Product Specification - Sep 19, 2003 V.6 Supersedes Date of Jul. 07, 2003 DATA SHEET CHIP RESISTORS RC0603 5%; 1% 2 Chip Resistor Surface Mount RC 7 0603 SERIES SCOPE This specification describes RC 0603 series chip resistors made by thick film process. ORDERING INFORMATION Part number is identified by the series, size, tolerance, packing style, temperature coefficient, special type and resistance value. RC0603 X X X XX XXXX (1) (2) (3) (4) (5) MARKING RC0603 (1) TOLERANCE F = 1% J = 5% E-24 series: 3 digits First two digits for significant figure and 3rd digit for number of zeros ynsc001 Fig. 1 Value=10K (2) PACKAGING TYPE R = Paper taping reel C = Bulk case (3) TEMPERATURE CHARACTERISTIC OF RESISTANCE 10C E-96 series: 3 digits for 06031% EIA-96 marking method ynsc002 Fig. 2 Value=12.4 K For 06031% E-24 series, one short bar under marking letter ynsc003 F = 100ppm/C G = 200ppm/C I = 300ppm/C - = Base on spec (4) SPECIAL TYPE 07 = 7 inch dia. Reel 10 = 10 inch dia. Reel 13 = 13 inch dia. Reel (5) RESISTANCE VALUE: 5R6, 56R, 560R, 5K6, 56K, 22M. Fig. 3 E-24 1% Value=56K EIA - 96 MARKING RULE Table 1 Code Value Code Value Code Value Code Value Code Value Code Value Code Value Code Value 01 100 13 133 25 178 37 237 49 316 61 422 73 562 85 750 02 102 14 137 26 182 38 243 50 324 62 432 74 576 86 768 03 105 15 140 27 187 39 249 51 332 63 442 75 590 87 787 04 107 16 143 28 191 40 255 52 340 64 453 76 604 88 806 05 110 17 147 29 196 41 261 53 348 55 464 77 619 89 825 06 113 18 150 30 200 42 267 54 357 66 475 78 634 90 845 07 115 19 154 31 205 43 274 55 365 67 487 79 649 91 866 08 118 20 158 32 210 44 280 56 374 68 499 80 665 92 887 09 121 21 162 33 215 45 287 57 383 69 511 81 681 93 909 10 124 22 165 34 221 46 294 58 392 70 523 82 698 94 931 11 127 23 169 35 226 47 301 59 402 71 536 83 715 95 953 12 130 24 174 36 232 48 309 60 412 72 549 84 732 96 976 Table 1. shows the first two digits of the three-digit EIA-96 part-marking scheme. The third character is a letter multiplier: X=10 -1 , Y=10 -2 , A=10 0, B=10 1, C=10 2, D=10 3, E=10 4, F=10 5 www.yageo.com Sep. 19, 2003 V.6 3 Chip Resistor Surface Mount RC SERIES 7 0603 CONSTRUCTION The resistors are constructed out of protective coat a high-grade ceramic body. Internal resistor layer metal electrodes are added at each inner electrode H end and connected by a resistive end termination paste. The composition of the paste ceramic substrate I2 is adjusted to give the approximate Fig. 4 Chip resistor construction required resistance and laser cutting of this resistive layer that achieves tolerance trims the value. The resistive layer is covered with a protective coat and printed with the resistance value. Finally, the two external terminations are added. See fig. 4. columns MBE940_a DIMENSIONS Table 2 TYPE RC0603 L (mm) 1.600.1 W (mm) 0.800.10 H (mm) 0.450.10 I1 (mm) 0.250.15 I2 (mm) 0.250.15 POWER RATING RATED POWER AT 70C, RC0603 1/10W MRA632 mns Pmax (%Prated ) 100 50 For dimension see Table 2 protective coat I1 W MBE940_a Fig. 5 Chip resistor dimension L ELECTRICAL CHARACTERISTICS Table 3 CHARACTERISTICS RC0603 1/10 W Operating Temperature Range -55C to +155C Maximum Working Voltage 50V Maximum Overload Voltage 100V Dielectric Withstanding Voltage 100V 0 55 0 50 70 100 o Tamb ( C) 155 Fig. 6 Maximum dissipation (Pmax) in percentage of rated power as a function of the operating ambient temperature (Tamb) RATED VOLTAGE: The DC or AC (rms) continuous working voltage corresponding to the rated power is determined by the following formula: 1 to 22M (E24) Resistance Range 1 to 10M (E96) Zero Ohm Jumper<0.05 Temperature Coefficient Jumper Criteria 10<R 10M 100ppm/C R10; R>10M 200ppm/C Rated Current 1.0A Maximum Current 2.0A V=(P X R) Where V=Continuous rated DC or AC (rms) working voltage (V) P=Rated power (W) R=Resistance value (X) www.yageo.com Sep. 19, 2003 V.6 4 Chip Resistor Surface Mount RC SERIES 7 0603 TAPING REEL Table 4 DIMENSION For dimension see Table 4 RC0603 Tape Width T 8mm OA (mm) 180+0/-3 OB (mm) 60+1/-0 OC (mm) 13.00.2 W (mm) 9.00.3 T (mm) 11.41 21 0.8 Fig. 7 Reel dimension C W B A MSA284_a PAPER TAPE SPECIFICATION Table 5 DIMENSION P0 RC0603 A (mm) B (mm) W (mm) E (mm) F (mm) P0 (mm) P1 (mm) P2 (mm) OD0 (mm) T (mm) T P2 D0 1.10.1 E 1.900.1 8.00.2 F cover tape 1.750.1 W B 3.50.05 4.00.1 4.00.05 A MBD123_a P1 2.00.05 1.5+0.1/-0 Fig. 8 Paper tape dimension For dimension see Table 5 0.700.10 PACKING METHODS LEADER/TRAILER TAPE SPECIFICATION BULK CASSETTE handbook, 4 columns leader end empty compartments with cover tape (min. 240 mm) trailer end slider shutter coupled portion cover tape only leader 400 mm trailer (max. 260 mm) MGB377 CCB325 Fig. 9 Leader and trailer tape dimension Fig.10 Bulk case outline Table 6 Packing style and packaging quantity PACKING STYLE Paper Taping Reel (R) Bulk Cassette (C) REEL DIMENSION RC0603 7" (178 mm) 5,000 10" (254 mm) 10,000 13" (330 mm) 20,000 - 25,000 www.yageo.com Sep. 19, 2003 V.6 5 Chip Resistor Surface Mount TYPE RC SERIES 7 0603 TEST METHOD Temperature Coefficient of Resistance (T.C.R.) Measure resistance at +25C or specified room temperature as R1, then measure at -55C or +155C respectively as R2 Determine the temperature coefficient of resistance from the following formula: Thermal Shock ACCEPTANCE STANDARD Formula Refer to table 3 R2-R1 T.C.R.= ------------------------- x106 (ppm/C) R1(t2-t1) Where t1=+25C or specified room temperature t2=-55C or +155C test temperature R1=resistance at reference temperature in ohms R2=resistance at test temperature in ohms At -553C for 2 minutes and at +1552C for 2 minutes as one cycle. After 5 cycles, the specimen shall be stabilized at room temp. (0.5%+0.05) Measure the resistance to determine R/R(%) after one more hour. Low Temperature Operation Place the specimen in a test chamber maintained at -65 (+0/-5)C. After one hour stabilization at this temperature, full rated working voltage shall be applied for 45 (+5/-0) minutes. Have15 (+5/-0 ) minutes after remove the voltage, the specimen shall be removed from the chamber and stabilized at room temperature for 24 hrs. (0.5%+0.05) for 1% tol . (1.0%+0.05) for 5% tol. No visible damage Measure the resistance to determine R/R(%). Short Time Overload Apply 2.5 times of rated voltage but not exceeding the maximum overload voltage for 5 seconds. Have the specimen stabilized at room temperature for 30 minutes minimum. (1.0%+0.05) No visible damage Measure the resistance to determine R/R(%). Insulation Resistance Place the specimen in the jig and apply a rated continues overload voltage (R.C.O.V) for one minute as shown. Type Voltage (DC) RC0603 10,000M 100V Measure the insulation resistance. Dielectric Withstand Voltage Resistance To Soldering Heat Place the specimen in the jig and apply a specified value continuous overload voltage as shown for one minute. Type RC0603 Voltage (AC) 100Vrms Immerse the specimen in the solder pot at 2605C. for 101 seconds. Have the specimen stabilized at room temperature for 30 minutes minimum. Breakdown voltage> specification and without open/short (0.5%+0.05) No visible damage Measure the resistance to determine R/R(%). www.yageo.com Sep. 19, 2003 V.6 6 Chip Resistor Surface Mount TYPE Moisture Resistance RC SERIES 7 0603 TEST METHOD ACCEPTANCE STANDARD Place the specimen in the test chamber and subject to 42 damp heat cycles. Each one of which consists of the steps 1 to 7 as figure 12. The total length of test is 1,000 hours. Have the specimen stabilized at room temperature for 24 hours after testing. (0.5%+0.05) for 1% tol. (1.5%+0.05) for 5% tol. No visible damage Measure the resistance to determine R/R(%). Life Place the specimen in the oven at 702C. Apply the rated voltage to the specimen at the 1.5 hours on and 0.5 hour off cycle. The total length of test is 1,000 hours. Have the specimen stabilized at room temperature for one hour minimum after testing. (1%+0.05) for 1% tol. (1.5%+0.05) for 5% tol. No visible damage Measure the R/R(%). Solderability Bending Strength Immerse the specimen in the solder pot at 2355C for 5 sec. Mount the specimen on a test board as shown in the figure 11. Slowly apply the force till the board is bent for 51 sec. Type Bent Distance (d) At least 95% solder coverage on the termination RC0603 5mm (1.0%+0.05) for 1% tol. (1.0%+0.05) for 5% tol. No visible damage Measure the R/R(%) at this position. Fig. 11 Principle of the bending test www.yageo.com Sep. 19, 2003 V.6 7 Chip Resistor Surface Mount 75 RC 80 - 98% RH 90 - 98% RH temperature [C] SERIES 7 0603 90 - 98% RH 80 - 98% RH 90 - 98% RH initial drying 24 hours rate of change of temperature is unspecified, however, specimens shall not be subjected to radiant heating from chamber conditioning processes 50 end of final cycle; measurements as specified in 2.7 +10 C (+18 F) -2 C (-3.6 F) 25 initial measurements as specified in 2.2 0 temperature tolerance 2 C (3.6 F) unless otherwise specified voltage applied as specified in 2.4 STEP1 STEP2 prior to first cycle only HBK073 optional sub-cycle if specified (2.3); sub-cycle performed during any 5 of the first 9 cycles; humidity uncontrolled during sub-cycle circulation of conditioning air shall be at a minimum cubic rate per minute equivalent to 10 times the volume of the chamber STEP3 STEP4 STEP5 STEP6 STEP7 one cycle 24 hours; repeat as specified in 2.5 0 5 10 15 20 25 time [h] Fig. 12 Conditions by change of temperature www.yageo.com Sep. 19, 2003 V.6