MIC2981/2982 Micrel, Inc. MIC2981/2982 High-Voltage High-Current Source Driver Array General Features The MIC2981/82 is an 8-channel, high-voltage, high-current source driver array ideal for switching high-power loads from logic-level TTL, CMOS, or PMOS control signals. * * * * * These drivers can manage multiple loads of up to 50V and 500mA, limited only by package power dissipation. Output voltage to 50V Output current to 500mA Transient-protected outputs Integral clamp diodes TTL, CMOS, or PMOS compatible inputs Applications Micrel's MIC2981/82 features inputs compatible with 5V TTL and 5V to 15V CMOS or PMOS logic outputs. Micrel's dual-marked device replaces either UDN2981 or UDN2982 devices. * Relay and solenoid switching * Stepping motor * LED and incandescent displays The MIC2981/82 is available in the 18-pin plastic DIP and 18-lead wide SOP package. Both devices operate in the industrial temperature range. Ordering Information Reference Part Number Manufacturing* PbFree MIC2981BN** MIC2981/82BN MIC2982BN** MIC2981/82BN Temperature Range Package MIC2981/82YN -40C to +85C 18-pin DIP MIC2981/82YN -40C to +85C 18-pin DIP MIC2981BWM** MIC2981/82BWM MIC2981/82YWM -40C to +85C 18-pin wide SOP MIC2982BWM** MIC2981/82BWM MIC2981/82YWM -40C to +85C 18-pin wide SOP * Order entry P/N. **Orders for MIC2981BN or MIC2982BN will be filled with dual-marked MIC2981/82BN. **Orders for MIC2981YN or MIC2982YN will be filled with dual-marked MIC2981/82YN. **Orders for MIC2981BWM or MIC2982BWM will be filled with dual-marked MIC2981/82BWM. **Orders for MIC2981YWM or MIC2982YWM will be filled with dual-marked MIC2981/82YWM. Functional Diagrams IN1 OUT1 IN2 OUT2 IN3 OUT3 VS 20k 1.8k IN4-IN7 4 OUT4-OUT7 IN 800 IN8 OUT8 VS GND OUT 1.5k GND Typical MIC2891/2982 Source Driver MIC2981 MIC2982 Micrel, Inc. * 2180 Fortune Drive * San Jose, CA 95131 * USA * tel + 1 (408) 944-0800 * fax + 1 (408) 474-1000 * http://www.micrel.com June 2005 1 MIC2981/2982 MIC2981/2982 Micrel, Inc. Pin Configuration IN1 1 18 OUT1 IN2 2 17 OUT2 IN3 3 16 OUT3 IN4 4 15 OUT4 IN5 5 14 OUT5 IN6 6 13 OUT6 IN7 7 12 OUT7 IN8 8 11 OUT8 VS 9 10 GND 18-Pin DIP (N) 18-Pin Wide SOP (WM) Pin Description Pin No. Pin No. Pin Name 1-8 IN1-IN8 Input 1 through Input 8: Base drive to driver input transistor. 9 VS 10 GND 11-18 OUT8-OUT1 MIC2981/2982 Pin Function Supply Input Ground Output 8 through Output 1: Emitter of Darlington driver output. 2 June 2005 MIC2981/2982 Micrel, Inc. Absolute Maximum Ratings Operating Ratings Supply Voltage (VS) ...................................................... 50V Output Voltage (VCE) .................................................... 50V Continuous Output Current (IC) ................................ 500mA Input Voltage (VIN) MIC2981/82 ............................................................... 30V Ground Current (IGND) .................................................... 3A Junction Temperature (TJ) ...................................... +150C Storage Temperature (TS) ....................... -65C to +150C Supply Voltage (VS) ............................................ 5V to 50V Ambient Temperature (TA) ......................... -40C to +85C Package Thermal Resistance PDIP JA .............................................................. 56C/W SOP JA .............................................................. 84C/W Electrical Characteristics(Note 3) VS = 50V, TA = +25C, unless noted. Symbol Parameter Condition Min Typ Max Units ICEX Output Leakage Current VIN = 0.4V, TA = +70C, Note 1 200 A VCE(sus) Output Sustaining Voltage IOUT = 45mA VCE(sat) Collector-Emitter Saturation Voltage VIN = 2.4V, IOUT = 100mA VIN = 2.4V, IOUT = 225mA VIN = 2.4V, IOUT = 350mA 1.7 1.8 1.9 2.0 2.1 2.2 V V V IIN(on) Input Current MIC2981 VIN = 2.4V VIN = 3.85 140 310 200 450 A A MIC2982 VIN = 2.4V VIN = 12V 140 1.25 200 1.93 A mA 35 IOUT Output Source Current VIN = 2.4V, VCE = 2.2V IS Supply Current VIN = 2.4, OUT1-8 = open, Note 1 tON Turn-On Delay 0.5EIN to 0.5EOUT, RL = 100, VS = 35V, tOFF Turn-Off Delay 0.5EIN to 0.5EOUT, RL = 100, VS = 35V, Note 2 IR Clamp Diode Leakage Current VR = 50V, VIN = 0.4V, Note 1 VF Clamp Diode Forward Voltage IF = 350mA V 350 mA 10 mA 1.0 2.0 s 5.0 10 s 50 A 2.0 V 1.5 General Note: Devices are ESD protected; however, handling precautions are recommended. Note 1: Applied to all 8 inputs simultaneously. Note 2: Load conditions affect turnoff delay. Note 3: Specification for packaged product only. June 2005 3 MIC2981/2982 MIC2981/2982 Micrel, Inc. Package Information 0.920 MAX (23.370) PIN 1 0.030-0.110 RAD (0.762-2.794) .2500.005 (6.3500.127) 0.0600.005 (1.5240.127) 0.290-0.320 (7.336-8.128) 0.020 (0.508) 0.040 TYP (1.016) 0.1300.005 (3.3020.127) 0-10 0.020 MIN (0.508) 0.0180.003 (0.4570.076) 0.1000.010 (2.5400.254) 0.125 MIN (3.175) +0.025 -0.015 +0.635 8.255 -0.381 0.325 ( ) 18-Pin Plastic DIP (N) PIN 1 DIMENSIONS: INCHES (MM) 0.301 (7.645) 0.297 (7.544) 0.027 (0.686) 0.031 (0.787) 0.103 (2.616) 0.050 (1.270) 0.016 (0.046) 0.099 (2.515) TYP TYP 0.094 (2.388) 0.090 (2.286) 0.459 (11.659) 0.455 (11.557) 7 TYP 0.015 R (0.381) 0.015 (0.381) SEATING MIN PLANE 0.297 (7.544) 0.293 (7.442) 0.330 (8.382) 0.326 (8.280) 0.022 (0.559) 0.018 (0.457) 5 TYP 10 TYP 0.032 (0.813) TYP 0.408 (10.363) 0.404 (10.262) 18-Pin Wide SOP (WM) MICREL INC. TEL 2180 FORTUNE DRIVE + 1 (408) 944-0800 FAX SAN JOSE, CA 95131 USA + 1 (408) 474-1000 WEB http://www.micrel.com This information furnished by Micrel in this data sheet is believed to be accurate and reliable. However no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. (c) 1999 Micrel Incorporated MIC2981/2982 4 June 2005