INTEGRATED CIRCUITS 74LVT162374 3.3V LVT 16-bit edge-triggered D-type flip-flop with 30 termination resistors (3-State) Product specification IC23 Data Handbook 1999 Sep 23 Philips Semiconductors Product specification 3.3V 16-bit edge-triggered D-type flip-flop with 30 termination resistors (3-State) FEATURES 74LVT162374 DESCRIPTION * 16-bit edge-triggered flip-flop * 3-State buffers * Output capability: +12 mA / -12 mA * TTL input and output switching levels * Input and output interface capability to systems at 5 V supply * Bus-hold data inputs eliminate the need for external pull-up The 74LVT162374 is a high-performance BiCMOS product designed for VCC operation at 3.3 V. The 74LVT162374 is designed with 30 series resistance in both the High and Low states of the output. This design reduces line noise in applications such as memory address drivers, clock drivers, and bus receivers/transmitters. This device is a 16-bit edge-triggered D-type flip-flop featuring non-inverting 3-State outputs. The device can be used as two 8-bit flip-flops or one 16-bit flip-flop. On the positive transition of the clock (CP), the Q outputs of the flip-flop take on the logic levels set up at the D inputs. resistors to hold unused inputs * Live insertion/extraction permitted * Outputs include series resistance of 30 making external resistors unnecessary * Power-up reset * Power-up 3-State * No bus current loading when output is tied to 5 V bus * Latch-up protection exceeds 500mA per JEDEC Std 17 * ESD protection exceeds 2000 V per MIL STD 883 Method 3015 and 200 V per Machine Model QUICK REFERENCE DATA SYMBOL CONDITIONS Tamb = 25C PARAMETER TYPICAL UNIT 2.9 ns tPLH tPHL Propagation delay nCP to nQx CL = 50pF; VCC = 3.3V CIN Input capacitance VI = 0V or 3.0V 3 pF COUT Output pin capacitance Outputs disabled; VO = 0V or 3.0V 9 pF ICCZ Total supply current Outputs disabled; VCC = 3.6V 70 A ORDERING INFORMATION PACKAGES TEMPERATURE RANGE ORDERING CODE DWG NUMBER 48-Pin Plastic SSOP Type III -40C to +85C 74LVT162374 DL SOT370-1 48-Pin Plastic TSSOP Type II -40C to +85C 74LVT162374 DGG SOT362-1 1999 Sep 23 2 853-2173 22407 Philips Semiconductors Product specification 3.3V 16-bit edge-triggered D-type flip-flop with 30 termination resistors (3-State) LOGIC SYMBOL 47 74LVT162374 PIN CONFIGURATION 46 44 43 41 40 38 37 1D0 1D1 1D2 1D3 1D4 1D5 1D6 1D7 1OE 1 48 1CP 1Q0 2 47 1D0 !Q1 3 46 1D1 48 1CP GND 4 45 GND 1 1OE 1Q2 5 44 1D2 1Q3 6 43 1D3 VCC 7 42 VCC 1Q4 8 41 1D4 1Q0 1Q1 1Q2 1Q3 1Q4 1Q5 1Q6 1Q7 2 3 5 6 8 9 11 12 36 35 33 32 30 29 27 26 2D0 2D21 2D2 2D3 2D4 2D5 2D6 2D7 25 2CP 24 2OE 2Q0 2Q1 2Q2 2Q3 2Q4 2Q5 2Q6 2Q7 13 14 16 17 19 20 22 23 SW00018 LOGIC SYMBOL (IEEE/IEC) 1OE 1CP 2OE 2CP 1D1 1D2 1D3 1D4 1D5 1D6 1D7 1D8 2D1 2D2 2D3 2D4 2D5 2D6 2D7 2D8 1 48 24 25 47 9 40 1D5 10 39 GND 1Q6 11 38 1D6 1Q7 12 37 1D7 2Q0 13 36 2D0 2Q1 14 35 2D1 GND 15 34 GND 2Q2 16 33 2D2 2Q3 17 32 2D3 VCC 18 31 VCC 2Q4 19 30 2D4 2Q5 20 29 2D5 GND 21 28 GND 2Q6 22 27 2D6 2Q7 23 26 2D7 2OE 24 25 2CP 1EN C1 2EN SW00017 C2 1D 1 2 46 3 44 5 43 6 41 8 40 9 38 11 37 12 36 13 2D 2 35 14 33 16 32 17 30 19 29 20 27 22 26 23 1Q1 PIN DESCRIPTION 1Q2 1Q3 1Q4 1Q5 1Q6 PIN NUMBER SYMBOL FUNCTION 47, 46, 44, 43, 41, 40, 38, 37 36, 35, 33, 32, 30, 29, 27, 26 1D0 - 1D7 2D0 - 2D7 Data inputs 2, 3, 5, 6, 8, 9, 11, 12 13, 14, 16, 17, 19, 20, 22, 23 1Q0 - 1Q7 2Q0 - 2Q7 Data outputs 1, 24 1OE, 2OE Output enable inputs (active-Low) 48, 25 1CP, 2CP Clock pulse inputs (active rising edge) 4, 10, 15, 21, 28, 34, 39, 45 GND Ground (0V) 7, 18, 31, 42 VCC Positive supply voltage 1Q7 1Q8 2Q1 2Q2 2Q3 2Q4 2Q5 2Q6 2Q7 2Q8 SW00016 1999 Sep 23 1Q5 GND 3 Philips Semiconductors Product specification 3.3V 16-bit edge-triggered D-type flip-flop with 30 termination resistors (3-State) 74LVT162374 LOGIC DIAGRAM nD1 nD0 nD2 nD3 nD4 nD5 nD6 nD7 D D D D D D D D CP Q CP Q CP Q CP Q CP Q CP Q CP Q CP Q nCP nOE nQ1 nQ0 nQ2 nQ3 nQ4 nQ5 nQ6 nQ7 SW00019 FUNCTION TABLE INPUTS INTERNAL OUTPUTS OPERATING MODE H = h = L = l = NC= X = Z = = = nOE nCP nDx REGISTER nQ0 - nQ7 L L l h L H L H L X NC NC H H X nDx NC nDx Z Z High voltage level High voltage level one set-up time prior to the High-to-Low E transition Low voltage level Low voltage level one set-up time prior to the High-to-Low E transition No change Don't care High impedance "off" state Low-to-High clock transition Not a Low-to-High clock transition SCHEMATIC OF EACH OUTPUT VCC 27 OUTPUT 27 SW00503 1999 Sep 23 4 Load and read register Hold Disable outputs Philips Semiconductors Product specification 3.3V 16-bit edge-triggered D-type flip-flop with 30 termination resistors (3-State) 74LVT162374 ABSOLUTE MAXIMUM RATINGS1, 2 PARAMETER SYMBOL VCC IIK RATING UNIT -0.5 to +4.6 V -50 mA -0.5 to +7.0 V VO < 0 -50 mA Output in Off or High state -0.5 to +7.0 V Output in Low state 128 Output in High state -64 DC supply voltage DC input diode current VI < 0 voltage3 VI DC input IOK DC output diode current VOUT CONDITIONS DC output voltage3 IOUT O DC output current Tstg Storage temperature range mA -65 to +150 C NOTES: 1. Stresses beyond those listed may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2. The performance capability of a high-performance integrated circuit in conjunction with its thermal environment can create junction temperatures which are detrimental to reliability. The maximum junction temperature of this integrated circuit should not exceed 150C. 3. The input and output negative voltage ratings may be exceeded if the input and output clamp current ratings are observed. RECOMMENDED OPERATING CONDITIONS LIMITS SYMBOL VCC PARAMETER UNIT DC supply voltage MIN MAX 2.7 3.6 V 0 5.5 V VI Input voltage VIH High-level input voltage VIL Input voltage 0.8 V IOH High-level output current -12 mA IOL Low-level output current 12 mA t/v Input transition rise or fall rate; Outputs enabled 10 ns/V Tamb Operating free-air temperature range +85 C 1999 Sep 23 2.0 -40 5 V Philips Semiconductors Product specification 3.3V 16-bit edge-triggered D-type flip-flop with 30 termination resistors (3-State) 74LVT162374 DC ELECTRICAL CHARACTERISTICS LIMITS SYMBOL PARAMETER TEST CONDITIONS Temp = -40C to +85C MIN VIK Input clamp voltage VCC = 2.7 V; IIK = -18 mA VOH High-level output voltage VCC = 3.0 V; IOH = -12 mA VOL Low-level output voltage VCC = 3.0 V; IOL = 12 mA VRST Power-up output Low voltage5 VCC = 3.6 V; IO = 1 mA; VI = GND or VCC VCC = 3.6 V; VI = VCC or GND II Input leakage current Control pins VCC = 0 or 3.6 V; VI = 5.5 V VCC = 3.6 V; VI = VCC IHOLD Output off current Bus Hold current D inputs7 MAX -0.85 -1.2 V 0.8 V 0.1 0.55 V 0.1 1 0.4 10 0.1 1 -0.4 -5 0.1 100 2.0 Data pins4 VCC = 3.6 V; VI = 0 V IOFF UNIT TYP1 VCC = 0 V; VI or VO = 0 to 4.5 V VCC = 3 V; VI = 0.8 V 75 135 VCC = 3 V; VI = 2.0 V -75 -135 VCC = 0 V to 3.6 V; VCC = 3.6 V 500 A A A Current into an output in the High state when VO > VCC VO = 5.5 V; VCC = 3.0 V 50 125 A Power up/down 3-State output current3 VCC 1.2 V; VO = 0.5 V to VCC; VI = GND or VCC; OE/OE = Don't care 1 100 A IOZH 3-State output High current VCC = 3.6 V; VO = 3.0 V; VI = VIH or VIL 0.5 5 IOZL 3-State output Low current VCC = 3.6 V; VO = 0.5 V; VI = VIH or VIL 0.5 -5 VCC = 3.6 V; Outputs High, VI = GND or VCC, IO = 0 0.07 0.12 IEX IPU/PD ICCH ICCL Quiescent supply current ICCZ ICC Additional supply current per input pin2 VCC = 3.6 V; Outputs Low, VI = GND or VCC, IO = 0 4 6 VCC = 3.6 V; Outputs Disabled; VI = GND or VCC, IO = 06 0.07 0.12 VCC = 3 V to 3.6 V; One input at VCC-0.6 V, Other inputs at VCC or GND 0.1 0.2 A mA mA NOTES: 1. All typical values are at VCC = 3.3 V and Tamb = 25C. 2. This is the increase in supply current for each input at the specified voltage level other than VCC or GND 3. This parameter is valid for any VCC between 0V and 1.2V with a transition time of up to 10 msec. From VCC = 1.2 V to VCC = 3.3 V 0.3 V a transition time of 100 sec is permitted. This parameter is valid for Tamb = 25C only. 4. Unused pins at VCC or GND. 5. For valid test results, data must not be loaded into the flip-flops (or latches) after applying power. 6. ICCZ is measured with outputs pulled to VCC or GND. 7. This is the bus hold overdrive current required to force the input to the opposite logic state. 1999 Sep 23 6 Philips Semiconductors Product specification 3.3V 16-bit edge-triggered D-type flip-flop with 30 termination resistors (3-State) 74LVT162374 AC CHARACTERISTICS GND = 0 V; tR = tF = 2.5 ns; CL = 50 pF; RL = 500 ; Tamb = -40C to +85C. LIMITS SYMBOL PARAMETER WAVEFORM VCC = 3.3 V 0.3 V VCC = 2.7 V TYP1 MAX MAX MIN UNIT fmax Maximum clock frequency 1 150 tPLH tPHL Propagation delay nCP to nQx 1 1.5 1.5 3.0 3.0 5.3 4.9 6.2 5.1 MHz ns tPZH tPZL Output enable time to High and Low level 3 4 1.5 1.5 3.5 3.2 5.6 4.9 6.9 6.0 ns tPHZ tPLZ Output disable time from High and Low Level 3 4 1.5 1.5 3.5 3.2 5.4 5.0 5.7 5.1 ns NOTE: 1. All typical values are at VCC = 3.3V and Tamb = 25C. AC SETUP REQUIREMENTS GND = 0 V; tR = tF = 2.5 ns; CL = 50 pF; RL = 500 ; Tamb = -40C to +85C. LIMITS SYMBOL PARAMETER VCC = 3.3 V 0.3 V WAVEFORM VCC = 2.7 V MIN TYP MIN UNIT tS(H) tS(L) Setup time nDx to nCP 2 2.5 2.5 0.7 0.7 2.5 2.5 ns th(H) th(L) Hold time nDx to nCP 2 0.5 0.5 0 0 0 0 ns tW(H) tw(L) nCP pulse width High or Low 1 1.5 3.0 0.6 1.6 1.5 3.0 ns AC WAVEFORMS VM = 1.5 V, VIN = GND to 3.0 V 1/fMAX 2.7V 2.7V nCP VM VM nOE VM VM VM 0V 0V tw(H) tW(L) tPZH tPHZ tPLH tPHL VOH VOH nQx VM nQx VOH -0.3V VM VM 0V VOL SW00020 SW00014 Waveform 1. Propagation Delay, Clock Input to Output, Clock Pulse Width, and Maximum Clock Frequency nDx EEE EEEEEEE EEE EEE EEEEEEE EEE EEE EEEEEEE EEE VM VM ts(H) VM th(H) Waveform 3. 3-State Output Enable Time to High Level and Output Disable Time from High Level 2.7V 2.7V VM ts(L) nOE 0V VM VM th(L) 0V tPZL 2.7V tPLZ 3V nCP VM VM nQx 0V NOTE: The shaded areas indicate when the input is permitted to change for predictable output performance. VOL +0.3V VOL SW00021 SW00015 Waveform 2. Data Setup and Hold Times 1999 Sep 23 VM Waveform 4. 3-State Output Enable Time to Low Level and Output Disable Time from Low Level 7 Philips Semiconductors Product specification 3.3V 16-bit edge-triggered D-type flip-flop with 30 termination resistors (3-State) 74LVT162374 TEST CIRCUIT AND WAVEFORMS 6V VCC OPEN VIN VOUT PULSE GENERATOR tW 90% RL GND VM NEGATIVE PULSE CL 10% 0V RL tTHL (tF) tTLH (tR) tTLH (tR) tTHL (tF) 90% POSITIVE PULSE Test Circuit for 3-State Outputs SWITCH tPHZ/tPZH GND tPLZ/tPZL 6V tPLH/tPHL open VM VM 10% tW 0V VM = 1.5V Input Pulse Definition INPUT PULSE REQUIREMENTS DEFINITIONS FAMILY RL = Load resistor; see AC CHARACTERISTICS for value. CL = Load capacitance includes jig and probe capacitance; see AC CHARACTERISTICS for value. AMP (V) 90% 10% SWITCH POSITION TEST AMP (V) VM 10% D.U.T. RT 90% 74LVT16 Amplitude Rep. Rate tW tR 2.7V 10MHz 500ns 2.5ns tF 2.5ns RT = Termination resistance should be equal to ZOUT of pulse generators. SW00003 1999 Sep 23 8 Philips Semiconductors Product specification 3.3V 16-bit edge-triggered D-type flip-flop with 30 termination resistors (3-State) SSOP48: plastic shrink small outline package; 48 leads; body width 7.5 mm 1999 Sep 23 9 74LVT162374 SOT370-1 Philips Semiconductors Product specification 3.3V 16-bit edge-triggered D-type flip-flop with 30 termination resistors (3-State) TSSOP48: plastic thin shrink small outline package; 48 leads; body width 6.1mm 1999 Sep 23 10 74LVT162374 SOT362-1 Philips Semiconductors Product specification 3.3V 16-bit edge-triggered D-type flip-flop with 30 termination resistors (3-State) NOTES 1999 Sep 23 11 74LVT162374 Philips Semiconductors Product specification 3.3V 16-bit edge-triggered D-type flip-flop with 30 termination resistors (3-State) 74LVT162374 Data sheet status Data sheet status Product status Definition [1] Objective specification Development This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. Preliminary specification Qualification This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Product specification Production This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. [1] Please consult the most recently issued datasheet before initiating or completing a design. Definitions Short-form specification -- The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition -- Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information -- Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support -- These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes -- Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Copyright Philips Electronics North America Corporation 1999 All rights reserved. Printed in U.S.A. Philips Semiconductors 811 East Arques Avenue P.O. Box 3409 Sunnyvale, California 94088-3409 Telephone 800-234-7381 Date of release: 09-99 Document order number: 1999 Sep 23 12 9397 750 06508