First - Module Code
Second - Voltage Code
Third - Option Code Case Option Codes
Software code
used for configura-
tion change. “A” is
standard
Case Size
Factory assembled
for hardware of
firmware mods.
Hardware Code
Ordering Information
Voltage Voltage
Code Single Output Module Code Dual Output*** Triple Output I2C
Adjustment
Ranges****
1 2 3 5+4 4 - - -
2 V A35 A 60 A 150 A —10 A 10 A — — 2 A 1.8 - 2.2
2.2 V B35 A 60 A 150 A —10 A 10 A — — 2 A 2.0 - 2.4
3 V C35 A 60 A 150 A —10 A 10 A — — 2 A 2.7 - 3.3
3.3 V D35 A 60 A 150 A —10 A 10 A — — 2 A 3.0 - 3.6
5 V E35 A 60 A 150 A —10 A 10 A — — 2 A 4.5 - 5.5
5.2 V F35 A 60 A 144 A —10 A 10 A — — 2 A 4.7 - 5.7
5.5 V G34 A 58 A 136 A —10 A 10 A — — 2 A 5.0 - 6.1
6.0 V H23 A 42 A 97.5 A 140 A 10 A* 10 A* — — 2 A 5.4 - 6.6
8.0 V I20 A 36 A 84.4 A 140 A 10 A 4 A 1 A 1 A 1 A 7.2 - 8.8
10 V J18 A 32 A 75 A 140 A 10 A 4 A 1 A 1 A 1 A 9.0 - 11.0
11 V K17 A 31 A 68 A 136.3 A 10 A 4 A 1 A 1 A 1 A 9.9 - 12.1
12 V L17 A 30 A 62.5 A 125 A 10 A 4 A 1 A 1 A 1 A 10.8 - 13.2
14 V M14 A 21 A 53.5 A 107 A 9 A 4 A 1 A 1 A 1 A 12.6 - 15.4
15 V N14 A 20 A 50 A 100 A 8 A 4 A 1 A 1 A 1 A 13.5 - 16.5
18 V O11 A 19 A 41.6 A 83.3 A — — — 0.5 A 0.5 A 16.2 - 19.8
20 V P10.5 A 18 A 37.5 A 75 A — — — 0.5 A 0.5 A 18.0 - 22.0
24 V Q8.5 A 15 A 30 A 62.5 A 4 A 2 A —0.5 A 0.5 A 21.6 - 26.4
28 V R6.7 A 11 A 26.8 A 53.5 A 3 A 2 A —0.5 A 0.5 A 25.2 - 30.8
30 V S6.5 A 11 A 25 A 50 A — — — — — 27.0 - 33.0
33 V T6.2 A 10.9 A 22.7 A 35.8 A — — — — — 29.7 - 36.3
36 V U5.8 A 10 A 20.8 A 35.8 A — — — — — 32.4 - 39.6
42 V V4.2 A 7.5 A 16 A 35.7 A — — — — — 37.8 - 46.2
48 V W4.0 A 7.5 A 15.6 A 31.2 A — — — — — 43.2 - 52.8
54 V X3.7 A 6.0 A 13.9 A 27.7 A — — — — — 48.6 - 59.4
60 V Y3.5 A 6.0 A 12.5 A 25 A — — — — — 54.0 - 66.0
Non-std** ZSpecial Voltage - Consult Factory for specifications
*Note: Contact Factory for extended range down to 6 V.
**Increments of current not shown can be achieved by paralleling modules
(add currents of each module selected).
***Total output power on dual module must not exceed 144 W.
**** For single output modules only.
+ Applicable for iMP1 only.
Rev.01.09.13_78
iMP Series
4 of 9
Embedded Power for
Business-Critical Continuity
Input
85-264 Vac 180-264 Vac
iMP8 = 2.5” x 7” x 10” 6 available slots 1000 W max. 1200 W max.
(63.5 x 177.8 x 254mm)
iMP1 = 2.5” x 8” x 11” 7 available slots 1200 W max. 1500 W max.
(63.5 x 203.2 x 279.4mm)
iMP4 (AC input on opposite side)
iMP8 and iMP1
iMP1 only
Single
AC input
AC Input
Pin No. Function
1AC neutral
2AC line (hot)
3Chassis (earth) ground
PFC Input Connector (control and signals)
Pin No. Function
1Input AC OK - “emitter”
2Input AC OK - “collector”
3Global DC OK - “emitter”
4Global DC OK - “collector”
5External Sync
6Global inhibit/optional enable logic “0”
7Global inhibit/optional enable logic “1”
8Global inhibit/optional enable return
9+5 VSB housekeeping
10 +5 VSB housekeeping return
I2C Bus Output Connector
Pin No. Function
1No connection
2No connection
3No connection
4Serial clock signal (SCL)
5Serial data signal (SDA)
6Address bit 0 (A0)
7Address bit 1 (A1)
8Address bit 2 (A2)
9Secondary return (GND)
10 5 Vcc external bus (5 VCC. Bus)
Mates with
Molex 90142-0010 Housing
90119-2110 Pin
Connector Kit Part No.:
70-841-004
Mates with
Landwin 2050S1000 Housing
2053T011V Pin
or
JST PHDR-10VS Housing
JST SPHD-002T-P0.5 (28-24)
JST SPHD-001T-P0.5 (26-22)
Connector Kit Part No.:
70-841-023
Figure 1. AC Input
Figure 2. Connector J1
Figure 3. Connector J2
Input
90-264 Vac 180-264 Vac
iMP4 = 2.5” x 5” x 10” 5 available slots 750 W max. 1158 W max.
(63.5 x 127 x 254)
210 W
360 W
750 W
144 W
Pin Connectors
Triple
Dual
36 W
1500 W
Rev.01.09.13_78
iMP Series
5 of 9
Embedded Power for
Business-Critical Continuity
DC-DC Converter Output Modules
Control Signal Information, J1 Control Connector
Pin No. Function
1 + Remote Sense single or dual o/p main
2 Remote Margin / V. Program single o/p
3 Margin High single o/p
4 - Remote Sense / Margin Low single or dual o/p main
5 Spare
6 Module, Isolated Inhibit single or dual o/p
7 Module Inhibit return single or dual o/p
8 Current Share (SWP) single or dual o/p main
9 + Remote Sense V2 dual o/p, single is spare
10 - Remote Sense V2 dual o/p, single is spare
*Note: All iMP modules have a green DCOK LED.
(except for 36 W module)
.63”
(16.0)
.32”
(8.1)
1.38” (35.2)
(2X)
.44”
(11.4)
.48” (12.1)
(2X)
.33”
(8.5)
V ADJ
V-
V+
M 4 X 8 SCREWS WITH
CONICAL WASHER
DC OUTPUT CONNECTOR
PIN 1
.44"
(11.4)
.32"
(8.1)
1.38"
(35.1)
.48"
(12.1)
.44” (11.2)
2X
V+
M4X8 SCREWS WITH CONICAL WASHER
DC OUTPUT CONNECTOR
PIN 1
V-
V ADJ
PIN 1
V2 ADJ
.32
(8.1)
.42 (10.7)
V1 +
V1 -
V2 +
M3X8 SCREWS WITH SPRING WASHER
(4X)
.46 (11.7)
(4X)
.30 (7.5)(3X)
V1 ADJ
1.17 (29.7)
V2 -
Single 210 Watt
Dual 144 Watt
Single 360 Watt Single 750 Watt
iMP Modules
Triple 36 Watt
V1 ADJ
V2 ADJ
V3 ADJ
V1+
V3+
V1-
V2+
V2-
V3-
.32"
(8.1)
.44"
(11.0)
1.24"(31.5)
(2X)
.61"(15.6)
(2X)
.59"
(15.0)
.63"
(16.0)
V+
V-
M4X8 SCREWS
(4X)
V ADJ
PIN 1
DC OUTPUT
CONNECTOR
Mates with
Molex 90142-0010 Housing
90119-2110 Pin
Figure 4. Connector J1
Mates with
Molex 09-91-0600 Housing
26-60-5060 Pin
Single 1500 Watt
Rev.01.09.13_78
iMP Series
6 of 9
Embedded Power for
Business-Critical Continuity
Notes
1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). Max torque: 6 in-lbs. (0.67 N-m). (Optional IEC input connector)
2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series).
Connector kit includes mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000
(Landwin) with 2053T011P (Landwin) pins or JST PHDR-IOVS Housing and JST SPHD-002T-PO.5 pins.
3. Chassis material: aluminum with chemical film coating (conductive).
4. All dimensions are in millimeters and inches, and are typical.
5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.150” (3.8 mm). Max. torque: 5 in-lbs. (0.57 N-m).
6. Output module connections: All single O/P modules are M4 x 8mm screws. Max. torque: 10 in-lbs. (1.13 N-m).
Dual O/P module is M3 x 8mm screws. Max. torque: 5 in-lbs. (0.57 N-m).
iMP Series
iMP4 (750/1158 Watts Max)
5-Inch Case Size: iMP4: 2.5” x 5” x 10” (63.5mm x 127mm x 254mm)
Weight: iMP4Case:3lbs.•360WSingle1.0lb.
•750WSingle:1.6lbs.144WDual:0.6lb.
Rev.01.09.13_78
iMP Series
7 of 9
Embedded Power for
Business-Critical Continuity
iMP Series
iMP8 (1000/1200 Watts Max)
7-Inch Case Size: iMP8: 2.5” x 7” x 10” (63.5mm x 177.8mm x 254mm)
Weight: iMP8Case:4.1lbs.•210WSingle:0.6lb.•360WSingle:1.0lb.
•750WSingle:1.6lbs.144WDual:0.6lb.
Notes
1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). Max torque: 6 in-lbs. (0.67 N-m).
2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series)
Connector kit includes mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000
(Landwin) with 2053T011P (Landwin) pins or JST PHDR-IOVS Housing and JST SPHD-002T-PO.5 pins.
3. Chassis material: aluminum with chemical film coating (conductive).
4. All dimensions are in millimeters and inches, and are typical.
5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.150” (3.8 mm). Max. torque: 5 in-lbs. (0.57 N-m).
6. Output module connections: All single O/P modules are M4 x 8mm screws. Max. torque: 10 in-lbs. (1.13 N-m).
Dual O/P module is M3 x 8mm screws. Max. torque: 5 in-lbs. (0.57 N-m).
Rev.01.09.13_78
iMP Series
8 of 9
Embedded Power for
Business-Critical Continuity
8-Inch Case Size: iMP1: 2.5” x 8” x 11” (63.5mm x 203.2mm x 279.4mm)
Weight: iMP1Case:5.0lb.•210WSingle:0.6lb.
•360WSingle:1.0lb.•750WSingle:1.6lb.
•144WDual:0.6lb.
Notes
1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). Max torque: 6 in-lbs (0.67 N-m).
2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series).
Connector kit includes mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000 (Landwin) with
2053T011P (Landwin) pins or JST PHDR-IOVS Housing and JST SPHD-002T-PO.5 pins.
3. Chassis material: aluminum with chemical film coating (conductive).
4. All dimensions are in millimeters and inches, and are typical.
5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.150” (3.8 mm). Max. torque: 5 in-lbs. (0.57 N-m).
6. Output module connections: All single O/P modules are M4 x 8mm screws. Max. torque: 10 in-lbs. (1.13 N-m).
Dual O/P module is M3 x 8mm screws. Max. torque: 5 in-lbs. (0.57 N-m).
iMP Series
iMP1 (1200/1500 Watts Max)
Rev.01.09.13_78
iMP Series
9 of 9
Embedded Power for
Business-Critical Continuity
Americas
5810 Van Allen Way
Carlsbad, CA 92008
USA
Telephone: +1 760 930 4600
Facsimile: +1 760 930 0698
Europe (UK)
Waterfront Business Park
Merry Hill, Dudley
West Midlands, DY5 1LX
United Kingdom
Telephone: +44 (0) 1384 842 211
Facsimile: +44 (0) 1384 843 355
Asia (HK)
14/F, Lu Plaza
2 Wing Yip Street
Kwun Tong, Kowloon
Hong Kong
Telephone: +852 2176 3333
Facsimile: +852 2176 3888
For global contact, visit:
www.Emerson.com/EmbeddedPower
techsupport.embeddedpower
@emerson.com
While every precaution has been taken to ensure
accuracy and completeness in this literature, Emerson
Network Power assumes no responsibility, and disclaims
all liability for damages resulting from use of this
information or for any errors or omissions.
Emerson and the Emerson Network Power
logo are trademarks of Emerson Electric Co.
©2012 Emerson Electric Co.
All rights reserved.
EmersonNetworkPower.com
Embedded Computing
Embedded Power
Monitoring
Outside Plant
Power Switching & Controls
Precision Cooling
Racks & Integrated Cabinets
Services
Surge Protection
Emerson Network Power.
The global leader in enabling
business-critical continuity.
AC Power
Connectivity
DC Power
Optional CANBUS or RS485 Interface
The RS485/CAN-to-I2C uses 2 Input Protocols and 1 Output Protocol.
The Input Protocols used are RS485 using Modbus (Command Index: 0x01), and CAN using modified
Modus (Command Index: 0x02).
The Output Protocol use is: I2C with SMBus support (Command Index: 0x80).
RS485/CAN - to - I2C
For Detailed Info, Download the Software Requirements Specification (SRS) from
www.PowerConversion.com/imp
iMP CAN RS485
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Emerson Network Power:
73-769-001 IMP1-3Q0-3W0-00-A